Search Documents

By Walter E. Heinrichs

This case history really started during the tail end of WWII when two Navy men, both Colorado School of Mines graduates, got together in Washington, DC, while they were assigned to the Office of Navy Petroleum Reserves doing some of the first aerial magnetometer work ever done on a practical oil exploration basis over the offshore area of the Gulf Coast. When separated from Naval Service active duty in 1946, the two men, Walter E. Heinrichs, Jr., and Robert E. Thurmond, tried, unsuccessfully, to form a commercial air magnetometer business. Later they got together again in Jerome, AZ, with Newmont Mining's early geophysical exploration endeavors from 1947 to 1949. Subsequent to the Newmont experience, they jointly proposed a specific mining geophysical exploration and development program to Herbert Hoover, Jr., then president of United Geophysical Co. of Pasadena, CA. Mr. Hoover, in consultation with his father Herbert Hoover and others of his staff at United, particularly Edwin G. Schempf, executive vice president, and Raymond A. Peterson, vice president of research, agreed to establish the proposed program under United's auspices, to be headquartered at Tucson, AZ. The primary objective would be to practically test and develop various mining geophysical methods and techniques while exploring particularly for base metals in the general area of southeast Arizona and southwest New Mexico.

Jan 1, 1991

By Patrick J. Doig

The Crosstown 7 Collector System, Contract C28G11, is part of the Milwaukee Metropolitan Sewerage District's Waste Pollution Abatement Program. The contract involves the construction of 1.6 km (1 mile) of 3 m (10 ft.) diameter tunnel in soft ground. The tunnel is 10 m (35 Ft.) below surface and passes through a variety of soils. The eastern leg of the tunnel along Bruce Street is mainly in till material, a stiff, relatively dry clay. The northern leg along 16th Street starts in till, and continues in estuarine deposits - moist sticky clay, with intrusions of alluvial sand and gravel. The contract specifications required that the tunnel be constructed either under compressed air or with an earth pressure balance tunnel boring machine. The S. A. Healy Co., the general contractor, chose the latter option. Additionally, a single pass, pre-cast concrete segmental liner was selected as the lining system. The mining machine was manufactured by Lovat Tunnel of Canada and the segments were made by the Sehulster Company of Milwaukee. The use of this combination of machine and lining is relatively new to the United States and this tunnel is the most extensive built to date with a gasketed, segmental single pass lining for transportation of fluids. This paper details the various aspects of the construction of the tunnel and associated shafts.

Jan 1, 1989

By Thomas C. Anderson, Terry Weiss

The Mount Gunnison No. 1 Mine of the West Elk Coal Company (wholly owned subsidiary of ARCO Coal) had secured contracts to provide low sulfur, high Btu steam coal to various utility companies. This called for the development of the B-Seam at the Mount Gunnison Mine located some 400 feet below the operating F-Seam workings being mined with conventional room and pillar techniques. The B-Seam, to meet production goals, will be mined by a new 600-foot longwall machine making a 13-foot high cut. American Mine Services was awarded a competitively bid contract to drive two 2000-foot, 13-foot by 16-foot slopes at -15 percent, sink a 16-foot diameter ventilation shaft 400 feet between the F- and B-Seams, install a 60-inch conveyor in one of the slopes, remove 7000 feet of existing conveyor and rehabilitate 7000 feet in two entries to accommodate the placement of the longwall machinery. The slope portals were located 7000 feet in by the surface portal. Unique to the project was the placement of work shops and other infrastructure 7000 feet underground with an entry height of 6 feet. The $7 million contract was completed in less than one year using a mix of permissible (Schedule 31) and standard (Schedule 24) LHD equipment, all pneumatic jumbos and shaft sinking gear.

Jan 1, 1993

By E. Grygiel, J. Haynes, T. McNider

Jim Walter Resources Blue Creek No. 3 Mine was opened in one of the most gassy coal beds in the United States. Although face ventilation requirements exceeded 14,000 cfm (6 .6m3/s) air, continuous miner sections experienced an unacceptable frequency of frictional ignitions. Modifications offered primarily by the U. S. Bureau of Mines such as diffuser fans, water spray fans, and slow speed cutting motors were used with little success. However, laboratory tests conducted at the U. S. Bureau of Mines indicated that an increase in bit attack angle from 50° to 55°-57° significantly reduced the chances of the bit causing a frictional ignition. An experimental miner drum was built using this concept coupled with a new bit designed by the Bureau and manufactured by Hughes Tool Company that better protected the bit steel shank with a carbide cap. It was installed on a continuous miner and placed in an area of the mine prone to ignitions. 50,000 tons (45,500 metric tons) of coal were cut without a frictional ignition. When the miner was withdrawn for rebuild and a machine with an unmodified cutting drum placed in service, two ignitions occurred before 10,000 tons (9,100 metric tons) were mined. Other machines have been rebuilt and are in service, and to date none have been known to cause an ignition.

Jan 1, 1987

By G. T. Lineberry, W. J. Wiehagen, L. L. Rethi

This paper discusses a practical method for enhancing the performance of mining work crews. The method, described as the Work Crew Performance Model (WCPM), seeks to define performance variability within similar tasks of an underground work crew. Key components of the WCPM include: •job definition through task analyses, •the ranking of job elements by perceived cost consequence, •observational techniques to establish performance baselines, and •cost linkages between adherence to task procedures and measures of consequence for noncompliance. The components of this model emphasize a reliance on learning from a veteran work force and using that information to reinvest in strategies to enhance safety and efficiency. These strategies are not limited to technological efforts but include consideration of the so-called "soft-skill technologies, " aimed at reducing variability in individual performance and at effecting a continuous improvement in overall system effectiveness.

Jan 1, 1996

By A. Subbotin

During developing the Ingulska mine at the Mi-churinske uranium deposit in the central part of Ukraine the radioactive rock dumps have been piled. A height of dumps reaches to 15-25m. They occupy a large territory and can be a source of covering with radioactive dust the area around the Ingulska mine. Uranium content exceeds 0,01% in all dump rocks samples while in the dust fraction samples it ranges from 0,01 to 0,06%. Uranium content in road dust at the dump?s foot reaches 0,137%. A new (for Ukraine) method of f-radiography of tree and bush leaves sampled at the territory about 100km2 has been used. It is based on fission of 235U nucleuses due to heat neutron influence in a nuclear reactor and on following study of the Lausan films with tracks drawn by the fractures of these nucleuses. Uranium content of the dif-fusion-disseminated dust type is (0.9-22.2)?10-6% while in the individual particles it can be considered much more because of burned holes in Lavsan above them. The dust content with uranium in Kirovograd reaches to 20-50 part/cm2 while near the dumps it ranges from 100 part/cm2 to 300 part/cm2 in the radius of 1,5-2km from the Ingulska mine.

Jan 1, 2005

By Robert L. Runkel, D. Kirk Nordstrom, James W. Ball

Low-flow reactive-transport processes in Wightman Fork downstream of the Summitville Mine, south-central Colorado were simulated using the OTIS and OTEQ solute-transport models. The simulation was calibrated using data from a synoptic study conducted during October, 1998. Discharge over the 8-km reach from just below the mine site to the Alamosa River confluence ranged from 0.077 to 0.17 m3/s; travel time was 10.7 hours; pH ranged from 4.6 to 5.7. Simulations revealed that mass balance for SO4 was maintained, and that pH, Fe, and Al were non-conservative. Simulations allowing hydrous ferric and aluminum oxide or hydroxysulfate precipitation matched observed water quality conditions more closely than simulations without precipitation.

Jan 1, 2000

A portable electronic instrument was developed which will measure change of longitudinal wave velocity with change of uniaxial stress in rock columns. The instrument is a solid-state device powered by nickel-cadmium batteries. It uses a probe of two piezo-electric crystals spaced inches apart to send and receive a pulse through a stressed rock. A one-inch cathode ray oscilloscope visually displays the longitudinal wave. A reference chart is used to find the stress. Laboratory results have indicated that the average stress on a sandstone column can be found to within 35 psi. The feasibility of using this instrument to determine stresses in mine pillars is to be studied. The instrument may be used to investigate physical properties of rock.

Jan 1, 1970

By J. M. Ekenes, C. A. Caro

"New approaches that increase hydrometallurgical recovery from refractory minerals in below mill cutoff -grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyritebearing ore at Freeport-McMoRan’s mine in Morenci, AZ. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation. Introduction The Morenci ore deposit, located in eastern Arizona, has been mined for copper for 140 years. Mineralization in the Morenci district consists of sulfides and oxides. To process these ores, Morenci operates concentrator and leaching circuits. Leaching accounts for two-thirds of the copper produced in Morenci. More than one-half of this leaching-derived copper production comes from run-of-mine (ROM) stockpiles. The largest category of material moved in Morenci is destined for ROM stockpiles and waste dumps. Materials that are not economic to mill or leach are designated “waste.” However, this designation can change based on improvements in extraction technology and commodity prices. Chalcopyrite does not leach well due to its refractory nature. For predominant chalcopyrite mineralized ore, copper recovery during a typical leaching cycle may be as low as 5%. For this reason, chalcopyritedominant ores below mill cutoff grade have historically been classified as waste. By incorporating advanced leaching technology to improve metal recovery from previously leach-resistant ore types such as chalcopyrite, the Morenci Mine has been able to reclassify substantial amounts of this “waste” to “ore.” Process chemistry Chalcopyrite copper extraction is temperature, oxygen and ferric dependent. The temperature is achieved primarily by pyrite oxidation (Eq. (1)) and secondarily by oxidation of chalcopyrite itself (Eq. (2)). The regeneration of ferric in solution can be enhanced by providing the appropriate acid and oxygen levels according to Eq. (3). In the absence of microorganisms, this reaction is very slow."

Jan 1, 2015

By Lukas Walder, Roland Arnold, Raphael Zuber, Richard Gradnik

This paper presents the construction of the ventilation shaft for the single-tube, doublelane Kramer tunnel. The project is located in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of Garmisch-Partenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million incl. VAT (US-Dollar 201 million), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for singletube tunnels is solved by a parallel escape tunnel passable for vehicles. For tunnel ventilation, an intermediate shaft has been designed with a depth of approximately 90 m (295 feet) and an inner diameter of 4.5 m (14.8 feet). All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). The geological and hydrogeological conditions, the change in the profile (from round to square geometry), and also the shaft being located at a high elevation presented a demanding technical and logistical challenge. The site arrangement with the pit bank was located in a cut, the slopes of which had to be stabilized with shotcrete and soil nails. This excavation was carried out from the fall of 2020 to the beginning of 2021 because construction operations had to be completed outside the nesting period of protected birds.

Jun 13, 2023

By B. K. Sternberg

Since 1986, we have developed a series of electromagnetic (EM) sounding systems at the Laboratory for Advanced Subsurface Imaging (LASI). These may be categorized by their frequency ranges: low frequency (LF, 30 Hz to 30 kHz), medium frequency (MF, 1 kHz to 1 MHz), and high frequency (HF, 30 kHz to 30 MHz). We have applied these EM systems to a variety of targets, including: mapping of plumes of contaminated groundwater, tracing leachate for an in-situ leaching operation, locating buried hazardous waste, identifying subsidence-prone zones and detecting buried voids. These systems are also applicable to exploration for ore bodies. Currently, our sounding system uses a vertical magnetic field vector. Previous systems of this type required a slow and relatively inaccurate manual rotation of the sensing coils. The systems also used occasional calibrations of the measuring system. We have developed a 3-dimensional mathematical rotation procedure for the data, as well as a simultaneous, high-accuracy, calibration method. These new developments have greatly increased the speed of the measurements, as well as improving the accuracy of the ellipticity data. We use stepped-frequency measurements along with narrow-band filtering to allow accurate measurements, even in high-noise areas. We typically obtain ellipticity measurements at eleven frequencies and along densely sampled profile lines. We use neural networks to help interpret the measured ellipticity patterns. Neural networks can be trained to relate the measured ellipticity patterns to earth resistivities or to discrete targets buried in the earth. The neural network training may use theoretical EM responses calculated from computer codes for relatively simple structures. The theoretical EM response for many complex targets that are of interest cannot currently be reliably calculated, even with the largest supercomputers available. We have therefore chosen to do some of the training using theoretical EM responses generated in a full-scale modeling tank located at our Avra Valley Geophysical Test Site. We have also developed data-visualization software to help interpret the large data sets produced by this system.

Jan 1, 1997

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonite to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath. 1986 and personal communication). These bentonite; typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X- ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated bentonite to the oilfield since specifications are

Jan 1, 1990

By G. P. Larson

We define a specialized mineral market as follows: Specialized markets occur where a low volume of a given mineral is used to convey a large benefit to a specific product. Sales of these value added minerals to small markets generally require a different marketing approach than bulk or commodity markets for traditional minerals. Specialized markets are differentiated by several characteristics as listed in Table 1. [Table 1-Characteristics of Specialized Markets 1. Long-term sample evaluation 2. Small volume markets 3. Highly controlled properties 4. Customized specifications 5. Technical selling effort] Many of the specialized markets require long term evaluations before sales can be made. This can vary greatly depending on the type of industry and ultimate end-use of the final product. In some cases, complete evaluations may take from several weeks to years. Length of sample evaluation has no relationship to size of market. That is, the total market may be quite small or fairly large (e.g. from a few hundred pounds to a few million pounds). Uniformity of value added minerals from lot to lot is an extremely important characteristic for these markets. Variations that are of no consequence to one industry (or application) cannot be tolerated in another. This has led to customized specifications and test procedures for specific markets and applications. Because of the greater uniformity and customized specifications, the need for greater technical selling effort is required. This is particularly true in the initial developmental phases and contacts as well as in maintaining the account after the initial order. A small entrepreneurial organization can be used to advantage to achieve goals of sales and profit to these types of markets. The large commodity or bulk producer's sales and marketing organizations are not ordinarily equipped to give the necessary service or technical assistance to the specialized markets. The organization usually required for this type of marketing is given in Table 2. [Table 2- Specialized Marketing Organization Requirements 1. Flexible approach to technical and marketing problems 2. Versatile background in a broad range of industries 3. Laboratory backup when necessary 4. Marketing expertise 5. Technically competent management] In developing specialized markets, a flexible approach to both technical and marketing problems is necessary in understanding the needs and requirements of the industry and the applications involved. This flexibility is also helpful in adapting existing products to new market areas. Having knowledge of a range of industries as broad as possible can be very helpful. It often happens that a product developed in one area or industry can lead to its application in a different area with excellent results. Laboratory assistance for a wide range of tests and test procedures is an important asset in any development program for specialized markets. Laboratories can also assist in competitive evaluations. Marketing expertise and a management with some degree of technical understanding are necessary in to assign proper cost/ benefit ratios to a proposed new product or application of existing products. This is important since the total market volume can be small and the time required for initial contact to first sale can often be lengthy. Also, management's technical and marketing expertise is required in evaluating all possible options that can be considered viable when an application is presented. Once an organization of this type is in place, it is then possible to determine the needs of the marketplace, including when various minerals might have to be customized to fill those needs. There are generally two methods of marketing, as noted in Table 3. [Table 3- Method of Marketing 1. Product Driven -Develop a product with certain desirable properties and try to find a market to utilize those properties. 2. Market Driven -Know market well enough that when a need arises, it is possible to identify a product that will satisfy the need.] These approaches are not mutually exclusive and can be used at the same time. Marketing a value added mineral generally requires the "market driven" approach. Hence, the importance of a knowledgeable management as outlined above. To determine where needs and opportunities exist, several approaches can be used. Table4 lists some of the methods employed.

Jan 1, 1993

Sweden is beginning to reap the rewards of a process that has transformed a country with a history of metal mining into one of Europe's most vibrant exploration regions. Exploration and mining companies from North America, Europe and Australia have joined local firms in the search of gold, base metals and diamonds. This has been due to changes in Sweden's mining laws in the early 1990s. These changes opened the way for unhindered private sector investment in the country's mineral industry. More than 20,000 km2 (4.9 million acres), mainly in northern Sweden, is now held under granted or applied exploration claims. Exploration permits diamonds, applied or granted covers more than half of Sweden's surface. This is a greater proportion of the country than ever before. Major mining companies and junior explorationists are evaluating a geological potential that bears favorable comparison to other major mining centers. Historically, Sweden's gold re- sources occur in greenstone belts in northernmost Sweden and in association with massive sulfide deposits in the Skellefte district. These are receiving particular attention by exploration companies. In addition, new areas in Sweden are also being explored for gold. This increases the probability that Swedish gold production - already the highest in Europe - will increase in the future (Table 1). Sweden's recorded mining history goes back for much of the last large pool of expertise in exploration, mining, equipment manufacturing and minerals industry research. In addition, the Geological Survey of Sweden provides sup- port for exploration in terms of data archives, processing and publications. Other benefits for exploration companies are Sweden's communications infrastructure, its member- ship in the European Union, bringing access to one of the world's major markets and the high level of educational, technical and language skills held by the country's work- force. And deregulation of the economy and the introduction of competitive corporate tax rates have made Sweden a favorable destination for investment in Europe.

Jan 1, 1997

By J. A. Finch

The photographic measurement of bubble diameter is tedious and restricted to vessels with transparent walls and relatively low bubble concentrations. A new method for predicting bubble diameter in a flotation column has been developed and confirmed by comparison with measured mean bubble diameter (Yianatos et al., 1987) Flotation columns are not mechanically agitated. This note describes an extension of Ms method to a mechanically agitated flotation machine. A recent publication by Szatkowski (1987) provided sufficient data to calculate bubble diameter by the proposed method and compare with values determined photo- graphically. Method In a two-phase system (gas and liquid), bubble diameter (db), superficial gas rate (Vg) and liquid rate (Vl), and gas holdup (Eg) are linked by two relationships (see the nomenclature at the end of the paper for definitions of symbols). [ ] Equation 1 is the definition of slip velocity (relative gas to liquid velocity) for a countercurrent gas-liquid system, and equation 2 is an adaptation (Yianatos et al., 1987) of the expression of Masliyah (1979) for hindered settling in a multispecies system. The solution for bubble diameter is by repetitive substitution of estimates of db in equation 2 until the calculated Ubs is equal to the measured Ubs in equation 1. Results and discussion Table 1 presents the data obtained by Szatkowski (1987) from a mechanically agitated laboratory flotation machine. The machine generated bubbles by directing a gas stream into the vicinity of a disk rotating at Ngh speed (up to 8000 rpm) in the flotation slurry. The air was completely dispersed in a swarm of fine bubbles. A photographic technique was used to determine the distribution of bubble size. The mean diameter and standard deviation were then calculated. Table 1 provides all the information necessary for computing bubble diameter (Vl is assumed zero). The calculated bubble diameter is presented in Table 1 as d;. Figure 1 plots measured versus calculated bubble diameter and shows reasonable agreement between values. There is an apparent tendency to undercalculate the small bubbles and overcalculate the large ones.

Jan 1, 1987

By S. K. Kawatra, A. K. Bakshi

Mineral suspensions in water show Newtonian flow properties at low percent solids. However, this changes to a non-Newtonian regime as the pet-cent solids increases. For Newtonian fluids, viscosity is independent of shear rate, hut, for non-Newtonian fluids, viscosity varies with shear rate. Therefore, if the slurry is non-Newtonian, attempting to measure the viscosity at a shear rate different from the shear rate experienced by the fluid within the process is futile. This is especially true for a hydrocyclone, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between the viscosity and the process efficiency. A new technique to distinguish such changes inflow type was developed. This involves two viscometers: a coaxial cylinder-type viscometer that measures apparent viscosity at low shear rates and a vibrating sphere-type viscometer that measures the apparent viscosity at high shear rates. For each of these instruments, special precautions were taken to allow, for the measurement of the viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer is operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica (80% passing 65 µm) in water was used to prepare slurries at concentrations ranging from 10% to 70% (by weight) solids. The viscosity of each slurry sample was measured simultaneously by both viscometers, and the results were compared. With this technique, it was found that all of the silica-slurry samples tested were in the Newtonian flow regime for up to 70% (by weight) solids. Methocel and Cellosize polymer solutions showed clear non-Newtonian behavior using this technique. This confirmed that non-Newtonian behavior of the silica slurries, if present, would have been detected by this arrangement.

Jan 1, 1997

By J. E. Powell

Introduction The disposal of mine tailings, development rock, and other unwanted refuse material underground in mines by using pneumatic conveying techniques has been undertaken in the coal industry for many years. Similar equipment has been utilized for backfilling hard rock mines and is currently being applied in a gold mine in South Africa where development rock is being stowed in the mined-out stopes to help reduce the incidence of rock outbursts. On a limited scale, pneumatic conveying has been applied for backfilling uranium mines and one particular mine in New Mexico, U.S.A., has used this technique for 8 years. Other uranium mines in this area are now considerinq the dry backfill technique to eliminate the problems associated with hydraulic fill. The need to backfill in uranium mines is primarily of importance to improve ventilation, stabilize the pillars and roof, and possibly to extract a larger percentage of the uranium ore. If this can be achieved by utilizing the tailings from the beneficiation plant and using rock from the development headings which in itself may be slightly radioactive, then a greater benefit can be derived. Backfill can be achieved with hydraulic fill methods by running slurry into the stopes and allowing the water to decant and return through the footwall development entries to sumps for pumping to the surface. However there are several disadvantages associated with this method in that water is percolating throough the mine workings; it is necessary to build bulk heads in flat lying deposits; it is difficult to fill right to the back; and the decanted water takes with it quantities of the finer sand particles which results in maintenance problems with the mine pumps. Pneumatic conveying can overcome these problems in that the voids can be completely filled with high degree of compaction, heavy bulk heads are not necessary, the development rock can be added to the pneumatic system for disposal underground so eliminating hoisting cost to the surface, and cement can be added to the wetted material. To

Jan 1, 1980

By M. S. Kabibwa, E. K. C. Chanda

In planning for the future, Nkana Division deepened the Mindola sub-vertical shaft which was commissioned in 1994 in order to access the 30 Mt of ore between 1274 and 1570 m levels. The Nkana Synclinorium which is estimated to contain 250 Mt of ore is being accessed from the vicinity of Central Shaft. These areas are being planned with the intention of maximizing the use of computers in geological modelling and mine design so as to overcome the inadequacies of manual planning techniques. As a result, there is an increased demand for quality output from the computerized mine planning system the division has been developing over the last few years. A new workstation comprising the Hewlett Packard HP 71 51100 MHz and a CRX graphics monitor was acquired in 1995 together with the LYNX (version 3.09 and version 4.0) Mine Modelling System. Currently the workstation is being used for geological modelling and mine design for the Zerofold at Central Shaft and the Mindola mining at depth project. AutoCAD and Mine Works Planner have been added to the sys- tem configuration. Mine Works Planner is likely to replace Lo- tus123 for mine scheduling tasks. Computer applications in the area of mine planning at Nkana has led to considerable time savings and improved efficiency in areas formerly performed manually and has allowed speedy processing of data that would otherwise have proved too time consuming. Nevertheless, a lot of work still needs to be done in the areas of geostatistics, stope design and financial modelling of mining options. For the foreseeable future computer based planning will operate parallel to manual methods until such a time as sufficient personnel are proficient in the use of computer systems. This paper describes the program of computerization at Nkana Division, reviews current applications and the benefits and experience gained and discusses the promise of current and future developments.

Jan 1, 1996

By P. Songfack

In this work, the slurry flow in the ball mill is solved with Navier-Stokes' equations and the marker and cell technique (MAC), which tracks the fluid-free surface. Considering different planes in the radial and axial directions, this numerical approach leads to the direct calculation of the slurry velocity profile, mill holdup, and volumetric flow in the ball charge and pool. The MAC technique takes as input, the results of a direct three-dimensional simulation of the motion of grinding media, and in turn, provides a detailed knowledge of the hydrodynamics of slurry flow through the porous structure of ball load. This technique is a new approach to the mass transport problem that overcomes the limitations of indirect studies such as residence time analysis and holdup measurements.

Jan 1, 1994

By X. Nie

A new one-step process was developed to completely eliminate iron and directly obtain pure Ni, Co, and Cu chloride catholyte from nickel rich matte by low temperature (400 0c) chlorination roasting of Ni, Co, and Cu with HCl and leaching with water (PH 7). The effects of roasting temperature, time, oxygen potential and HCI addition and leaching temperature, pH, H2S04 addition and residue sulphur on the recovery of metals and purity of leaching solution were investigated. More than 99 % of Ni and Co and 95 % of Cu in the matte was directly extracted into the solution while 99.995 % of Fe remained in the residue. The iron concentration in the leaching solution was less than 3.6 X 10-5 mol/L.

Jan 1, 1994