Search Documents

By Louis W. Cope

The Compañía El Zapote Yacimiento Y Minas, S.A. has an ore body containing 650,000 tons of 0.185 oz/t gold ore in Mexico. Metallurgical testwork has been done to determine the response of this ore to several possible processing schemes. The paper describes the rationale for selecting the Silver State Mining Co. methods in Colorado. Plans for developing the mine and building the treatment plant are described in detail in the paper. Estimates of capital and operating costs are included.

Jan 1, 1984

By Zhang You-di

A comprehensive model has been set up for surface mine long range planning. It is a system simulation model based on the oriented graph theory. Via this model, a series of mining results such as mineral and waste volume, mineral quality, mining intensity, material haulage distances, dumping area parameters and mining coat for different mining alternatives, can be derived and optimized. This model has been applied to 37 mining alternatives in several surface coal mines and proved mathematically correct and results reliable.

Jan 1, 1986

By W. Z. “Ben” Wu

The investigation provides a method of efficiency evaluation among several kinds of tools employed to cut different types of rocks. A ballistic test stand incorporated with a modified Hopkinson bar was used to simulate a percussive drilling tool. An Apple IIe microcomputer was employed for high speed data acquisition and numerical analysis. A newly developed method for remote monitoring the rock-tool interaction, including contact force, bit penetration and energy transmission,is presented in the paper. Theoretical predictions and experimental results appear in faily good agreement

Jan 1, 1986

By William J. Maloney

Blind drilled shafts are becoming increasingly popular as a secondary and sometimes primary means of ventilation. This is particularly true in the Appalachian coalfields. Some reasons for the rebirth of blind shafts are economics, timeliness, safety characteristics and their inherent independence from underground operations. Blind drilling has had limited use in hard rock and tunneling ventilation. Advances in cutters, bit design, equipment and lining systems have made blind drilled shafts the shaft construction technique of choice for ventilation specialists. History of blind drilling Blind drilling's roots include the Nevada test site, the coalfields of Appalachia and Germany, and the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin. Shafts completed by oilfield equipment ranged from the shallow 1.5 and 1.8 m (5 and 6 ft) lined shafts on the Nevada test site to two 3 m (10 ft) lined, 222 m (730 ft) deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths. The record, completed in 1969, is a 2.28-m-diam (90-in.-diam), 1875-m (6150-ft) deep shaft, located in the Aleutian Islands of Alaska.

Jan 1, 1993

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

Hydrodynamic investigations in exploratory boreholes and grouting holes are conducted for the purpose of obtain¬ing information about the hydraulic properties of the hydrostratigraphic section to be intersected by the proposed underground workings. The information obtained from the investigations provides the basis for calculating the hydrau¬lic coefficients of fractured permeable rock, the dimensions of the anticipated grout isolation curtain(s) around the un¬derground workings, the number and location of grouting holes, the injection pressure modes, and also the volume(s) of grout that will be required (Anon., 1976, 1978). The following data on each aquifer are obtained from the investigations conducted in monitoring and grouting bore¬holes and the analysis of the results: 1) the top of each hydrostratigraphic unit, 2) the thickness of each unit, 3) the ground water fluid potential distribution in each unit, 4) the coefficient of permeability, 5) the piezoconductivity, 6) the fracture porosity, 7) the geometry of the fractures in the rock, 8) the elasticity-compressibility coefficient of the fractured rock, 9) the chemical composition of the ground water, 10) the direction of flow of the ground water, and 11) the expected inflow rate of water into the shaft, drift or tunnel. STG uses its DAU-3M type flowmeter to conduct in¬vestigations of directions of flow in vertical, inclined and horizontal drillholes. The DAU-6 instrument is used to de¬termine the direction of flow of ground water in each frac¬ture or fractured aquifer. Various singular and double DAU type packers are used for pumping and for injection studies (tests) and for flowmeter investigations. Normally the instruments enumerated above permit in¬vestigations to be conducted in each separate aquifer with¬out reinforcing the holes with casings. On the basis of these investigative data, both the hydraulic properties of unfractured rock and the hydraulic properties of the fractured rock are estimated. Dual porosity rocks require special attention because they tend to segregate the grout. 3.1 FLOWMETER INVESTIGATIONS IN BOREHOLES The STG flowmetric methodology is based on the mea¬surement of the ground water flow rate through the borehole by hydrostratigraphic interval after the disturbance of the hydrostatic equilibrium in the "hole-aquifer system" (after pumping or injecting). The relationship of the head changes to the discharge into or from a particular hydrostratigraphic unit obtained during the tests serve as the basis for calcu¬lating the hydraulic properties. Flowmetric investigations facilitate the determination of the number of aquifers, their depths, their thickness, the hydraulic properties of the fractured rock and the magnitude and direction of the flow of ground water. 3.1.1 FLOWMETER HARDWARE STG conducts flowmetric investigations in boreholes using its DAU-3M-108, DAU-3M-73, DAU-3M-57 and DAU-3M-44 instruments.' They have respective external diameters of 108, 73, 57 and 44 mm. The type of flowmeter selected for use depends on the borehole geometry and the technological scheme for carrying out the investigations. Boreholes with a drilling diameter of 76-93 mm are inves¬tigated with the DAU-3M-73 flowmeter; boreholes drilled by bits with a diameter of 112 mm and more are investi¬gated using the DAU-3M-108 flowmeter. The DAU-3M¬108 and DAU-3M-57 instruments are used for flowmetric investigations with a packer. 3.1.1.1 The Downhole Sensor The sensor design of the DAU-3M-73 hole flowmeter is shown in Fig. 2. The design of the DAU-3M-108 instru¬ment is similar to the design of the DAU-3M-73 instrument. The frame of the flowmeter sensor shown in Fig. 2 consists of a casing, an upper and lower centering mount and two rings to which the guiding rods are attached. The upper rods are built into the connector bushing; the lower rods are built into the coupling sleeve. The borehole cable is attached using a half-coupling, a packing ring and a constriction nut. Thus, the frame of the flowmeter sensor is made so that the free passage of water to the impeller is facilitated along with the necessary rigidity. The primary moving component of the flowmeter is the double-bladed impeller, which rotates on cobalt-tungsten pivots and agate thrust bearings. Special extended air cham¬bers protect the supports of the impeller from the action of the borehole fluid which may contain fibrous and abrasive particles. The air located in the chambers shields the sup¬ports from direct contact with the borehole fluid when the sensor operates in a borehole. The hollow casing of the impeller serves the function of a lower cap. The upper cap is attached to the casing using a threaded connector; it is affixed also with a lock-nut. An adjusting screw with a

Jan 1, 1993

By Robert M. Rowe

Among the increasing operating costs affecting today' s processing facilities are those necessary in meeting the continually growing requirement for safe and environmentally sound materials- control and handling procedures. Of particular interest are materials listed as hazardous, the need to maintain accurate records of their acquisition, consumption and disposal, and the obligation to employees and the community to have information available regarding such materials. Some requirements affecting modern operating facilities are reviewed in this paper, and potential methods for dealing with complex handling and documentation requirements, including computer automation, are discussed.

Jan 1, 1991

By C. Widham

Introduction It is generally accepted as dogma that sampling contributes most of the error in gold fire assays. Differences in assay results on pulps from the same sample interval are frequently regarded as evidence of the presence of the so called "nugget effect" of relatively coarse gold particles. It is true that coarse gold particles can contribute to substantial sampling fluctuations. But, while the process of sampling is probably the major source of error, the analytical process cannot be completely ignored as a possible contributor to erratic assay results. To maintain a stable assay process, the analytic part of the system must also be kept in control. One method of monitoring the performance of the analytic system is to systematically assay standard materials, whose sampling characteristics are carefully controlled. Gold assay standards are not prepared, nor can they be prepared, to account for both sampling and analytical errors. It is not possible to send coarse material to a lab for both preparation (i.e., comminution and splitting) and fire assaying and then come to conclusions only about the fire-assay process. Because most gold ores are very heterogeneous, sampling errors would, in most cases, completely mask the contribution of the analytical errors. Assay-standard material is prepared only to assess the accuracy and variability in the fire assay process. Because the objective of the assay standard is to provide information about the fire assaying, it is necessary to control the sampling error of the standard material, so that it is only a minor constituent of the discrepancies observed in any assay results. To do this requires that the particle size of the standard material be reduced to a point where the relative standard deviation of the sampling error (i.e... the standard deviation of the errors divided by the average gold content of the material) is 2% or less. For all but very homogeneous mineralization, this means that the material must be reduced to 100% -150 mesh before the sampling errors are adequately controlled. However, even reducing the particle size can contribute to sampling problems. The liberation of gold may cause segregation that can cause large sampling fluctuations that are not easily controlled while maintaining the desired grade. Because, in most cases, the standard material would already be in the "pulp" state when it is submitted to a lab for assay, it is not possible to entirely conceal the nature of the sample from the lab. This is a problem inherent in using assay standard material. Because of the contribution of sampling to error generation in the assay process, the use of "coarse" material does not solve the problem of submitting a totally "blind" standard to the lab. In the sections that follow, the selection, preparation, testing and use of gold fire assay standard material is discussed. While some may dismiss the production of standard material as folly, it is possible to produce and utilize standard material to stabilize and improve the fire-assay process to produce more reliable assay results. Material selection It is desirable to use material that has as nearly the same metallurgical characteristics as the samples with which the standards will be included. However, this is usually difficult. For many reasons, including the particle size at which a significant amount of the gold mineral is liberated, the sampling characteristics of even -150-mesh material may preclude the use of geologically and metallurgically similar ore as a standard. It is usually easier to get material having desirable grade characteristics with the necessary sampling properties than it is to find geologically and metallurgically similar material with the required sampling characteristics. High-grade standards are especially difficult to find and prepare. This is because, as grade increases, the size of the gold particles usually increases. Larger gold particles are liberated and tend to segregate during comminution, and the homogeneity of the material cannot be maintained. For grades much above 3 g/t (0.088 oz/ton), it is very difficult to find material that has the proper sampling properties. Old mill tailings are likely candidates for assay standards. Some of these have sufficiently homogeneous mineral contents, so that the sampling errors can be effectively controlled. Where mill tailings are either not available or are not acceptable, mineralization that has exhibited homogeneous results in reassays of the pulp material is also a good candidate for the standard. Finally, the mineralized rock being sampled may (and should) be used if adequate homogeneity in the -150mesh material exists. "Adequate" ("acceptable") homogeneity is defined below.) It is important to use standards having a wide range of grades. This alone may preclude the material being

Jan 1, 1997

By Michael S. Robinson, Serge Moalli

Construction of the CSO Retention - Treatment Tunnel, Segment 1 in Dearborn, Michigan includes excavation for an overflow Structure with a minimum inside diameter of 15.24 m (finished). The excavation extends downward through overburden soil including a 15.2 m thick zone of potentially weak clay. This paper presents the subsurface data for the clay and a geotechnical analysis thereof, together with predictions of the behavior of the planned 15.54 m inside diameter open end caisson as it is sunk through this potentially weak zone. In a companion paper, the writers will compare the behavior observed with that predicted.

Jan 1, 1995

By P. E. Sperry, J. M. Duncan

INTRODUCTION The purpose of the report on which this paper is based is (1) to evaluate the potential for cost reduction of urban mass transit tunnels by use of alternative materials transport systems during the tunneling process, and (2) to identify research and development program elements to assure that the materials transport system will not become the limiting factor for the rate of excavation. The approach taken was: Review the state of the art of urban tunneling by extensive interviews with representatives of tunnel contractors, equipment manufacturers, government agencies and consultants, and by review of recent literature.

Jan 1, 1979

By M. C. Rockwell, G. F. T. Lay

Promising placer gold exploration sites offshore Lunenburg County are drowned pre- and post-glacial river channels and auriferous glacial tills. Gold values up to 5.67 9/m3 have been encountered in the vicinity of the Ovens Peninsula offshore Lunenburg County. Moderate gold values associated with notable amounts of heavy minerals were reported from various other exploration sites in this area. This paper highlights the major geological and gemorphological features for placer gold depositions in southern Nova Scotia. The past to present gold exploration activities nearshore and offshore Lunenburg County are summarized and potential areas for placer gold identified.

Jan 1, 1988

By C. B. Manula

A method for the feasibility assessment of open-pit operations using conventional shovel/ truck systems to mine steeply pitched coal seams has been applied at The Pennsylvania State University. Three computer models were developed for the analysis: a geology and reserves model (GEOL), an open-pit materials handling simulator (OPMHS), and a cash flow model (CASH) (Manula, Albert, and Burgos, 1976). GEOL provides the basic mining data; OPMHS simulates shovel/truck performance related to pit profiles and average mining locations to provide productivity rates needed to size the system; and CASH provides either a selling price or rate of return (ROR) for the product. The general flow of information generated by these models is shown in Fig. 1. Since the ratio of overburden-extracted to coal-produced places a definite economic limit upon a mining venture, geological data must be analyzed with the least possible manual effort to minimize computational errors. This is especially true if the property contains several seams that are steeply pitched. In this situation, a computerized analysis is by far the most efficient and effective method to determine coal reserves and waste tonnage. This chapter describes the reserve model developed at Penn State and provides an example to demonstrate its application.

Jan 1, 1979

By G. T. Adel, W. Z. Choi

In previous work at Virginia Tech, a population balance-model describing the simultaneous processes of size reduction and mineral liberation has been developed. Experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple-composite- class model has been developed. Emphasis is placed on direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

By R. K. Mehta, G. T. Adel

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated far a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1991

By J. E. Rourke, O&apos

This paper describes the use of rock index property testing to obtain rock properties that a.re useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include (1) point load; (2) Schmidt hammer hardness; (3) abrasion hardness; and (4) total hardness. The first two index properties correlate to uniaxial compressive strength and Young's modulus. Discussions are given on the relationship to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The latter two properties correlate to construction performance parameters and some experience is cited. Examples of data are presented from an index testing program carried out on siltstone, sandstone and limestone rock core samples from a deep borehole drilled in the Paradox Basin of Utah for a nuclear waste repository site investigation.

Jan 1, 1988

By S. Frimpong, N. Demirel

Overburden excavation is an integral component of the surface mine production chain. The walking dragline is the most economic production equipment for overburden excavation in strip mining. Draglines are capital intensive, and thus, investments in multiple units severely impact the economic viability of projects. The use of few dragline units results in highly concentrated production focus, which must be efficiently managed to derive the potential economic benefits. Efficient use of draglines requires a thorough knowledge of the powered functions, the 3D rotational and translational motions and machine-formation interactions within the operating environment. Dragline kinematics and dynamics are required to understand and characterize machine performance and efficiency. In order to sustain the high productivity in difficult operating conditions, the dynamics of the dragline must be modeled and analyzed based on comprehensive kinematics. This paper investigates the planar kinematics of the front-end assembly and its interactions with the formation during excavation using the “Vector Loop Analysis” formulation with comprehensive simulation modeling in MATLAB Simulink. The kinematic models are used to examine the translational, rotational and angular displacement, velocity and acceleration components of the dragline front-end assembly along defined bucket trajectories during excavation. The results are the precursors for comprehensive modeling to examine the load deformation, torque requirements and dragline stress loading profiles for improving machine health and longevity.

Jan 1, 2006

By H. E. Goetzman

A cooperative research project supported by the taconite industry and the Minnesota DNR was undertaken to establish quality standards for carboxymethyl cellulose (CMC) based organic binders. The objective of this study was to identify the effect of CMC quality parameters such as degree of substitution, molecular weight, and purity as well as the effect of inorganic extenders such as sodium carbonate on performance. These factors have been evaluated by green-ball testing with two taconite concentrates followed by pot-grate tests. Balling tests with bentonite and Peridur were conducted to provide baseline data. At a constant DS the molecular weight as measured by viscosity had the greatest effect on green-ball drop strength. Dry-ball compression strength was most dependent on CMC addition rate and sodium carbonate content. DS was not found to have a major effect on green-ball quality for medium molecular weight CMC.

Jan 1, 1988

By S. S. Hsieh

As part of a program to address long-term needs for ensuring adequate supplies of domestic phosphate raw materials, the Tennessee Valley Authority (TVA) has conducted considerable research on dolomitic phosphate rock beneficiation. The discovery that alkyl diphosphonic acids act as phosphate mineral depressants led to the development of several processes involving a carbonate flotation step for the effective beneficiation of these problem ores. Most recently, a partial de-oiling process in which the reagent consumption is greatly reduced has been developed. The reduction is achieved because part of the initial feed is beneficiated without passing through the separate carbonate flotation step. Using this method, a phosphate product containing 30.6-30.9% P2O5 and 0.7-0.8% MgO was obtained from a Florida dolomitic phosphate pebble which contained about 23% P2O5 and 2.0% MgO. The P2O5 recovery was 80.8-86.5%.

Jan 1, 1989

By Karl J. Benecke

Though the first patent on a bucket wheel excavator was granted in 1881 in the U.S. this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with the development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generating, despite the low heating value of German lignite in the order of 8500 kJ/kg (3600 BTU/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is in the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output open pit mines. The largest one, Fortuna Mine in the Cologne district, produced a, total of 45 000 000 t lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95 200 000 bank m3 equal to 200 000 000 t overburden had to be removed to accomplish this lignite output. The largest BWE (Fig. 1) ever built is working in the Fortuna Mine, too. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 t, its wheel diameter 21.6 m, as high as a 7-storey building.

Jan 1, 1977

By John W. Conn, Harry C. Verakis

An explosion in an underground coal mine can have a devastating effect on the main fans used to provide mechanical ventilation. The Code of Federal Regulations, Title 30, Part 75.310 (CFR, 1992), specifies that each main mine fan shall be offset by at least 15 feet (4.6 m) from the nearest side of the mine opening unless an alternative method of protecting the fan is approved in the ventilation plan. Also, each main mine fan shall be protected by one or more weak walls or explosion doors. This paper presents venting and fan configuration designs which provide a comparable degree of safety for explosion protection. Design flexibility is enhanced and a means for consistency in safety judgements is afforded.

Jan 1, 1993

By Alan P. Cook

Methane levels have been measured around continuous miners and compared with computer simulations of methane flow. A multi-channel data logger, reading continuously from six methanometers, has shown methane levels to vary at different positions around a continuous miner, with the cutting drum and the immediate face area not necessarily recording the highest concentrations. Methane levels in the driver's cabin are generally low compared with the return side. Computer simulations, using computational fluid dynamics, have been supported by the measured data, and have shown that methane behaviour within the first few metres of the face varies considerably for different bord and pillar development stages. Methane is diluted rapidly to acceptable levels, but the distance required for this is extended when ventilation flow to the face is restricted.

Jan 1, 1995