Search Documents

By K. V. Raj, VASU GANGRADE

Airflow in large-opening stone mines is largely dependent on the natural ventilation due to the large cross- section area of the opening. The openings of such stone mines are typically twice or thrice the size of typical underground coal or metal/nonmetal mines. Due to the influence of natural ventilation, air velocities as well as the static pressure drop in the mines are low. Mines rely on auxiliary fans to ventilate active faces to reduce contaminant exposure to mine workers. The National Institute for Occupational Safety and Health (NIOSH) is conducting research on ventilation of large-opening stone mines to reduce worker exposure to dust and other contaminants such as diesel particulate matter (DPM). In order to reduce worker exposure to dust and DPM, an understanding of the airflow pattern due to auxiliary fans in the mine is needed. Under this research, NIOSH researchers are exploring the computational fluid dynamics (CFD) modeling to understand the airflow behavior in large-opening mines. In this paper, the team is presenting the results from three-dimensional CFD modeling of airflow in a large-opening stone mine and investigating the effect of a fan placement with the movement of trucks.

Feb 1, 2025

By N. I. Jayaraman

Dust scrubbers on continuous miners are steadily gaining in popularity. Recent Bureau of Mines research on scrubbers is reviewed, with emphasis on the following areas: * Development of a new type of water-powered scrubber which can be retrofitted to existing miners. * Comparison of scrubber effectiveness with blowing and exhaust line ventilation. * Improving the quartz dust collection of flooded-bed' panels.

Jan 1, 1989

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By T. Leftwich, G. Faison, K. Pavlich, R. Borden, S. Pavlou

Recent regulatory and policy initiatives under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect in risk reduction requirements for the mining and minerals processing industry. For example, Congress is considering regulating 20 special wastes from the processing of ore and minerals through RCRA Subtitle D and TSCA. The performance of risk analyses and environmental planning at mining projects is often driven by Federal and state regulatory standards. Recent regulatory and policy initiatives by the Environmental Protection Agency under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect on environmental planning and risk reduction programs for mining and minerals processing. Regulatory programs implemented under other Federal laws including the Safe Drinking Water Act, Clean Water Act, and Clean Air Act will also impact industry practices. This paper provides: 1) a brief overview of mining waste and mining waste management, and 2) a description of these regulatory initiatives and a discussion on the impacts of new requirements on environmental and risk reduction programs in the mining industry.

Jan 1, 1992

By Ken Wangerud

The benefits of historic mining to this country have been many, but have come at a cost to the environment that has only begun to be understood over the past twenty years. While estimates vary, it is generally recognized that there are over 200,000 inactive and abandoned hardrock mines, with most of them located in the western U.S. Only a fraction of them are believed to be sources of metal releases with significant adverse environmental effects to the watersheds and receiving streams. State water-quality and natural resource management agencies have noted that hundreds of miles of streams are metal-impacted, and the aggregate effects of these sites within watersheds and drainage basins is poorly understood. Resources for the environmental assessment of abandoned mine land (AML) sites and watersheds have been and continue to be limited. Few hardrock mining states receive substantial reclamation funds under the (coal) Surface Mining Control and Reclamation Act. EPA Region VIII (EPA8) has an estimated 90,000 abandoned mining, milling and smelter sites, mainly in Colorado, Montana, South Dakota, Utah and Wyoming. An estimated 13,000 of the sites may have metal releases causing Clean Water Act and CERCLA non-compliance. Results of inventories by states and federal land managing agencies, indicate it is plausible that only 3,000-4,000 of these sites may be causing significant environmental degradation.

Jan 1, 1999

By Garland R. Dever

Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. Operable thicknesses of high-calcium and high-carbonate limestones suitable for use in cement and lime production, steel manufacture, environmental-control measures, and other special uses are documented in Ordovician and Mississippian formations by analysis of 0.3-meter (foot-by-foot) samples. Active and potential mine and quarry sites afford access to water transportation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the Western Kentucky fluorspar mining district, and late Paleozoic erosional unconformities in northeastern Kentucky.

Jan 1, 1977

By D. R. Willmer, E. J. Haas

As national and international health and safety management system (HSMS) standards are voluntarily accepted or regulated into practice, organizations are making an effort to modify and integrate strategic elements of a connected management system into their daily risk management practices. In high-risk industries such as mining, that effort takes on added importance. The mining industry has long recognized the importance of a more integrated approach to recognizing and responding to sitespecific risks, encouraging the adoption of a risk-based management framework. Recently, the U.S. National Mining Association led the development of an industry-specific HSMS built on the strategic frameworks of ANSI: Z10, OHSAS 18001, The American Chemistry Council’s Responsible Care, and ILO-OSH 2001. All of these standards provide strategic guidance and focus on how to incorporate a plan-do-check-act cycle into the identification, management and evaluation of worksite risks. This paper details an exploratory study into whether practices associated with executing a risk-based management framework are visible through the actions of an organization’s site-level management of health and safety risks. The results of this study show ways that site-level leaders manage day-to-day risk at their operations that can be characterized according to practices associated with a risk-based management framework. Having tangible operational examples of day-to-day risk management can serve as a starting point for evaluating field-level risk assessment efforts and their alignment to overall company efforts at effective risk mitigation through a HSMS or other processes.

Jan 1, 2016

By J. A. King, D. R. Weir, P. C. Robinson

The complex mineralogy of the Porgera resource has a pronounced effect on process selection for the recovery of refractory gold and silver. Intimate association of gold with pyrite necessitates a high degree of sulphur preoxidation to achieve acceptable levels of gold recovery. Acid pressure oxidation has been demonstrated to be the only commercially proven process capable of achieving the required level of pyrite oxidation. Gangue mineralization dictates preconcentration of the sulphides to limit the acid consuming capacity and carbon dioxide generation during oxidation. However, the relationship between concentrate sulphur grade and gold recovery to concentrate ultimately governs the optimum degree of sulphide preconcentration. Minipiloting of the preconcentration and oxidation stages of the Porgera flowsheet are described. The influence of these processes on subsequent recovery of precious metals together with the technical and economic necessity of concentrate pretreatment prior to oxidation are discussed.

Jan 1, 1987

By C. M. Liu

"The Freeport-McMoRan Sierrita Crystal Plant produces Copper (II) Sulfate Pentahydrate (CuSO4·5H2O) through a series of cooling crystallizers. In this process, high supersaturation and unwanted spontaneous nucleation promote fine crystals. Seeding through recycled crystal classification can manipulate the crystal size distribution (CSD) for larger crystals. Proper selection of the crystallizer for seeding can prevent spontaneous nucleation and promote final crystal size. This study shows when seeding temperature is closer to the crystallizer temperature, suspension densities in the crystallizers are promoted and overall CSD shifts to a larger size of crystals. INTRODUCTION Figure 1 shows an overview of the crystallization process. The in-plant feed flow, called Pregnant Mother Liquor (PML), enters the first crystallizer and is subsequently cooled through a series of four crystallizers. Specific temperatures are targeted for each crystallizer to ensure the crystallization process is operating within the metastable zone (MSZ). The discharged flow from crystallizer #5 then enters two cyclones. The overflow from the cyclones contains smaller crystals providing seed crystals for crystallizer #5. The underflow from the cyclones begins the drying process. The overflow from crystallizer #5 enters cyclone #3 for removal of fine crystals and seeding purposes. The underflow from cyclone #3 has the capability to provide seed crystals for crystallizer #1 or crystallizer #2. The overflow leaves the system as Spent Mother Liquor (SML). Undersize crystals dissolve into the PML and return back to crystallizer #1.THEORIES AND METALLURGICAL TESTS Seeding requires an understanding of the crystal size, solution temperature and amount of crystals that enter the crystallizers (1). For the seed crystal size, classified crystal seeds can prevent fine crystals returning back into the system which eventually leads to excessive agglomeration (2). Proper selection of the crystallizer can ensure seeding at an appropriate temperature. Seeding at a temperature much lower or higher than the saturation temperature promotes spontaneous nucleation. Typically, seeding between 4-5°F below the saturation temperature is acceptable (5). A general rule of thumb is to add the seed crystals at the temperature between the solubility curve and the metastable zone. An experiment conducted by Mettler-Toledo AutoChem, Inc. indicates seeding close to the solubility curve rather than the metastable zone promotes a lower supersaturation and nucleation rate but yields a higher growth rate and a greater number of larger crystals (1). The amount of seed crystals can not only change the suspension density but also narrows the width of the MSZ in the crystallizers. An experiment conducted by Jaroslav Nyvlt reports with the crystals absent, the maximum allowable undercooling is 6.3 degrees at a cooling rate, 5°C/hour. With the presence of crystals, it narrows the MSZ width to 2.2 degrees (4). Industrial crystallizers normally operate at suspension densities between 15% and 25% by mass. When suspension densities are lower than 15%, it increases the risk of primary nucleation and the probability of incrustations; on the other hand, if the suspension densities are greater than 25%, it can cause a greater attrition rate and increase the probability of deposits (6). Moreover, operating suspension densities between 15% and 25% are also sufficient to minimize supersaturation rate which promotes crystal growth over nucleation (2, 6)."

Jan 1, 2015

By Muriel S. Robinette

Ground-water contamination from uranium operations could be avoided with proper site analysis techniques. Contamination from tailings disposal sites is carried downgradient within permeable hydrostratigraphic units which can be located and delineated with a combination of drill holes, borehole geophysical logs and surface geophysics. Several case studies are presented to illustrate this application.

Jan 1, 1980

By J.N. Kohmuench

Teeter-bed (i.e., hindered-bed) separators are used throughout the mineral processing industry for both classification and density separation. The high capacity and sizing characteristics of these units make them ideal for feed preparation prior to coarse flotation (+0.100 mm) circuits. Teeter-bed separators are typically easy to control with two basic operating parameters, including fluidization water rate and bed level. However, data show that these two parameters greatly interact with one another. Given this finding, a high-level automatic control scheme was developed and implemented on a full-scale separator. In addition, dialogue with plant operators has led to several simple changes to an already established design that improves operational and maintenance characteristics.

Jan 1, 2010

By John L. Shafer

A process for the conversion of stibnite (Sb2Sj) concentrates, crude antimony oxide, or metal to a pure cubic antimonous oxide (senarmontite) has been developed on a laboratory scale. The conversion of stibnite to senarmontite has been piloted. The high purity of the final product is the result of forming antimony trichloride as a low temperature distillable intermediate. To obtain the antimony trichloride the stibnite, or crude oxide is slurried in molten antimony trichloride and reacted with gaseous hydrogen chloride. Antimony metal is oxidized to the trichloride with chlorine. The hydrogen sulfide produced from the hydro- chlorination of stibnite can be upgraded to a strength of 95% or greater for further treatment. The crude antimony trichloride is separated from the gangue by a preliminary evaporation and then is fractionally distilled and the trichloride distillate has less than 50ppm of arsenic and lead combined (the most troublesome impurities in antimony processing). The purified antimony trichloride is then hydrolyzed with sodium or ammonium hydroxide to produce the cubic form of antimonous oxide (senarmontite) to the exclusion of the rhombic form (valentinite) which is photosensitive. The advantage of this process is the ability to treat a wide range of antimony ores, concentrates, and metal to yield a high purity oxide in a controllable range of particle sizes.

Jan 1, 1975

By Guy T. Jr. McBride

World food production is not matching the exploding increase in world-population. Since arable land is limited, ways are being sought to increase yields by turning_ to fertilizer. Phosphate, an essential fertilizer ingredient, is undergoing a period of growth unparalleled in history. The United States is at once the world&apos;s largest producer of food and of phosphate rock. Both food and fertilizer output in the United States are being enlarged to meet the demands posed by the threatening world food crisis. New phosphate deposits are being developed in Florida and North Carolina to assure the United States&apos; continued preeminence in this vital resource. Large fertilizer complexes are also being constructed with an eye to both domestic and foreign markets. The growth of the U. S. phosphate industry has been characterized by developing technology in the processing and distribution of phosphate raw materials. The trend from low analysis to high analysis materials accompanied by a change from a large number of small fertilizer plants oriented toward the marketplace to a fewer number of large plants located at the raw material source is illustrative. These changes in technology and distribution have also been important factors in the development of new mining areas in Florida, the Western States and North Carolina.

Jan 1, 1966

By J. R. Patts, L. D. Patts, S. J. Janisko, T. Barone

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more efficient and effective use of rock dust. A prototype, flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed in line between the ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over a period of three days at set distances from the fan exhaust to assess the changes in float coal dust levels in the return due to the operation of the scrubber. Mass-based measurements were collected on a per-cut basis and were normalized per foot of advance by the continuous miner. Results show that average float coal dust levels measured under baseline conditions were reduced by over 91% when operating the scrubber. INTRODUCTION In 2012, underground mining in the United States produced over 342 million tons of coal [EIA 2013]. During the cutting, crushing, and transport of this coal, dust is generated and can be entrained in the air ventilating the mine. Title 30 Code of Federal Regulations Part 75.400-1 (30 CFR§ 75.400-1) defines float coal dust as particles of coal that can pass a No. 200 sieve. These coal particles can be carried by the ventilating air into return entries before settling onto mine surfaces [NIOSH 2006]. If this float coal dust becomes re-entrained into the airstream, it can propagate an explosion throughout mine workings [Harris et al. 2010]. Application of rock dust in underground coal mines is required by Federal regulation as a means of preventing the propagation of explosions by float coal dust. In order to meet Title 30 Code of Federal Regulations Part 75.403 (30 CFR § 75.403), 80% incombustible content must be maintained in the composition of dust deposited in mine entries [76 Fed. Reg. 35968 (2011)]. This fraction of incombustible content is increased if elevated levels of methane are present. In order to maintain the required incombustible content, frequent or constant application of rock dust is undertaken by mine operators. Title 30 Code of Federal Regulations Part 75.2 (30 CFR § 75.2) defines the properties of the rock dust that must be used by mine operators."

Jan 1, 2015

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

By Jeffrey C. Wynn

Since the early 1970&apos;s, the U.S. Geological Survey (USGS) has carried out exploration geophysical research on non-basemetal strategic mineral commodities, including uranium, lithium, gold, potash, and chromite. The chromite study (largely completed) and the potash study (still going on) carried out during the past 4 years have not been aimed at the discovery of new ore reserves, but instead were designed to complement exploration by private mining companies. The USGS has carried out research not normally conducted by these companies, but which can be used by them in their efforts to increase production of strategic minerals. Results of the chromite and potash studies highlight the importance of: 1) a laboratory-research phase (petrophysical and petrographic studies) at the beginning of work on any new commodity; 2) an operative or functional ore-deposition model to serve as a conceptual framework, and the necessity to continually test, refine, and modify it during the study; 3) indirect geologic/geochemical indicators, secondary associations, and the use of multiple physical properties; and 4) the use of a systematic inverse-cost sequential-exploration (i.e. lowest resolution and lowest cost first) strategy to keen the exploration economically reasonable. The keystone to the success of the study is frequent and substantive dialogue among geologists, geophysicists, and geochemists.

Jan 1, 1981

By Nicola Beltrandi, Andrea Pigorini, Holad Mohamed Dahir, Ezio Pedone

"Genoa is a very distinctive city located between mountains and the sea and infrastructural upgrading works often have to deal with the intersection of existing infrastructures. This is the case for the new railway tunnel construction between the stations of Brignole and Principe which under-cross two existing double-track tunnels in operation. The latter have been constructed with masonry bricks and the vertical distance between old and new tunnels is approximately 1m. Due to rock characteristics and the urban environment, stability and vibrations control are the main issues. Consolidation work with the fore-poling method and a specific sequence of excavation, primary lining and final lining support have been designed to assure stability and settlement control. A hard rock road-header has been used to assure vibration control. Finally, a real time monitoring has been implemented. The article presents monitoring and back-analysis results of the under-crossing of the existing tunnels. GENERAL LAYOUT OF WORKS The Genoa railway junction constitutes an integral part of the Ventimiglia-Genoa-Novara-Milan railway line route and it is included amongst the railway systems of the Tyrrhenian-Northern European multi-modal corridor (corridor of the two seas or corridor VII Genoa-Rotterdam). The main aims of the project concern the upgrading of the existing lines and the separation of the long-distance passenger and freight traffic flows from those of a regional and metropolitan type. The project includes: •,Completion of the connection with the port of Genoa Voltri and the Italy-France coastal route. •,Interconnection with the future Terzo Valico dei Giovi mountain pass route towards Milan. •,Upgrading of the Genoa Voltri – Genoa Brignole main line to four/six tracks. Rearrangement of the systems at the Genoa Voltri, Genoa Sampierdarena and Genoa Brignole Stations, reorganisation of the services in the Genoa Terralba area and interchangeability with the metropolitan system complete the design activities. The contract which includes civil and technology works is divided into four construction lots (ref. Figure 1):"

Jan 1, 2016

By T. M. Yegulalp

A numerical model is being developed to assess the enhancement of permeability by improved fracture connectivity by micro-hydrofracturing. A generic two-dimensional percolation model has been developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals&apos; Mineral Park Mine has been used to establish statistical properties of the observed fracture systems. Results of statistical anlyses of the field data and examples of the use of percolation model are presented.

Jan 1, 1995

By Richard Seal

Nabarlek is situated in the Arnhem Land Aboriginal Reserve about 270 km due east of Darwin in the Northern Territory of Australia. During the dry season (May to November) Nabarlek is accessible from Darwin over the Arnhem Highway-- a distance of 330 km. Throughout the wet season (December to April), except for a few days, access is provided by aircraft from Darwin to the Nabarlek airstrip. Because of the limited access during the wet season, reagents and supplies have to be stock- piled for six months on the site to maintain operations. With the mine and plant being remotely located on private Arnhem land with very limited access outside the site fence, operating personnel are flown to Darwin every six days for their days off.

Jan 1, 1980