Search Documents

By D. Marsh

The feasibility study for the Grasberg Block Cave mine, finalized in May 2008, indicated a production capacity of 160,000 tonnes per day. A rail haulage system was an integral part of the mine design. This paper describes the simulation process used in optimizing the design and discusses the key factors and variables that impact the capacity of the system. The final recommendations for the haulage level layout and associated equipment are also included.

Jan 1, 2010

By J. W. Mausteller

Chemical oxygen supplies have been used for nearly 60 years, with their greatest application during the last 25 years. They are of two types, the superoxides and chlorate "candles", The superoxides are demand chemicals, responding to the needs of the user and to supply oxygen and remove carbon dioxide. Chlorate candles are formed solid element which furnish oxygen only and do not remove carbon dioxide. Properties of these materials will be described, with comments on the respiratory requirements of a man under various workloads, types of equipment which use chemical oxygen, comparison with other systems and potential application to an underground mine survival system.

Jan 1, 1971

By Sheldon P. Wimpfen

Sand and gravel has been, and will continue to be, our principal construction material. Most of us are familiar with the patterns of past growth. Today we will examine the present status of this vital industry. We shall also attempt to look into the future to see where it is going and to evaluate the constraints that are being imposed. Natural aggregates are among the lowest in value of all bulk industrial minerals. From the processing point of view, sand and gravel production is relatively simple since the products are sized materials obtained from a deposit of satisfactory physical soundness. They can be used either loose or bound to provide bulk, strength, or protection. One of the main uses of coarse aggregate is in concrete as a filling material. As a general rule, the coarse aggregate constitutes about three-quarters of the volume of concrete. The other main use for aggregate is as a roadstone or roadbase to provide protective and stabilizing bulk beneath the road surface. Also it is used in a mixture with petroleum products as the wearing course on top. The sand and gravel industry is geographically widespread. In general, the output of operations is directly proportional to the amount of construction in any area. A wide variety of other aggregates compete with sand and gravel, including crushed stone, blast-furnace slag, clinker, and artificial and natural lightweight materials.

Jan 1, 1972

By T. A. Gray

There are several potential large-volume uses for coal ash in mining-related applications that could be environmentally and economically beneficial to mining companies. Actual usage, however, may be constrained by regulations or by perceptions of coal ash and the potential uses. To identify currently allowed uses and to assess constraints to coal ash use in the eastern coal fields, questionnaires were sent to state coal mining agencies to determine their policies on coal ash utilization and to mining companies to solicit their viewpoints on coal ash utilization. Identifying and understanding the constraints will allow for the development of a coordinated and consistent approach to remove or reduce these constraints and possibly allow for increased utilization of coal ash by the mining industry. This paper summarizes the findings of our investigation.

Jan 1, 1995

By K. J. Sollman

With an ongoing concern for safety and health in the workplace, NYCO® requested three medical evaluations be undertaken to study possible health hazards of wollastonite. Two of the evaluations were conducted by the National Institute of Occupational Safety and Health (NIOSH). One was in 1976 (Ref. 1), and the second in 1982 (Ref. 2). The aim of the two studies was to answer the following two questions: 1. Do wollastonite workers exhibit more respiratory abnormalities than workers not exposed to wollastonite? 2. Is there a relationship between prevalence of respiratory abnormalities and accumulated expo-sure time to wollastonite?

Jan 1, 1988

By William G. Wilson

In the U.S. today a number of tentative synthetic fuel plants have been sited by a number of major corporations. Each of these for a number of reasons have deferred construction. The only synthetic fuel plants under active development are those being built with the Energy Research and Development Administration (ERDA) under the authority of the Non-nuclear Energy Research and Development Act of 1974 (Public Law 93-577). Under this Act in joint sponsorship with industry, a series of coal conversion pilot and demonstration plants are being built to produce environmentally acceptable fuels from high sulfur coals. Before entering into a discussion of the factors associated with the siting of the ERDA coal conversion program, the difference between a pilot plant and a demonstration plant should be explained. The terms pilot plant and demonstration plant iridicate a size of plant rahter than technology. A pilot plant will vary from an "add-on" to an existing facility to an independent unit. Demonstration plants are a wholly independent, self contained plants, capable of independent operation to demonstrate the environmenta1, economic, and technica1 feasibility of a technology. These plants are from one-third to one-tenth the scale of a commercial operation and often described as plus 1000 tons per day of coal consumption. Their purpose is stated in the Act (Section 6, (3)(E),) "to accelerate the commercial demonstration of technologies for producing syncrude and liquid petroleum products from coal: Provided. That the Administrator shall invite and consider proposals from potential participants based upon Federal assistants and participation through guaranteed prices or purchase of the products .... " In site selection and plant design it has been suggested that special interest groups should be allowed to dictate the site and specify the design. Under the present program the industrial partner who is contributing 50 percent

Jan 1, 1977

By Bond. F. C.

Introduction Although autogenous grinding applications date back to the early years of mineral processing when tumbling-type mills were first used, there has been a renewed interest in this type of grinding over the past few decades. A review of the historical aspects of autogenous grinding is provided which follows the development of the various types of mills and processes. Wet and dry grinding operations using either autogenous or semiautogenous mills, including the Aerofall mill, are described. Em¬phasis has been placed on the test work required to evaluate the feasibility of using autogenous or semiautogenous grinding for a spe¬cific application. The factors which must be considered to establish the appropriate design criteria for these types of grinding circuits are discussed in detail. Successful application of these grinding circuits results from a thorough test program, a careful analysis of the test results, and a practical engineering approach to the design of the process flowsheet and milling equipment. Certain pebble milling applications, where the pebbles consist of the ore or rock itself, can be classified as autogenous pebble mill grinding, or better known as ore-pebble mill grinding. In the generic sense, pebble milling includes those grinding operations using a tum¬bling mill in which the grinding media consists of various types of pebbles, either ore or other pebbles, instead of metal balls. Conse¬quently, this subject is covered separately in Chapter 5, Pebble Mills. Operating data from many of the installations located throughout the world are included in this chapter. Our appreciation is extended to those companies who contributed this important information. History of Autogenous Grinding F. C. BOND Autogenous grinding, the grinding of ore by itself rather than by special metallic or nonmetallic grinding bodies distinct from the ore, has an old and honorable place in the art of mineral processing. It antedates the use of the rod mill and is only a few years younger than the development of the continuously fed rotating tumbling mill in which it is accomplished. Its history71, 72 is inextricably bound up with that of gold mining. Every important early development of autogenous grinding took place on ores of gold, except in one case of silver ore. In common with many other features of modern mineral processing, autogenous grinding would have been greatly retarded if the winning of gold had been so small a part of mining in the past as it is today. Gold unlocked the secrets of rock-on-rock grinding. In years past gold ores were crushed in stamp batteries and then flowed over copper plates covered with mercury which amalgamated the gold. The McArthur Forrest cyanide process for the dissolution of gold in a dilute alkaline cyanide solution appeared in 1890. With finer grinding it recovered more gold than could be won by amalgama¬tion alone. The first response was to stamp in cyanide solution and finer mesh screens guarding the stamp discharge. However, the fine screens greatly restricted the tonnage stamped, and they wore out rapidly. Rotating tumbling mills70, 73 were the obvious choice to grind the coarse product from stamps. Many of these were Gates tube mills; more than 1,000 of these were sold between 1907 and 1913. They were made in 6, 51h, and 5 ft diam, with lengths of 20 and 22 ft. The 5 x 22-ft size was the most popular. The term tube mill did not refer to the mill shape, but included all tumbling mills using grinding pebbles. The flint or chert rocks found along the coasts of Denmark and Normandy are probably the most durable and resistant to abrasive and tumbling wear of any on earth. They were much used in the early tube mills. The early linings were all silex or Danish flint blocks, cemented into place with portland cement. Local hard stones or cast iron blocks were also used later. The cast iron liners carried lifters and were not bolted to the shell, but were held in a tight circle against it by steel wedges hammered home between them. The first ribbed metal liners designed to hold grinding pebbles pounded into them by the mill action were developed at El Oro, Mexico, about 1905. These and the Forbes, Komata, and Tonopah types, as well as the Osborne type developed in South Africa within about five years, were very successful in reducing liner wear. They sometimes lasted two years or more, and equalled or exceeded the life of silex lining at a lower cost. Some of the types were patented. The pioneer name recorded in the history of autogenous grinding is that of Kenneth L. Graham. In 1907 at the Geldenhuis Deep Ltd. mine near Johannesburg, he ran a comparative test on two tube mills. One mill used pieces of the common gold ore, or banket, and the other used the customary imported Danish pebbles as grinding media. He published the first account of autogenous grinding.'' In a test lasting 81 days the ore pebbles showed a definite saving over the Danish pebbles. Graham's historic paper also describes the invention of B. Chew of the Crown Deep Mines of the first trammel to be attached to a grinding mill discharge. The first known account of autogenous grind¬ing printed outside of South Africa was the description of the Graham test in Mining and Scientific Press's The use of grate- vs. overflow¬discharge was also described at this time." The news of this successful test appears to have had immediate effect, for by the end of 1908 the number of tube mills on the Rand had increased from 72 to 120.76 Presumably, most of these mills were now using autogenous grinding. The ore was principally a hard conglomerate of quartz peb¬bles cemented by silica, and was eminently suitable for use as a grind¬ing media. It is unfortunate that in South Africa the new autogenous process continued to be called by its old name of pebble milling, since the name does not distinguish between grinding with ore and grinding with extraneous pebbles. For increased clarity the former is called rock pebble milling. The first historical stage in the development was what is now designated as secondary autogenous grinding, or rock pebble milling. It consists of grinding a feed all passing 'A in. or finer with ore pebbles about 2 to 4 in. in diameter. The next stage to develop was that now called intermediate autogenous grinding, where larger amounts of larger pebbles about 5 in. in size were used to grind ore which had been crushed to about rod mill feed size or somewhat finer. It was developed on the Rand and in other places where coarse stamp screens were used to increase mill tonnage. In many cases the early secondary and intermediate autogenous mills have now been replaced by conventional ball mills and rod mill-ball mill circuits, with the object of further increasing grinding capacity. The third stage to develop is designated as wet primary autogenous grinding, in which run-of-mine ore or a primary crusher product is all fed to the autogenous mill together. It developed many years later indepen¬dently in the United States and in South Africa. The fourth and most recent stage is that of dry primary autogenous grinding, which developed in the United States and Canada. All four stages originated in gold mining. The first use of commercial autogenous grinding outside of the Rand apparently took place five years later in 1912 at the Santa Gertrudis gold mine at Pachuca, 55 miles northeast of Mexico City. This was followed closely by an installation at Goldfields, Nevada, in 1914-1915. The first name associated with autogenous grinding

Jan 1, 1985

By Norman Weiss

The purpose of this paper is to relate progress in the engineering field called Minerals Beneficiation to undergraduate and graduate education in our colleges and universities. So mach has been written recently about the education of scientists and engineers that I've had to struggle against the temptation to repeat what has been often said before, particularly because man like Robert Mehl of Carnegie Tech, Antoine Gaudin of MIT, H. M. Davis of Penn State, and John Vanderwilt of Colorado School of Mines have recently written many quotable paragraphs on the subject. In the matter of progress, the rapidity of proliferation in the area of physical and chemical beneficiation is convincing proof that this is indeed a lively art, and having been a millman for 35 uninterrupted years I prefer to lean on personal observations to some extent, rather than on statistics and charts v culled from the journals. I propose in this paper to talk first about the progress we've made in our branch of the mining industry in the last 3 decades--particularly in the last few years--and try to show that future progress will depend upon the quality of education and capacity for research possessed by our colleges. The second part will deal with some of the problems the colleges encounter in trying to fulfill these responsibilities.

Jan 1, 1959

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

By W. J. Schlitt

Introduction Heap and dump leaching are low-cost metal production techniques that are gaining in popularity among gold and copper producers. However, the flow of solution in heaps and dumps has received little attention in the literature. This is unfortunate since solution flow is one of the few parameters subject to operator control. Thus, solution management may well influence both operating costs and plant performance. Costs aside, there are two important aspects of solution flow to be considered -the metallurgical and the hydrological. Some of the metallurgical factors have recently been discussed (Jackson and Ream, 1980; Schlitt, 1984; Schlitt and Nicolai, 1987). These cover solution application rates and methods, irrigation rates, leach-rest cycles, and nonvertical solution flow. According to Caldwell and Moss (1985), however, the hydrological aspects may be more significant than the metallurgical ones. In particular, a phreatic surface will form when excessive flow leads to an accumulation of water and the associated buildup of pore pressure within the rock pile. Such internal flooding can either originate at the foundation or at some other zone of very low permeability. The latter condition gives rise to an impounded volume of solution, i.e., a perched water table (see Whiting, 1985). Caldwell and Moss point out that a rising zone of saturation is probably the most common cause of dump failures. Of course, such failures have even occurred in heaps that were carefully prepared for leaching (Milligan and Engelhardt, 1984). Thus, flooded conditions and perched water tables represent an important safety consideration as well as having an impact on metallurgical performance. The following sections describe a case history in which a perched water table developed within a copper leach dump. The description includes background information, solution flow rates, and metallurgical data. Then this situation is compared to one involving normal drainage. Description of the leach system The leach dump in the case history is located at a shutdown open pit copper mine. It was built in two lifts, with the second added some 20 years after the first. There is little detailed information available on the initial lift. It was built with rail¬hauled waste and was generally less than 30 m (100 ft) high at the crest. The area available for leaching was about 120 m (400 ft) wide and more than 380 m (1250 ft) long. The dump surface was prepared for leaching by dozing ponds approximately 12 m by 12 m by 2.5 to 3.0 m deep (40 ft by 40 ft by 8 to 10 ft). The ponds were leached by flooding with barren leach solution returned from a scrap iron cementation plant. Based on mill feed at the time, the average waste grade was probably close to 0.4% Cu. The first lift leached well. It accepted high flows, which together with the waste grade, produced a rich pregnant leach solution (PLS). Old records indicate a PLS of "50 lb Cu/ 1000 gal," or about 6 g/L. As later drilling would indicate, such a high tenor led to dissolution of considerable scrap iron that was returned to the dump. The iron then hydrolyzed and settled out on the pond bottoms. In addition, the waste settled substantially so that the unleached crest was 3.0 to 4.5 m (10 to 15 ft) above the ponded area. Eventually, the leachable copper was extracted and the dump became less permeable. Thus, the PLS tenor dropped until it became uneconomical. About ten years later, mining resumed and the decision was made to add another lift to the dump. This was done without giving much thought to a subsequent leach operation. Hence a 24-m (80-ft) lift was built on top of the original dump. The surface of the latter was not prepared in any way, e.g., by leveling and/or deep ripping, prior to over-dumping. Examination of subsequent drill cuttings indicated that the new lift contained about 0.2% Cu, with chalcopyrite and chalcocite (50:50) being the predominant copper minerals. Most of the chalcocite occurred as rimming on the abundant pyrite, with the pyrite to chalcopyrite ratio estimated at 10 to 1. The use of 100- and 120-ton trucks for haulage caused some waste compaction during emplacement. In addition, the host rock itself was relatively soft, being a porphyry intrusive material that was partially altered to clay. As a result of the initial compaction and clay swelling, the rate of water percolation from the new leach ponds was slow and the ponds often contained considerable standing water. Even frequent ripping failed to provide a sustained improvement in the percolation rate. The poor surface permeability was exacerbated by hydrolysis of iron salts which settled as a layer on the pond bottoms. Partly as a result of the permeability problems, metallurgical performance was not up to expectations. These had been based on laboratory tests which showed about 20% copper solubilization in two weeks. Continued copper extraction in the tests also suggested that a substantial percentage of the copper would eventually be recovered. However, the PLS grade in the actual operation peaked briefly at about 0.48 g/L Cu (4 lb Cu/1000 gal), then declined to a range of only 0.24 to 0.36 g/L Cu (2 to 3 lb Cu/1000 gal). The poor leaching was traced to a lack of oxidation of the sulfides. There were two principal observations supporting this conclusion. First, there was no evidence of any heat being generated within the dump. As discussed elsewhere (Schlitt and Jackson, 1981; Hiskey and Schlitt, 1982), pyrite oxidation is quite exothermic and the high pyrite content of the waste should have led to an increase in the temperature of the leach solution as it percolated through the rock pile. Second, there was no sign of any natural convective air flow through the dump.

Jan 1, 1987

By G. E. S. Valadao

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake pore microstructure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 µm, length of 500 µm and height of 4000 µm. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: I) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method, 2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4) some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By W. Burger

For the development of deep hard rock mines fast access to the orebody is critical. In some cases the mineralized area is more than 1500 m (5000 ft) below surface. Excavation of shafts or declines is typically on the critical path of the project schedule. Saving time on those activities can significantly increase the net present value of the mining project. Mechanical excavation methods are a step-change in excavation performance and labor safety compared to drill and blast operations. In hard rock conditions roadheaders can not be used effectively, so disc cutting is the first choice. For excavation of declines tunnel boring machines (TBM) can be used in many cases. These provide in certain rock conditions considerably higher production rates compared to drill and blast excavation.

Jan 1, 2010

By R. Keith Evans

Potential large scale uses in secondary battery systems and fusion reactors together with a steady increase in demand for conventional applications, particularly in aluminum smelting, has resulted in an increasing interest in lithium and its compounds. Current world requirements are met from both granitic pegmatites and non-pegmatitic sources and although the emphasis in this short paper is on the pegmatitic minerals, and, in particular, on their "direct usage" applications, a short summary of other sources and requirements for chemical production is included for the sake of completeness.

Jan 1, 1977

By N. D. Jagger

In order to maximize the benefits obtained from flocculating agents when used as settling aids in high rate and conventional thickeners, it is often necessary to dilute the thickener feed prior to flocculant addition. In some cases, no flocculation at all is possible unless dilution water is used. The most common method of diluting thickener feed has been to recirculate some of the thickener overflow by means of a centrifugal pumping system. This represents a significant capital and operating cost. Supaflo Technologies of Australia has developed and patented an internal recirculation method known as Auto Dilution (or "Autodil") which is based on the principle that an hydraulic head differential exists between the inside and outside of the feedwell because of the higher S. G. of the pulp inside the feedwell, By installing non-return ports in the feedwell wall at the appropriate level, supernatant solution flows into the feedwell at a calculated rate and dilutes the feed without any need for external recirculation of overflow.

Jan 1, 1993

By C. H. Bucknam

Acid neutralization titrations were applied to the characterization of soil and overburden for the control and prediction of acid rock drainage in the coal fields of the eastern United States in the 1970?s (1). These became known as the Sobek methods as a result of the early United States Environmental Protection Agency publication and the methods have been modified (2) to be adapted to many applications in the metal mining sector (3,4,5,6,), and, as a result, there are a large number of acid neutralization potential methods being used that are referred to as Modified Sobek methods. Standardization of neutralization potential methods for metal bearing ores and related materials based on carbonate carbon, rather than titration, commenced in the 1990?s through the American Society of Methods and Materials (ASTM) Committee E01 on Analytical Chemistry for Metal Ores and Related Materials Subcommittee E01.02 on Ores, Concentrates and Related Metallurgical Materials (7). A subcommittee section, E01.02.05 on Environmental Methods, was organized to coordinate the method and material standardization efforts of ASTM and the Acid Drainage Technology Initiative Metal Mining Sector (ADTI-MMS) Prediction Committee (8), which took on the project of standardization of the acid neutralization potential acidity titration method (ANPA) to supplement the carbonate carbon method in E1915 (9) for application to samples which have metal carbonates (10), in particular, which result in overestimation of the neutralization potential using the carbonate carbon methods (11).

Jan 1, 2010

By D. Greene

Close integration of mine planning and operation is a long-sought goal. Success is achieved in varying degrees depending upon mine complexity, size, and sophistication, but too often is more limited than desired. Despite tremendous strides in the development of computer-aided mine planning, digital plans usually must still be converted to error-prone paper maps and physical ground surveys for actual excavation and reclamation. However, advances in GPS, operator displays, and mobile computers now enable equipment operators to work directly from on-board digital plans. CAES offers reduced survey costs, faster field transition time and improved excavation accuracy coupled with faster, more informed decision making regarding key mining operations.

Jan 1, 1997

By H. Suharyono

The results of an experimental study of polymer-induced flocculation of clay suspensions in continuous, stirred-tank reactors are presented. The effects of polymer dosage, mixing time and mixing intensity are shown to be generally similar to those observed for equivalent batch systems, but flocculation appears to be generally less effective in the continuous process. Settling rates are lower and supernatant turbidities are higher for the continuous system. It is postulated that non-equilibrium effects due to simultaneous polymer adsorption and floc growth can be exploited so as to enhance flocculation in batch systems. The nature of the continuous process, however, offers less opportunity for taking advantage of such effects. Conditions in a continuous flocculation system inherently lead to a closer approach to equilibrium.

Jan 1, 1994

By Robert J. Pruett

The Georgia kaolin District is the world's largest producer of kaolin. Georgia production tripled from 2,344 million metric tons in 1964 to 7,570 million metric tons in 1994. Development of the Georgia kaolin industry can be traced to the mineral resource, the adoption of innovative process technologies, and the market growth for kaolin. Georgia kaolin is an abundant and high-quality resource that shows a range of advantageous properties. Technical developments in wet processing, delamination, and calcination allowed production of high-value products. The application of kaolin pigments to the paper industry provided a market that could absorb rapid growth.

Jan 1, 1998

By R. Sandefur

Recent advances in personal computer technology allow movies of various types to be made and displayed on PC and Macintosh computers. An interesting application of this movie technology is animation of computerized geological models. These movies, which can be most easily constructed along rows, columns, and benches of block models, allow an ore body to be more easily and quickly visualized than the traditional method of flipping back and forth through various sections.

Jan 1, 1994

By S. K. Sharma

The Bureau of Mines' rapid method of dewatering fine-particulate slurries uses extremely high molecular weight polymers. These polymers form large, strong flocs which can be dewatered by sieving or sedimentation. However, sometimes these flocs deteriorate rapidly if water is not removed immediately. During field tests, clay slurries have been encountered that could have been dewatered economically if it were not for the rapid floc deterioration. A kinetics study was conducted to determine the rate of kaolin-PED floc degradation in which polymer addition, to bring the flocs back to their original condition, was used to determine the extent of floc decay. Results showed that the amount of polymer added, to replace polymer lost by spreading, was less for the lower PEO concentrations. For this clay-polymer system, floc breakage as judged by polymer additions followed first order kinetics. It was also found that the addition of fluoride ion stabilized the kaolin flocs.

Jan 1, 1992