Search Documents

By Desiree Willis

At 6 percent downgrade to a low point beneath California?s Sacramento River, the Lower Northwest Interceptor Sewer was a difficult project from the outset. Project owner Sacramento County Regional Sanitation District (SRC-SD) planned to excavate the V-shaped tunnel in two sections using an earth pressure balance (EPB) machine in soft ground. Muck removal, due to the steep downgrade, was a tricky proposition. ?We did look at muck cars, but determined they were not the best option due to the relatively steep slope of the tunnel alignment. The safety benefits of conveyors on this job were obvious, as there were not the potential hazards associated with muck cars traveling on an incline or derailing,? said Steve Norris, senior civil engineer for SRCSD The successful project represented one of the first instances of a conveyor system being used for a soft ground tunnel boring machine (TBM) application. Several projects in California, including a recent tunnel completed in 2009, have highlighted a growing acceptance of conveyor muck removal in a variety of ground conditions. Conveyors offer higher system availability than more common methods, such as muck cars, as they allow for continual operation of the TBM. The design of conveyor systems must, however, take into account the differences in material between soft ground and hard rock, including belt cleaning features, sealed transfer points and other elements.

Jun 1, 2010

By G. L. Schroeder, C. H. Summers, D. B. Lindsay

INTRODUCTION The requirement that is placed on owners and operators of underground mines to protect workers against the health hazard of inhaling radioactive materials which are short-lived decay products of 222Rn can be satisfied by applying a considerable variety of what we may call "engineering" solutions as well as a number of "administrative" remedies to the problem. The most obvious of the "engineering" approaches has always been that of forced ventilation, in which relatively clean (i.e., radon-free) air from aboveground is drawn or pushed through the mine workings by a system of fans and ducts. This relatively clean air, in sweeping through the drifts, stopes and haulageways, dilutes the radon and radon-daughter concentrations in the air of the mine, and performs the added beneficial function of removing the daughter-mixture quickly enought to limit grow-in of the longer-lived nuclides in the group that make up the "toxic trio" on which the Working Level (IM) unit is based. Effective as the dilution-ventilation method is for control of WL in most underground mining situations, however, the increasing strictness of control measures that have been imposed on the mining industry over the last two decades have demanded measures of even greater effectiveness. In times of poor markets for yellow-cake and other products of the mines, mine operators are pressed to reduce operating costs, and the installation of additional primary ventilation capacity can be a severe burden on a mine that is already laboring under an unfavorable earning power. When traditional dilution-ventilation systems alone cannot meet the requirement for WI, control, radiation safety engineers and ventilation engineers begin to look at alternatives and auxiliary methods. Since the radon which produces the toxic daughter products originates in the rock of the mine walls, and since, in most United States mines, that rock is a porous sandstone through which air can move under the effect of atmospheric pressure gradients, and through which radon can diffuse relatively freely, one way to help control the growth of WL would be to hinder the escape of radon from that reservior of porous rock. An appealing; method for hindering that natural flux of radon-polluted air from the walls of the mine has long been apparent; namely, to apply a low-permeability coating over the surface of the rock, thus sealing the radon in place and, in theory at least, preventing its escape into the mine air. Our 1970 report to the U.S. Federal Radiation Council on the subject of cost impacts of proposed changes in the occupational standards for exposure of underground uranium miners to airborne radon daughters noted the possibility of using polymeric wall sealants as a means of controlling radon-pollution of mine air. Since that time a number of reports have appeared in the technical literature advocating this technique for restraining the escape of radon from building materials, mill tailings, and other materials containing 226Ra, in addition to the surfaces of underground mine workings. During this period, some controversy has occurred over the question of the probable effectiveness of wall sealants in limiting the escape of radon from the rock. Our 1970 report speculated that flaws (cracks and "pinholes") in the coating might be all but unavoidable in practice, and that even a conservative estimate of the frequency of such flaws would lead to a prediction of ineffectiveness. Hammon et al, in a laboratory evaluation of radon sealants conducted by Lawrence Livermore Laboratory of the University of California in 1975 on behalf of U.S. Bureau of Mines, concluded that a wide variety of polymeric coatings would provide "nearly 100% effectiveness" in restrain¬ing escape of radon from mine wall surfaces if applied in "thicknesses between 5 and 10 mil" (125-250 [y]pm). John Franklin and co-workers at the U.S. Bureau of Mines laboratories in Spokane, Washington, have carried the experiments with polymeric sealants through additional laboratory tests and into actual mine environments, reporting that selected sealants could provide attenuation of radon flux by a factor of four (75-80% reduction). Robert Bates and John Edwards of USBM developed a computer-assisted mathematical/physical model that predicts a relatively small effect of flaws in a low-permeability coating on the radon flux from a sandstone-type matrix. FIELD TEST Since all actual experimental work with wall sealants showed some beneficial effect on radon attenuation (even if not as exciting as the "nearly 100%" predicted by Hammon), USBM was encouraged to extend its evaluation to an actual operating uranium mine, and awarded a contract for that work to Arthur D. Little, Inc. in September 1979. We were fortunate in obtaining the voluntary cooperation of Atlas Minerals Division of Atlas Corp., who operate a mill and several underground mines in and around Moab, Utah. Atlas made available for our use a small T-shaped drift in their Pandora Mine in LaSal, Utah, and provided space for instrumentation and recordkeeping by our field crew in a surface building near the mine entry. Atlas also provided electricity and water to the test site, together with assistance in establishing necessary ventilation, removing rubble from the site, conducting periodic WL surveys and furnishing auxiliary man-power for the heavy hard work of coating the walls with gunite prior to application of the polymeric sealant. The generous coopera-

Jan 1, 1981

By Richard K. Thorpe, Francois E. Heuze

The concept of a reusable underground nuclear test facility, named HEDEF, has been under study for some time. This rock chamber would have to be engineered to sustain the repeated mechanical and thermal shocks of internal explosions. In this paper, we summarize preconceptual studies performed in support of HEDEF, including -simple dynamic calculations for internally loaded tunnels, -outline of proof-of-concept tests of proposed reinforcement, - and initial dynamic testing of reinforcement components in an underground high explosive (HE) test.

Jan 1, 1986

By K. Mulukhov

Introduction The depth of open-pit mines continues to increase. The typical designed depth for large quarries is now in the 300 to 600 m (1,000 to 2,000 ft) range, with some quarries even reaching depths of 700 to 800 m (2,300 to 2,600 ft). The cost of handling material from such deep mines can be 60% to 70% of the total cost. The capacity of using a cyclic means of transport, such as trucks or skip hoists, continues to drop as the depth of the mine increases. In addition to the problem of maintaining relatively low slope angles for haul roads, increases in environment pollution and increased fuel consumption make the use of trucks ineffective below 100 to 150 m (300 to 500 ft). In handling large quantities of bulky materials, i.e., more than 15 to 20 Mt/a (16 to 22 million stpy), under fixed terminal points, belt conveyors are preferable in almost in all cases. An exception is when the lump size of the load is too high for the conveyor to handle. Belt conveyors in mines can handle loads having a maximum lump size of no more than 250 to 300 mm (10 to 12 in.). The use of a movable crusher prior to the belt conveyor in an open-pit mine would make the process very expensive. Such an operation could not compete with truck haulage on a cost basis. Belt-car conveyor The main factor that restricts the lump size for conventional belt conveyors is collision impacts between the load-carrying belt and idlers. These impacts are completely eliminated in the belt-car conveyor, which was previously described by Mulukhov (1977). The unique feature of the conveyor is that the load-carrying belt is supported by moving cars. Each car consists of a troughed cross strap that supports the belt with the load and two rollers, on which the cars move along upper and lower rails. Cars are connected by two endless chains revolving over sprockets. The system uses conventional drive pulleys, tail pulleys and return idlers. There are no fasteners between the carrying belt and the car cross straps. The conveyor belt simply drives the cars along by the force of friction between the belt and the straps. A belt-car conveyor was first installed in 1970 at the Karatau mining operation in Kazakhstan. The system was an elevating conveyor with an inclination of 20° and was located on the final part of the truck haul road. The conveyor transferred blasting phosphate ore from the quarry to the crushing plant. A bunker was mounted between the trucks and the conveyor. The maximum lump size was typically 1,200 mm (48 in.). However, there were some lumps as large as 1,500mm (60 in.), which was greater than even the belt width (Fig. 1). Because the prototype belt-car conveyor was intended only for industrial trails, it had a relatively short length of about 50 m (160 ft). Nevertheless, the conveyor yielded a substantial profit over the cost of truck haulage. Naturally, the first question one might ask is why such a system is not now widely used. The reason was the further development of a huge transporting complex for the whole quarry at the base of the belt-car conveyor. After successful industrial trials from 1971 through 1973, which demonstrated the systems engineering feasibility, the State Planning Committee of the USSR included the development of the belt-car conveyor in its plan for the development of the national economy. However, mistakes were made. First, a single organization was not in charge of the development. Second, a plant that was not specialized in belt conveyors was put in charge of the design and manufacturing of the conveyor system. In addition, the crusher was installed before the stacker, which negated the major advantages of the belt-car conveyor. For loading the conveyor, a special blade feeder with pendulum suspension was developed, but it was found unreliable. The main conclusion was that, in-

Jan 1, 2003

By D. C. Mahon, P. G. Sagert, M. R. Legeyt

INTRODUCTION Public opinion, over the effect of industrial development on the environment, has required government to institute guidelines for the protection of the environment both during the development of and after the decommissioning of mines. In no other area of mining has this requirement been more consistently applied in recent times than in the development of uranium mines. Uranium mines have been a focal point because of the very real uncertainties associated with the detrimental effects of radionuclides and the possible hazards of radiation. In order to determine if there is an environmental effect caused by a development or the storage of the mine waste as tailings, it is necessary to know what the quality of the environment was prior to the production of the tailings. This is the reason for baseline data programs. It is neither technically nor economically feasible to completely define the environment in any given region. Therefore, judgement decisions must be made prior to the development as to what aspects of the environment are more likely to be affected by the presence of the tailings, and to what degree. These decisions have evolved over a period of time based on information generated from existing facilities, scientific research, and the development of strong public opinions. This process is not static, but evolves with the growth of information and the technological developments which permit greater control of industrial pollution and waste management. A well-designed baseline program will reflect changes in science, technology and public attitude, even in advance of government regulations to enforce policy changes. RATIONALE FOR PREOPERATIONAL BASELINE STUDIES There are three distinct phases to be considered in the construction of an environmental assessment for a uranium mine tailings containment facility. I. Pre-operational 2. Operational 3. Post-operational (decommissioning and long term).

Jan 1, 1980

'IM existing predictive methods were chosen for evaluation; an influence function (Bals Theory) and a profile function (hyperbolic). These ere applied to several field measured subsidence profiles over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1982

By M. Kaya

The main purpose of this study was to design a modular/mobile coal preparation plant with a capacity of 300 t/h for Seyitömer B3 vein (almost 70% of the whole SLI deposit). Firstly, coal washing properties and washability curves were determined by sink and float tests. Then, equipment sizing, selection, flow sheet development, economic evaluation, investment and operating costs were determined for coarse (-150+18mm), fine (-18+0.5mm) and slime (-0.5+0.1mm) coals. Economic evaluation of the proposed flow sheet showed the feasibility and profitability of the investment.

Jan 1, 2006

By G. A. Hazen, S. M. Sargand

This study monitored longwall mining subsidence profiles over three panels that were mined beneath state highways in southeastern Ohio. The average maximum subsidence was 1.07 m (3.5 ft). The average maximum compressive strain recorded was 0.008 mm/mm. Three predictive methods for the determination of displacements and strains were compared: the National Coal Board (NCB) graphical method, the profile method with empirical constants determined for southeastern Ohio, and a finite element excavation program. Excellent subsidence agreement was found with the profile method, and reasonable strain agreement was determined with the finite element program.

Jan 1, 1987

By V. K. Karra

Research by various workers has shown compressive comminution to be significantly more efficient than impact comminution. Based on the work being done at Nordberg, wet compressive crushing in cone crushers producing finer and finer products, shows the feasibility for partial substitution of conventional tumbling mills. For further substitution, major challenges are processing of fine feed slurries in cone crushers to realize a significant size reduction of the particles, and understanding the limitation of the gyratory type units in terms of finest product achievable. The paper addresses the challenges involved, efforts at Nordberg, and the implications to conventional comminution flowsheets.

Jan 1, 1989

By Ron Parks

High Pressure Grinding Rolls (HPGR) was introduced to the mineral processing industries in the mid-SO's as a tool for comminuting raw and processed materials. This tool made its an impact in the Cement Industry where it was used as a pre-grinder on existing ball mills, raw and finish grinding in a mill circuit and other various applications. This concept was a big success where the cost of power was high along with the desire to increase capacity. The HPGR reduced the power requirement and increased the capacity in the ball mill due to the finished product produced by the HPGR and the micro fractures in the coarse rock, which reduces the power required to finish grind the rock. This unit has found acceptance in many other industries including diamonds, iron and other selective applications. The diamond industry uses this tool for selective grinding purposes since the kimberlite rock is considerably softer than the actual diamonds. Therefore within a bed of material, kimberlite is crushed to fines and the diamonds are liberated and unharmed. The iron industry primarily uses this tool for concentrate comminution; however, there are installations using this tool as a pebble crusher and in an AG-pebble mill circuit.

Jan 1, 2000

By Arthur P. Chaves, John A. Meech, Vanessa M. Torres

Process choice for a refractory gold ore can become a controversial issue, especially at the early stages of a project. This happens since at preliminary stages, a simple economic comparison among the main process options is not possible as the differences are usually smaller than the precision of estimates. This paper presents a methodology to assess the suitability of each available technologies using a heuristic approach, were technical, economic, operational and environmental aspects are taken into account using a neural network methodology. This methodology is embedded in an expert system for gold ore process design, Intelligold, which is in the final stages of development.

Jan 1, 2000

By A. W. Laughlin, C. R. Mansfield, M. J. Ferris, D. A. Cremers

Analytical costs are a major part of exploration programs in developing nations which may lack adequate laboratories. Laser-Induced Breakdown Spectroscopy (LIBS), a variant of atomic emission spectroscopy, can reduce exploration analytical costs and can provide the analytical results in <1minute. CPI is now marketing battery-powered, backpack mounted analyzers, using LIBS to analyze for many elements of interest to the explorationist. LIBS is well suited to the analysis of elements in industrial minerals. Limits of detection in ppm for some of these are: Li-1, Be-2, Na-100,B-33, Sr-10, Ba-300, Cs-1, K-500, Fe-500, Mg-500, andTi-500.

Jan 1, 1999

By S. R. S. Sastri, G. V. Rao

Because the nickel contained in lateritic nickel ores does not occur in an identifiable mineral, it is generally accepted that these ores are not amenable to beneficiation. For this reason, such ores are either directly smelted or leached to extract the nickel. In this paper, a process for enriching the nickel content of the lateritic nickel-bearing chromite overburden, normally a waste material generated during chromite mining, is described. In this flotation process, a nickel preconcentrate containing >1.1% Ni was obtained from material containing as little as 0.36% nickel. An empirical relationship was developed to predict the grade of nickel that can be obtained.

Jan 1, 1997

By Kerstin Malmqvist

Simulation technique has been used for a feasibility study of a deep exploration project for massive, sulphides in an old mining district, the Skellefte field. An interactive computerized mathematical model of an ore field and a drilling procedure has been constructed. It is possible to represent varying geological structures. The model also takes in consideration economical factors such as drilling costs and ore values. On this model Monte Carlo simulations and probability calculations are done in order to estimate the outcome of different drilling strategies under varying geological assumptions. Under the specific conditions of the well known Skellefte field, it is found to be possible to even calibrate the mathematical model.

Jan 1, 1979

By J. Fuller, L. Marsden

Windborne dust from alkaline salt flats and mining-related tailings ponds is especially prone to threaten applicable ambient air quality standards. Sodium carbonate crystals, typically present, weather to an exceedingly fine, non-cohesive dust, causing air quality problems for miles downwind. Recently developed specialized polymers react with alkaline dust to form sturdy, wind-resistant crusts with good longevity. An on-going demonstration project at a major trona facility has developed techniques for cost-effective application of these polymers over large areas of soft tailings or sediments in a wide variety of situations. Recently treated areas on the order of 80 acres show effective suppression of dust.

Jan 1, 2004

By Thomas Fliess, Klaus-Christof Ritter, John R. Sturgul

The optimum flow of materials through a smelter is an extremely important phase of the mining cycle. A typical copper smelter will have up to $US 1,000,000 per day of copper being processed. The motion of the overhead cranes in moving the ladles filled with copper matte and slag from furnace to furnace is prescribed but there can be numerous variables to consider. Some of these variables to the system can be: the speed of the overhead cranes, the number of cranes, the size of the ladles, the size of the furnaces, the number of furnaces and the sequence in loading the furnaces. A simulation model was constructed of a working smelter in the SW of the United States. The model has been used to study the effect of varying parameters of the system. The program runs as follows: an input menu appears on the PC screen and the user can navigate through it and change any of the data; the simulation takes place and the results of the simulation sent to a data file. Animation of the system then is shown on the screen in "cartoon" fashion. The software chosen for the simulation was GPSSI H (&apos;) and PROOF Professional (&apos;) for the animation. The model presented here is believed to be the first reported simulation and animation model for a complete, working smelter.

Jan 1, 1996

By Dao De Xu, Heechan Cho, Mark S. Klima

A study was conducted to determine the feasibility of using dense-medium centrifugation for separating fine (-150 µm) coal. A centrifuge provides the capability of varying the rotational speed and retention time independently, which offers the potential for a higher degree of control as compared to a dense-medium cyclone. Tests were conducted with a 140-mm diameter by 76-mm long Plexiglas separator, which was fitted with appropriate feed and discharge pipes to allow continuous separations to be made. A suspension of ultrafine (-10 µm) magnetite and water was used as the dense medium. The effects of operating conditions, including the magnitude of the &apos;g"-force and retention time, on centrifuge performance were investigated.

Jan 1, 1995

By P. D. Chamberlain

Agglomeration for the heap leaching of gold and silver ores is the process of attaching fine ore particles-less than 150 µm (100 mesh)-to coarser particles. The fines are thus immobilized and uniformly distributed throughout the heap. This is needed to make heaps more porous and uniformly permeable to the flow of a leaching solution. This article describes liquids and binders used to form agglomerates. Agglomeration techniques and equipment are also described. These include drum and disk agglomerators, stockpile and belt agglomeration, and the use of vibrating deck and reverse-running conveyors. The need for agglomeration The main reason for agglomerating heap leachable ores is to prevent percolation problems in a heap. This is different than pelletizing iron ore. In the latter case, the purpose is to bond very finely ground material into coarser, strong particles. These particles can then withstand the rigors of transportation and the loading forces in a blast furnace. Most percolation problems in heaps are caused by the segregation of coarse and fine particles during heap construction. This segregation creates areas with significantly lower permeability because fines plug the channels between coarse particles. Consequently, the leach solutions are subject to channeling, following the path of least resistance. They percolate downward through the coarse ore areas and bypass or barely wet areas that contain large amounts of fines. This results in lower extraction, longer leach time, and higher reagent consumption. Permeability problems in heap leaching are compounded because of the vertical migration of fine particles after the heap has been built. These fines eventually accumulate in pockets or layers and impede uniform solution flow. The fines move because they are not attached to a coarser particle. Moreover, the sluicing action of leach solution flowing over the surface of particles may break the bond between fine and coarse particles. Some fines are also created by the decomposition of ores after being wetted. Percolation problems are minimized if the fines can be attached to the coarser particles. Fines are thus uniformly distributed and rendered immobile within the heap. Heinen (1979) conducted comparative tests of nonagglomerated and agglomerated gold and silver ores. He showed that percolation rates through agglomerated material usually are improved by 10 to 100 times. This reduces leach time for economic recovery to less than one-third of that for nonagglomerated material, and total recovery may be increased. Cyanide consumption is also reduced in most cases because of the shortened leach time. Even run of mine (ROM) ore should be agglomerated. This can be achieved with moderate success by passing each truckload of ore under a water spray to bring total moisture of the ore up to about 8% to 10%. The ROM ore will mix when the ore is dumped, when it cascades down the slope of a heap, or when it is pushed up with a dozer. Overall, agglomeration allows low-cost heap leaching technology be applied to gold and silver ores and tailings that could not be economically processed by conventional methods, according to Phariss (1982). How agglomeration works Agglomeration means that the clays and fine particles contained in the ore adhere to the coarser particles. This creates a coating of fines around the coarse particles. When the ore has few fines and the percolation problems are not severe, the addition of a liquid may be all that is necessary to make the few fines adhere to coarser particles. However, when the quantity of fines is substantial, e.g., +10% -75 µm (-200 mesh), a binding agent may be needed. Use of solution only for agglomeration There are many forces that cause agglomeration and one of them is the surface tension of water. Water-saturated particles collide with each other or with

Jan 12, 1986

By PATRICK R. TAYLOR, NICHOLAS BELLUSCI, D. ERIK SPILLER, VICTOR BRAMAN

Most of the world’s production of natural soda ash comes from the mining and processing of trona found near Green River, WY. The processing of trona ores to ultimately yield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale, is water and energy intensive. It is speculated, however, that the glass-manufacturing industry, which is the largest consumer of soda ash, may be able to use product of a lower grade and consistent level of the insoluble constituents. Thus, the viability of using sensor-based sorting to produce a beneficiated trona stream that would be fed to calcination was investigated. The study encompassed the preparation of a run-of-mine (ROM) Green River ore sample; selection of specimens sized 25 to 75 mm; imaging of the specimens by sensors based on X-ray transmission (XRT), color and laser-induced fluorescence (LIF); insolubles analysis of the specimens; and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content exists, and that a surface-detection-based sensor, particularly LIF, is apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65 percent separation efficiency and a 70 percent recovery of trona could be achieved.

Feb 1, 2023

By Barbara J. Arnold

Combat Infantrymen’s Badge and Bronze Star Medal. Following his discharge from the Army, he re-entered SDSM&T in 1946 and earned a B.S. degree in Metallurgical Engineering in 1948. He then received an M.S. from Montana Tech (MT), worked several years in industry and then as an Assistant Professor at the University of Washington (Seattle). He joined his Montana Tech colleague, Douglas W. Fuerstenau, at The Massachusetts Institute of Technology (MIT), receiving his doctorate in 1957. While at MIT, he married Clare M. Donaghue of Dorchester, Massachusetts, in 1955

Jan 3, 2022