Search Documents

By A. K. Bakshi

Slurry rheology affects autogenous grinding performance by changing the rock's breakage characteristics. In this study pilot scale batch autogenous grinding was carried out to observe the effect of viscosity on the breakage characteristics of the rocks (the media), and on the overall specific energy consumption. Clay/fines content, and temperature of the initial charge, were varied to alter the viscosity of the slurry. Results showed that at higher slurry viscosity, rocks became more difficult to break, resulting in an overall increase in the specific energy consumption of the mill. Also, it was observed that viscosity had a significant effect on the amount of critical size material present in the grinding circuit, where the critical size material is the material which is too large to be effectively ground in the mill, and too fine to act as grinding media.

Jan 1, 1996

By J. M. Bray, R. R. H. Cohen, P. Kiousis, S. R. Al-Abed

"INTRODUCTION Conventional tailing storage and management practices typically utilize engineered facilities, such as ring dikes and valley impoundments. To reduce the environmental costs associated with disposing of mine wastes in tailing storage facilities (TSFs), several beneficial re-use strategies have been developed over the years. For example, thickened tailings have been used for paste backfill. It is common for tails to comprise up to 60% of the material’s total weight and it has been estimated that TSF volumes can be reduced by 60% when using this strategy, (Benzaazoua, et al. 2004). Other beneficial re-use strategies have produced unpaved temporary access roads, hot and cold asphalt, chip seals, self-compacting concrete, and golf course sand traps. This project sampled mine tailings from two different TSFs in Colorado and produced structural concrete that could potentially be used for commercial foundations, sidewalks, and paved roads. The tailings were substituted for the fine aggregates typically found in conventional concrete. The two main objectives of this study were to investigate the structural integrity of the produced concrete samples and the leaching of heavy metals from the resulting concrete. The ratio of tailings to fine aggregate (T/FA) was carefully studied to find if there was a correlation between the substitution rate and the structural integrity. The potential maximum substitution rate was also investigated for the produced concrete specimens. The potential of leaching mining impacted water (MIW) was evaluated by comparing the leachability of the raw mine tailings to the encapsulated tailings by using standard shake extraction prediction tests. MATERIAL AND METHODS Materials The four components that make up the concrete mix design for this project are: cement, coarse aggregate (gravel), fine aggregate (sand and mine tailings), and water. The type I/II ordinary Portland cement (OPC), gravel, and sand came from local cement and concrete companies in Denver, Colorado. Mine tailings were collected from two different TSFs in the Rocky Mountain Region, where Pride of the West TSF in Silverton, CO will be denoted as Site A. The primary metals of interest at the mill site are gold, silver, lead, copper, and zinc. The location of Site B will not be mentioned in this report due to confidentiality agreements with the mining company"

Jan 1, 2016

By M. E. Kuchta

LKAB's Kiruna mine, located above the Arctic Circle in northern Sweden, is one of the world's largest underground mines, and it is one of the most modern. The Kiruna orebody is a high-grade magnetite containing about 80% low-phosphorous iron ore and about 20% high-phosphorous iron ore in situ. The mining method used is large-scale sublevel caving. Due to the blending of high-phosphorous ore with low-phosphorous ore during the extraction process, only about 20% of the run-of-mine ore can be used for the mine's low-phosphorous product. The blending process is highly irregular and difficult for the mine-planning personnel to predict. An algorithm was developed that uses principles of gravity flow to predict the run-of-mine phosphorous grades from the in situ geologic block model. The model can be used for both long- and short-term predictions.

Jan 1, 2003

By P. Tsang

To gain insight into the current status of pillar design practice in the underground coal mines of United States, a survey has been undertaken in the late 1993 and early 1994. A total of 552 room-and-pillar mines and 75 longwall mines have been surveyed to collect general, geological and mine plan information. The collected information are critically analyzed with special emphasis on the pillar design criteria adopted in these mines. A safety factor analysis has also been carried out for the pillars in room-and -pillar mines.

Jan 1, 1995

By R. M. LaDouceur, C. A. Young, W. Nicholas

"Salicyl hydroxamic acid (SHA) adsorption on two rare earth oxides, lanthanum and yttrium, was studied. Adsorption at both surfaces occurred in two stages. Initially, the monovalent anionic collector appears to adsorb significantly and instantaneously in stage one and then becomes sluggish in stage two presumably because the initial stage passivated the surface. By comparison, adsorption during the sluggish second stage with lanthanum oxide did not stop but with yttrium oxide essentially stopped. Surface monolayer formation could not be observed in either of the two cases. Both stages appear to be due to multilayer formation of a surface precipitate as proven by Raman Spectroscopy for lanthanum oxide but inferred for yttrium oxide. Unlike the use of octyl hydroxamate as stated in the literature, increasing temperatures do not increase adsorption such that flotation of rare earths with SHA may be performed at room temperature leading to improved recoveries as well as significant energy savings. INTRODUCTION Rare Earth Elements (REEs) are comprised of the 15 lanthanides along with scandium and yttrium. The REEs with lower atomic numbers are relatively more abundant and are categorized as light REEs. On the contrary, the REEs with high atomic numbers are less abundant and referred to as heavy REEs. They are not really “rare” and, in fact, some of them are quite abundant in the Earth’s crust; it’s just that they “rarely” exist in concentrated deposits but rather are found dilute and practically everywhere. REEs share very similar physico-chemical properties but, because many of these properties are unique, they have gained enormous importance in recent times making several critical and strategic pending their use. For example, REEs have found extensive application in phosphor coatings, magnetics, and automobile cracking catalysts. Early technology was not advanced enough to produce commodity level production of the REEs and can be attributed to REE-bearing ores containing many rare earth minerals (REMs), not just one. In this regard, there are numerous REMs but bastnaesite, xenotime and monazite are considered to be the most common. Bastnaesite is a fluorocarbonate whereas the other two are phosphates. The separation of the individual REE-bearing minerals from the ores is not an easy task since they also exhibit very similar properties. Consequently, when flotation is used, it is done to produce bulk REM concentrates. For REM flotation, it is well established that octyl hydroxamate is more selective than fatty acid collectors (Pradip and Fuerstenau, 1983 and 1991). Liu et al. (2006) indicated that hydroxamates are the most common collectors for REMs. Pavez et al. (1996) studied the adsorption of oleic fatty acid and octyl hydroxamate on REM surfaces. Cui et al. (2012) studied the interaction of octyl hydroxamate with various REMs surfaces using various spectroscopic techniques such as XPS, FT-IR and Raman along with electron microscopy and concluded that such techniques offer ample information to establish adsorption mechanisms. Ren et al. (1997) studied napthalenic hydroxamic acid as a unique collector for flotation of REMs from bastnaesite ore and indicated that more selective collectors were needed. From these studies, it is clear that the quest of more selective collectors is essential but understanding how they adsorb at mineral surfaces is prerequisite to improving flotation performance."

Jan 1, 2016

By William R. Nash

Case histories of water problems in underground mine shafts and tunnels are outlined to illustrate varying degrees of sophistication in grouting techniques currently applied in such construction. The interception of water underground can be one of prior knowledge, i. e., the site investigation provides necessary data to plan a grouting program prior to construction start, or excavations may encounter "changed conditions" or unplanned water. The latter includes catastrophic inflows and emergency situations where the structural integrity of a building or concrete shaft lining are jeopardized. The presentation of this paper outlines some applications of grouting work in underground mine construction throughout the United States in a variety of geological provinces and for a variety of minerals.

Jan 1, 1984

By D. M. Thayer

Dry magnetic separation of feebly magnetic minerals and wet magnetic separators suitable for highly magnetic minerals have been commercially utilized for a number of years. The beneficiation of magnetic taconite ores by conventional, low intensity magnetic separators in combination with flotation is well established technology (1). However, over the past decade much effort has been expended in developing techniques for the upgrading of feebly magnetic oxidized iron ores (2,5). Such research and development have been stimulated by the limitations of the above-mentioned techniques in application to ores containing fine material; for example, ores requiring fine grinding for liberation or slime-forming ores such as the oxidized taconites or semi-taconites. Wet separation has allowed the reduction of the minim particle size that can be effectively treated from that allowable for high intensity dry magnetic separation. Consequently, the development of high intensity wet magnetic separation methods has received much attention in the search for an effective method to treat the weakly magnetic minerals. Recently Lawver and Hopstock (5) have provided an excellent review of the state of know- ledge of this technology. In addition, a valuable compendium of available laboratory and commercial devices is included. Nonetheless, the feasibility of the use of high intensity magnetic separation in a particular application is largly empirical in nature and requires experimentation to chazacterize the response of a particular ore. The purpose of this paper is to assess the incorporation of high intensity magnetic separation for the beneficiation of a non- sliming specular Michigan hematite. Particular attention is focused on the existence of a lower limit of particle size that can be treated effectively and is inherent in the use of these techniques. Additionally, a rationalization of various models presented in the literature is attempted.

Jan 1, 1979

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998

By Samuel S. M. Chan

Rock surrounding mine openings frequently is an impermeable type such as shale or granite. Most rock, however, has joints, bedding planes, cleavage planes, or other potential discontinuities. Permeability to fluids (gas or liquid) may exist via natural joints or fractures in an otherwise impermeable rock. In the mining situation, tectonic and induced tensile and shear stresses may be great enough to cause joints to open or fractures to develop in previously solid rock. The rock, as a result, becomes less self-supporting and may - require artificial support such as rock bolts or timber. Simultaneously, as fractures develop, permeable paths may be created. If fluid can be injected into a previously solid and impermeable rock mass, a logical conclusion is that a fracture (crack) flow path must be transmitting that fluid. The U.S. Bureau of Mines Laramie (Wyo) Energy Research Center has been evaluating results of in-situ oil shale fracturing (hydraulic or explosive) and retorting experiments by. a fluid (air) injection , and borehole air flow profile logging technique since 1956 (1, 14, 15). In the oil shale case, it is imperative to know the location and flow capacity (permeability) of natural fractures, if they exist, and induced fractures that inter-connect vertical wellbores at depths of fifty to several hundred feet. By injecting air into one wellbore in a system of several wells and measuring input volume and pressure while simultaneously measuring the output of other wellbores, the minimum areal extent of interconnecting permeable fractures can be determined. Exact locations (depths) of fractures and individual fracture flow capacities between wellbores can be determined by air flow profile logging (14, 15). Knowledge of fracture locations and permeability is essential to rational experimental in-situ retorting design.

Jan 1, 1973

By R. T. Torrie, J. R. Mernagh, D. B. Chambers

l, INTRODUCTION Uranium mine and mill workers are exposed to external gamma and beta radiation fields from radioactive ore. In the past the average uranium content of ores mined in the United States and Canada ranged from about 0.1% to 1.0% U308 with pockets of much higher grade ore. Holiday (1973) reported that radiation surveys in the U.S. uranium mines found mean gamma "radiation rates ranged from 0.20 to 0.70 mrem/h. Such radiation rates cause relatively insignificant exposures." Others also concluded that the external gamma radiation fields associated with uranium mining did not result in significant worker exposures (Federal Radiation Council, 1967; Simpson, S.D. [et al], 1959) Gamma exposure levels in most modern-day Canadian uranium mines are reported to be low with average annual exposures estimated to be less than 1 rem/a (Frost, S.E. [et al], 1981). However, two developments are taking place which affect the potential significance of external radiation fields in the uranium mining environment. The first development stems from the most recent system of dose limitation developed by the ICRP which is intended to limit the workers' overall risk from exposure to ionizing radiation through the adoption of a sum rule (ICRP 26, 1977) which combines external and internal radiation exposures. In the case of exposure to radon daughters the sum rule will have the effect of reducing the annual exposure limit below the recommended limit by an amount that depends on external radiation and other sources of internal exposure such as the inhalation of ore dust (ICRP 1980). The Atomic Energy Control Board of Canada (AECB) is reviewing this subject and is expected to produce its recommendations shortly. Irrespective of the form of the sum rule eventually adopted by the AECB, it is clear that the net effect of the sum rule will be a collective reduction of the individual dose limits for individual exposure pathways. The second factor is the increasing development of high grade uranium deposits in Northern Saskatchewan. Some of these ore bodies have an average ore grade of 1% to 5% U308 or greater. Since the potential external radiation fields increase in proportion to the ore grade, it is apparent that increased effort in radiation protection planning is required in order to develop safe yet workable methods for mining and milling such ores. This paper is intended to provide information which can be of assistance in the formulation and development of a mining and milling plan. The principal focus of the paper is source identification and the design of radiation protection measures to limit external gamma radiation exposure. The exposure of workers to external beta radiation fields is also discussed. The paper is organized as follows: - Section 2 deals with source characterization. - Section 3 discusses the effects of finite source size and distance (i.e. geometry effects). - Section 4 presents selected data that are useful in evaluating shielding requirements. - Section 5 discusses the potential beta radiation fields. - Section 6 discusses practical data requirements for worker exposure scenarios. - Section 7 presents a variety of work exposure calculations. - Section 8 is a summary of this paper. 2. SOURCE CHARACTERIZATION This section develops the basic formulae for estimating the fluxes and doses from external gamma radiation. The calculation of the radiation flux due to a distributed source (i.e. a linear, area or volume source) as a function of distance assumes that any distributed source can be treated as a summation of point sources. [ ] Uranium ore contains radionuclides from both the decay chains of U-238 and U-235. In this paper the radioactive daughters are assumed to be in secular equilibrium with the uranium parent. (If natural thorium were present in the ore in significant quantities, the gamma rays originating from Th-232 would have to be added to the gamma rays from the uranium series). In all, there are over 50 separate gamma rays (as well as alpha and beta particles) emitted from the U-238 and U-235 radioactive decay series (USHEW 1970). The total

Jan 1, 1981

By M. S. Prasad

In earlier work it has been shown that paper filler clay products can be obtained from primary kaolin deposits of Minnesota. The objective of the current work was to reduce silica and iron contaminants and to maximize kaolin recovery to higher value products suitable for paper coating. This results in achieving a finer and cleaner product conforming to paper coating specifications. Cationic flotation and high gradient magnetic separation were used to remove free silica and iron, respectively, while attrition grinding and ultrasonics have been examined for particle size reduction. The results of this work are presented and discussed particularly with respect to application-oriented product properties. Budgetary estimates are presented for a 200,000 ton/year processing plant based on the process flowsheet developed and optimized by the study.

Jan 1, 1991

By Frank A. Jerabek

Pneumatic stowing was first introduced in longwall mining in the middle twenties. Since that time it has advanced through many stages of development, particularly abroad, which have greatly improved its efficiency and contributed to its growing use. Pneumatic stowing originated in coal mining but has also been adopted in metal mining. This paper discusses the techniques of pneumatic conveying of. stowing material and equipment and applications of pneumatic stowing.

Jan 1, 1966

By Goran Mathisson

In several investigations the correlation has been studied between the fuel consumption and the reducibility of the charged material in the zone of indirect reduction in the blast furnace (1, 2, 3, 4, 5). It has been found that increased reducibility allows greater gas utilization which accordingly lowers the fuel consumption. In direct reduction units this relation has not yet been fully established partly owing to the lack of accurate test methods and experience with different materials as regards reducibility. However, since the production rate in a direct reduction unit is closely related to the time required to reach high degrees of reduction, the reducibility must be regarded as one of the most important properties of the material.

Jan 1, 1979

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By R. Hogg

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size end density.

Jan 1, 1986

By A. Röttger, W. Theisen, J. Küpferle, M. Alber

"Wear of TBM tools significantly affects tunneling advance rates. Wear-prediction models are based (amongst others) on the abrasivity of the present geology, which is determined via laboratory tests. To evaluate the results from such tests in context, this work considers the tribological system TBM tool from a materials technology perspective. In so doing, the microstructures of different application-oriented materials are presented and discussed in terms of their wear behavior and wear resistance. The significant influence of tool materials on the abrasivity of the geology and thus wear prediction models has already be identified. LCPC, Cerchar and nano-scratch experiments have been performed as confirmation. Material-dependent wear mechanisms and their correlation in terms of tunneling have shown that it is mandatory to consider the complete tribological system to estimate the wear of TBM tools. 1 INTRODUCTION Mechanized tunneling is vital to ensure necessary infrastructure development in megacities like Tokyo (Bay Tunnel), Istanbul (Eurasia Tunnel) and Mexico City (Tunnel Emisor Oriente). The use of Tunnel Boring Machines (TBMs) has been established for many years. In contrast to other methods such as boring and blasting or excavation using dredgers, tunneling with TBMs allows simultaneous excavation and removal of both the mineral and tunnel lining by tubbing segments or shotcrete. This makes tunneling more efficient, allowing for faster development of the tunnel in both hard rock and soil [1]. When budgeting such tunneling projects, precise planning and coordination in terms of tunneling technique choice (e.g. EPB or Slurry-shield), the relevant geology, and the associated penetration rates and tool wear are required. In particular, wear to TBM tools has a significant impact on tunneling progress. Due to wear, tools become dulled or lose their functionality because of brittle material behavior, thus reducing penetration rates and therefore tunneling efficiency [1]. As a result, additional tool changes are necessary, leading to higher overall costs due to down times and maintenance costs. Therefore, there is strong interest in a reliable and precise wear prediction model for TBMs. As already mentioned, the geology and associated wear of the tunneling tools define the maintenance times."

Jan 1, 2016

By Christopher Newman, Robert Dupuy, David Newman

"The development of a multiple level underground mine is a complex task in which geology, engineering, ground control, and unit operations are integrated into a single mine design. The components are inter-dependent and must function cohesively to ensure a profitable underground mining operation. To optimize reserve recovery, mine planning should begin from the lowest level and progress up. This limits any misjudgments or oversights of a given level affecting the underlying levels and ensures the ability to maximize recovery from each level.Mine planning should start with the exploration and characterization of the geologic setting. Once the reserve geology and quality is well understood, then mine planning can begin with respect to the following:,Orientation of mine works with respect to horizontal stress,,Access to the reserve,,Determination of opening widths,,Selection of back, floor horizons and pillar centers,,Selection of development and secondary mining heights,,Appropriate interburden thicknesses, and,Examine the stability of the multiple level mine through numer¬ical modeling.The multiple level mine design process and decisions are presented through a case history example. The theme is that there is one opportunity to “get it right” as well as many chances to overlook a small aspect within the design that will plague the mine throughout all levels and through the entirety of its operating life.INTRODUCTIONAs surface quarries reach their economic stripping limit and encroach on mineral and/or reserve boundaries, they approach the end of surface mineable reserves. Furthermore, modern urban sprawl has placed previously remote surface quarries within suburban development and neighborhoods, leading to significant increases in noise, dust, and vibration grievances by the community and regulators (Newman, 2017). Many mining operations have begun year-round production of underground reserves to meet growing market demands. This does not permit the typical sequence of stripping overburden in the winter to provide limestone to mine during the construction season. Underground stone mining operations in the United States commonly utilize a room-and-pillar mine layout with drill-and-blast production methodology for the development of the reserve. Within the Midwest and Eastern regions, thick and flat-lying limestone formations lend themselves to the utilization of multiple level mining layouts. While a multiple level mine plan will increase the overall recovery of the reserve, greater overburden depths, multiple level geometry, and the presence of discontinuities all require an emphasis on ground control for the planning and development of a safe and productive multiple level underground stone operation."

Jan 1, 2019

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By N. Sahin, M. Can, Z. Ekmekçi, Y. Öztürk, Ö. Biçak, I. B. Çelik, B. Kocabiyik

"In this paper, a case study from Çayeli Bakir Isletmeleri A.S. (Rize, Turkey) about the selective flotation of copper minerals from sphalerite is discussed. Çayeli Cu-Zn Sulfide Ore contains different ore types, such as yellow ore, clastic ore, bornite-clastic ore, bornite-yellow ore, and black ore. For some of these ore types, selective flotation of copper and zinc is very difficult presumably due to presence of secondary copper minerals such as bornite, chalcocite and covellite, and also surface oxidation. These factors affect Cu-Zn selectivity due to activation of sphalerite particles in the ore during the process. The main objective of this work was to improve Cu-Zn selectivity by optimization of the pulp chemistry for different ore types of Çayeli ore. After preliminary flotation tests investigating effects of different chemical conditions, a plant survey was performed to determine the plant performance and sources of the problems when problematic bornite-clastic ore is treated in the plant. Various chemical conditions are tested in the laboratory scale test for better depression of sphalerite in copper flotation circuit. Combination of Na2S+ZnSO4+MBS was found to be the most effective depressant scheme. INTRODUCTION Ore variability is one of the most important factors affecting performance of a process plant both in short and long term planning. The geometallurgical modelling becomes a common tool to determine ore variability problems and develop the most efficient solution during life of mine (1, 2). Flowsheet design and equipment selection and sizing are usually done based on the results of ore variability test works. However, in some cases ore variability may not be foreseen during the design stage and therefore the solutions should be developed based on the existing flowsheet and equipment in the plant. In this situation, ore characterisation, problem statement and diagnostic testing should be applied step by step. The problem could be due to changing feed grade, mineralogical characteristics, grindability and surface characteristics when flotation is involved. The variability in feed grade with fixed mineralogy can be handled with relatively simple modifications (i.e. adjusting throughput or equipment capacity) in the plant. Variability in ore mineralogy is the most complex and difficult problem to tackle. Because, mineralogical variations could bring variations in mineral composition, texture and liberation. These variations can potentially lead to the variations in grindability of the ore and flotation behaviour. Variations in grindability are usually managed by optimization of operational parameters in grinding circuit, as it would be costly to replace the existing equipment in the circuit (3). The variations in flotation behaviour are mainly due to variations in mineral types and distribution, texture and surface oxidation. One or all of these factors could be observed in a flotation operation. Therefore, a comprehensive investigation both in plant and lab scale should be conducted for definition of source of the problem. The testwork to solve the problem and retrieve the performance is planned and conducted depending on the source of the problem (4, 5)."

Jan 1, 2017

A comparison of gold, platinum and sulfide ion selective electrodes was made in this investigation for determination of Eh in solutions containing sulfide ions as a model system. The comparison was made in terms of the accuracy of the measured response, response time, pH dependence, and reproducibility of measurement. In addition, the sensitivity of each electrode towards changes in sulfide ion concentration was measured in terms of the change in measured Eh per decade change in concentration of sulfide ions. On the basis of a detailed investigation of the electrode processes occurring at the surface of gold and platinum electrodes, it was postulated that within the pH range investigated these electrodes respond to changes in the hydrosulfide ion, HS-, concentration in solution. In comparison, the sulfide ion selective electrode is known to respond to changes in the sulfide ion, S-, activity in solution. Although the potentials measured with gold and platinum electrodes were mixed potentials, pretreatment procedures can be used to obtain a signal suitable for process control. For control of sulfide ions in flotation pulps, the use of a gold electrode pretreated at 1.0 V with respect to a standard hydrogen electrode is recommended.

Jan 1, 1990