Search Documents

By D. C. Panigrahi

The paper presents the development of a thermodynamic based network analysis model. It uses transient heat flow algorithm for computing the heat flow from strata and predicts the environmental condition in different branches of the network. Along with the environmental condition, the mass flow distribution in network is computed by using nodal pressure method based on linear theory approach. The algorithm has been coded using object oriented programming approach and it has been validated in actual field condition. The correlation is satisfactory.

Jan 1, 1997

By Gordon R. Wicker, John A. Cole

Although the evaluation of autoclave oxidation for Getchell ore was begun nearly 40 years ago, its ultimate implementation in 1989 represents the first substantial improvement in the economics of processing this refractory ore. Sulfide ores at Getchell were previously roasted prior to leaching (in the 30's and 60's), resulting in somewhat lower recoveries than are currently realized by autoclave oxidation. Recoveries on the order of 90% are expected from the high-arsenic sulfide ore over the expected 10-year mine life.

Jan 1, 1990

By Eduard Hamm

The main reasons for the development of higher heat levels in German coal mines are the increasing depth of working with the con- sequent higher rock temperatures, increased use of electrical equipment, and increasing coal output due to concentration and mechanisation of workings. In place of the normal decentralised underground cooling plants, schemes and pilot plants have been developed to produce the required cooling capacities in central air cooling units, which then supply the cold air to the underground working points where needed.

Jan 1, 1980

By L. Max Scott

[INTRODUCTION] The significance of gamma exposure to uranium miners has been recognized only in the last few years. Most ore deposits which have been underground mined, were 1% or less U308. Full-time mining of this grade ore can result in exposure exceeding 1 Rem per year. Several companies in Saskatchewan are planning to mine recently discovered ore bodies which contain ore pods in excess of 10% U308. The purpose of this paper is to present dose data which can be used to estimate gamma exposure from high-grade ore deposits, and to present mining techniques which will minimize miner exposure. [Dose Estimates] When one has a point source of radiation, the conventional laws of isotropic emission and the fall of dose with square of the distance, make dose calculations relatively easy. However, if one has an area source of infinite thickness, the assumption must be made that a uniform gamma flux is being emitted from all faces of the source (Figure 1). Dose from gamma emission would fall off only due to air attenuation up to such a distance at which the source can be considered to be a point source (usually 10 times the largest dimension of the source). For short distances, such as to the cab of ore-moving equipment, the dose reduction would be negligible. Assumptions: 1) Radium and gamma-emitting daughters are in secular equilibrium with uranium. 2) All gamma radiation is emitted from radium and its daughters. 3) Average gamma energy of 0.8 MeV. 4) Uranium ore has a linear attenuation coefficient of 0.212 cm-1, similar to that of Si02(sand). 5) Uranium ore density of 3.0 gm/cm3. 6) One curie of radium emits 6.84 x 1010 photon/sec(l). 7) One percent uranium ore contains 1 x 10-8 Ci/cm3 of radium. 8) Each MeV of 0.8 MeV photon results in a dose of 2.10[ ]10-3 mRem/hr. per MeV/cm2 -sec. 1) 9) Minimum ore depth 100 cm. 10) Linear attenuation coefficient instant for radium gamma of 0.374 cm -1 [ ] The photon flux from a radioactive slab is computed as follows: [Flux = photon/cm3 3(1) 2u S] [where, us is the linear absorption coefficient of s the source (uranium ore).] Thus, 1% uranium ore, in the form of an infinite slab, emits 1613 photon/cm2-sec, which results in a dose rate of 2.71 mRem/hr. Since the dose from an infinite slab is the same as a dose from an infinite radius right circular cylinder, the only correction needed from the above dose rate is for finite radius and point of dose above the end of the cylinder (Figure 2) [Dose = mRem/hr. {E2(bl) - E2(b3) - [(E2(b1sec[E] -E2(b3sec[E]]cos[O](1)]

Jan 1, 1981

By D. L. Sober, D. Ince, T. V. Vasudevan

Separation of dolomite from Florida phosphates was achieved by first conditioning the feed with fatty acid at pH 10 followed by reconditioning at pH 4 or below, before flotation. Observed selectivity of this two-stage conditioning process was attributed to the amount as well as changes in the nature of adsorbed collector species upon reconditioning. In this paper, bench-scale flotation results of optimizing the major process parameters, such as reconditioning pH and collector dosage, for upgrading natural high dolomitic phosphate samples from Florida are discussed.

Jan 1, 1991

Machine breakdowns and maintenance delays are large contributors to lost production and increased operating costs in the mining industry. The US Bureau of Mines is investigating the applications of expert system technology to diagnostic and predictive maintenance for mining equipment. This will help increase mining productivity and decrease operating costs by reducing the frequency of equipment failures and repair times. The Bureau has begun this effort by applying expert system techniques to the diagnosis of hydraulic system problems on a continuous mining machine. This paper discusses the development of the hydraulic diagnostic expert system.

Jan 1, 1992

By G. Mbuyi Kamba, J. Patigny, E. Jacques

Traverse anemometry is still widely used today. In this paper an investigation of the influence of three factors which are believed to contribute to the resulting error of the method, is reported. They are the shape of the traversing path, the size of the vane anemometers and the air velocity pattern. These factors are experimentally studied on a test facility developed specially for this purpose. Taking into account the results of 576 measurement sessions, as well as published information, some preliminary conclusions are drawn, and additional questions are raised.

Jan 1, 1993

By T. Seal

The Hydro-Jex technology has been used by Newmont Mining Corp. on the gold heap leach pads on the Carlin Trend - Nevada for three years to recover the inventory gold and change the chemistry in the pads. This research and development patented process is complete with the resultant data presented. Information on drill sampling, geophysical surveying, followed by leach pad stimulation with impacts on solution chemistry and gold recovery are discussed. Can this technology be used to rinse and close heap leach pads faster with reduced pump energy costs and improved recovery?

Jan 1, 2007

By K. Osseo-Asare

Metal recovery from solution, i.e., the formation of a solid product from a purified aqueous electrolyte solution, is increasingly becoming more than a simple matter of bulk precipitation. In many cases, operating conditions must be carefully manipulated to control the rate and yield of the precipitation/crystallization process, as well as the purity and physical characteristics of the solid product. A review is presented of the underlying physico-chemical processes, with emphasis on solution and interfacial chemistry. Opportunities for the integration of hydrometallurgical metal recovery and materials processing operations are discussed.

Jan 1, 1989

By D. R. Spears, C. E. Jordan

In an effort to improve flotation efficiency of the domestic minerals industry, the US Bureau of Mines conducted research to measure the improvement provided by fine bubbles on the flotation of fine-sized particles (minus 20- µm, minus 625 mesh). The turbulent velocity distributions of the fluid within the flotation cell were measured as a function of time and position and used to increase the precision of a fine-particle, turbulent-flotation model. For the mineral system tested, improved flotation response was obtained in the laboratory testing with small bubbles and intense agitation. These results matched the model's predicted response.

Jan 1, 1991

By Lisa Shevenell

Three pits at the Getchell Mine contained water during a hiatus in mining activity (1968-1983). For this period, expected concentrations of As, C1, SO4 and TDS resulting solely 16om evaporative concentration were computed. Computed values are 1.6 to 2.3 times greater than those measured in local groundwaters. However, computed values fix As, SO4 and TDS are lower than measured values in the pit lakes. In some cases, the computed values are only 8% of the measured pit lake values, indicating a major control on water quality via water-rock interactions. In contrast, computed C1 values exceed measured pit lake concentrations.

Jan 1, 2000

By Y. T. Auck, M. E. Kukura, L. G. Stevens

At its Technical Development Center in Tucson, Arizona, the UOP Mineral Sciences Division operates a completely integrated pilot plant testing a proprietary process for the extraction of nickel from limonite/saprolite ores. The process is based on the reductive roast- ammonia leach procedure now employed in several plants around the world. The process improvements are such that nickel extractions well above that experienced in these processes are possible, particularly on the more garnieritic/saprolitic ores. This paper will describe the process and the results of process development studies. The data show that pilot plant results confirm those obtained on the smaller laboratory and bench scales of experimentation.

Jan 1, 1979

By Aladar B. Dory

INTRODUCTION Anyone familiar with the problems of hardrock mining will agree that the majority of the serious dangers present in mining are quite visible and obvious to any person reasonably familiar with the profession. Having unsecured, unscaled back over ones head, gives one a very good chance of ending up under a caved in mass of rock. Staying too close to a blast gives one almost a certainty of being hit by a flying rock. Too little oxygen in the air will very quickly lead to loss of consciousness and death. One walks only so much over deep, unsecured openings before he falls into them. It is because of this clear visibility of the conventional health and safety hazards that mining regulations in almost all jurisdictions world-wide are a more or less comprehensive collection of "shalls" and "must nots" of good common sense. When basic rules of common sense safe working practices are at stake, there is little room for dialogue and compromise. The mine inspector is then observing, during his inspection, how well the mine follows these common sense rules. RADIATION AS A HIDDEN DANGER Radiation in mines is a risk, the impact of which does not demonstrate itself immediately. It is first of all a potential risk. Two individuals exposed to identical radiation will almost certainly be effected differently, if at all. This is certainly true of exposures and doses one might encounter in the mines today. We hear very often the phrase: "there is very little known about the effects of radiation". It is one of the most misused and misunderstood half-true statements. I would doubt that there is any other carcinogen whose effects have been studied as extensively as the health effects of radiation. Where the statement is correct is regarding the knowledge of the quantitative assessment of the risk of low level radiation exposures. The reason for this uncertainty is that the magnitude of their health effect is very close to the health effects of natural radiation, cosmic radiation and the effects of other carcinogens such as industrial pollution, hydrocarbons from cars and other chemicals we have grown accustomed to using. As far as lung cancer is concerned, the effects of wide use of tobacco probably outperforms any other single substance. All this having been said, the bottom line is still unchanged. Radiation exposure, in most cases mainly radon daughter exposure, was and still is one of the health hazards of uranium mining and as such has to be controlled to the best of our ability. Various jurisdictions have adopted different approaches to the control of radiation exposures of uranium minemill workers. The following sections of this presentation will attempt to explain the regulatory approach taken in Canada. THE CANADIAN REGULATORY PHILOSOPHY As indicated earlier, the health effects of low level radiation are quantitatively not yet defined and no proven threshold of radiation exposure exists. The Atomic Energy Control Board's (the Board's) regulatory system is based on the basic assumption that there is no absolutely safe limit of radiation exposure below which there are no health effects. Theoretically we should therefore strive to reach zero exposure. It is obvious that this objective cannot be reached in real life. The objective of the regulatory process therefore has to be to achieve radiation exposures of the workers that are as low as reasonably achievable, social and economic factors taken into account. This, of course, is the internationally acclaimed ALARA principle put forward by the International Commission on Radiological Protection (ICRP). To avoid any misunderstanding it is worth emphasizing that the ALARA principle is applied to achieve exposures below the regulatory limits which must not be exceeded in normal operation of any nuclear facility including uranium mines and mills. The present regulatory limits for radiation exposures of atomic radiation workers are based on the recommendations of the ICRP and they are almost universally accepted. They should ensure that the risk from radiation exposure is not greater than the risk associated with working in a comparatively safe industry. Basically, there could be two extreme approaches to the regulation of uranium mining and milling. One extreme approach is to develop very extensive and detailed regulations and requirements covering all aspects of radiation protection. This is a somewhat autocratic approach to the regulatory process. This approach has two very serious shortcomings. If detailed requirements are set in regulations, due to the great variations of actual conditions at various mine-mill facilities, they have to be set as a compromise between the desirable requirements and those which could be met by practically all facilities. This approach takes away from the management of the facilities the initiative to strive for improved conditions. Requirements are spelled out in clear, understandable targets and the only worry of the management is to comply with these targets. One of the basic duties of management is to manage the operations in the most effective way with the maximum health and safety of the workers in mind.

Jan 1, 1981

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By M. H. Al-Dabbagh

In this paper, the authors outline the deficiencies of PERT/CPM as a method for scheduling complex projects such as mine development. In particular, PERT/CPM networks cannot accommodate logical nodes (events) or stochastic branches (activities). The Graphical Evaluation and Review Technique (GERT), developed by Pritsker and. co-workers, is introduced as an alternative to PERT/CPM that overcomes many of the deficiencies of the latter and enables a more realistic analysis of complex projects that are subject to significant uncertainties. A brief overview of GERT network structures and network analysis is given and a PC implementation of the method is described. The technique is illustrated by application to the development of an open-pit gold mine in Saudi Arabia.

Jan 1, 2002

By M. Sheppard, P. Wand, G. A. Cooper, M. Lesage

The vibrations generated by a tricone drill bit are caused by the successive impacts of the bit teeth on the rock, and peaks in the vibration spectrum can be associated with impacts coming from particular rows of teeth on one or other of the bit cones. Wear of the bit teeth causes a shift of these peaks to higher frequencies at constant bit rotary speed, whereas changes in rock type generally produce changes in peak height. Bit bearing failure or poor hole-bottom cleaning both cause loss of definition in the spectrum, the latter often associated with spurious high-amplitude signals at low frequency. The vibration signals may also be analysed in the time domain, where, for example, cone locking can be identified by characteristic features in the signal of torsional acceleration.

Jan 1, 1987

By William E. Cobb

15.1 INTRODUCTION The mine development process, as discussed in Chapter 2, is a series of data gathering and analysis steps. As the mine development process proceeds, information about the geology, mineability, and metallurgy of a particular deposit is continually generated, along with environmental information regarding project permitting status. As data are obtained, checkpoint evaluations are typically conducted to determine the economic viability of the particular deposit. Although the project evaluation process was discussed at length in Chapter 2, a brief review of the process is presented here to "set the stage" for the discussion on economic analysis of heap leach projects. Figure 15.1 (MacKenzie, 1980) presents an overview of the sequential process of mine development. Once the deposit is discovered or acquired, an initial delineation program can be undertaken to expand the project's geologic, mining, and metallurgical data base. At the end of this initial program, the direction of the project is evaluated. The company can either abandon the project, postpone it, develop and mine it, or gather additional data in hopes of improving the project's economic viability. If the company continues gathering data, then another decision point and evaluation will be required. This process may continue until the company either decides to postpone the project or develop and mine it. A project may be postponed indefinitely, typically in hopes of improved metals prices. Certain holding costs, such as land or royalty payments, may be associated with postponement. In general, once a company goes through two evaluations, the project is less likely to be abandoned. For this discussion, it is assumed that the company will undertake initial, second, and third delineation programs to gather sufficient geologic, mining, metallurgical , and environmental data to justify a positive production decision from the second or third economic evaluation. The objectives of the first delineation program will be to confirm and expand upon the available information about the deposit. During the second delineation program, development funds should be directed toward identifying the critical project items (i .e., ore reserves, mineralogy, mineable grade, metallurgical recovery, etc.) that must be resolved before making the production decision. This second economic evaluation can be used to determine which metallurgical concept will be applied to the project: heap leach or a traditional agitation-type leach plant. If the proper work has solved key project concerns in the second program, a production decision may be made from that evaluation.

Jan 1, 1988

By George C. Carter

It was just a little over three years ago that the "Go" button was pushed to start operations on the blending piles at Oro Grande. As is usual with any new installation, there were problems that had to be solved. This paper will concern itself with those problems directly related to quality control. To obtain a consistent outgoing quality level at the most economical level for a finished product requires two main points: 1. Measurement of variations in the process, 2. A method of making a predictable change to adjust for variations. The manufacture of cement requires a relatively high degree of accuracy if a consistent outgoing quality level is to be maintained. The blending piles were our solution to this problem.

Jan 1, 1962

By S. K. Kawatra

Various types of mathematical descriptions of the flotation process are used in the design of a full scale flotation circuit. Mechanistic descriptions developed under controlled laboratory conditions establish theoretical residence time requirements. Empirical models, describing flotation performance as a function of full scale operating variables, are established from one flotation system and applied to another hypothetical system. Problems of design by mechanistic modeling, such as scale up factors, can be alleviated if the model is developed from a full scale flotation circuit. However, the numerous uncontrollable variables encountered in a full scale operation would preclude the practical application of such a model. Incorporating empirical relations into the full scale mechanistic model will facilitate its effective use as a guide for flotation circuit design. A semi-empirical model has been developed that promises to offer a more effective means of flotation circuit design.

Jan 1, 1982

By S. R. S. Sastri, D. K. Senguta, S. K. Bhaumik, G. V. Rao

The amenability of a calcite-bearing ore to the reduction of silica to below 0.2% by physical beneficiation was studied. The objective was to use the ore as a raw material for seawater magnesia production. The ore contains complex gangue minerals such as diopside, forsterite, phlogopite, clinohumite, graphite and quartz. These contribute to around 25% acid insolubles with 6% SiO2. Reverse-flotation studies using various cationic collectors with tannin as a depressant indicated the possibility of reducing the acid insolubles to around 5%. Direct flotation of calcite with anionic sodium oleate in the presence of sodium silicate and lactic acid as a depressant indicated the possibility of reducing the acid insolubles to below 3% and the SiO2 to from 0.2% to 0.3%. Lactic acid was found to be an effective depressant of the complex gangue minerals in the ore.

Jan 1, 2000