Search Documents

By William K. Brown

Are the results of an exploration program worth the cost? This is a question I suspect many of you are familiar with and, theoretically at least, it is an easy question to answer. The answer, of course, lies in comparing the future earnings stream the program is expected to generate, to the present value of the cost of carrying it out. While historical costs can be determined without much difficulty, estimating the value of a future earnings stream involves all sorts of assumptions regarding future costs, metal prices, inflation rates and an appropriate discount factor; and in the context in which the question arises, requires additional assumptions about mineral deposits which have yet to be discovered. As a practical matter, this kind of approach isn't likely to produce a very convincing answer; certainly not one convincing enough to satisfy a skeptical audience; nor one likely to temper the illusions of recent converts to mineral exploration, who are convinced that if enough money is spent, profitable discoveries will inevitably follow. Within broad limits, however, I believe it is possible to analyze the costs and results of gold exploration in the U.S.A. over the past 20 odd years in a useful manner. And while such an analysis is imperfect, it will provide some insight into this fascinating subject.

Jan 1, 1983

By Salvatore] [Parand

Deep well disposal is a much used and abused term which is the panacea for wastewater disposal in some minds and creates near hysteria in others. It can be the answer to a difficult waste disposal problem, or if improperly employed, can create more problems than it solves. My purpose in this presentation is to focus on the value and limitations of deep well disposal as expressed by New York State's experience and policies. To he sure, I feel a place for such practices docs exist if adequate safeguards are utilized. I shall give a broad brush approach to New York's legislative, geologic and operational concerns and speak briefly on some case histories. I shall not delve deeply into the technological details since I am not an expert in mining exploration or well drilling.

Jan 1, 1973

By Cyrus W. Field

Chemical, mineralogical, and petrographic data have been obtained for suites of plutonic rock samples from the Guichon Creek Batholith of British Columbia and the Mineral-Iron Mountain-Sturgill Peak- Cuddy Mountain-Peck Mountain areas of western Idaho. Intrusions at these two geographically separate localities represent composite plutons ranging from early gabbro through quartz diorite to late grano- diorite and more silicic-alkalic phases. They are early Mesozoic (200 m.y.) in age, and contain porphyry-type mineralization in close spatial and temporal association with late-stage intrusions of porphyry, aplite, pegmatite, and (or) breccia. Country rocks are eugeo-synclinal assemblages of metasedimentary and metavolcanic greenstones of Permian, Triassic, and Jurassic age. The petrochemical evolution of these intrusions, and the effects of subsequent hydrothermal alteration and metallization, are illustrated by standard ternary diagrams of the major oxide and mineralogical data. Samples plotted on an AFM diagram suggest a calc-alkaline magma trend. However, their distributions on NKC and Qz-Kf-Pf diagram show well-defined trondhjemitic (Na20-rich) and tonalitic (quartz-rich) variants to this trend, which are similar in part to those reported for mineralized island arc plutons of the northern Caribbean and southwest Pacific, but which contrast markedly to those for continental plutons of the Bingham District, Boulder Batholith, districts of southern Arizona, and elsewhere.

Jan 1, 1975

By Marvin A. Ph. D. Friedman

The following paper describes an overview of evaluations for assessing the potential hazards associated with handling newly developed reagents used in the mining industry. Important factors in determining the risk and hazard associated with handling a particular chemical include hazard identification, dose-response assessment, exposure assessment, and risk characterization. The hazard evaluation step involves collecting and evaluating appropriate toxicology information on a chemical. This can include a comparison of the structure of a developmental chemical with that of a material with known toxicology information. Acute toxicology data, including oral, inhalation, and dermal LD50 values, eye and skin irritation data and sensitization or allergic potential information are typically generated for new chemicals. Environmental and in-vitro genetic toxicology data (e.g. Ames test) are also used to evaluate new mining reagents.

Jan 1, 1994

By William J. Kohan

Milling has traditionally been considered more art than science. In the last 10 years, significant improvements in process equipment have been made and we are finally taking significant steps toward approaching grinding as a science. Two machines have been at the center of this development. These are the roll press and the high efficiency separator. The former can be considered as a new technology or adaptation of existing i.e. roller mill. The latter is clearly an improvement of existing technology. Other machines have been introduced to a lesser degree and later. Among these are the CKP and Horomill. The purpose of this paper is to provide an over- view of the currently available modifications for operating systems and options for new milling circuits with some comments on their application and history.

Jan 1, 1997

By Robert Roggenthen

In 1994, ASARCO's Mission Complex Mine Planning Department designed a new stripping schedule to take advantage of reserve opportunities. Based upon the new stripping design, overburden removal exceeded available hauling capacity. This increased hauling capacity requirement required that ASARCO consider alternative technologies for material transport. In 1997, ASARCO Mission Complex completed the purchase and installation of a 3.5 km, 8,600-tph conveyor system to transport waste material. The conveyor system is composed of two apron feeder/sizer units manufactured by Mining Machine Development LTD. and a conveyor system manufactured by Krupp-Robbins. This paper will review the option of truck haulage versus conveyor transport for overburden removal by (1) describing engineering studies contributing to the solution, (2) researching proactive options to create alternative management decisions, and (3) revealing final results of the project.

Jan 1, 1998

By K. Morsy, S. S. Peng

A new method of pillar stability evaluation was proposed. The unique feature about the method is that it estimates two types of stability factors for the pillar. The first stability factor is to measure how much the applied stress at that point is smaller than its strength, and the second stability factor is to predict whether or not the pillar will fail violently. The strain-softening behavior of coal pillars was simulated by the Drucker-Prager yield criterion. A new algorithm that simulates the strain-hardening behavior of the gob was used. A numerical technique to estimate the local mine stiffness (LMS) was introduced and verified by both numerical and analytical methods. A case of massive pillar failure in a room-and-pillar mine was used to define the stability limits for the proposed method.

Jan 1, 2003

By V. Carabias-Hütter, A. J. Basu

The paper aims at promoting sustainability assessment and reporting into practice using a globally acceptable set of guidelines and a common framework for internal and external reporting at a project/site level. Indicators are used for measuring performance, and this paper addresses development and implementation of performance indicators for sustainability assessment and reporting at local as well as global levels. The selection of a proper set of indicators is a challenging task. The indicators selected should provide the expected information for making right decisions. Relevant and credible sustainability reporting supported by a consistent performance indicator system can be the starting point for benchmarking environmental and social performance for the natural resources sector.

Jan 1, 2004

By R. H. King

The US coal industry has been using continuous room-and-pillar mining (CRPM) machines for more than 30 years for longwall development. This equipment has also been used for production mining in areas that are not appropriate for longwall mining. From 1977 to 1987, the portion of annual US production mined by continuous miner (CM) sections grew slightly from 65% to 70%. Over this time, mine operators and manufacturers have made some advances to attain the full production potential of this method. This is evidenced by the fact that average tons per eight hour shift for continuous miners in the US grew from 180 t (200 st) in 1977 to 431 t (475 st) in 1987. The authors (1990) reported that the increase in productivity was due to several factors: • a drop in prices; • a more mature workforce; • union stability and incentive programs; •procedural improvements; and •technological advances. The authors estimated that about one-third of the increased production came from the first three and other unaccounted for factors and one-third each for the last two. Even though improvements were considerable, continuous miner capacity is much higher than 431 t/shift (475 st per shift). For example, the machinery is capable of mining more than 9 t (10 st) per machine for the 6.5 available hours per shift or 3.5 kt (3900 st). However, this has never been attained on development. The averages of most mines are less than 900 t/shift

Jan 1, 1991

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015

By David B. Ashley

Risks in underground construction are often viewed as technical in nature; "running ground, " "squeezing ground" and "chimneys" are terms that appear in construction managers' nightmares, and occasionally in their underground projects. Financial consequences of these and other project risks are reviewed. Special attention is paid to sources of cost overruns. From this study a structure evolves for setting priorities for risk management actions; these actions can also be tested for impact and potential effectiveness. Finally, case study reviews of six underground projects indicate the "state of the practice" for financial risk management.

Jan 1, 1983

By L. Cui

X. Huang (1997) recently suggested a poroelastic model for simulating the hydraulic fracturing breakdown pressure. His paper began with a discussion questioning Haimson and Fairhurst's (H&F) model. He claimed that the H&F model failed to lead to the Hubbert and Willis (H&W) model as[ a --> 0.] Huang also tried to explain why the H&F model could only work for special types of rock conditions. He pointed out that one possible reason could be that the Terzaghi's effective-stress concept had been adopted. The H&F model (Haimson and Fairhurst, 1969) was derived under the conditions that the borehole wall is fully penetrated (pp = pi) and a drained state is realized (steady pore-pressure field). Cui et al. (1997a) demonstrated that, under drained conditions, the total stresses in the penetrating poroelastic model (identical to the H&F model) degenerate into their counterparts in the elastic model (identical to the H&W model) as [a -- 0.] However, the effective-stress conditions are different for both of these models, because different pore-pressure conditions at the borehole wall were adopted. In the H&W model, p = po was assumed, i.e., the pore pressure field is not disturbed; but pp = pi was assumed in the H&F model. Assuming that Terzaghi's effective-stress controls tensile failure (that was the hypothesis adopted in both the H&F and the H&W models), only the following two special drained poroelastic cases may degenerate into the H&W model for very small a: • when the pore pressure at the borehole wall remains at the same level as the virgin pore pressure for a penetrating model and when the borehole wall is simply impermeable (i.e., the nonpenetrating model, Cui et al., 1997b). Therefore, simply setting a = 0 in the H&F model generally does not lead to the same problem described by the H&W model. On the other hand, when the porepressure boundary conditions do not correspond to the ones in the H&W model, a degeneration of the poroelastic model to the H&W model as [a – 0] should be questionable. The pore pressure at the borehole wall is generally dependent on the injection-fluid pressure and the penetrating conditions at the borehole wall, such as the existence of a filter-cake. For an impermeable wall, pp is independent of Pi, and it is basically an unknown [(how¬ever, pp -- po as t --oo).] For a fully permeable wall, pp is the same as Pi. Between these two extremes, pp should be a function of p; and the permeable condition of the borehole wall, which may be dependent of the leak-off coefficient cf. (the range of cf is from 0 to 1). Theoretically, for a rock with low permeability, a penetrating borehole wall is still possible. For saturated porous materials with very low values of a, poroelasticity shows that a pore pressure will be built up due to the stress concentration subjected to a nonhydrostatic in situ stress field (Cheng et al., 1993). This phenomenon is known as the Skempton effect. The variation of the pore pressure may be evaluated by [AP = 3 B(A rr + 06ee + A (Y,,)] (1) where B is the Skempton pore pressure coefficient. This pore pressure variation dissipates as time increases (it is totally gone as the drained state is approached). The rate of the dissipation mainly rely on the permeability of the formation. The dissipation is very slow for tight formations because their permeability is very low, and it is fast for rocks of high permeability. According to our analyses, the time period for this process could be from seconds (for sandstone's) to a couple of days (for stales). One possible reason that the H&C model did not agree well with the experimental results for rocks with low permeability might be that the time interval between the application of the loading and the fluid injection had not been long enough for the dissipation of the Skempton effect. The effective-stress law basically defines how much pore pressure contributes to the total stress. The difference between Terzaghi's effective stress and Biot's effective stress is that 100% of the pore pressure contributes to the total stress in Terzaghi's definition, while only a certain portion of the pore pressure ((ap) goes to the total stress in Biot's definition. Therefore, when the pore pressure at the boretole wall (pp) is determined according to Biot's effective-stress law, app in the total tangential stress is attributed to the pore pressure. In other words, Terzaghi's effective tangential stress is expressed

Jan 1, 1999

By Mark J. Dowiak, Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980s. About 45 Mt of hazardous wastes are produced yearly. One major aspect of the problem is the siting, design, and construction of' environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sites for several reasons. • Surface mines offer an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic, savings when compared with sites on undisturbed lands that might require extensive excavation or embankment construction. • Surface mines often have an abundance of mine spoil available that could potentially serve as construction material. This could result in a significant economic advantage over other sites that might require extensive amounts of construction material to be excavated or hauled in. • Operation of a commercial disposal facility in a surface mine can reduce or totally alleviate reclamation costs. • For an abandoned surface mine, conversion into a disposal facility could represent a positive form of land use and may provide a means for reclaiming lands that would otherwise remain unreclaimed. Despite these positive reasons, there are many technical factors associated with surface raining that can make the prospect of disposal site development an uncertain one. Before discussing factors associated with mining that can present siting, design, or construction problems, some understanding of the basic components of a chemical waste disposal facility is necessary.

Jan 2, 1981

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and concrete is described. Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fast-opening valve discharges the compressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh -pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard, massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited.

Jan 1, 1998

By S. G. Axen

Design of wells for in-situ leaching is based on individual mining operation and ore deposit requirements. Major design considerations are well flowrate, depth, fluid composition, expected well life, mine operating plan and cost. A large variety of downhole equipment, materials of construction, contract services and methods of well completion and stimulation are available. A generalized design procedure which allows the engineer to optimize well design for a particular ISL application is described.

Jan 1, 1988

By John A. Shuster

INTRODUCTION Controlled ground freezing for mining and construction applications has been in use for over a century. Despite the great technological evolution which has occurred during this period, ground freezing is still used on projects today with much the same basic technology as that used originally over 100 years ago. Major developments have occurred in the separate fields of frozen soil mechanics, refrigeration, and heat transfer analysis. However, except for a few projects in Europe and Asia, these developments have not been combined to upgrade ground freezing techniques to their potential level. In view of this situation, it is believed desirable to examine the art of ground freezing in light of recent technical developments, together with highlights on some of the apparent advantages, disadvantages and economics of the various alternative approaches. The purpose of this paper is to attempt such an examination, with particular emphasis on the practical application of presently available technology. GENERAL ADVANTAGES AND DISADVANTAGES Ground freezing may be used in any soil or rock formation, regardless of structure, grain size or permeability; however, it is best suited to soft ground rather than rock conditions. Freezing may be used for any size, shape or depth of excavation and the same physical plant can be used from job to job despite wide variation in these factors.

Jan 1, 1997

By Allan D. Fernie

Growing interest in pit crushing and conveying is evident from the many articles, technical papers, and new equipment development recently presented. Application of a pit crushing and conveying system is complex, as many factors such as mine design, production scheduling as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1983

By M. J. Lowe

National Institute for Occupational Safety and Health (NIOSH) studies show that 43.5% of surveyed coal preparation plant workers had noise exposures exceeding the Mine Safety and Health Administration Permissible Exposure Level. Sound levels around vibrating screens in these plants often exceed 90 dB(A). NIOSH is currently developing noise controls for horizontal vibrating screens. To characterize noise sources, NIOSH researchers performed sound pressure level (SPL) measurements on a vibrating screen at their Pittsburgh Research Laboratory. The results show that the entire screen contributes to noise below 1 kHz and the vibration mechanism housings are most significant above 1 kHz. Constrained layer damping (CLD) treatments and an enclosure were used to reduce mechanism housing noise. These were evaluated using sound power level measurements according to ISO 3744. The CLD treatments reduced the A-weighted sound power level by 3.1 dB in the 1 to 10 kHz one-third-octave bands. A panel-on-frame vibration mechanism enclosure using various types of panels further reduced the A-weighted sound power level from the CLD configuration in the 1 to 10 kHz one-third-octave bands by 3.7, 4.0, and 3.9 dB for aluminum, steel, and Dynalam panels, respectively. The combination yielded a 7 dB reduction from baseline in A-weighted sound power for the same frequency range.

Jan 1, 2010

By E. J. Donovan, O&apos

The use of Dynamic Analysis techniques in the design of conveyor systems is extremely limited. The most frequent use of the technique is in large and expensive systems where the emphasis is on insurance against failure caused by catastrophic tension waves. This paper sets out to illustrate a much wider range of applications where dynamic analysis has been successfully employed. The examples chosen deal with identification and correction of dynamic low tension problems, the variability in take-up movement as other system parameters change, the requirement for proper tuning of starting controls and finally the absolute necessity for a complete understanding of the entire system when specifying brakes for critical applications. The intent of the paper is to get designers to view a conveyor as a system of interacting flexible components rather than as a single rigid body.

Jan 1, 1993

By K. C. Carriere

INTRODUCTION The purpose of this paper is to introduce the reader to basic control strategies for solid/liquid separation in mineral processing and to indicate some of the implementation difficulties to be encountered, without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with control systems and with dewatering processes, since exploration of these topics would require considerably more length. The paper is organized into three parts: first a general discussion on the need for control of dewatering processes and of the general criteria involved, next a more detailed elaboration on control strategies for the various unit operations, and finally a case study showing a specific approach towards such a project. Motivation & Objectives The justification for implementing any control system in an industrial plant is to improve operations and thereby to increase profitability. Without this motivation, the system will likely be perceived as unnecessary and will decline into disuse, an expensive and troublesome monument to someone's ill-conceived ideas. However, when a control strategy is correctly conceived, implemented and integrated into operations, it can provide significant advantages in operating ease and efficiency, and a handsome return on investment. In general terms, the objectives in establishing a control system are: • stabilization of process disturbances maintenance of product quality • maximization of throughput • dearer definition of process • protection of personnel and equipment A successful control strategy must address at least some of the above criteria. However, the most important requirement is a commitment on the part of plant personnel and management to start up, operate and maintain the system, and to upgrade it to reflect current process status and operational philosophy. Process Applications In this paper, control strategies will be explored for the most common methods of dewatering of mineral pulps. These unit operations include: drying, centrifuging, filtering and sedimentation. While the first three are important, they do not tend to be as complex as sedimentation, and thus will not be as exhaustively treated. Sedimentation is very widely applied, not

Jan 1, 1986