Search Documents

By Susan G. Bilhorn

A number of studies have been conducted in active and inactive mine environments using continuous monitoring and data acquisition systems to detect various parameters. In addition to the information obtained for research purposes, these monitoring systems can provide a means to remotely collect required information (such as radon daughter concentrations and air velocity) and control various conditions (such as fan operation and air door position) in numerous working sections of an active mine. Selection of detector locations and placement, which are critical to obtain the information and control desired while not inhibiting mine operations and influencing the detector readings, are covered in this paper.

Jan 1, 1984

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

By Karl C. Dean

The current emphasis on environmental problems has focused attention on the massive nationwide accumulations of mine, mill, and smelter wastes that represent potential air and water pollution hazards. The pollution hazards can be reduced or eliminated by utilization or stabilization of these wastes. The U.S. Bureau of Mines, since the inception of the Solid Waste Disposal Act of 1965, has been conducting research to determine the practicality of various utilization and stabilization procedures. Investigations include partial extractions of desirable waste components and full utilization of the wastes as simulated soils or in ceramic or other structural products. Chemical, vegetative, and combined chemical-vegetative methods of stabilization have been actively studied. This report updates information previously developed by the Salt Lake City Metallurgy Research Center and presents the current status of antipollution solid waste work 1/,2/.

Jan 1, 1970

By R. Wisniewski

Every underground coal mine in the United States must deploy and operate a wireless communication and tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 96 hours, and the requirements in the MINER Act for the tracking systems to be ?calculated to be serviceable? and the communications systems ?redundancy?. These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using the tools that are available and commonly used by the Reliability, Maintainability, & Availability community.

Feb 23, 2014

By R. M. Rowe, T. E. Irwin

A flowsheet was developed for upgrading Climax tin concentrate to about 45 percent Sn. Bench-scale test work conducted at AMAX Extractive Research and Development, Inc., was used to design a multiple-stage tin- processing flowsheet which included screening, high-intensity magnetic separation, and high- tension (electric- static) separation. Formal engineering and plant installation was accomplished in-house by Climax mill personnel. The successful start-up operation of the facility was the joint effort of the AMAX R&D and Climax-mill staffs.

Jan 1, 1986

By Dennis C. Parker

The Porters Creek clay is mined for its absorbent properties. The formation is part of the Upper Mississippi embayment and is recognized in Alabama, Mississippi, Tennessee, Kentucky, Illinois, and southeast Missouri. Major minerals in order of abundance are Montmorillonite, Quartz, Illite, Kaolinite, and Chlorite. Mining consists of open pit operation utilizing track loaders or scraper. The clay is dried or hardened in rotary kilns and crushed to size by roll crushers. The clay granules are sized and air classified prior to storage for shipment or packaging. Granules are sold for pet absorbents, oil absorbents, anti-skid material, fertilizer, and pesticide carriers.

Jan 1, 1979

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels, as related to maintenance (service) intervals, during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type (technology) and tuning of the engine, the type of work performed as related to the engine workload, suggested maintenance intervals, the altitude, the temperature and the humidity of the atmosphere of the underground mine, the properties of the fuel, the operator's training and experience level. Necessary ventilation quantities were calculated based on exhaust gas concentration measurements, site specific relationships between pollutants and adjusted air quality indices. Diagrams comparing necessary and recommended air flow for several equipment groups featuring two engine types and for different maintenance intervals are presented.

Jan 1, 1998

By T. BoBo

"In the 1990’s metal prices were trending in a long term decline and the usual cost cutting exercises were adopted. Cuts to research and development made innovation difficult and the outlook was grim. But necessity is a strong motivator, and these conditions spurred the Mine-to-Mill movement which optimised across organisational “silos” and utilising new technology tools, innovative software and increased computing power. Many applications of Mine-to-Mill exploited the fact that comminution is usually the site processing bottleneck, and that blasting is more efficient at breaking rock than grinding. This approach sought to: • Understand and characterise rock breakage from mining to the mill • Develop models and simulators for blast design, fragmentation, crusher and mill circuits • Develop tools to measure in real time the particle size distribution of rocks on conveyors and Run of Mine (ROM) muckpiles • Ensure effective communication across the silos between geologists, blast design engineers, mining engineers and metallurgists These methods and the technology tools available in the 1990s were widely adopted at numerous sites around the world with significant benefits. SAG mill throughput increases of 10-20% were common. This was the advance the industry desperately needed. It was low capital cost; it was obvious. It was here to stay. Except, in too many cases, it didn’t. In the minerals price boom of the 2000’s Mine-to-Mill was no longer necessary to “survive”, even though it was still good business. Some operations, including some of the early success stories, slipped back to old habits of optimising within organisation silos instead of across them. Fortunately, other operators still embraced Mine-to-Mill and developed new techniques. Mine to Mill was still successful, but it not as widely adopted as we had expected it to be.Now the boom has ended and operations are again under cost pressure. Since these are the same circumstances that created Mine-to-Mill, it seems time to achieve the wider adoption. Since the 1990s many new or advanced technology tools are available for Mine-to-Mill projects: blast-hole sensors, new explosives formulations, new blasting techniques and modelling, ore tracking devices, improved image analysis to determine size, texture and colour of coarse ore, grade sensors, whole-stream simulation tools, even more powerful computing hardware and data analysis software. If we could achieve so much in the 1990’s, how much more can we achieve today when we have the same imperative, the same potential and a larger number of high technology tools?"

Jan 1, 2017

By Steve Kral

One of the world’s most successful mining shovel manufacturers believes its name is not very well known in North America, particularly in the United States. And there are plans under way to improve on that. Never mind that it is one of the largest mining shovel manufacturers in the world. Or that the mining division has 800 machines in operation worldwide, 100 of them in the United States. And the company currently holds 30% of market share worldwide and 10% in the United States. Forget about the fact that it has already sold more machines world-wide this year than it did during 1995. None of that is good enough. O&K Mining GmbH Dortmund is the mining division of Germany’s giant O&K Orenstein and Koppel. It is one of three divisions of O&K Orenstein and Koppel AG, a US$1.2-billion company. The other two divisions are construction equipment and escalators. The mining division, though, is one of the company’s most successful.

Jan 1, 1996

By C. O. Brawner

A recent advance in slope dewatering-depressurization and stabilization is the use of vacuum assist horizontal drainage. (Brawner and Pakalnis) Horizontal drains have been used for several decades to reduce water pressures in slopes to improve stability. The benefit from vacuum assist arises from an increased hydraulic gradient caused by an induced negative atmospheric pressure. A research program included a laboratory model whereby the effects of vacuum drainage were evaluated. Three case studies are described where the technique has been successful. The first is in a rock slope where flows increased from 0.1 1/min. under gravity drainage up to 1.2 1/min, upon vacuum. The second study involves installation of 17 drains placed at a slightly downward gradient to intercept and de- pressurize aquifers under a major tar sand deposit in Canada. The third study was on a large open pit copper mine in British Columbia where flow increased about 30 per cent.

Jan 1, 1984

By D. Bhattacharyya

The adsorption and desorption of gold cyanide by activated carbon is significantly influenced by particle size of the activated carbon particles and the chemical environment. A series of adsorption and elution experiments have been performed with ten different particle size fractions. The tests indicate that although the ultimate adsorption capacity is independent of the activated carbon particle size, the adsorption rate is strongly affected by the particle size. Further, desorption characteristics using traditional Mintek and atmospheric Zadra procedures reveal interesting trends with variation in particle size and will be discussed in this paper.

Feb 23, 2014

By A. Almeida, D. Castro, K. Ingmarsson, D. Ferreira, R. Tamir

Mine-to-mill improvements can be initiated at any stage, but it is our assertion that drilling accuracy is a practical anchor in any operating mine or quarry for a structured continuous improvement process. This paper will: 1. Define deviations from plan and provide some best practices for maintaining drilling accuracy. 2. Introduce tools and methods to monitor and calculate consequences of accurate versus inaccurate drilling. 3. Demonstrate the use of these tools and methods and their impact on one cost item, the mitigation of oversized material by a hydraulic hammer. 4. Provide recommendations for implementing improvements.

Feb 1, 2023

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and con¬crete is described Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fastopening valve discharges the com¬pressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh-pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited

Jan 1, 1997

By Quansheng Li

Large-scale coal mining will cause environmental problems such as aquifer damage, land excavation and occupation, soil erosion, vegetation damage, and regional landscape damage. The existing coal mine environmental restoration technology is relatively simple, and there is a lack of systematic research on environmental total factors. Based on the mechanism of coal mining damage and the laws of environmental natural succession, the concept of “coal environmental protection mining” is proposed, which combines damage reduction mining and environmental element system restoration. In accordance with the environmental protection principle of “source protection, process damage reduction, and systematic restoration,” a technical system of “coal environmental protection mining” is constructed for the two types of mining damage scenarios: underground mining and open-pit mining. In view of the damage characteristics of underground mining, source environmental protection technology based on optimization of mining process parameters, stability maintenance and damage reduction technology for overlying rock bearing arch shell structure, zoning and time-sharing treatment of surface cracks, and direct drainage irrigation technology for mine water have developed. In accordance with the damage characteristics caused by open-pit mining, land-saving and source reduction damage technology, near-natural stratigraphic reconstruction, topsoil improvement, and environmental storage and utilization technologies for seasonal precipitation have developed. By applying the technology in this paper, the maximum surface settlement value of 12401 working face in Shangwan coal mine was relatively reduced by 25%, the surface cracks have been adjusted from step-type cracks to dynamic small cracks, and since the technical implementation of the Shendong mining area in 2010, the vegetation coverage has increased loss and crushing decreased by 0.06 km2 every year, the environmental restoration period of the dump site was advanced by more than one year, and the vegetation coverage rate increased by 41.78% compared with the background value in the semi-arid area of the victory open-pit coal mine demonstration area. A surface reservoir with a water storage capacity of 400,000 cubic meters has been built, and the seasonal and graded utilization of mine water has been realized. An underground reservoir with a water storage capacity of 1.22 million square meters has been built in the Baorixiler open-pit coal mine.

Jun 25, 2024

By Donald M. Podobnik

The Cuajone Concentrator of the Southern Peru Copper Corporation is located approximately 900 kilometers southeast of Lima, Peru, near the 500 year old town of Moquegua, in an area that has been occupied since antiquity. Since the plant was started in July, 1976, the throughput has steadily increased from 36,000 to 46,000 metric tons per day. The widely distributed molybdenite content of the ore body ranges from 0.02 to 0.04% MoS2. The molybdenite content of the copper concentrate has always been sufficient to justify operation of a byproduct molybdenite plant. During the first nine months of 1980, the average grade of the ore was 1.169% copper and 0.026% molybdenite.

Jan 1, 1981

By R. C. Bunge

A magnetogravimetric separation is the consequence of two competing forces with opposing directions, i.e., magnetic buoyancy and gravitation (or centrifugal force). While magnetic buoyancy is a function of particle volume, gravitational force depends on particle mass, thus permitting a separation according to specific gravity. Since magnetic buoyancy is not a phenomenon of common knowledge, this chapter is meant to briefly introduce the theory of magnetogravimetric separations. A particle that is suspended in a magnetic fluid which is exposed to an inhomogeneous magnetic field experiences a repulsive force -the so called magnetic buoyancy. In order to illustrate this effect, an analogy with the more familiar hydrostatic buoyancy is drawn. Hydrostatic buoyancy occurs due to unsymmetrical pressure distribution 'above' and 'below' a suspended particle (fig. 1).

Jan 1, 1990

By G. B. Amicucci

A Denver Autometrics Particle Size Monitor, PSM-400, was installed at Golden Sunlight Mines, Inc. in October 1988. The PSM-400 measures the grind product's particle size and percent solids. The particle size is used to control grind size by automatically adjusting mill feed rate. The PSM's continuous response to ore changes has improved grind product uniformity and mill throughput. Metallurgical testing has shown the PSM's accuracy to be +/-1 % + 150 µm (100 mesh).

Jan 1, 1991

By Robert Moore Lewis

A unit for separating minerals into two prescribed size fractions, designated as a Lewis Hydrosizer, was developed at the North Carolina State University Minerals Research Laboratory. Ore samples with different mineral compositions, including coal, were separated effectively with the laboratory continuous unit. Commercial size units are in operation in North Carolina and Mexico, and under construction in Norway. Additional units are being build or are in the planning stage at several companies.

Jan 1, 1983

By Robin P. Gardner

The mechanistic approach to comminution consisting of incorporating particulate breakage functions into a suitable population balance equation has been developed by a number of researchers over the past decade or so. (1) To date this approach has been developed and demonstrated primarily for batch-operated, laboratory or small-scale ball mills. However, since industrial mills are mostly quite large and operated in the continuous mode; suitable population balance models and methods for obtaining the necessary breakage and other model parameters must be developed. This paper describes and investigates a radioisotope tracer technique for this purpose, Population balance models previously developed(2,3) are adapted for this study.

Jan 1, 1974

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014