Search Documents

By G. V. R. Landman

In order to obtain a better understanding of the explosion risk at the coal face, anomalies in the ignition sensitivity for different modes of ignition of hybrid mixtures of dust, methane and air were studied. Results indicated that the explosible behaviour of the working environment is highly dependent upon the ignition source and the fuel composition. For example, depending on the ignition source, the same hybrid mixture can be inert or extremely explosible. In conclusion, it is stressed how the explosion risk can be expressed in terms of a safety factor which takes into account the influence of both the fuel and the ignition source.

Jan 1, 1994

By Ivan V. Klumpar

If components of a gas-liquid stream react with each other and with stationary solids, involving parallel and sequential, reversible and irreversible, and slow and instantaneous reactions, the process can be defined by a set of simultaneous differential rate equations and simulated as multistage semibatch re¬actors. Each stage is divided into finite time increments. Within each increment, even the simultaneous reactions are treated as sequential. The proposed method follows process evolution from non-steady state startup to normal operating conditions. It allows computing byproduct buildup in recycles, tracer response curves and, in case of underground processes, expansion to adjacent parts of the deposit.

Jan 1, 1979

By R. H. Snow

Although industrial size reduction methods have an energy efficiency of only about 1 percent, methods of size reduction have not changed much for many years. One reason for slow progress has been the oversimple viewpoint that a single law should exist to relate size reduction to energy input. Modern simulation methods decompose the grinding process into a grinding rate function (selection function) and a breakage function. The breakage function is difficult to measure, and it usually requires tracers if it is determined from milling experiments. Prediction of breakage functions from basic principles is one objective of this paper. In this study we focus attention not on the gross energy input to the experiment, but on the spatial distribution of stress energy within the particle. We are led to this viewpoint by experimental observations of a few previous investigators (Bergstrom2, Rumpf3, Axelson4) and our own observations. Oka and Hiramatsu recently used their calculations of stress within particles for prediction of breakage, but again they tried to correlate the size of the fragments with the total stress energy, rather than the approach we propose. We assume that the stress energy is stored in the interior of the particle as the load is increased, until the particle breaks. We assume that each element of the particle breaks into fragments of a mean size that depends on the locally-stored stress energy. The size distribution of fragments is the computed from maps of the stress-

Jan 1, 1972

By William F. Lawrence

Research performed by the West Virginia University Coal Research Bureau under the sponsorship of the U. S. Bureau of Mines has demonstrated that coal-ash can be converted into mineral wool insulation of a quality equal to commercial grade mineral wool. An unexpected benefit has been gained due to the discovery that the usual and costly fluxing agents employed when using conventional raw materials are not required when producing mineral wool from coal-ash. Because coal-ash sources are commonly located close to mineral wool marketing areas and because mineral wool is seldom shipped far as a result of its low weight and high volume, the use of coal-ash may offer the mineral wool producing industry profitable opportunities. Moreover, coal-ash produced from experimental limestone based air pollution control processes also yields high quality mineral wool which may aid in retarding corrosion of metals contacted by the wool. In addition, internal fluxing effects and possible sulfur oxide utilization could provide economic advantages to the use of these "modified" ashes.

Jan 1, 1969

By R. A. Winters

At the operations level, productivity is a principle key to profitability. If you are competing with other mines that are paying roughly the same wage rate and the same prices for capital, materials, and energy, the only way your profit can be greater is by producing more output per unit of input. Mines with higher productivity have higher profit margins. Higher profit margins lead to greater operating cash flow, and cash flow is what distinguishes a dog from a cash cow. The turnaround in U.S. metals during the 1980s was in large part due to incredible improvements in productivity. According to statistics compiled by Kaufmann, 1991, labor productivity, measured as tonnes of primary production/manhour, increased 64% in steel, 94% in copper, 75% in lead, 143% in zinc, 132% in molybdenum, and 75% in gold. These improvements were hard won. However, with most modernization programs now complete, measuring and monitoring productivity becomes even more important as producers strive to maintain the gains they have achieved.

Jan 1, 1993

By Leo Gentile, David Selhorst

The $528 million Toledo Waterways Initiative (TWI) was implemented by the City of Toledo in 2002 and completed in August 2020. Toledo is one of many US cities required to implement a Long-Term Control Plan (LTCP) but one of few to have completed its plan. TWI consists of three storage and conveyance tunnels, four below grade storage basins ranging from 4 to 36 million gallons (MG), miles of sewer separation and interceptor improvements, green infrastructure and other appurtenant structures to dramatically reduce combined sewer overflows to the Maumee River, Ottawa River and Swan Creek. All three rivers flow into Lake Erie. The City’s 180-year history as a Midwest shipping, manufacturing and transportation hub provided design engineers and contractors no shortage of unknown underground challenges to complete the projects. The City will begin its 5-year Post-Construction Compliance Monitoring in 2021 to satisfy the final LTCP requirement. A program overview and experience from tunnel and underground basin construction in urban areas with buried active and legacy infrastructure will be discussed.

Jun 13, 2021

By R. L. Garrett

The quality of mineral additives used 1n a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally used minerals are bentonite, barite, barite/hematite blends and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity, gel strength and to provide a low permeability filter cake. A multi-million dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason why oil companies who use these materials sometimes set their own quality standards beyond those already specified in API Spec. 13A. Also discussed in this paper are the current standardization activities in API Committee 13 on these minerals.

Jan 1, 1986

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining the health and safety of miners. This paper evaluates potential real-time monitoring solutions for detecting and reducing diesel particulate matter (DPM), mine fires and dust in situ and examines the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limits. In this study, relevant documents, including research papers, trade publications and manufacturer website information, are reviewed to identify research gaps. This paper also includes evaluations of contemporary sensors (airflow, gas, dust and silica), control system and software technologies, data transport systems, the Industrial Internet of Things (IIoT), ventilation network simulators and control devices to identify potential health and safety research gaps. Examples of some mines in Canada, Australia and the United States that have been using ventilation monitoring and controls are included as well. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

By Jamal Rostami, Tom Iseley, Saleh Behbahani

Tunnels and underground infrastructures assets, like all assets, deteriorate with time. At some point, they reach the end of their useful life. Therefore, frequent inspections, higher levels of maintenance, and rehabilitation are needed to address loss of life and safety concerns. The repair cost of tunnels will increase if maintenance of tunnels is not satisfactory and timely. Historically, tunnel inspections have primarily relied on visual and manual procedures. Due to their time-consuming nature and susceptibility to human error, there is a demand for alternative automated techniques that can enhance efficiency and reliability in tunnel inspection. By utilizing a tunnel scanning system, such as laser scanner and thermography, or photogrammetry system, tunnel inspection cost, time, and personnel can be reduced. The goal of this study is to utilize deep convolutional neural networks (CNNs) for automated identification of defects in tunnel lining inspection. This paper presents a framework to classify two types of defects in tunnel lining (water leakages and cracks) using CNNs. The CNNs were trained and tested using 4,608 images. The Precision, Recall, and F1 Score were each 99.6%, confirming the viability of this approach in the automated defect identification in tunnel lining.

Jun 23, 2024

By Peter Amelunxen, Brandon Akerstrom

Since its introduction 40 years ago, the compartmental model of flotation has been used to predict the performance of mechanical flotation cells. However, it has found limited success for modeling dual-chamber machines and, as a result, engineers have adopted empirical correction factors usually derived from field audits of industrial cells to predict the performance of dual-chamber flotation cells. This paper introduces an extension of the compartmental model that applies to both single- and dual-chamber cells. The model is tested against pilot test work performed at Capstone’s Pinto Valley concentrator, and then used to evaluate the key operating and design parameters of dual chamber flotation cells. The results suggest that the design of the mixing chamber — for example, whether it is pneumatic or mechanically agitated — is not a significant contributor to overall machine performance. The work also suggests that the highest recoveries are achieved when the froth recovery is high, and longer separation chamber residence times and/or higher internal circulating loads are only beneficial when the froth recovery is low. Lastly, the results show that the single most important driver of the machine performance is the froth recovery of the separation chamber.

Mar 1, 2025

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By D. A. Bird

Geochemical models using published thermo-dynamic data and laboratory derived kinetic rate laws allow prediction of post-closure pit lake geochemistry at open pit mining sites. A combination of "forward" and "inverse" modeling techniques can predict the pit lake geochemical evolution from initial infilling to eventual steady state attained decades or centuries after closure. Computer codes have been developed to model chemical reactions such as pyrite dissolution, describe the ground-water flow regime, and provide rock-water ratios. The incorporation of site specific information, such as ultimate pit dimensions, geologic and hydrologic data, acid generating potential (AGP) vs. acid neutralizing potential (ANP), and laboratory derived kinetic rates, allows application of the model to open pit mines at any stage of development.

Jan 1, 1994

By JURGEN KRETSCHMANN

The European climate and energy framework for 2030 is highlighting the reduction of man-made CO2 by increasing the use of renewable energy. In this spirit, Germany has decided to erase coal use as an energy source by 2038 completely. This strategy premises a feasible, responsible and sustainable post-mining management. The Research Institute for Post-Mining (FZN) at the TH Georg Agricola University in Bochum, Germany, has developed a holistic approach to meet post-mining challenges. In all efforts, the FZN aims to achieve the fundamental goals of the United Nations to deal with the resources of our planet responsibly and sustainably.

By William C. Larson

The Bureau of Mines, as a result of its contract research program, is developing a retractable core bit for the wireline drilling system (Retractable Sit System, No, H0272004). The prime contractor, Longyear Company, Minneapolis, Minnesota, and the subcontractor, Doerfer Division, Cedar Falls, Iowa, have designed, fabricated, and are currently field testing the in-hole retractable bit system. he objective of the program is to develop a minerals exploration core drilling system that allows retraction of a worn out bit and insertion of a new core bit, without pulling the drill rods out of the hole. To date, the results of the project are encouraging, and the retractable bit contract is currently in the last phase of a four-phase program, which is on schedule and under budget.

Jan 1, 1980

By W. C. Bagby

The Dee disseminated gold deposit is the northernmost mine in the Carlin gold belt. We analyzed soil samples £ran undisturbed areas overlying the deposit to determine the usefulness of soil geochemistry in identifying ore zones. The depth of sampling ranged from 12 to 14 inches, depending on soil development. The -80 mesh fraction was analyzed by atomic absorption for Au, As, Sb, Hg, and T1 and by semiquantitative spectrographic analysis for Ag. Highly anomalous Au, Kg, As, Ag, and Sb are most closely associated with ore zones whereas T1 is more broadly dispersed. Hg is the only element that identifies deep ore.

Jan 1, 1984

By Fred L. Myers

The use of finite element programs for evaluating large grinding mill shells is becoming increasingly popular. However, large scale, detailed analysis can become a burdensome task when one is required to manually prepare the necessary data to be entered into the program, while evaluating the voluminous results is even more devastating. Although available computerized finite element analyses can reduce computation time from years to months or even weeks, additional pre and post processors can reduce the time for data preparation and result evaluation to hours, while simultaneously reducing the probability of human error. Examples of the uses of these processors are presented as well as typical modeling techniques.

Jan 1, 1979

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The rare earth element (REE) industry has sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive concentrations. These deposits are extremely uncommon, particularly in the United States. Given the criticality of these materials and the need for a sustainable domestic supply, the current research seeks to leverage the generation and treatment of acid mine drainage (AMD) as an autogenous process that can lead to concentrated REE resources. 

By D. Rucker

Flow models are used to predict the extraction efficiency of metals in rock piles. These models typically use hydraulic parameters obtained through column studies, which assume that the material in the column wholly represents the entire pile and the parameters can be upscaled several orders of magnitude for model evaluation. This assumption fails for parameters that are spatially variable or scale dependent. To overcome these issues, measurements made directly on the heap at the appropriate model scale can be made with the electrical resistivity method. The method aims to map the variations in the electrical resistivity, which can be associated with moisture content, degree of fines, metal content, and leachate concentration. We present an example of calibrating the resistivity with borehole measurements of moisture using geostatistics to show how the resistivity method can be used to obtain a spatial moisture distribution. It was shown that cokriging the resistivity and moisture together gives a more reliable distribution.

Jan 1, 2010

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The overburden responses in gently inclined orebody mining are different from those in horizontal orebody affected by the orebody dip angle. In particular, the mining-induced stress presents asymmetrical distribution characteristics spatially, resulting in stress concentration and large-scale pressure relief phenomenon in the surrounding rock. As a result, frequent ground pressure disasters such as roof collapse and barrier splitting occur frequently. Moreover, the ground pressure evolution law and the interaction between stopes in multistope mining are complex. The effective ground pressure control measures cannot be taken due to unclear understanding of the evolution of stress and displacement fields, justifying the investigation of the distribution and evolution of underground pressure for safe and efficient mining.

Jun 1, 2023

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

The resurgence of severe lung disease among U.S. coal miners has not only highlighted the need for improved dust controls, but also the need for an improved understanding of dust characteristics and monitoring strategies [1]. Following up on prior work by the National Institute of Occupational Safety and Health (NIOSH) to demonstrate a novel wet dust collection system on a roof bolter [2], the current study explores the effect of that system on dust characteristics and uses interlaboratory comparisons to comment on analytical methods. Results indicate the wet system did not appreciably affect the composition or size of respirable dust in the vicinity of the operating roof bolter. However, the system does appear to have substantial benefits for the operator. NIOSH has already shown it can reduce the respirable dust mass concentration to which the operator is exposed during dustbox cleanout [2,3], which is a frequent maintenance activity that can re-aerosolize dust, and new results here indicate the silica and silicates content in this dust may also be reduced, thereby reducing the overall hazard. Moreover, regarding analytical methods, excellent correlation was demonstrated between measurements of quartz mass, taken first by NIOSH and then by a university laboratory, using direct-on-filter Fourier transform infrared (FTIR) analysis. This method is the basis for envisioned “end of shift” silica monitoring (quartz is the predominant form of crystalline silica in coal mines) [4]. For particle-level analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), there was more variability in results generated by two independent university laboratories.

Mar 1, 2024