Search Documents

By S. K. Kawatra, S. J. Ripke

Iron ore pellets use bentonite clay as binder at dosages from 0.5to 1.0% (10 to 20 pounds per ton) of moist iron ore concentrate. Bentonite is typically shipped hundreds of miles from Wyoming to the Lake Superior iron ore district. It is therefore best to know how effective a bentonite will be before it is shipped and used to bind concentrate into pellets. Current tests of bentonite effectiveness include: plate water absorption, methylene blue uptake, free swell, exchangeable cations, and glycolated layer expansion. However, these tests have many disadvantages: First, they only measure the ability of a bentonite to expand, disperse, or absorb, not how well it will bond. Second, most of the tests require up to 20 hours to perform. Bentonite only has a few minutes to interact within the concentrate before it is indurated (sintered). These long-term tests may not reflect the true behavior of bentonite. Third, the tests are tedious and often results are inconsistent between different iron ore concentrates, labs, and technicians. Fourth, some of the testing equipment is difficult to procure. Fifth, procedures are often difficult to standardize. In this paper, the Binder Effectiveness Strength (BESt) test to evaluate binders for iron ore pellets is presented that: measures the ability of bentonite to bond, requires only about two hours to complete, is simple and reproducible, and utilizes readily available equipment that has been standardized for decades.

Jan 1, 2003

By Paul E. Senseny

Data from triaxial compression tests per- formed at confining pressures between 0 and 100 MPa are used to evaluate parameters in a contitutive model that is based on microcracking. The tensorial formulation is reduced to equations that are specific to the simple Loading imposed in triaxial compression tests. Procedures for evaluating the model parameters are described, dependence of parameter values on confining pressure is discussed, and prediction of failure is assessed.

Jan 1, 1986

By C. J. Gilbert

The mining method at the Cannon Mine uses heading and bench stopes, which are subsequently backfilled with cemented high-strength fill prior to pillar removal. The dimensions of the pillars, 24 feet wide by G5 to 95 feet high, re-quire careful blasting in order to not damage the rock, compromising pillar strength and complicating later removal. Additionally, the proximity of dwellings makes vibration control a must for good-neighbor relations. A blast monitoring study was conducted in order to optimize bench blasting practices to maximize fragmentation, reduce costs, minimize well damage, and minimize ground vibration.

Jan 1, 1989

By Joseph C. Rota, Charles E. Ekburg

Introduction The Gold Quarry gold deposit is the largest bulk tonnage epithermal gold deposit in northeastern Nevada to be developed by Newmont Gold Co., formerly known as Carlin Gold Mining Co. Exploration and development of the deposit extended over a period of nearly 50 years before bulk tonnage mining became economically feasible. Proven reserves at Gold Quarry are currently estimated at more than 255 t (8.2 million oz.) of gold, accounting for more than 40% of the total Carlin Trend mineable reserves for 1986. Milling began in late 1985; dump leaching of lower grade ores began in May of 1986. The mill has exceeded the initial design throughput rate of 6.3 kt/d (7000 stpd) and is now processing more than 8 kt/d (9000 stpd). The dump leach facility will process more than 7.3 Mt (8.1 million st) of lower grade ores in 1986. The Gold Quarry ore body is to be developed by an open pit that will eventually be 1830 m (6000 ft) long, 1220 m (4000 ft) wide and 300 m (1000 ft) deep. The mine currently produces 77 kt/d (85,000 stpd) on a 24-hour-a-day, seven-day workweek. Planned pit production will increase to nearly 168 kt/d (185,000 stpd) in 1988. Production equipment currently includes one Demag H-/285, three Komatsu PC-1500 hydraulic shovels, two Cat 992C loaders and 21 90 to 135 t (100 to 150 st) haul trucks. Mining is conducted on 8 m (20 ft) benches within the Paleozoic

Jan 4, 1988

By Thierry Coléou

In this paper, we consider open pit optimization. At present, most methods specify the economic parameters and then find the corresponding optimal pit. But as the economic environment varies (which it does regularly these days), the "optimal" pit changes and quite often changes markedly. The questions are: by how much does it change and which parameters are most influential? The functional approach of Technical Parameterization of Reserves, devised by Matheron in 1975, gives the set of all the different optimal pits, under any economic condition. It separates technical design and economic assumptions and thus permits the use of several optimality criteria when choosing the final pit, and not just the maximization of an additive profit formula. Very efficient specific algorithms are presented to obtain all the potentially optimal pits. Fluctuations in the parameters induce changes in the optimum design. Inclusion relations that exist generate very tight bounds and hence very quickly detect optima, even when using a classical adaptation of maximization techniques (graph theory, moving cone, dynamic programming ...). The advantage of Technical Parameterization of Reserves over other methods is that it provides a nested sequence of optimal pits which can then be used for mine scheduling. Many possible mining schedules can be obtained by using the family of technically optimal projects to split up the orebody. The "optimal" schedule, which is in fact a compromise between the different requirements of the economists, the mine planner and the metallurgist, can be chosen from within the wide scope of possibilities. A practical example of mine scheduling for a chromite mine is presented in detail.

Jan 1, 1989

By P. K. Davis

The results of a previous basic study of the flow and design characteristics of the hydrocyclone has shown that a recovery as high as 99% with a product rating of 0.95 can be achieved on a "batch?2 basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-cyclone system was also sponsored by the U.S. Department of Energy. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1989

By L. J. Laughlin

The majority of non-drive conveyor pulleys use rotating shafts, and typical idler rolls use non-rotating shafts, even though both products are used to support and guide the conveyor belt and its load. This paper will explore and compare the requirements for rotating and non-rotating shaft designs and the impact of that design on the product. Additionally, it will explore how the “roller” bearing types (deep groove ball, tapered, or spherical) affect these designs.

Jan 1, 2003

By K. KAKLIS, O. SAUBI, Z. Agioutantis, R. JAMISOLA

Machine learning in the form of artificial neural networks was applied to investigate whether specimen load evolution can be predicted as a function of acoustic emission (AE) signals in the case of three-point bending (TPB) marble specimens instrumented with piezoelectric sensors. The ultimate objective of this study is to develop a model that can quantify rock behavior under loading that can lead to rock-failure prediction in underground structures subjected to bending, such as roof failure in development or production openings.

Nov 1, 2022

By M. J. Shields

There are numerous suggestions in the literature on methods of obtaining representative samples of waste rock or mill tailings. Some suggested methods would result in thousands of samples and very high costs for a large facility. There is no general rule that can (or should) be followed, such as collection of a given number of samples per mass of material, per acre of impoundment, or per foot of drillcore. Each site is different, and the adequacy of sampling must be tailored to the site. A logical approach is to let the variability at the site dictate the number of samples that should be collected and analyzed, and then to quantify and evaluate the results by means of standard statistical methods.

Jan 1, 1998

A general form of pore pressure in a saturated porous medium, which is subject to external forces it has the pressurization of a borehole in hydraulic fracturing, is derived. The pore pressure consists of two parts: the preexisting initial pore pressure and the pressure induced by fluid flow due to the pressure difference caused by pressurizing the borehole The initial pore pressure associates with the effective stresses in the stress, fields of crustal stresses and a thick hollow cylinder subjected to internal and external pressures. The pure pressure weaned by fluid flow is implied in Biot's (1941) constitutive equation for three-dimensional consolidation and proved to be the exact effective pore pressure (Nur and Byerlee, 1971). Using this general form of pore pressure, a general poroelastic model for hydraulic-fracturing breakdown (fracture-initiation) pressure was derived. This model was validated by laboratory experimental results on Indiana limestone. Three sets of tests were conducted under the conditions of preexisting pore pressures of 6, 21 and 28 MPa, respectively. The equal horizontal (confining) pressures applied in the tests ranged from 6 to 60 MPa. Hainison and Fairhurst's (1967) model appear to be applicable to rocks having microcracks or flows. Experimental results of fracture reopening pressures on Indiana limestone supported this assertion. The test results also demonstrated that, when the pressure difference between the confining and the initial pore pressure grows larger than 14 to 21 MPa, the breakdown pressures agree well with the general poroelastic model developed in this paper. This indicates that the developed model will be superior when hydrofacturing stress measurements are conducted at great depth.

Jan 1, 1997

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts (CCB). Alkaline combustion byproducts are gaining increasing usage for acid mine drainage (AMD) mitigation as research leads to a better understanding of their beneficial applications. Since January 1997, Mettiki Coal has been injecting alkaline flue gas desulfurization material from Virginia Power's Mt. Storm Unit No. 3 wet limestone scrubber into abandoned portions of the active Mettiki Mine.

Jan 1, 1998

By C. N. Speltz

The cost of transportation of industrial minerals is frequently higher than the cost of the product. Where a minc, industrial mineral plant. or customer is served by a single railroad, that single railroad, because of lack of competition, may increase rates and/or provide inadequate service so that the economics of that mine, plant or customer are adversely affected, or so that the level of service precludes satisfactory performance. Transloading of industrial minerals from rail-to-truck or truck-to-rail in order to improve economics and sales of product is not new. However, transloading to reduce freight costs or improve inadequate service caused by a lack of competition in the rail industry, is a relatively new concept brought on by the recent mergers of many of the main line railroads, both in the eastern and western United States. For example, with completion of the Burlington Northern/Santa Fe and the Union Pacific/Southern Pacific mergers, the western United States has only two mainline railroads. The industrial mineral producer, in order to reduce the cost of transportation, or increase the level of service, must evaluate potential transloading opportunities in light of higher prices and reduced service brought on by reduced railroad competition.

Jan 1, 1998

By Jacques H. Nantel, James F. Archibald

INTRODUCTION The use of backfill materials in underground mines has been practiced for many years and the trend indicates an increased utilization of backfill materials in the future. The authors believe that underground uranium mines will follow this trend. Classified mill tailings, approximately 65 to 70 percent solids by weight, are the most common fill materials. Cement or other pozzolanic agents can be added to the fill materials to improve their strength characteristics. Dry fill, in the form of development muck, can also be introduced in the stopes to fill the voids left by the action of mining the ore. This paper deals mainly with the assessment of the radiation properties of backfill materials originating from uranium ores processed in the milling facilities of uranium mines. The paper outlines the results of studies conducted in the laboratory and in the field on radon emanating characteristics of backfill materials utilized in uranium mines. ROLE OF BACKFILL IN UNDERGROUND MINES Fill is a structural component of any underground mining system. In general terms, the purpose of filling is to provide ground support, to make recovery of pillars possible to provide a working platform for men and equipment, and to allow for waste disposal. There are other inherent advantages to the use of backfill underground, the most important being to: a) permit mining at greater depth b) allow the adoption of highly mechanized mining techniques c) reduce dilution from wall sloughing d) minimize roof and wall failures e) allow the mining of irregular orebodies, and f) to provide better control of ventilation. The last item is of great importance to uranium mine operators. The introduction of radioactive backfill underground represents an additional source of radioactive contamination; on the other hand the introduction of backfill in the mine reduces the volumes of workings to be ventilated. As a consequence the general mine ventilation is more effective and in most cases, better air quality can be maintained in the mine. There are of course some disadvantages associated with the use of hydraulic fills in underground mines, notably: a) the handling of large additional quantities of water from the underground workings b) delays caused by the cyclical nature of the backfilling operations c) additional costs associated with stope preparation and placement of backfill in stopes, and d) "spills" caused by bursting pipes or fill escaping from fill retaining structures. ASSESSMENT OF NON-RADIOACTIVE PROPERTIES Although the radioactive properties of mine backfills are discussed in this paper many other physical and chemical properties of backfills must also be considered. These properties include: a) percolation rate and permeability parameters b) viscosity versus pulp density relationships c) size analyses d) settling times e) settled bulk density f) solids specific gravity g) void ratio and porosity h) optimal percentage solids by weight i) specific gravity of slurry j) addition of cement:cement retention and loss k) unconfined compressive strength 1) triaxial compressive strength m) shear strength (non-cemented)

Jan 1, 1981

By R. L. Grayson, S. Yuan

A goal-programming-based, worker-scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model, the accomplishment of each regular and non-regular job is a goal, and the objective is minimization of the deviations from the goals. A number of coefficients are employed as premultipliers of the decision variables to address practical considerations associated with the utilization of workers and the requirements of jobs. This model is applied to a 41-worker problem.

Jan 1, 1992

By G. Gaidajis

For the environmentally safe management of the sulphidic waste rock produced from the Stratoni mining facilities, TVX Hellas has examined, within the frame of the funded European research program ROLCOSMOS, the effectiveness of an alternative rehabilitation scheme involving the segregation of the sulphide rich components of waste rock and the engineered application of alkaline additives. The examined waste rock management scheme was evaluated with laboratory test work followed by pilot-scale field applications. In this paper, the results from the two-year monitoring period of the pilot scale application are presented.

Jan 1, 2002

By T. D. Dreger

In the spring of 2009, Suncor Energy Inc. technical personnel saw an opportunity to improve planning and mining of overburden material in order to address aggressive construction goals and increased mining complexity. By tying together current and historical equipment performance, geological model information, and material observation in the field new operating elevations for the shovels were developed. At the same time, methodology of recording and reporting overburden movement through the Modular Mining DISPATCH system was changed. The result of this first stage of improvements was an increase in construction-grade material available at the face. The personnel involved realized that other opportunities were available to build on the initial successes and establish processes that would stand up to attrition and experience levels. A cross-functional technical team was assembled to identify ways of further improving workflows around overburden mining. Some of the opportunities realized include greater alignment between planning, reporting and operations as well as development of reporting tools that help steward Mine Operations to the plan. All of which have resulted in Suncor meeting or beating its forecast overburden targets. The cross-functional technical team continues to seek out new and better ways of doing business so Suncor can continue to deliver on its commitment of outstanding performance and results.

Jan 1, 2012

By R. Todd Swinderman

Variations in designs between belt cleaner systems are so wide that it is impractical to establish a dimensional stan- dard. The number of variables that affect the efficiency of belt cleaners is too great to assume a required number or style of cleaners for broad classifications of bulk solids or typical applications. The amount of carryback remaining on the belt is more dependent upon the characteristics of the bulk solid and the physical parameters of the conveyor system than it is on tonnage of material conveyed. Therefore, a performance-based standard is proposed. Three levels of cleaning performance are proposed: • Level I cleaning is general specified when concerns about carryback are not critical. Cleaning systems normally associated with achieving a Level I performance are single or double cleaner systems with one-piece blades undergoing poor to average maintenance. Frequent cleaning of the carryback that falls from the return run will likely be required. • Level II cleaning is generally specified when carry- back is of concern but does not create a safety or environmental problem. Cleaning systems normally associated with Level I1 performance are multiple cleaner systems with segmented blades undergoing the manufacturer's specified maintenance. Regular but infrequent cleaning of the carryback that falls from the return run will likely be required. • Level III cleaning is generally specified when con- cerns about carryback are critical. Concerns range from safety to environmental to product contamination. Cleaning systems normally associated with achieving a Level 111 performance are multiple cleaner systems in conjunction with at least one low- volume water spray. Scheduled inspection and the manufacturer's specified maintenance would have to be performed to maintain a high level of cleaning performance. Difficult-to-clean bulk materials may require the use of a washbox system with multiple cleaners using a combination of low-volume eater sprays to lubricate the cleaners and high-volume sprays to keep the washbox and discharge piping freely flowing. Further addition of a water and sludge recycling system reduces the amount of water that ends up in the product to a negligible amount. Very infrequent cleaning of the carryback that falls from the return run will be required. PURPOSE The purpose of this proposal is to propose a standard method for specifying belt cleaner systems based on user expectations and equipment performance over time. DEFINITION In bulk solids handling by conveyor belt, carryback is the material that adheres to the belt after the belt discharges its cargo. PROPOSED STANDARD Required Basic Good Practices There are a number of basic design and operating principles that are good practice for the selection, installation, and maintenance of belt cleaning systems on conveyors in order to achieve "standard belt cleaning performance over time. 1. The Belt Cleaning System shall be designed to meet the performance requirements based on the worst operating conditions and worst bulk solids proper- ties that are expected. 2. Each conveyor discharge point shall be designed to readily accept the manufacturer's recommended minimum number of belt cleaners. In addition, the discharge chute shall be designed to accept, with minor modifications, at least one additional cleaner if it is required.

Jan 1, 2004

By Ronald D. Hill

Acid mine drainage is the result of the oxidation of pyrite and similar iron sulfide material and the release of iron and sulfuric acid into the environment. In addition to the acid water flowing from underground and surface mines, spoil materials in surface mines are acidic and will not support good vegetative growth; thus erosion is a major problem. Lime and limestone are the major neutralizing agents used to treat these acidic conditions. Lime is the reagent preferred by industry for treating acid discharges, although a few companies use limestone. Agricultural lime- stone is used to "sweeten" acid spoils.

Jan 1, 1974

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well approved Tunnel Seismic Prediction System (TSP) has been substantially enhanced for online geological prognosis in underground construction. The method provides high resolution seismic images of the rock mass ahead of a tunnel face via an array of standard anchor rods. These contain3D-geophones and can routinely be installed during the excavation process. A further outstanding feature of the system is the newly developed high frequency repetitive seismic source which can easily be fixed at a tunnel boring machine. A user-friendly software package enables online data acquisition, processing, 3D-visualization, and interpretation.

Jan 1, 2001

By Anna Arkhireeva, John N. Hay

Considerable interest has been shown recently in organically modified silicates (ormosils) because of the wide range of possible applications for these interesting organic-inorganic hybrids. These applications include the use of the hybrids as modifiers of a range of host polymer proper- ties. The ormosils can be synthesised by the conventional hydrolytic sol-gel process, as well as by the non-hydrolytic sol-gel route. To date, however, there are relatively few reports of the synthesis of sub-micron size ormosil particles of well-defined spherical morphology. Here, we report work to date on synthesis of such nanoparticles and also introduce our own work in the area.

Jan 1, 2003