Search Documents

By A. V. Glembotsky, N. A. Greshnova, V. P. Seregin, V. A. Glinkin

Based on a new alternative depressant of zinc sulphide - dimethyldithiocarbamate- modern technology has been developed for the treatment of complex polymetallic ores. In addition to its general function (depression of sphalerite and iron sulphides to some extent), this double-acting reagent is a promoter for galena and silver minerals. Laboratory and plant tests, as well as industrial experience have all shown consistently higher silver recovery to the lead concentrate as compared with sodium cyanide, resulting in less pollution and a safer environment

Jan 1, 1995

By John Frostiak, Don Welch, David Landriault

The use of paste technology for underground cemented backfill is widely accepted in the mining industry today as a potentially cost effective alternative to cemented rock and hydraulic slurry fill. While paste backfill is not the appropriate backfilling method for all mines, there are presently 23 operating tailings paste backfill plants throughout the world. This new technology has gained increasing acceptance as a backfill method over the last decade and its use is now expanding into the surface disposal of tailings using the stacked, thickened tailings disposal concept. Over the next 18 months there will be ten new paste plants commissioned in the world. Five of these ten plants will be used exclusively for surface tailings disposal or a combination of surface disposal and underground backfill production. The thickened tailings disposal concept, developed by Dr. Eli Robinsky in the early 1970's, has been in use for decades at several mine sites throughout the world (Kidd Creek Mine site in Northern Ontario), but always utilizing non segregating high density tailings slurry central discharge, stacked tailings placement. With the use of a higher solids content paste, the typical 2-degree beach angle can be increased to ten degrees or more with no runoff water and minimal shrinkage crack development through desiccation. This paper presents the design of the first mine to implement true surface paste disposal, Barrick Gold Corp's Bulyanhulu Mine in Tanzania. The paste system will be commissioned in the first quarter of 2001 allowing performance data to be collected to define the full potential of paste technology for surface tailings disposal.

Jan 1, 2001

By R. J. Pruett

Selective flocculation enables the production of high-brightness kaolin products from kaolin ore once considered too poor in quality for beneficiation into paper-coating pigments. Anatase, Ti(1-X)FeXO2, with X = 0 to 0.05, is a common iron-bearing impurity in sedimentary kaolin that can be unresponsive to kaolin beneficiation processes, such as magnetic separation, due to its extremely fine particle size (<0.3 µm), or chemical bleaching, because of its chemical stability. Described here are selective flocculation technologies that separate anatase by flocculating anatase or flocculating kaolinite from dispersed slurries. Applying the advances in the chemical and mechanical dispersion of ultrafine particles and the selective aggregation of kaolinite or anatase particles have resulted in the selective flocculation processes practiced today that have increased process recoveries from those technologies practiced beginning in the 1960s.

Feb 1, 2012

By Erwin Riyanto, Roy William, Karl Llewellyn

The Deep Mill Level Zone (DMLZ) mine is currently one of the deepest block cave mines in the world. The rock mass is heavily veined with little to no joints and faults are usually healed cohesive structures leading to difficult cave mining conditions. The caving process is improved if the rock mass contains fractures with sufficient density that it will cave by gravity as undercutting progresses. Hydraulic fracturing (HF) has been used to create fractures around the cave to improve mining. A seismic monitoring system has been used in DMLZ since the start of mining. Therefore, the seismic activities before, during and after HF can be monitored. Shear wave splitting is a process used to study the impacts of HF on the rock mass. This process involves the measurement of travel times from splitting shear waves after seismic events and using this to define the anisotropy within the rock mass and subsequently fracture density. This paper sets out the methodology for carrying out the interpretation of the shear wave splitting process using seismic data from the fracked cave crown and abutments along with an overview of the benefits to cave mining as result.

Apr 26, 2022

By J. R. Caylor

The Mine Safety and Health Administration (MSHA) advanced several initiatives last year to further protect miners&apos; health. Regulatory efforts included the implementation of a Hazard Communication rule for all mines, work on the Single Sample rule for all coal mines, and the Plan Verification rule for underground coalmines. Development and application of new technologies are actively encouraged in preventing miners&apos; hearing loss and respirable dust overexposures. MSHA&apos;s successful x-ray program for screening of black lung among coal miners completed its third year. Compliance Assistance efforts are focused on Best Practices, outreach, and technical support for operators&apos; specific challenges.

Jan 1, 2003

By Jacob D. Baker

Sulphur dioxide is a versatile gas which has many uses throughout Pulp & Paper, Chemical, specialty Chemical, Mining and other industries. During recent years, S0 2 consumption and distribution patterns have resulted in renewed interests for liquid S0 2 and on site gaseous S02 manufacturing facilities. one relatively new use for S0 2 in the Mining Industry is its use for cyanide detoxification. Our purpose in this paper is to describe the process steps, economics and general technical features of so 2 gas generation using a Jet Type sulphur Burning System.

Jan 1, 1991

By B. Towson, R. F. Dalton, G. W. Seward

This paper reviews the successful application of oxime reagents for the solvent extraction of copper and considers the role that well focussed research initiatives can play in bringing further radical change to the metallurgical industry. Particular reference is made to the Cuprex Metal Extraction Process (CMEP), for the treatment of low grade or difficult to treat sulfide concentrates, using the reagent Acorga CLX- 50 to recover the copper and the reagent Acorga ZNX-50 for the recovery of zinc from chloride solutions. Other new extractants, currently in development, are also referenced.

Jan 1, 1994

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery Recent developments in electrooptic inspection of dry and wet material leaving a grinding device are critically reviewed New methods for characterizing ultrafines are discussed A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine Index and other fineness indices is described

Jan 1, 1983

By S. C. Suboleski

Forecasts indicate that the acid rain bill currently before Congress is likely to cause an increase in demand of 30 to 40 million tons per year of compliance quality coal from Central Appalachia. This represents a doubling of this segment of the coal business. This paper will examine how this doubling can be met, what the likely implications for pricing are, the major uncertainties associated with these predictions, and the likely outcomes of the growth in compliance coal. Finally, some implications for fuel planners will be discussed.

Jan 1, 1993

Design models for belt conveyors used in mines predict both the belt power requirements and belt tensions. Conveyors with slightly downhill profiles are more complex to predict due to the way that models such as CEMA interpret friction. Performance of a particular conveyor in relation to other conveyors in the same system requires an analysis of natural stopping times, braked times and take-up location. A review of CEMA-based PC models is presented for design of underground multi-flight belt systems.

Jan 1, 1995

By A. B. Mayer

A generic task summary for design and implementation of hydrogeology programs at open-pit mine operations is presented as a guideline for management. Rigorous assessment of the local and regional hydrogeologic system is necessary to plan dewatering activities and to address environmental concerns. Dewatering activities include calculation of dewatering requirements, design of dewatering systems and evaluation of dewatering-water disposal areas. Environmental concerns include calculation of dewatering and water-disposal impacts, mitigation of soil and ground-water contamination and acquisition of water rights. Three-dimensional numerical models are commonly used to support these analyses. A thoroughly developed hydrogeology program provides an interactive basis for dewatering feasibility decisions and for support of environmental permits and regulatory compliance.

Jan 1, 1993

By R. J. Miller

Mechanized Roof Supports (MRS) have dramatically improved safety and productivity of retreat pillar mining in coal. Due to low capital cost and greater flexibility, retreat panels have in some cases approached the productivity of a longwall. Because of improved safety and rapid set-up time when compared to conventional timbering, MRS are driving a return to retreat pillar mining in many situations. This paper describes how panel layout can be optimized for safety and operational efficiency when using MRS for retreat pillar mining of coal. The potential for significant unit cost reductions will also be addressed.

Jan 1, 1996

By U. Paschedag

Today&apos;s modern longwalls have to produce high outputs with maximum availability and running time with the additional requirement of ever increasing panel width and length high-performance face conveyors require intelligent solutions for the integration of drive systems and chain tensioning devices into the overall longwall automation. The fully automated chain tensioning system allows the operation of an AFC with optimum chain tension at all times regardless of actual load on the conveyor. For the heavy-load start-up, the accurate load-sharing and an efficient overload protection of modern AFC&apos;s WESTFALIA and Dodge jointly developed the integrated WB/CST drive system.

Jan 1, 1995

By Carl C. Martin

The treatment of ores in preparation for fatty acid flotation is characterized by a wide divergence in methods, and attempts to define "common practice", even for the same type of mineral, are usually of little value because of the numerous exceptions. Such factors as desliming, pulp density, pulp temperatures, and reagents for conditioning are successfully employed under conditions representing almost extreme opposites. More precise control of variables is necessary than with sulphydric flotation processes It appears likely that variations result from independent development of a process from the multitude of variables that characterize fatty acid flotation and the ores of non-metallic minerals. Consequently, a symposium is a suitable way of presenting a summary of pretreatment methods for fatty acid flotation processes, together with froth control practices, as they exist today.

Jan 1, 1959

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

By Donn W. Leva

In North America, pipelines move more material than any other form of transportation. 1 Pipelines have been used principally for the transportation of liquids and gases; however, slurry pipelines have made notable gains in recent years enabling solid materials to be moved efficiently by pipelines. The obvious advantages of pipe-lines --low maintenance, low operating costs, minimal impact on the environment, greater land use, low labor intensity, safety and high operating factor --have stimulated researchers in England, West Germany, Japan, USSR and the USA during the past ten years to develop pneumatic capsule pipelines for the movement of bulk materials in large quantities. As a result of this work, pneumatic capsule pipelines are now available for the movement of dense bulk materials. Through these pneumatic capsule pipelines, material is moved in wheeled capsules which are pushed through the pipeline by flowing air. In this paper, a capsule pipeline system developed by the Georgia Institute of Technology and Tubexpress Systems, Inc. of Houston, Texas is discussed. The Tubexpress System Major Components The pipe used for a Tubexpress capsule system is standard thin wall welded steel pipe. Since pressures in the system generally do not exceed one atmosphere, the controlling design criteria for wall thickness of the pipeline is pressure from the overburden of the backfill if the line is buried or the structural requirements for supporting itself and the load if it is suspended or supported on piers. The air pumping system for Tubexpress is a combination of

Jan 1, 1977

By T. McCallum, B. Wellbrook, T. Ratnaweera

"Pressure oxidation (POX) leaching of copper (Cu) concentrates continues to be explored as the next generation of leaching processes to sustain existing Cu Solvent Extraction/Electrowinning (SX/EW) operations as easily leachable ores become scarcer. The leach liquors produced, particularly from total pressure oxidation, contain elevated concentrations of Cu and acid, making solvent extraction processing more challenging. Addressing this challenge will require innovative processing techniques and continuous improvement to be successful in achieving satisfactory physical and metallurgical performance in the SX plant. The ability to efficiently process these feeds via SX plays an important role in the continued success of POX technology. Characteristics of a concentrate leach pregnant leach solution (PLS) are discussed, along with best practices that should be considered for processing by SX. Findings discussed in this paper will shed light on ways to reduce process risk and bring additional improvement to the industry with minimal change to the SX plant. INTRODUCTION Hydrometallurgical processing of copper concentrates continues to gain interest from the industry. Treatment by smelting and electro refining continues to dominate, accounting for ~80% of global copper production, but is faced with its own challenges. The case for increased hydrometallurgical processing has been discussed as high grade ore deposits are diminishing, capital costs for smelting are high, and the environmental aspects present challenges for sustainable practice. The hydromet copper industry is also turning a corner as easily leachable copper oxide deposits are depleting, and excess SX-EW capacity exists in certain regions. The transition to hydrometallurgical processing of copper concentrates will take a bit of effort as leaching of copper sulfides is difficult and byproduct credits must be considered. Various POX leaching processes have been studied and proposed to the industry as viable practices. Of the many processes, commercial use has been practiced with the Mount Gordon Copper Process, total and partial pressure oxidation by Freeport-McMoRan at their Bagdad and Morenci, Arizona complexes, the Sepon Copper Process in Laos, and the bioleach BIOCOP™ process in Chile. The experience related to the current paper centers around Cu concentrate leaching performed by Freeport McMoRan (known as CLP). The patented process was developed as an alternative to smelting and refining in 1998. The technology applies to both molybdenum and copper concentrates. Commercial CLP research and development began with Phelps Dodge in 1999 to 2001. The first commercial plant was commissioned in 2003 at the Bagdad operation. Initial operating conditions of the Bagdad CLP were under high temperature conditions before converting in 2005 to medium temperature conditions. In 2007-2009, the CLP technology was commissioned in Morenci, operating medium temperature and high temperature lite conditions until shutting down due to the economic downturn. The Morenci CLP restarted operation in April 2015 due to acid production benefits for the Morenci leach operations. Renewed solvent extraction test work initiated well before restart and has been an ongoing focus for further SX plant optimization."

Jan 1, 2018

By Surendra K. Mishra

With increasing regulatory pressure from the environmental authorities, waste management has become a focal point of industrial operation. To offset the waste management costs, industry has made conscious effort to recover usable resources from the waste streams. This paper reviews the technical developments and current practices in processing of waste materials. Methods for recovering metallic, non-metallic and organic species from solid wastes and effluents generated by operating plants are discussed.

Jan 1, 1997

By Frank Florez

INTRODUCTION The Magma mine, located at Superior, AZ, some 100 km (60 miles) east of Phoenix, was discovered in 1875, and was originally mined for silver. The property was acquired by W. B. Thompson who formed the Magma Copper Co. in 1910. Prior to 1965, square-set mining and cut-and-fill methods were used to mine steeply dipping veins at Magma. Ore was moved to the chute by gravity in the square-set stopes and by slusher in the cut-and-fill stopes. The stopes were gobbed with waste from the surface and development headings in the mine. The original square-set method of mining was modi¬fied in order to extract replacement ore bodies in limestones that dipped at 0.52 rad (30°) and varied in thick¬ness from 4.6 to 38 m (15 to 125 ft). Mining of these ore bodies was done by starting at the upper lateral ex¬tremities and retreating to the access openings. The timber square sets and cribbing were used as temporary support, the ground being allowed to cave as the mining retreated. It was found, however, that mining in such a manner was very inefficient; safety hazards increased be¬cause of the blocky and fractured characteristics of the ore and the weakness of the hanging wall. GENERAL DESCRIPTION The undercut-and-fill method of mining is now the primary stoping method used at Magma, and no pillars are left for later extraction. Four ore bodies are pres¬ently being mined. These ore bodies (see Fig. 1) dip conformably at 0.52 rad (30°) to the east with the host limestone and shale sediments, their average strike length is about 122 m (400 ft), and their thickness varies from 9 to 38 m (30 to 125 ft). The ore bodies are separated by varying thicknesses of barren rock. Three of them come together at various elevations primarily in the area of the main feeder fault, but there is an apparent horizontal displacement of about 23 m (75 ft) on the main feeder fault which complicates stope layout. The method as originally applied has been modified in order to mine more efficiently ore bodies that are 9 m (30 ft) or more in thickness. The modification was made to mine all the ore at a given elevation before dropping down for the cut below. The advantage of this is that mining is done on a horizontal plane and there¬fore muck removal can be mechanized. Also multiple faces are made available, thereby improving overall min¬ing efficiency. Another major change made was to carry a 6.7-m (22-ft) face when mining the top sill and a 6.4-m (21-ft) face when mining under fill rather than the former standard 3.35-m (11-ft) high face. This change lengthens the mining cycle and cuts mat prepa¬ration costs in half. Stopes are laid out (see Fig. 2) so that maximum mining panels are available and yet one stope crew will not tie up too much of the ore reserve. One stope might consist of as many as 20 panels, and these panels are divided evenly on opposite sides of the extraction cross¬cut. The stope layout is planned so that the maximum tramming distance to the orepass will not exceed 30.5 m (100 ft) on the crosscut and 38 m (125 ft) in the panel. Stope panel distances are sometimes exceeded when min¬ing to the extremity of the ore body. Tramming distance limits are determined by the efficiency of the com

Jan 1, 1982

By Santhanam Sundaram

The potential for the utilization solar energy for the production of industrial process steer in mineral processing industries is discussed briefly. To advance the technical and economic feasibility of solar-thermal systems applications, U.S. Department of Energy has funded several projects. NL industries of Newberry Springs, California is one among them and has been chosen as a case study. The NL Industries solar system consists of 950 square meters of Del, single-axis, tracking, parabolic-trough, concentrating collectors. It was designee to produce a portion of the 420°. 530°k. steam utilized in a trying operation reduce the moisture content of hectorite ore from 10 percent to 4 percent. (Hectorite is an hydrous magnesium silicate which, when refined, is of significant commercial interest because of its applications in various chemical and food processes.) is estimated that implementation or this solar system could result an annual savings of 3.545 billion KJ ,3.360 billion BTUs), or the equivalent of 90 cubic meters (600 barrels) of oil and a net reduction of 1,860 kilograms (4100 pounds) of air pollutants annually. The technical, economic and institutional issues encountered in the course of this project are also discussed. Finally, the impact of the commercialization of solar energy applications in mineral processing industries is evaluated.

Jan 1, 1981