Search Documents

By J. B. Gwiazda

In designing mine workings and adequate roof supports, it is indispensable to determine properties of the strata surrounding the workings. The proper selection of roof supports is based, before everything else, on a thorough knowledge of the roof rock strength, especially tensile strength. This parameter is a vital factor in the delamination of roof rocks and eventual cave-in. It is also important to know the properties of the floor on which the roof supports are set. While driving galleries, it is essential to know beforehand the strength of rocks that will be encountered in the near future during the work. The devices described will help to obtain this information.

Jan 1, 1987

By Richard Druesedow, Richard Ray

Tests at the VP-5 "C" shaft fan installation of Island Creek Coal's Virginia Pocahontas Mines were performed to determine pressure drop due to the design of the shaft collar and ductwork leading to the fan. Data from the test locations in the shaft, duct and fan indicate significant pressure losses in the system as well as significant turbulence in the flow. Data taken with a 3-D probe in the fan annulus confirmed the importance of using this type of instrument in turbulent flow applications. This data will be later supplemented with data taken after addition of turning vanes in the 45° turn adjacent to the fan inlet.

Jan 1, 1993

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10 µm. The test conditions included centrifuge howl and scroll speeds, volumetric feed rate, solids concentration and pond depth. Centrifuge performance was evaluated using size selectivity curves and the corresponding performance parameters, along with product yields and solids concentrations.

Jan 1, 2002

By P. T. Luckie

More efficient classification with a single hydrocyclone through equipment and/or operating design changes does not appear possible. However, improvement in classification efficiency by increasing the sharpness index and decreasing the apparent by-passing while changing the cut size is possible through proper staging of inefficient hydrocyclones. But feasible multistaging requires achieving the necessary material balances around the units. Because of the interactions among the units, these balances require extensive iterations. The final step before commerical installation should be a laboratory demonstration, in order to define the control algorithm required to maintain stability. However, eventually a sufficient knowledge base should be developed that will permit simulation in place of laboratory testing as well as the incorporation of a feed forward strategy.

Jan 1, 1989

By St. E. Deák

Mining activities involve excavation from underground to the surface of large quantities of ore (e.g. uranium and its disintegration products) (Dumitrescu, 2002, 2007). Material with limited content of uranium, deemed as sterile or low-radioactive is mainly stored on the surface. These wastes modify the configuration of the disposal areas and affect the quality of the environment and the landscape. This paper presents both analytical and numerical models related to stability assessment of uranium mining waste dumps. It is focused on the calibration procedure of the numerical models, in order to minimize risk error during stability prediction and avoid long term environment pollution.

Jan 1, 2008

By Alfred W. Hefferan

A longwall face conveyor system serves the primary function as all material handling systems; i.e., to transport material between the source and its destination. However, the conveyor system must provide many other functions as opposed to the traditional belt conveyor system. In this paper, we will attempt to contrast the longwall face conveyor system with a belt conveyor system. In addition, the unique problems encountered along with the solutions to these problems will be covered. Table 1 lists the characteristics required of each conveyor system. The table demonstrates the contrast in the two systems. Both must be designed specifically to encounter its unique problems. The balance of this paper will explain how the longwall face conveyor is designed to address its requirements.

Jan 1, 2000

By Sangwhui Cho

In comminution processes including crushing, grinding and pulverizing, the efficiency of the comminution system is very low. Since the early 1980s, research has been conducted to increase the efficiency of pulverizing mills. Additionally, the application of microprocessors and Personal Computers to process control have come into general use. Given appropriate models of the process and control algorithms, these systems can economically control comminution processes. The ring-roller type mineral pulverizer is known as an energy saving mill. In this study, a control strategy to increase the efficiency of this type mill is explained.

Jan 1, 1992

By A. Maréchal

It has been shown since a few years that the problem of estimating recoverable reserves should be solved by using specialized statistical techniques : whenever the selected blocks are chosen without any other constraint than a cut-off grade criterion, the problem of estimating the corresponding tonnage-grade curve is resolved by estimating the local histogram of block grades. Two major statistical techniques are currently used by geostatisticians to estimate local histograms : the "average conditional distribution" technique (Parker, Journel, Dixon 1979) and the disjunctive kriging technique. (Matheron, 1976, Jackson, Maréchal, 1979). Both have proved to be applicable in practice, with their pros and conconcerning their practibility and versatility.

Jan 1, 1982

By John A. Herbst

Mineral processors have evolved from "handbook-based" decision makers to "model-based" decision makers. With this evolution have come significant improvements through increasing productivity, decreasing capital and operating costs and increasing product quality. This paper traces the development of model-based decision-making technology over the last 40 years and documents the benefits resulting from systems optimization using these tools. Some speculation is ventured concerning the future of model-based decision-making tools and their use in the field of mineral processing.

Jan 1, 2000

By F. G. Miller, M. Polat, S. Chander

Flotation was used to achieve improved separation of magnetite from the float and sink products obtained from heavy medium separation and to reduce the load of the medium cleaning circuit. The investigation was carried out in two successive phases. In the first phase, tests were performed on in-plant samples from the Homer City Coal Perdition plant to determine what effects variables such as medium density, particle size and magnetite source had on the efficiency of the process. In the second phase, the optimum conditions determined in the first phase were used to determine the applicability of the process to other selected coals from central Pennsylvania. It was observed that flotation was very effective in the separation of magnetite from coal. In most of the cases investigated, the magnetite recovery was approximately 99% with a magnetite grade ranging from 95 to 99%. The grade of the magnetite decreased as the ash content of the coal increased and the particle size of the magnetite decreased.

Jan 1, 1994

By John A. Herbst, K. Rajamani

Process improvement is probably the most widespread objective of mineral process plant operators in the late 1980's. An important part of such improvements is dynamic optimization which involves reacting to inevitable plant disturbances in such a way that productivity is maximized at every instant of time. This paper describes the way in which mathematical models can be and have been used in dynamic optimization. Both off-line and on-line model applications are described.

Jan 1, 1989

By Raj K. Singhal

Three principal activities are involved in planning and developing a surface mine. These are 1) definition of economic and technical feasibility, 2) design, procurement and construction, and 3) mining and reclamation. The last is the only activity which begins in the feasibility study and continues throughout the life of a mine. It is also the activity which depends heavily on use of computers. This paper deals with a method of selecting mining software and dwells on the recent progress, made in this area. Discussed also is the status of computerized equipment management and information systems: a microprocessor based technology applied to dispatch systems, monitoring of equipment health and performance, wireless data transmission to a centralized data processing unit, and mine- wide information and reporting system. Reference has been made to upcoming developments which offer the potential- of transforming the surface mine of the year 2000 into a "manless pit". Canadian achievements in all of these areas have been highlighted at appropriate places in the text.

Jan 1, 1989

By M. Poulton

Backpropagation, learning vector quantization, counterpropagation, functional link, probabilistic, and. self -organizing map are among the most popular neural network classification paradigms. Each paradigm finds a unique set of weights that will map the input pixels into their respective output classes. The usefulness of each network depends on its overall accuracy, ease of use, speed and scaling. The fastest and most accurate networks in this study were the functional link and counterpropagation. These networks, however, do not scale well to large input vectors or large training sets. A better choice is the LVQ network which achieves high accuracy, is fast, requires a minimum number of input parameters and presents fewer scaling problems.

Jan 1, 1992

By George McArthur

GEOLOGY One of the largest copper resources in North America occurs in the Bingham mining district, located 40 km (25 miles) southwest of Salt Lake City, UT. Anaconda's present contribution to the development of this resource is the Carr Fork mine. (Fig. 1, Bingham district plan map.) The Carr Fork story began about 300 million years ago when a thick sequence of sedimentary quartzite and limestone was deposited in the Oquirrh Basin. Subsequent earth stresses formed a series of west-northwest-trending overturned anticlines and synclines that were later offset by northwest-striking thrust faults and northeast-trending normal faults. (Fig. 2, Bingham district cross section.) About 38 million years ago the Bingham stock was intruded into some of the folds, resulting in the formation of porphyry ore in the intrusive, and fissure, replacement, and skarn ore deposits in the sediments. The Carr Fork skarns were formed preferentially in two limestone units, called the Yampa and Highland Boy, which average about 46 m (150 ft) in thickness, separated by about 76 m (250 ft) of quartzite. Copper mineralization consists almost entirely of chalcopyrite associated with pyrite and molybdenite in a gangue of garnet, diopside, magnetite, quartz, and carbonate. Molybdenum, gold, and silver are economic byproducts. (Figs. 3 and 4, indicated ore in plan and section.) EXPLORATION HISTORY The West Mountain mining district, of which Carr Fork is a part, was organized in 1863, after leaf-silver ore was discovered in the Carr Fork of Bingham Canyon. However, it was not until 1873, when the Bingham and Camp Floyd railroad to the town of Bingham was completed, that the mining camp flourished. Many small mining companies in the district were reduced, often through consolidation. By 1937 only the National Tunnel and Mines Co. was active in the Carr Fork area. In 1948 it declared bankruptcy, and was later purchased by The Anaconda Co. Anaconda conducted geologic investigations in the Bingham district until 1968, when a concerted diamond drilling program was initiated to fully evaluate the geologic potential of the Carr Fork area. The exploration program commenced with one diamond drill, but was enlarged to three drills following discovery of the first major ore intercept. Near completion of the exploration effort, large oil well rotary drills were used to drill to depths of 762 to 914 m (2500 to 3000 ft), after which the holes were completed by standard diamond drilling techniques. All holes were collared vertically, but considerable deviation occurred because of structure and rock conditions. Wedging and directional drilling were used to keep the holes on target and to provide multiple ore intercepts in the deeper holes. Geophysical surveys, in-

Jan 1, 1982

By Thomas N. Walthier

Exploration is the systematically financed and technically oriented search for mineral wealth. Almost all established mining companies have an exploration department. The size of a company's search varies over the years as the company's profits, or the corporate philosophy change. While the established mining companies have exploration departments, they are also alert to acquiring discoveries made by others -- especially by prospectors and small companies without the resources to develop their find. The emphasis in some large companies stresses self-generated discoveries while others rely heavily on acquisitions; again, over the years the emphasis may alternate. In the last analysis, essentially all new mineral wealth was found through someone's exploration effort. Before we discuss how exploration is financed, it will be informative to analyze how discoveries have been made and by whom. Recently, the author conducted a survey of randomly selected major mining companies to answer these questions. Most companies responded and many went to considerable effort to give complete and detailed answers. I thank all for their help and cooperation. The questionnaire is attached as Appendix I. Appendix II is a list of the 400 companies that replied in a complete enough manner and format to be analyzed here. The results of the questionnaire are given in Table 1. Over 57% of the new orebodies acquired by 40 major mining companies during the past quarter of a century were generated

Jan 1, 1977

By Y. C. Lo

Grinding process optimization is an exciting new tool for maximizing the performance of existing mineral processing plants. This paper discusses the methodology of optimization which involves plant sampling, pilot tests, modeling, computer simulation and plant verification. The methodology developed emphasizes the interactions among operating variables and design options. Two example applications demonstrate that AG and SAG optimization provides the basis to increase grinding throughput up to 10 percent. This sys- tem optimization technology has been proven to be very cost effective for grinding plant performance improvement.

Jan 1, 1998

By T. Knuutinen, M. Klemetti, P. Mörsky

This paper presents a comparison study done at VTT's new pilot plant facilities in Outokumpu, Finland, for chromite ore. The ore was ground in a rod mill -, a ball mill - and high pressure roller mill - ball mill circuit in the capacity range of 0.5 - 3.0 t / h. The main grinding characteristics are discussed and the quality of the products are compared from the mineralogical point of view. The benefits of high pressure roller mill comminution for further mineral processing of chromite is also discussed.

Jan 1, 1995

By J. N. Economopoulos

The mining industry is becoming increasingly aware of environmental issues and has made big forward steps in the field of environmental management. Legislation, social pressure and competition introduced changes in the industry?s policies and practices in order to conform to the new standards of environmental performance. The paper addresses the need for an integrated and systematic approach to the issues of environmental management within the mining industry.

Jan 1, 2002

By Keivan PakIman, Maziar Pasdarpour

Transportation tunnels are highly sensitive to ground movements and are required to be stable and secure for safe operation. In urban areas, the interaction between tunnels and adjacent piles, which are widely used to support buildings and other structures, requires careful consideration. The seismic response of tunnels may vary depending on the lateral stiffness and strength of the tunnel walls, while the axial loading and seismic impact of adjacent piles may cause soil displacement and stress changes that can damage the tunnel lining. As a result, tunnel owners often impose strict limits on the design of new piles lying close to existing tunnels including maximum allowable tunnel deformation, stress change limits, and minimum tunnel to pile separation distances. This paper describes a numerical analysis of the inuence of the axial loading and seismic impact of bored pile foundations on subway tunnels, undertaen using the nite element software laxis D. ased on the results of the numerical analysis, the paper suggests a more realistic and less conservative approach for designing piles in close proximity to transportation tunnels. INTRODUCTION The interaction between tunnels and adjacent piles can cause stress changes and displacements in the soil and structures which may adversely impact structural performance and tunnel safety. It is therefore important to take account of relative load transfer and piling conguration when designing new piles in

Jun 23, 2024

By Debra C. Man, S. Thomas Freeman, F. Wiley Horne

INTRODUCTION The Metropolitan Water District of Southern California (Metropolitan) is the largest water wholesaler in southern California. Its service area spans the major urbanized portions of Ventura, Los Angeles, Orange, San Bernardino, Riverside and San Diego counties. More than 15 million people are serviced by Metropolitan through its 27 member agencies. The primary sources of Metropolitan's water supply are the Colorado River Aqueduct (CRA) and California's State Water Project (SWP). Currently, planning and design level studies are underway by Metropolitan to expand the water storage and conveyance systems within the service area for the purposes of providing increased efficiency and flexibility to manage limited water supplies, improving water quality, and increasing system reliability. The system reliability issue is particularly significant because the conveyance facilities from both the CRA and the SWP must cross the active San Andreas fault. This fault is considered to be the source fault for the anticipated "Big Earthquake" in southern California. To meet these objectives, Metropolitan's expansion plans involve a major new storage reservoir, new large diameter pipeline and tunnel conveyance facilities, more efficient utilization of existing groundwater basins, and an aggressive public awareness and conservation program. This paper focuses on the planning studies that have been carried out for over 50 miles of tunnels being considered for several of Metropolitan's proposed conveyance systems. These tunnels have ranged in length from a few hundred feet to over 42,000 feet, with depths of cover ranging from a few tens of feet to over 3,000 feet, and finished diameters ranging from 10 to 20 feet.

Jan 1, 1993