Search Documents

By L. B. Kirk, A. R. Kirk

At New World, Au-Cu-Ag mineralization occurs in stratiform car-bonate-hosted, massive sulfide-iron oxide, and skarn-replacement deposits. Regional pyritic-alteration, local massive sulfide mineralization and mine wastes generate acid drainage within the district. Water quality improves down gradient through dilution and mixing of acid and metal-rich mine water with bicarbonate-rich, low-metal surface and groundwater, and precipitation of metal-rich ferrihydroxide phases. Natural deposits of ferricrete indicate that pre-mining ARD has occurred, providing important clues to pre-mining water quality. The geoenvironmental model identifies the Cu-skarn mineralization as the primary target for ARD management. Closure success will be limited by the geoenvironmental nature of the natural mineralization.

Jan 1, 2004

By Michael Jatczak, Joseph A. Sopko

Ground Freezing was used for excavation support and groundwater control of a 12.8m (42-foot) diameter, 61m (200-foot) deep drop shaft for the South Bay Ocean Outfall Tunnel in San Diego, California. Approximately half way through the excavation, excessive groundwater inflows from the base of the shaft resulted in suspension of excavation and evaluation of the frozen earth wall. This paper discusses the forensic methods used to identify the zone where groundwater intrusion occurred and the methods associated with evaluating zones of high groundwater velocity. The use of remedial grouting and localized liquid nitrogen injection are discussed and evaluated. Concepts of frozen shaft design are discussed, including a new method for permitting the launch of the Tunnel Boring Machine through the frozen earth wall and associated freeze pipes.

Jan 1, 1999

By Rainer Alles, Markus Keller

INTRODUCTION For overland conveyors of several kilometres length and as well as wide for conveyors designed for high mass flows, the cost for the conveyor belting share is 40% to 50% of the invested cost 173. The German Standard DIN 22101 is used for calculation and dimensioning of - conveyor belts and belt conveyor components. Developments in rubber technology and conveyor belt design required a revision of the standard released in 1982 121, which was published in August 2001 131. New research results and publications 16-9, 13-15] led to a better understanding of the material behaviour and their influences on conveyor belts. Test and calculation methods have been established to determine the most important parameters which are related to the performance of a conveyor belt line. These parameters are • The running resistance of the idlers • The indentation resistance of the belt • The dynamic splice efficiency • The distribution of belt load in the splices, transition zones and on pulleys. As a result, new rubber compounds with low indentation losses allow the use of reduced friction coefficients and thus lead to reduced power consumption, smaller drives and lower belt tensions. The deeper understanding of the flux of forces within belt splices led to both optimised splice design and optimised rubber compounds which significantly improve the dynamic splice efficiency. Therefore, in accordance with the standard, the benefits of these technologies and the better understanding of material behaviour allow a reduction of belt strength still maintaining sufficient safety factors. Thus engineers are enabled to calculate belt tensions more exactly and users are encouraged to pay more attention to starting and braking techniques. DETERMINATION OF DRIVE FORCE According to the DIN standards the resistance to motion generally has to be determined for each different section of the belt conveyor including upper and lower run separately. The necessary drive power P is calculated as [ ] with v as the conveying speed. The total of all resistances to motion of carry and return run can be determined as [ ] FHo and FHu are the primary resistances consisting of the running resistances of the idlers, the indentation resistance of the belt, the fulling of the conveyed material and the flexure of the belt. While indentation resistance and idler resistance are measurable, they have been deter- mined to be responsible for up to 70% of the primary resistances covered by FH. Further FN is the secondary resistance that covers, for example, the resistance of feeding points and scrapers. Fa are the total slope resistances and Fs is the total of all special resistances, resulting, for example, from belt steering devices. These three resistances should be neglected in the following discussion. For conveyors where a determination of the substantial parts of the resistances to motion is not possible, according to the new DIN standard [31 a determination of the drive power is acceptable by using the fictitious friction factor) [ ] In this formula the index i identifies the individual section of the conveyor, 1 is the length of the section and MR, MG and ML are the related masses of the idlers, the belt and the load in kg/m. The fictitious friction factor f determines the ratio between the overall resistance to motion and the total of moved masses within the

Jan 1, 2004

By Anthony R. Przybylek, John M. Visnesky

INTRODUCTION Thermal dryers have been utilized for reducing moisture of bituminous coal since the late 1930's. Since that time, numerous changes in the coal industry have motivated advances in thermal drying technology. The purpose of this paper is to discuss the changes that occurred to dryer design and focus on current practices of fine coal drying. The major topics discussed in this paper are: - Early Thermal Dryer Design and Evolution - Current Drying System Design and Associated Components - Current Economics of Fine Coal Thermal Drying - Future Markets and Design Considerations EARLY THERMAL DRYER DESIGN AND EVOLUTION Background The practice of drying fine coal with heated air has been performed for more than one half century. Throughout that period, both Metallurgical and Steam coal producers have used this method for reducing the surf ace moisture content of their fine plant products. During the late 1930's and early 19401s, vibrating bed and flash dryers were used to per- form the drying duties. Closed water circuits and vacuum filtration had not yet been integrated into process circuitry and centrifugal dryers were in their early stages of development. During that same period, changes in mining practices were reshaping the distribution of coal to our processing facilities. Plants originally designed for the purpose of processing coarser fractions of coal were being burdened with additional quantities of fine coal. Those plants, unable to recover fine coal, would reject these solids to plant bleed. The higher incidences of stream pollution that resulted from these events prompted clean stream legislation and the need for new, more efficient fine coal recovery circuits. The coal processing industry responded to these needs by integrating closed water circuits and filtration into circuits. The fine coal filter cakes recovered exhibited poor handling characteristics by themselves and often required further dewatering to improve their characteristics. Flash dryers at that time were being used to dry the coarser products. For those facilities operating flash dryers, the solution to this new problem appeared to be simple. The filter cake was combined with the coarser (-1/4") coal and then introduced to the flash drying column for drying. The filter cakes, however, presented significant problems for the flash drying systems. Heavy lumps of filter cake could not be dispersed and conveyed by the rising hot air and as a result would settle out in the bottom of the column. This material, known as "drop-out", would then accumulate and require further handling. The solution to this problem was not an easy one. Sophisticated mixing equipment was employed to condition the feed to the dryers. As attempts to minimize drop-out with this approach failed, the only recourse was to collect the material with conveying systems and recycle it back to the plant or dispose of it. The additional costs of handling this material reduced the attractiveness of the flash systems and opened the door for the development of a new, more cost effective coal drying system. Due to the nature of the problems experienced by the flash systems, fluid bed systems were considered. Fluid bed dryers were being used in other industries at that time but had no operating history in the coal industry. Dorr-Oliver transferred technology from other industries and built the first fluid bed drying system for fine coal.

Jan 1, 1988

By David Martin Menne, Chris Campbell-Hicks

Optimisation of many oxide gold processing facilities, in most cases, either does not really take place or if it does take place it happens too late or takes too long. This is unf01tunate as extra profits and early cash flows are lost, in new projects, and/or may not be realised at all in others. The situation is easily avoid­ed by ensuring that the plant optimisation happens immediately following commissioning or for an established operation simply 'biting the bullet' and making it happen immediately as a 'better late than never' decision. This type of optimisation requires intense undiluted focus on each and every problem or restriction that contributes to reduced plant performance or bottlenecks, without letting go, until the predetermined outcome is produced. Thus a dedicated person with specific quantative goals is required for these tasks. Methodology and strategies for optimi­sation are discussed and numerous examples presented. The secret of successful heap leaching is discussed.

Jan 1, 1998

By N. Rowlands

The importance of mineralogical and chemical characterization of fine particles in the fields of mineral and metallurgical processing is discussed. Emphasis is placed on electron beam analysis techniques including electron diffraction and energy dispersive analysis with special reference to the scanning trans- mission electron microscope. The correct choice of instrument depending upon particle size, composition and nature of sample is stressed and the analytica1 capabilities of different types of instruments are evaluated. Recent applications of electron beam equipment to processing problems are presented and the paper concludes with a review of new developments in the fields of surface analysis and micro-diffraction.

Jan 1, 1985

By R. W. Barbaro, R. V. Ramani

Generally, production planning is concerned with the best use of fixed resources to determine a production schedule for one or more production units supplying one or more markets. Production scheduling determines when each production unit will be used and its production level. However, the production scheduling problems are intimately associated with the location of existing or new production units and processing facilities. Normally, mine location allows only a limited choice; processing plant types and locations are considerably more flexible. This paper presents a generalized multiperiod MIP model as an aid in determining the mine production schedule and the processing plant types and location to satisfy multiple markets. A brief description of MIP and how it has been applied in the mineral and other industries is discussed. A complete description of the model with an application to a coal preparation plant system is presented.

Jan 1, 1987

By James L. Whitlock, Amy E. James

During the past twenty years, numerous advances have been made in the technologies used to pretreat sulfidic refractory gold ores. These advances have included improved equipment design, increased gold recoveries, and reduced operating and capital costs. More recently, treatment of refractory gold ores has primarily been accomplished by pressure oxidation (POX), roasting, chlorine oxidation, or biooxidation. In addition to improving the time-proven processes of pressure oxidation and roasting, new and innovative approaches to biooxidation pretreatment of both concentrates and whole ores have been developed. Selecting the appropriate biooxidation technology depends on the nature of the refractoriness in the ore, economic gold recovery, plant design operating parameters (such as desired tonnage), site climatic conditions, and operating and capital costs, as well as several other deciding factors. The objective of this paper is to outline the biooxidation processes and technologies currently available for the recovery of gold from refractory sulfidic ores, to discuss the critical factors that affect plant design and operation, and to provide the metallurgist with a practical guide to choosing the appropriate biooxidation technology for a particular ore or concentrate.

Jan 1, 1999

By T. B. Jarboe, H. Wen

Introduction The 150 MW circulating fluidized bed (CFB) power plant described in this article is the product of recent Bechtel experience in the industrial power and steam market, where the economic feasibility of fluidized bed projects has been proven. The ability of CFB boilers to burn low grade fuels makes it possible to burn low ranking coals or coal wastes. These include anthracite culm, coal mine rejects, and coal wash-plant-waste slurries. This article also addresses the impact of fuel characteristics on plant design. This includes solids handling, steam generation, sulfur capture, and auxiliary load requirements. The uncertain economic environment in which utilities must now operate has shifted the industry's interest away from large, base-loaded generating units to small, more versatile installations. Utilities now consider purchasing new generating capacity in smaller increments and staging its deployment to correspond with demand increases. In this way, they lower their risk in the increasingly hazardous art of long-range load forecasting. This strategy has many advantages. Multiple, smaller units have inherently greater turndown capability and better availability than a single larger unit of the same size. In addition, the smaller units will each have better cycling capability. And, with CFB combustion, the smaller units will have greater fuel flexibility. General plant description The 150 MW powerplant described here is a grassroots CFB unit. Fluidized bed technology differs from conventional combustion techniques. With CFB, solid fuel, together with inert material such as sand, gypsum, limestone, or ash from the fuel, is kept suspended in the combustion chamber. This is done by using the action of the fluidizing air distributed below the bed. Fluidization promotes the turbulent mixing conditions required for good combustion. The turbulence causes the entire mass of solids to behave like a liquid. The result is improved mixing. This allows heat to be generated at a lower and more uniformly distributed temperature that is below the ash fusion temperature of most coals. The fluidizing mechanism offers several other advantages over conventional combustion. There is less volatilization of alkali compounds, which cause deposits on boiler tube surfaces. And there is less sensitivity to the quantity and nature of the ash in the fuel. The low combustion temperatures prevent vitrification of the ash particles and minimize problems associated with furnace slagging. The ability to select from many fuels is one of the major advantages of CFB combustor technology. Fuels that can be burned in CFB plants to produce steam and electricity include: low grade coals with high ash or sulfur, lignite, peat, wood and pulp products, biomass, refuse, anthracite culm, petroleum coke, and oil shales. The plant's turbine cycle uses superheated steam at 12.4 MPa (1800 psi) and 538°C (1000°F), with single reheat to 538°C (1000°F). Two high pressure and three low pressure, closed, feedwater heaters are furnished. So is a deaerator, which is an open, direct-contact heater. The CFB plant exceeds EPA's New Source Performance Standards (NSPS) for air emissions. The design limits sulfur dioxide (SO,) emissions to 0.25 kg/GJ (0.6 lb per million Btu). SO2 reduction occurs in the combustor by reac-

Jan 11, 1988

By L. A. Pursell

The case history, which is the subject of this paper, involves the expansion of a lime plant in Texas. The major new production unit is to be a 545.45 tonne per day coal fired rotary kiln. Auxiliary facilities include additional quarry haulage equipment, modifications to the crushing plant, a hydrator, storage facilities, and a loading system. The existing plant consists of a high calcium limestone quarry, two coal fired rotary and 10 gas fired shaft kilns, nth crushing, screening, stockpiling, hydrating, storing and loading facilities. The proposed modification would increase quarry volume from 545,000 tonnes per year to 805,000 tonnes per year. The plan also includes the addition of dolomitic lime to the product line which requires the purchase and handling of 186,000 tonnes of screened, washed dolomite yearly. A decision to undertake such an expansion was previously a simple and straight forward process. Such a decision now faces a major and complicating obstacle which can delay the project, raise the expected cost, or prevent it entirely.

Jan 1, 1980

By Michel Grenier, Mahendra Gangal

Two methods used to measure the exposure of mine workers to diesel exhaust particulate were compared. One method was developed by the U.S. Bureau of Mines and the University of Minnesota's Particle Technology Laboratory. The method which was originally developed for use in coal mines is a size selective sampling technique. The other method uses an “ashing" approach to assess the exposure to diesel particulate. This second method is based on the principles of sampling according to the ACGIH respirable dust sampling criteria and the use of a silver membrane filter as collection substrate. Because a silver membrane filter is used, both respirable combustible dust (diesel particulate) and respirable silica can be measured from one sample. The comparison study took place in a Canadian lead-zinc mine during tests which were primarily designed to evaluate the gaseous and particulate emissions characteristics of new diesel engine technology. The study has shown that under the test conditions encountered, some differences were observed between the results as obtained by the two methods. These differences seem to depend on the characteristics of the respirable dust found in the work- place, i.e., size and composition. The impact, on sampling and analysis of diesel particulate, of the proposed guideline (ACGIH) for a TLV® of 0.15 mq/m3 is discussed briefly.

Jan 1, 1997

By I. Iwasaki

There are many reasons why the US mineral and primary metals industry is in its present state. Undoubtedly, a flood of imported goods in all sectors is playing a major role in the plight of our raw materials industry. Domestic industry is becoming increasingly aware of the importance of its international competitiveness. And we are beginning to wonder what is happening to our technological edge. A number of factors affect the international competitiveness. Engineers cannot do much about some of these factors - labor costs, tax policy, government relations, interest rates, dollar strength, and labor-management relations. Something can be done about technology, however. Some say technology is so easily transferable today. But I would like to believe that we have the ability to apply it better than others. Not too many years ago, "made in Japan" meant cheap and shoddy products. Today, Japan has completely changed its image. The US is beginning to feel the threat from Japan's low-cost, defect-free products with dependable delivery. With worldwide recession and the strength of the dollar, we were shocked at the sudden weakness that developed in America's industries, not only in the international market, but domestically as well. What went wrong and what can we do about it? Senior executives from 300 large American manufacturing companies were surveyed. These executives believe US companies must: • invest in more efficient plants and equipment (27%); • invest in more research and development (23%); • improve the quality of service to customers (23%); and • adopt more aggressive marketing tactics and strategies (14%). Are we not doing enough research? The US has nearly four times as many people engaged in research and spends four times as much for research as Japan (Fig. 1). There is little doubt about the excellence of the US performance in basic science as indicated by the number of Nobel prize recipients. Japan has produced only four winners since World War II. Look at technology trade of five countries (Fig. 2). Again, US performance has been remarkable. An interesting observation here, is that the United Kingdom, another country with economic woes, is also in the black, West Germany and Japan, both with trade surpluses, are net technology importers. It is apparent that the US' performance in the commercialization of new knowledge is much more in question. Japan had $50 billion of trade surpluses with the US last year, which led to some friction between Washington, DC and Tokyo. Comparing the technology trade of Japan and the US in more detail, Japan imports disproportionately large amounts of technology from the US and Europe. This data is rather old, 1978, but the general trend is not too different even today. It is generally believed that scientific research leads to innovative technology, then to economic payoff. But, after seeing the current technological challenge by Japan, we are forced to change this traditional view. Investment in research may eventually lead to economic payoff, but not directly. There is a middle ground between new knowledge and its commercialization. This is an area where the Japanese have been successful. Until the 1970s, many western companies licensed patents to Japan for quick profits. But, in recent years, these companies have become more discrete about the terms of technological transfer. As a result, a number of scientists and engineers are expressing deep concern over the future of technological developments in Japan. A survey was conducted on 450 research managers of private industries in Japan on how they viewed the level of breakthroughtype original research in Japan as

Jan 6, 1986

By R. L. Grayson

As a followup to a USBM-sponsored research project, the authors utilized the knowledge-base structure and system concepts from a Sun Sparcstation-based worker-scheduling system of the mine-management support system to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, including their availability and work priorities during a shift. The system can optimally allocate manpower on a work shift and can delineate supervisory training responsibilities. The various components of the software, including enhancements made to the original system, are described in detail.

Jan 1, 1997

By James A. Morrison, Stephane Carayol, Paul H. Madsen

The Rio Piedras Alignment Section 7 of the Tren Urbano is currently being constructed beneath a historic commercial section of San Juan. Different portions of the section are being constructed using open cut, cut-and-cover, New Austrian Tunneling Method (NATM), Earth Pressure Balance Machine (EPBM), and as tacked drift mined support system. The combination of complex geology, low ground cover, and several innovative construction methods present many challenges to the ground control program. Mining and construction sequences were first developed to minimize ground movements and risk of damage to structures. A unique compensation-grouting program was developed to improve the ground, limit settlement, and recover settlements incurred due to mining.

Jan 1, 1999

By Viacheslav Lyakhov, Cornelis H. Iestra, Victor I. Beloborodov, Vitaliy Bogdanovich

The results of a study and effective use of flotation for processing of ores with complex mineral composition containing fine-disseminated minerals with high specific density are presented in the paper. The object of research was complex baddeleyite-containing ore from Kovdor deposit (The Kola peninsula, Russia). Baddeleyite is a valuable, rare mineral, natural Zirconium dioxide with 5.8 - 6.0g / cm density, grade content 0.15 - 0.17 and dissemination less than 0.2 mm. The authors carried out a thorough investigation of baddeleyite- containing products selected in different sites of gravity flowsheet. It was determined that due to similar specific weight some sulphide minerals (pyrite, pyrrhotite) come into concentrate together with baddeleyite and, also, minerals of pyrochlores group (hatchettolite). The results obtained revealed the possibility of use the flotation for retreating rough baddeleyite concentrate. he given gravity concentrate has a number of specific features, e. g. high density of its minerals which, in its turn, provides for high speed of sedimentation of solid phase in pulp, and for the presence of large amount of sulphide minerals (up to 10%) having good flotability. With these features being taken into account a technology for flotation of baddeleyite-containing products after their preliminary gravity concentration has been developed (up to 5 - 10% Zirconium dioxide). The technology has three flotation stages. At the first one the reverse flotation of baddeleyite is carried out during which "light" minerals (forsterite. apatite and carbonites) come into froth product and at the second one flotation of sulphide minerals and at the third one direct flotation of baddeleyite is performed from the underflow product. The following reagents were used for flotation: of phosphate type (sodium tripolyphosphate, mono and diethers of alkylphosphpric acid) and sodium xanthate as collector for sulphides. The given set reagents provides for high effectiveness of flotation due to selective of collectors and presence of froth layer with high carrying ability. New flotation technology of recovering of baddeleyite from complex ore was developed and applied at the Kovdor Mining Plant, using AKER flotation machines.

Jan 1, 1995

By D. H. Desy

This research was undertaken to establish the lncendivity of aluminum alloys against rusty steel under frictional impact conditions at typical coal mine fan speeds, to determine any differences in incendivity among various aluminum alloys, and to Investigate less incendive materials as substitutes for aluminum alloys. With a specially designed apparatus, three aluminum casting alloys and three constructional steels were tested for incendivity in frictional impact against rusted steel in flammable methane-air mixtures. Although varying in degree, all aluminum alloys investigated exhibited a high ignition probability under the test conditions; none of the steel specimens tested caused any ignitions under the same conditions.

Jan 1, 1973

By J. Reyher, R. Bratton, G. Luttrell, B. Li

"Flotation is regarded as the best available method of upgrading minerals and coal fines. However, its efficiency deteriorates rapidly with decreasing particle size. Further, ultrafine concentrates are difficult to be dewatered economically, forcing companies to discard part of the ultrafine materials to impoundments. To overcome these problems, a new method of separating and simultaneously dewatering ultrafine particles has been developed. Following extensive laboratory-scale test work, the process, known as hydrophobic-hydrophilic separation (HHS), has been tested successfully in continuous operations at proof-of-concept (POC)- and pilot-scale tests. The results show that the HHS process is capable of producing high quality clean coal with high recoveries and low moistures. INTRODUCTION Coal preparation plants are designed with up to four parallel processing circuits for treating coarse (> 12 mm), intermediate (12x1 mm) small (1x0.15 mm), and fine (<0.15 mm) particles. The plus 0.15 mm fractions can be effectively cleaned efficiently with gravity separation methods (Wills, 2006). At present, the only commercially viable option for cleaning the finest fraction is froth flotation (Yoon et al., 1999). In flotation, air is dispersed in the form of small air bubbles in a tank in which coal fines are suspended. The small air bubbles selectively collect the hydrophobic coal particles and float to the surface, forming a froth phase which overflows into a launder. As is well known, ultrafine coal particles of less than 30-50 µm are difficult to be collected by the air bubbles, resulting in low recoveries. Furthermore, fine particle flotation suffers from low carrying capacities and poor selectivity due to entrainment problems. (Bethell et al., 2005; Luttrell et al., 2014). In addition, the froth products containing ultrafine coal are difficult to dewater. Mechanical dewatering in general becomes inefficient with decreasing particle size due to small cake porosity and high surface area, resulting in high moistures (Hucko et al., 1988). The cost often becomes prohibitive with particles of smaller than ~45 µm (Bethell et al., 2005). Moreover, the high-moisture products are difficult to handle and incur high shipping costs and lower thermal efficiencies (Honaker et al., 2013)"

Jan 1, 2016

By Chris Crowl

Employee involvement does not directly correlate to performance improvement. A key ingredient is the introduction of new Human Resource Systems that promote both performance improvement and employee involvement. Many organizations have tried to use employee involvement as the &apos;&apos;fixer" of performance issues-and seen their performance deteriorate further. They failed to realize that the entire human resource strategy must be connected to the goals of performance improvement and that greater employee involvement is only one tool in that strategy. So what are Human Resource Systems? These are systems that all managers use to get work done. Most of us are familiar with basics such as planning, assigning work, checking progress (auditing), completing assignments. We also commonly think in terms of staffing, training, compensation, or corrective action. All of these are human resource systems. All must be designed to support what you are trying to accomplish with your people. We call that the Human Resource Strategy. Let&apos;s examine one part of a total strategy intended to support more employee involvement at Kennecott Utah Copper-the hourly job structure. The design of hourly jobs directly affects how many employees of different capabilities are required to get the work done. It begins to answer some fundamental questions: • What are the roles and accountabilities of each employee? Do they have enough information to make decisions, to take responsibility for their work?

Jan 1, 2004

By D. L. Kowal, P. J. Whittaker, M. A. Tuzun, N. O. Lotter

The area of flotation testing of drill-core is important in the business plan of most mining companies. Metallurgical information derived from this practice can be used to advantage in strategic decision-making. Sampling, flotation testing and subsequent Qem SCAN analysis of a mineral resource is one example of this approach. Anew resource, located in Sudbury, Ontario, is being assessed for the Sudbury Operations of Falconbridge Limited, which includes the Strathcona Mill. In this case, it was possible to improve the value of information from sampling and flotation testwork by using an improved, statistically-based test design, by sampling the resource by generic end-member ore type, and by integrating the Mineral Processing and Mineral Science disciplines into a Process Mineralogy team. In addition to producing standard metal grade and recovery information, this new approach provides more reproducible information from representative samples and flotation testing in a replicate format. Qem SCAN technology is used to produce a size by size mineral balance, including both modal percentages and liberation, from which flotation models for each ore type can be developed. As a result, a key understanding of the potential behaviour of a given ore type, if mined and then processed at the current mill operation, is gained at the 95%confidence level. The three ore types of this mineral resource were shown to have different flotation characteristics. Quantifying the mineralogy and liberation in each of the three ore types, has shown that this difference is due to changes in modal percentages of ferro-magnesium and magnesium silicate minerals such as pyroxene, talc and serpentine. Liberation across the three ore types is very similar and is therefore not responsible for variation in flotation performance.

Jan 1, 2003

By L. Reyes-Bozo, R. Ginocchio, A. Godoy-Faúndez, C. Sáez

Relationships among mining industry, society and environment have been historically complex due to its environmental impacts. In the Chilean mining industry, repetitive and small spills of fuel during maintenance of machinery have been adsorbed by desert soils and sawdust to control environmental pollution. The froth flotation is the main technology to recover specific mineralogical species from sulphide ores. Flotation reagents are expensive and representing an environmental risks due to its physics properties. Our objective was to investigate the feasibility of applying bioremediation as a cost-effective alternative technology to physical-chemical treatments and to evaluate the efficacy of biosolids as foaming agents. Our results show that the bioremediation is feasible by use of the autochthonous microbial communities and biosolids could be used as new environmental-friendly organic reagents. This research discloses a sustainable bioremediation process and industrial ecology model based on these two successful cases.

Jan 1, 2011