Search Documents

By J. G. Groppo, T. L. Robl, C. J. McCormick, W. M. Lewis

The combination of froth flotation and hydraulic classification can facilitate the production of a high-quality pozzolan that meets or exceeds ASTM specifications. This combination has been rigorously evaluated and results of pilot-scale testing are presented. Pilot-scale testing was conducted on fly ash from two active electric utility storage ponds. The tests demonstrated that a high-quality and consistent pozzolan could be produced using Advanced Pozzolan Technologies' Fast Float™ Process. Along with the pozzolan, the additional production of aggregate for masonry mortar and the production of a low sulfur, medium-Btu fuel were also demonstrated. The Fast Float™ Process incorporates several simple unit processes to ensure pozzolan consistency. Classification controls the particle size distribution, which is critical for achieving early strength;flotation controls the grade with respect to L.O.I.; and dewatering controls the moisture content.

Jan 1, 2000

By R. W. Smith, K. A. Altman

The use of activated alumina for the removal of selenium from heap leach detoxification solutions was studied at a laboratory scale. Three different aluminas were studied, one unmodified and two chemically modified to function better in a basic pH range. The best performer, Discovery Chemicals DD-6, readily accumulated selenium oxyanions. Furthermore, it could be stripped of selenium and several metals by a mild caustic solution (pH 11.5 – 12.0) and regenerated for further use. Tests using - 600 µm, + 300 µm (28 x 48 mesh) material indicated that 96 % could be removed from solution and using – 1.18mm, + 600 µm (14 x 28 mesh) material 91 % could be removed. However, soluble silica can accumulate on the activated alumina and subsequently interfere with its regeneration and should be removed from the detox solution prior to use of the adsorbent.

Jan 1, 2003

By Anthony D. Hammond, Charles A. Kliche

A slope stability study for the Annie Creek and Foley Ridge Mines was undertaken to provide Wharf Resources, Inc. with a technical assessment of the stability of the slope for an overall pit slope angle of 60°. A rock analysis of the most critical and persistent combination of discontinuities was carried out using probabilistic methods. A detailed discontinuity mapping and assessment of the rock mass provided the orientation data used in this study. The orientation data were reduced and analyzed to identify the discontinuity sets. A statistical analysis provided information about the distribution of the data. A deterministic wedge stability analysis identified the critical combination of discontinuities; those with a low factor of safety were further studied using probabilistic kinematic and kinetic stability analyses. The results from this approach were used to obtain the reliability or probability of failure of the slopes.

Jan 1, 1988

By John G. Viets, J. Robert Clark

A multielement extraction system is being used successfully to provide essentially interference-free geochemical analyses to aid in gold exploration. The Methyl isobutyl ketone-Amine synerGistic Iodide Complex (MAGIC) extraction system separates Ag, As, Au, Bi, Cd, Cu, Ga, Hg, In, Mo, Pb, Pd, Pt, Sb, Se, Sn, Te, T1, and Zn from interfering geological matrices. Quantitative extraction of these elements is accomplished over a broad range of acid normality, making it possible to economically determine all 19 elements from a single digestion or leach solution. The resulting organic extracts are amenable to analysis by inductively coupled plasma atomic emission spectroscopy (ICP-AES) and flame atomic absorption spectroscopy (FAAS). For many years the principal shortcoming of ICP-AES was the complex spectral and stray-light interferences that were caused by the extreme variability of components such as Fe. Na, and Ca in common geological matrices. The MAGIC extraction allows determination of the extracted elements with enhanced sensitivity, from a virtually uniform matrix, by ICP-AES and FAAS. Because of its simultaneous multichannel capabilities, ICP-AES is the ideal instrumental technique for determining these 19 extracted elements. Ultratrace (sub-part-per-billion) determinations of Au and many of the other extracted elements can be made by graphite furnace atomic absorption spectroscopy (GFAAS), following back stripping of the extracts. The combination of the extraction followed by stripping of the organic phase eliminates 99.999% of potential interferences for Au. Gold determination by GFAAS from these extracts under the specified conditions yields a fourfold improvement in sensitivity over conventional GFAAS methods. This sensitivity enhancement and the interference-free matrix allow highly reliable determinations well into the parts-per-trillion range.

Jan 1, 1990

By Richard D. Grove

The on-stream analysis of phosphorus and silica has not been possible by XRF techniques and only recently has some success been indicated with quantitative XRD for P. Yet there has been a recognized need for an on-stream analysis of P and acid insoluble to permit the automatic control of phosphate rock flotation plants which produce some 30-40 million tons of concentrate each year in the southeastern U.S. IMC Fertilizer, Inc., the largest U.S. phosphate rock producer, embarked on a program to develop such an on-stream analysis capability several years ago. Following many months of lab and prototype development, the first commercial installations started in December 1986 and now have completed some 400,000 analyses with surprising accuracy, precision and reliability. The use of these devices in the improved control of the phosphate flotation plant is currently receiving some very serious attention at IMC.

Jan 1, 1989

By E. P. Chen

This investigation involves the development of a two-dimensional continuum model for the description of jointed media. Specific application of the model developed here is for the potential geological disposal of radioactive waste in the layered sequence of fractured volcanic tuffs under Yucca Mountain, Nevada. This is currently being considered by the Nevada Nuclear Waste Storage Investigations Project, administered by the Nevada Operations Office of the U. S. Department of Energy. The work is a direct extension of the previous constitutive model by Thomas (1982) based on the work of Morland (1974). The main feature of Thomas's model includes two parts: a continuum approximation based on average discontinuous displacements across jointing planes within a representative elementary volume, and a material constitutive description based on linear elastic matrix material behavior and nonlinear normal and shear joint behavior between jointing planes. The mathematical descriptions by Morland based on strain partitioning among matrix material and joint sets allow multiple joint sets to be included in the model. However, the initial effort by Thomas to implement Morland's mathematical model included only a single set of joints. To make the material model reflect more realistically the field characteristics, the current work extended Thomas's model to include orthogonal sets of joints. The nonlinear elastic normal joint behavior is retained in the present model. Joint shear response was treated as linear elastic in the shear stress versus shear displacement relationship prior to attaining the stress level governed by the Coulomb friction criterion. Beyond this critical stress value, a horizontal line is assumed in the work of Thomas for the shear stress versus slip displacement relationship such that the shear stress remains constant while the slip displacement increases. Motivated by experimental observation, the current work generalized the shear response to allow a line with finite slope to govern the slip behavior beyond the critical stress level. The inclusion of an orthogonal joint set led to a fourth order algebraic equation for the calculation of stress increments as compared with a second order equation obtained by Thomas. The nonlinear elastic normal joint behavior provides criteria which allow the selection of the root that yields result consistent with the loading condition of the problem. The addition of one more set of joints provides the potential to more completely study the interaction of various parameters representing the characteristics of jointed media behavior. Material responses to various loading conditions based on the present constitutive model have been obtained. These results and their comparisons to single joint set results are presented. Formulation of the Continuum Model The inclusion of an orthogonal joint set led to a fourth order algebraic equation for the calculation of stress increments as compared with a second order equation obtained by Thomas. The nonlinear elastic normal joint behavior provides criteria which allow the selection of the root that yields result consistent with the loading condition of the problem. The addition of one more set of joints provides the potential to more completely study the interaction of various parameters representing the characteristics of jointed media behavior. Material responses to various loading conditions based on the present constitutive model have been obtained. These results and their comparisons to single joint set results are presented. Let us focus our attention on the set with normal n first. Let the jump dilation displacement and jump slip dasplacement associated with the [ ]

Jan 1, 1986

By Amy McBrayer, Vladislav Kecojevic, Juan David Valencia Quiceno, Dragan Bogunovic

The mining industry’s commitment to innovation reflects a history of adopting technological advancements to enhance workplace safety, environmental sustainability and vocational training. The objective of this research was to develop an augmented- reality (AR) system for heavy-equipment operators (HEOs) in surface mining. The developed system has the potential to enhance mine safety, training and data-driven decision- making, which presents a significant step toward a more sustainable, effective and technologically driven mining training, contributing to the industry’s evolution and growth. The AR training system leverages Microsoft’s Power Platform and HoloLens 2 capacities to provide operators with detailed and immersive training guides for three mining equipment, including bulldozers, motor graders and haul trucks. AR guides combine speech controls, 3D objects, informative images and explicative videos in the real working conditions to enhance the operator’s learning process. The system has the potential to modify the training structure based on user performance and provides an efficient approach to data collection during training. This project was developed and applied through a case study in a surface mine in the Southern United States.

Feb 1, 2025

By K. C. Kane, D. L. Meredith, B. E. Davis, D. A. Stanley, O&apos

Computer control of the minerals beneficiation process is limited by a lack of adequate sensors to provide information on the current state of the process. Recent reduction in the cost of image acquisition and powerful inexpensive computers make use of computer vision as sensory input in process control a possibility. In the phosphate industry, the amount of apatite in phosphate tailings is estimated by inspection. For machine vision, a simple 256 x 512 color image of the tailings was captured via an inexpensive color video camera on an IBM PC. Initially, the image is converted to gray scale and displayed on an EGA color monitor. A program was written which identifies the different constituents of the sample by analyzing the gray scale levels for the digitized picture. In other instances the minerals are identified by their relative color intensities. The amount of each constituent is determined with good accuracy from the area it occupies on the image.

Jan 1, 1990

By V. G. Papangelakis, G. P. Demopoulos

The high temperature (180-200 OC ) pressure oxidation (02 - HzSO4) process for the recovery of gold from refractory concentrates (FeS2/FeA8S) is simulated with the aid of a computer model. The model centers on the continuous operation of a multi-stage horizontal autoclave. In particular the effects of key process parameters controlling the autogenous operation of the autoclave are critically examined. The building elements of the model are (i) the continuous particle size distribution function of the concentrate, (ii) the residence time distribution function of the slurry and (iii) the shrinking core kinetics. Conversion is calculated on the basis of the segregated flow model. For the calculation of the particle size distribution at the exit of each compartment the population balance model is employed. The effects of feed rate, feed preheating, cooling, autoclave configuration and rate limiting regime (chemical reaction vs. gas-liquid mass transfer) on the autogenous steady state operation are discussed. Finally optimum reactor design and operation criteria are indicated.

Jan 1, 1990

By William J. Francart, Edward J. Miller

The utilization of computer based monitoring systems for fire detection in underground coal mines has grown significantly in the past seven years. In 1984, an annual MSHA survey identified a total of 38 systems being used in U.S. underground coal mines, while a 1990 survey indicated the number has risen to 112. The applications for mine monitoring have also changed according to the annual surveys. From April 24 to June 21, 1990, investigations were conducted by personnel of the Ventilation Division, Pittsburgh Health Technology Center, in cooperation with Coal Mine Safety and Health, concerning the installation and operation of Atmospheric Monitoring Systems in underground coal mines. These investigations were conducted to gather information concerning the ability of the AMS to detect fires and heatings, false and nuisance alarm frequencies, information related to system maintenance, and information related to employee training on system operations. This paper addresses current applications of the systems, fire and heating identification rates, application of systems in dieselized coal mines, system maintenance, and employee training requirements. While deficiencies were identified in some applications, results of the studies and survey indicate the use of atmospheric monitoring systems can be effective in identifying mine fires and heatings.

Jan 1, 1991

By H. Lind

Mining in Estonian oil shale deposit mainly takes place in the Ordovician, Keila-Kukruse aquifer. The aquifer is affected by mining and is fully dried out around the working mine areas (Perens and Savitski, 2008). The groundwater level is decreased down to 30 m, to the mine floor elevation using about 30 pumping stations (Lind, 2005). The pumping rate is very high - depending on the season, ranging from 10 up to 40 m3 per ton of produced oil shale (Reinsalu et al., 2006). The Estonian oil Shale Company mined 15.5 million tons of oil shale in 2007 (Source: Estonian Oil Shale Company). In order to predict the effects, and avoid the social and environmental impacts, there is a need to continuously monitor the situation and run software simulations aiming at decreasing the pumping rate. This becomes even more important since the environmental taxes on usage of groundwater resources increase every year. Therefore, it is necessary to monitor groundwater level and quality, and develop a groundwater model for the overview of the situation during mine operations and also for a number of years after mine closure.

Jan 1, 2008

By Jerzy Iskra, Wlodzimierz Sikora

INTRODUCTION The effect of stress concentration in coal seams leads to a sudden release in the form of rock bursts. This effect is controlled along many lines, but the most efficient methods consist in preventing the accumulation of energy in the seam or in the roof. The over- burden weight resulting from mining is the main cause of excessive stresses in a seam. An additional weighting of roof takes place due to formation of abutment loads. The accumulation of energy in the roof takes place where thick sandstone beds occur in overburden strata. An essential problem is to watch, with appropriate measurements, the stress of coal and roof rocks, and to conclude, on this basis, the degree of rock burst hazard. The methods for determining the stresses in a coal seam are quite well developed at present. Let me mention here the seismoacoustic methods, or borehole overcoring measurement methods. On the other hand, an examination of the state of stress in the roof rocks is almost impossible at the actual stage of development of the measuring technique. Hence, the model of stresses in roof was analyzed and determined theoretically. Based on this model, a technology for roof fracturing was developed which aims at destressing rock masses in a planned way. The essentials of the fracturing method consist of a controlled breaking of sandstone roof beds in order to: - prevent the excessive weight on the pillar - prevent a spontaneous breaking of roof beds at a limiting state followed by sudden energy release. High pressure fluid infusion is used to release buildup of stresses. THEORETICAL AND RESEARCH BASES According to the tests carried out by A. Kidybinski by the method of finite elements, isobars of stresses occurring in the roof over the working face are shown in [Fig. 1]. The results indicate: - the highest values of compressive stresses occur in the roof directly over the seam, at a distance of about 5 m ahead of the working face - at a distance of about 22 m above the seam there is a line of transition of compressive stresses into tensile - within the tested roof area, the highest tensile stresses occur at a vertical distance of 35 m, and at a horizontal distance of 20 m from the line of the working face. H. Gil (1) determined the pres- sure initiating the fracture of roof rocks by the formula: [ ] On the basis of results of analysis of isobars, and of the initiation of failure stress formula (1), isobars may be designed for a given roof class. Assuming for sandstones the Poisson ratio equal 0.3, a field of failure stresses presented in [Fig. 2] is obtained. In this figure it can be seen in which areas the effects of sandstone breakage may be obtained with the operation of a determined hydraulic pressure. To use formula (I), the knowledge of Rr is still necessary. This value may be determined in two ways: - taking a sample and testing it in the laboratory, if there is access to roof rocks in the existing openings, - drilling boreholes in the roof from surface and examination of the rock mass by using hydraulic breaking, if there is no access to roof rocks.

Jan 1, 1982

By D. C. Panigrahi

The paper presents the application of Object Oriented Programming approach for the development of a network simulation model based on nodal pressure method using linearised flow equations. The convergence and computational efficiency of the algorithm have been investigated. Finally the paper re- ports the validation of this algorithm in actual field conditions.

Jan 1, 1996

By Enrique Jelvez, Nelson Morales Varela, Christian Ihle, Joaquin Silva

All mineral beneficiation processes require water for its execution. Therefore, the availability and adequate management of water are key to the existence of any mine operation. However, many mines’ operations are affected by water scarcity and risk an increase of operational costs or even production in some cases. This paper proposes a model to minimize the losses of water due to evaporation and re-absorption by adjusting the active and inactive periods of the discharge in different points of the tailing. When applied, the model determines optimal or nearly optimal discharge operation in all the scenarios that were evaluated.

Jun 25, 2023

By Joel Nonnweiler, Galen Samuelson Nagle

The Sacramento Regional County Sanitation District (SRCSD) has undertaken an interceptor expansion program to meet future wastewater needs associated with projected growth over the next 20 years. The Lower Northwest Interceptor (LNWI) will include over 17 miles (27 kilometers) of pipeline including 14 miles (23 kilometers) of dual force main ranging in size from 54- to 60-inch (137- to 152-centimeter) diameter and 3 miles (5 kilometers) of 120-inch (305-centimeter) diameter gravity pipeline. The estimated capital cost for the program is $331 million, with approximately $236 million in construction cost (as of November 2002). The project includes 4,700 feet (1,433meters) of tunnel including 2 crossings of the Sacramento River and one crossing of the Barge Canal, and 11 other smaller tunnel crossings beneath various creeks, sloughs, highways, and railroads. Preliminary design of the tunnels for the LNWI are discussed in this paper. The overall purpose of the preliminary design was to sufficiently define the project to allow planning level cost and schedule estimates to be performed. There have been changes to the project during final design including pipe sizes and configurations, tunnel and pipeline lengths and anticipated flows. This paper addresses only the preliminary design of the LNWI tunnels. Final design issues and changes made since completion of preliminary design are not addressed in this paper.

Jan 1, 2003

By Sizhe Tan

An open pit mining operation can be considered as a production system with at least two products: ore and overburden (waste). A primary mine planning task is to schedule the production of ore and waste over its life span subject to several technical and economic constraints to maximize some objective such as the overall profit from the operation. Two major constraints are (i) the feasible combinations of ore and waste productions and (ii) the limiting function for ore production as a function of mine life. The task in scheduling production and stripping ratio (ratio of waste to ore production) is to find an ore production curve below the upper bound function of ore production, and a stripping ratio curve within the feasible domain of ore production and overburden removal while maximizing the defined objective. Zn this paper, feasibility of developing computerized optimization models to perform such a scheduling process is explored. Two optimization models are proposed for the task. In the first approach, a linear programming (LP) model is employed and in the second, a dynamic programming procedure (DP) is outlined. In these models, in addition to the consideration of the two major constraints mentioned earlier, various other contributing factors such as interest rate, equipment purchase cost and installation schedule, operating cost, and equipment idle cost are incorporated. An example is provided to illustrate the LP model application.

Jan 1, 1992

By Gregory Owen Lewis, Wendy Bouwer

Various processing strategies have been implemented in an effort to limit the loss of gold, during leaching, to the naturally-occurring carbonaceous 'preg-robbing' constituents present within certain gold bearing ore sources. Certain processing routes include complex and costly pre­treatment steps to reduce the negative effects of the preg­robber prior to dissolution, while others adopt a simpler direct leach/recovery approach. Process selection is largely dependent upon the gold deportment and the nature of the preg-robbing constituents within the particular ore. In the case of carbonaceous ores in which the bulk of the contained gold is available to direct cyanidation, carbon-in­leach (CIL) technology is generally applied with varying degrees of success. The effectiveness of the CIL route is governed by the competitiveness of the preg-robbing constituents in relation to activated carbon for the preferential adsorption of the solubilized gold. Trials have shown that the DOWEX MINIX strong-base gold-selective ion exchange resin has gold loading characteristics superior to those of activated carbon. The faster gold loading kinetics, together with the higher capacity of this resin, favour its use in an in-leach application as a more effective adsorbent for complex ores. This paper introduces the alternative resin-in-leach (RIL) technology, compares the metallurgical responses to RIL processing of different problematic ore sources, and discusses the interaction between various process conditions. Selected results from laboratory and pilot-scale testwork are presented to highlight the discussion.

Jan 1, 2000

By C. Rutter, S. Nelson

"Climax Molybdenum Company’s Henderson Mine, owned by Freeport McMoRan Inc., is a panel caving molybdenum mine located 69 km west of Denver, Colorado. The mine utilizes long interconnected ore passes as part of the ore flow system. Knowing the approximate level of ore in these ore passes is beneficial for preventing increased dust concentrations in various production areas, as well as scheduling truck loading operations. Level monitoring has been achieved by using a strain gauge placed on the steel structure of the truck chute, an amplifier and a Programmable Logic Controller. This paper explains the concepts and limitations associated with using strain gauges for ore pass monitoring as well as applying proactive dust prevention and level monitoring interfaces. INTRODUCTION The Henderson Mine, located 69 km west of Denver, Colorado, is an underground molybdenum mine which uses a panel caving process to produce 18,000 tonnes per day currently. This process involves dumping ore down a series of interconnected ore passes leading to truck chutes. Trucks use these chutes to load ore and deliver this ore to an underground crusher. If ore is pulled below the lowest intercept of these ore passes, a ventilation pressure imbalance occurs which generates a large amount of dust on the levels where ore is being loaded into the tops of the ore pass. When a dust event occurs, work must be stopped until the dust settles. Once the dust settles the ore passes must be filled significantly before trucks can start pulling from the corresponding chute. This downtime and unplanned work due to dust can be avoided if the approximate ore pass levels are known. Strain gauges have been installed and tested on a truck chute at the Henderson Mine and the results of these tests have led to a series of concepts in using strain gauges to monitor ore pass levels. This paper explores these concepts and corresponding limitations and explains how the application of ore pass monitoring can be achieved with the use of strain gauges. Ore Pass and Ventilation Pressure Imbalance Overview At the Henderson Mine, there are typically two or four ore passes in different drifts that combine into one bin to create an ore pass complex as shown in Figure 1. When the level of ore is at or below the 7210 intercept (I82W), four drifts have a ventilation connection to each other and the 7655 exhaust level. A “piston effect” is created each time a bucket of muck is dumped down the ore pass. Figure 2 illustrates this phenomenon: as the loader in 621 dumps a bucket down the ore pass, the muck pushes the air in the ore pass down the 82A leg and back up the 82B leg which generates a large amount of dust. The bin regulators on 7655 cannot be opened enough to allow for this surge of air to be relieved onto the exhaust level and the dust ends up exhausting into the 625 and 627 drifts."

Jan 1, 2018

By J. W. Mahar, E. J. Cording, F. L. Gau

INTRODUCTION The Washington, D.C. rapid transit system (METRO) when completed will consist of 98 miles of double track rail. Fifteen miles will be tunneled in rock and 12 large underground rock chambers will be constructed at station locations. The University of Illinois is under contract to Metro to provide observations and instrumentation services in the initial phase of construction. The work is coordinated through DeLeuw, Cather & Co., the General Engineering Consultant to Metro. The program is designed to monitor construction conditions as well as to provide information useful for the design of future rock tunnels and rock chambers in the Metro system. This paper presents the results of observations in the rock tunnels constructed to date. Most of the observations are in a 5000-ft-long, 30-ft-wide, double track tunnel in downtown Washington, D.C. Observations were also made in single track tunnels, shafts, enlargement areas, and pilot tunnels, and are being made in a large rock chamber 700 ft long, 76 ft wide, and constructed at shallow depth in a schistose gneiss. One of the major objectives of the observational program was to determine the orientation and character of joints and shear zones and to evaluate their effect on support requirements for various tunnel orientations and configurations. The consistency of geologic features throughout the Washington area has made the results of the initial study applicable to evaluation of support requirements on future tunnel contracts. The first section of this paper summarizes the geologic conditions in the tunnel and their effect on overbreak and rock movement.

Jan 1, 1997

By D. Farahmand

This paper focuses on formulating a practical procedure for forming long-range production and development schedules in underground mining. A computer program developed to be run on a microcomputer is presented and discussed in detail, and a practical case study is analyzed to demonstrate the suitability of the procedures discussed in the paper. The intent of the computer scheduling model is to have quick access to vital information when changes in development and production are under consideration by management.

Jan 1, 1986