Search Documents

By T. B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores and, for major veins, their great vertical range (>990m). Less well-documented are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine, and volcaniclastic rocks deposited within the diatreme complex. The ore-gangue minerals Here precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate, and oxide minerals along with minor base metal sulfide and precious metal telluride-s. Wallrock alteration is quite limited adjacent to veins and somewhat more extensive within hydrothermal and tectonic breccias.

Jan 1, 1991

By Robert Kimutis, Heather Dougherty, Eric Watkins

Gas wells have often intersected mining resources, but unconventional shale well drilling has more recently challenged mines to balance the risk of interaction due to higher pressures and larger quantities of gas. Full extraction mining, such as the longwall method, induces ground movement that may influence the casings if wells are drilled within the mining area. The possibility of a casing shear would lead to the risk of unplanned gas migration into the mine. This has the potential to quickly overcome the ventilation system and reach the explosive range which, if ignited, can have catastrophic consequences on the health and safety of underground workers. The utilization of network software to model mine ventilation is a common practice in the mining industry as a predictive tool for planning and monitoring and can assist with a well breach scenario over a large mining area. This work focuses on a well breach in between two longwall panels after second panel mining with gas entering primarily through the gobs of the adjacent longwall panels. Applying the network software Ventsim, a gob zone and ventilation network were created to better understand the distribution of gas within the mine and the limitations and effectiveness of a ventilation system. The model shows both a transient flow simulation and steady state concentrations throughout the mine ventilation system. Using a standard Pittsburgh coal seam longwall ventilation scheme, we find that the system can dilute a significant inflow of up to 700 cfm of methane.

Oct 12, 2023

By Gary H. Higgins

The paper by Lewis and Braun l presents experimental and calculational evidence that primary chalcopyrite ores are rapidly oxidized by warm oxygen-bearing water. Resulting solutions contained copper sulfate products of the matrix rock decomposition such as magnesium sulfate and sulphuric acid. Iron was oxidized to insoluble hematite and hydrous iron sulfates. Oxygen injection near the base of a broken and permeable flooded ore deposit was calculated to cause circulation of oxidizing solutions to the entire permeable region. The rate of dissolution of copper and degree of oxygen saturation for given oxygen injection rates were presented. Their work suggests that in-situ recovery of deep, disseminate primary copper deposits is technically feasible. The actual feasibility depends on economics and environmental safety as well, and it is the purpose of this paper to address these two aspects.

Jan 1, 1972

By A. Palit, M. K. Mohanty

This investigation has concentrated on optimizing the newly developed Pansep linear screen and developing empirical models to predict the screening performance. Most empirical models developed in the past to predict the performance for industrial screens are suitable for the vibratory screens. Understandably, these models are deficient in predicting the performance of linear screens due to the difference in their operating principle. Thus, the main objective of this study has been to develop empirical models suitable for linear screens to predict the partition coefficient for a given size fraction as a function of the aperture size. The inadequacy of the conventional model equation originally developed for vibratory screen has been demonstrated and a modified equation developed to predict the partition coefficient as a function of the normalized mean particle size (d/d50c). In addition, new model equations have been developed for linear screens to predict the screening efficiency as a function of the separation size(d50) and to predict the separation size as a function of the screen aperture. It is believed that these model equations will be useful for the plant operators in selecting the mesh panels of correct aperture size and in predicting the product size distribution based on the selected aperture size.

Jan 1, 2003

By Timothy C. Richmond

The Stillwater District is located in south central Montana approximately 75 miles southwest of Billings, the state's largest city. It lies along the northeast front of the Beartooth Mountains and is within the boundaries of the Custer and Gelatin National Forests. The district contains some of the nation's most spectacular mountain scenery. Montana's highest peaks, including 12,799 foot Granite Peak, rise a few miles south of the area. Much of the district is located on a gently undulating plateau which averages 8500 ft. above sea level, broken by hills up to 10,000 feet and slashed by glacially carved canyons, some of which are more than 3,000 feet deep.(Fig. 1) Immediately to the north and east, the land falls away to the Great Plains, stretching unbroken to the Mississippi River. Two major tributaries of the Yellowstone River, the Stillwater and Boulder Rivers, traverse the area and several large streams originate in the district itself. Access to the high mountain country and the adjoining Beartooth Primitive Area is restricted to a few horse and jeep trails continuing from the terminus of improved roads in the bottom of the Stillwater and Boulder Valleys. Hunters, fishermen and cabin owners make intensive use of the area along its improved transportation routes, but hikers seldom venture more than three miles beyond the end of the roads. People from the Billings area are the most frequent visitors.

Jan 1, 1974

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By J. G. Nalven

On July 1, 1999, most domestic metal mines will have to report releases of toxic chemicals into the environment for the first time as required by SARA Title 313. Some of these reportable releases will appear huge in relation to reports by other industries. The reasons for the potentially large reportable releases, special considerations for mining operations, and strategies for dealing with the reports are described. Data composited from experience with several mining companies is presented in the context of a typical gold mine.

Jan 1, 1999

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By W. L. Hollinshead

For more effective and cost saving production in tunnels, the machinery used on construction sites will be equipped with guidance systems combined with working procedure management systems. This paper describes sensors for these systems and various system configurations. A project is described which uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 1999

By Liam Findlay

Optimizing a production schedule with semi-mobile in-pit crushing & conveyance (IPCC) requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout, and truck fleet investment decisions. An integrated stochastic optimization framework is proposed to produce long-term schedules for mining complexes using multiple semi-mobile IPCC systems. The optimizer selects the crusher locations and designs the conveyor routes from anywhere in the mines. The stochastic framework considers simulated multi-element orebody realizations and manages associated risk. A hybrid metaheuristic based on simulated annealing and evolutionary algorithm is implemented for the optimization. The method is demonstrated using an iron ore mining complex.

Jun 25, 2023

By D. T. Kirkwood

The practice of impounding mine water and liquid fine waste in underground mines is increasing. Often these underground impoundments are created by constructing seals or bulkheads designed to withstand the expected hydraulic pressures. Occasionally seals are built for another purpose, usually to act as explosion-resistant ventilation barriers. Due to factors such as clogged drain pipes or unexpectedly high inflow rates, these explosion-resistant seals sometimes become subjected to hydraulic pressures. The incidence of seal failures due to inadequate design and/or construction is also on the increase. Fortunately, to date, no lives have been lost by water seal failures, but a clearer understanding of the design and construction considerations specific to water seals is vital to keep this from occurring in the future. This paper presents technical considerations for the design and construction of seals which will specifically be required to withstand hydraulic pressures in underground mines.

Jan 1, 1995

By J. Scheepers, P. Smith, G. (Yunfei) Qiao

High pressure acid leach (HPAL) and pressure oxidation (POx) or pressure leaching extraction processes occur in autoclave vessels operating at elevated temperature and pressure, acidic conditions with abrasive mineral slurries. The harsh process conditions require specialized severe service metal seated ball valves to support operation of the vessels. Over several decades thermally sprayed titanium dioxide (TiO2) and chrome oxide (Cr2O3) coatings have been applied to extend the service life of the ball valves and other high wear critical components. Variability in the coating application quality control and severe process conditions can result in spalling, coating failure and premature failure of the component resulting is decreased autoclave circuit availability. In 2012 MOGAS, together with BRENCO, initiated research and development for ML-381, metallurgically bonded coating. This paper includes the historical development of severe service ball valve coatings, success of the trials and increasing industry adoption of the ML-381 coating for ball valves and other critical autoclave circuit components.

Mar 2, 2022

By Yong Yuan, Wenhao Xiao, Luc Taerwe

"The static shear stiffness of an immersion joint subjected to combined compression and shear forces is investigated by experiments in a test set-up. To explore the performance of the immersion joint, the compression-shear loads, which are applied on a specimen according to test protocol, are determined based on real design situation. In this test, the main focus is on the steel shear keys and the rubber sealing. For the applied loading schemes, different levels of axial force, corresponding to the water depth of the joint, are considered as well as the changing amplitudes of the shear force. The force-displacement curve is obtained and the hysteresis is observed during the whole test. The joint‘s static shear stiffness is calculated, showing to increase linearly with respect to the magnitude of the axial force. Moreover, it is found that the rubber sealing has a significant influence on the shear behavior of the joint. INTRODUCTION An immersion joint is the connecting part between two adjacent elements of an immersed tunnel. Compared to that of the bulk elements, the stiffness of the immersion joint is relatively small. When it is subjected to shear actions, whether resulting from vertical foundation settlement or horizontal earthquake movements, shear-resistance of the joint is the main concern for a safe and reliable water-proof design. A flexible immersion joint, which normally consists of a rubber seal and shear keys installed at an element end is a common solution in practice. The way in which the shear keys and the rubber seal behave in the joint together is of vital importance to a comprehensive understanding of the shear behavior of the joint. However, in literature very few experiments on the shear behavior of immersed joints are available although the flexible joints are applied in practice for more than 50 years already. O. Kiyomiya (2004) carried out both a 3-dimensional experiment and a finite element analysis for a new type of flexible joint referred to as the Crown Seal. The results indicated that this new type of joint can be applied in practice because of the effective reduction of lateral deformation. A linear model was found in the paper of Anastasopoulos et al. (2007) to describe the behavior of the shear keys, which consider that the stiffness of the shear keys tends to infinity. R.S. van Oorsouw (2008) discussed the shear capacity of concrete shear keys in segmental joints, by analyzing the influences of reinforcement and friction force between shear keys."

Jan 1, 2016

By R. D. Cook, J. L. Johnson

"Measuring mud bed level in a sedimentation device is an important control variable. Methods used to date for this purpose have had limited success providing continuous, consistent measurements at a reasonable price. This paper describes a new instrument for detecting the mud bed / liquor interface as well as bed density profiles. The state of the bed is measured directly with sensors located in the thickener. Data from bench-scale and full-scale tests show that the bed level is well defined and easily detected. In addition, full-scale testing revealed unprecedented information about thickener beds. Variation in bed density gave new insight into thickener bed dynamics, providing design and control opportunities never before possible. This novel instrument can significantly improve thickener control by providing reliable and consistent bed level measurements. It is also capable of measuring bed density profiles that can potentially identify significant operating problems early enough to take corrective action before experiencing costly shut downs. INTRODUCTION Numerous studies and papers have been devoted to the subject of thickener design and operation to achieve specified throughput and discharge densities. Mathematical models have been developed that present methods for sizing thickeners and predicting performance under varying process conditions. The compression effect of deeper beds on dewatering performance is a recognized phenomenon (Wilhelm and Naide 1981). This is one variable of many that are inter-related and influence thickener performance. For example in the steady-state, continuous operation of a thickener, if the solids feed rate increases and the bed level remains the same, the underflow discharge rate must increase with the result of solids concentration being lower. The interactions of these parameters are at the heart of thickener models. One such model (Burger and Narvaez 2007), predicts solids concentration profiles increasing downward and discontinuities between settling zones. This model uses sediment height (bed level) as a parameter that influences capacity calculations to achieve the specified solids concentration of the underflow. Knowing the bed depth is critical to maintaining stable thickener operation. Implicit in these modeling strategies are some basic assumptions such as homogeneous distribution of solids in the different settling zones, plug flow of solids through the settling zones and steady state operation of the thickener. The accuracy of these assumptions has not been verified because there has been little visibility inside the bed of full size operating thickeners. Testing of the instrument presented in this paper demonstrates that it provides a degree of visibility of the dynamics in a thickener not previously possible and indicates that the basic assumptions of the modeling strategies may not be completely accurate."

Jan 1, 2015

By Irwan Halim, Stephane Polycarpe, Brian Hann

The Narragansett Bay Commission Phase III CSO Program includes construction of the 11,600-foot long, 30-foot ID, deep rock Pawtucket Tunnel in Rhode Island. This paper provides an overview of the Design Build Project features and highlight some of the important design considerations, features, and innovations, including geologic conditions and related TBM design, and deep shaft and tunnel segment designs. The paper provides the most recent updates on some of the project construction activities including TBM tunnel progress and retrieval schemes, tunnel pump station and deep vertical shaft liner installations, SEM construction, and microtunneling for the longest adit using Fiberglass Reinforced Polymer Mortar pipes.

Jun 23, 2024

"Controlling dust generation and keeping it below permissible limits at the working face of a room and pillar mine is a challenge for mine operators. With the recent changes in the respirable-dust regulation, it has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) stated that a flooded-bed scrubber, under its optimum condition, can achieve cleaning efficiencies between 58 and 90 percent. The performance of such a system can be maintenance intensive. Other industries face similar dust control issues. The University of Kentucky partnered with Toyota Motor Manufacturing for the development of a novel wet scrubber for capturing paint overspray, with capture efficiencies in excess of 98 percent and minimal maintenance. The aim of this study is to assess the ability of this novel wet scrubber to capture respirable dust in an underground coal mine. This paper presents the conceptual design and the computational fluid dynamics (CFD) modeling of this novel wet scrubber. It discusses the results of the CFD simulation performed on the novel wet dust scrubber. INTRODUCTION Dust generation from underground coal mining is an inescapable phenomenon. No matter the practices employed, it inevitably occurs. Elevated concentrations of coal dust are potential health and safety hazards. Although dust in an underground coal mine cannot be completely avoided, its influence can be mitigated through good engineering practices. The effect of dust on the health of mining personnel has had a significant impact. The prolonged exposure of airborne respirable dust (< 5 µm) can cause coal workers’ pneumoconiosis (CWP), silicosis, emphysema, and chronic bronchitis, collectively known as black lung (U.S. Department of Labor, 2014). According to the National Institute for Occupational Safety and Health, black lung has killed more than 10,000 miners between 1995 and 2004 (NIOSH, 2008). In addition to being a health issue, coal dust is also a safety issue to the underground coal miners. The generated dust, if not captured, is dispersed into the mine air through the ventilating air and deposited downwind on the return entries’ surfaces. In the event of a methane explosion, the coal dust, if insufficiently diluted with rock dust, triggers a coal dust explosion which is much more severe than a methane explosion and causes more damage (Kenneth et al, 2006). The Jim Walters No. 5 Mine and the Upper Big Branch Mine disasters which together killed 42 people and resulted in damage worth millions of dollars in property are the examples of coal dust explosions (U.S. Department of Labor, 2001 & 2010)."

Jan 1, 2016

By L. K. Lepley

A marine sonic sub-bottom profiling system and a hovercraft were used in an engineering geophysics survey of the tailings being deposited at the Mercur gold mine. Detailed density sections with vertical resolution of one meter were desired for computations of strength, permeability and potential self-compaction. The logistical problems of conducting a geophysical survey and in collection of geotechnical soil samples from an active tailing impoundment was solved by using the amphibious hovercraft for towing and transport on the impoundment. The "chirp" sonic system produced continuous, real-time geophysical cross-sections with vertical resolution of ten centimeters showing possible trapped gas. The hovercraft provided a platform over water, ice, slurry, and solid beach for collection of geotechnical information and physical samples.

Jan 1, 1994

By Christopher Newman, David Newman

The ability to assess, address, and predict mining-induced stress distribution is paramount in maintaining a safe and efficient underground operation as coal mines continue to develop at deeper depths and in more geologically complex reserves. This is especially true for longwall mining operations given their limited flexibility in panel layout and orientation. This paper focuses on ground behaviors and conditions observed at two deep-cover, steeply dipping longwall mining operations in Utah’s Unita coal basin. This region is susceptible to coal pillar bump/bounce events as a result of high depth of cover, high-extraction mining, and the close proximity of a thick massive stiff sandstone stratum to active mineworks. The successful prediction of mining-induced coal bump events for Mine A and Mine B operating in the Unita basin has prompted mine management to develop a rock mechanics testing database for reserve calculations. The database is applicable to mine planning as well as the development of multiple numerical models to proactively identify and address adverse ground conditions using input parameters calibrated to site-specific behaviors and conditions. For both Mine A and Mine B, the most critical question relates to longwall development and recovery for “extreme” deep-cover longwall panels at overburden depths greater than 600 m. This paper highlights the impact of high-stress concentrations associated with deep-cover longwall mining as well as the methods applied to mitigate stress impacts on miner safety and longwall production.

Jul 1, 2023

By Karoly (Charles) Kocsis, Jeff Johnson, Felipe Calizaya, Tulio Dias, Natanna Nunes

Two pressure balancing chambers were constructed at a Colorado coal mine to reduce the risk of spontaneous combustion. Each chamber was established by installing a Kennedy stopping at about 10 ft (3 m) in front of an isolation seal, and equipped with two safety doors, a nitrogen injection system, and a set of environmental monitors. Several pressure balancing tests for different ventilation conditions were conducted in these chambers. During each test, pressurized nitrogen was injected into the chamber and the pressure differentials across the stoppings and seals monitored. This study presents a summary of the results achieved, lessons learned, and the basic requirements to operate a pressure chamber effectively.

Feb 1, 2024

By Rodrigo Estay Huidobro, Andrés Martinoli, Claudia Pavez-Orrego

The effects of induced seismicity caused by mining activities are one of the main problems that the mining industry faces. Although it has been documented by countries with a great mining tradition (United States, Canada, Australia and Chile) for over a century, the problem has been intensified throughout the years due to the greater depths that mineral extraction reaches, where the stress levels and environmental conditions increase the possibility of a rockburst occurrence. Seismic events inside the mine cause important losses of human lives and infrastructure damage. To deal with this problem it is necessary to implement several kinds of safety protocols. For example, seismic indicators allow to identify, through the analysis of a set of seismic parameters -magnitude, energy, time, decay rate, among others-, periods of time when a seismic event of considerable magnitude is most likely to occur. The objective of this work is to use the frictional energy generated by a microearthquake inside the mine as a seismic indicator, linking it with the occurrence of large magnitude seismic events which are outer the background activity. Thus, we seek to determine the set of seismic parameters which allow the best performance of the frictional energy/heat indicator. In the present study, we considered magnitude, frictional energy, and time as seismic parameters to study the efficiency of the proposed indicator. The optimal set of parameters was determined using two different methodologies: accumulated thermal energy and alert bands. The Piece Skill Score and the Accuracy indexes were used to evaluate each set of parameters. Both approaches show a high rate of true positive and true negative hits. Furthermore, it was concluded that both methods show complementary results in terms of the detection of critical events (Mw > 3.0).

Apr 26, 2022