Search Documents

By T. J. Smolik

The Golden Sunlight Mine started full-scale operations in February 1983, with a conventional open-pit mine supplying 4464 tonnes (5000 tons) per day of milling ore. After crushing and grinding, the ore is leached with cyanide solution in large agitation tanks. Soluble gold values are removed from the sand portion of the leached ore with five stages of countercurrent washing cyclones. After thickening of the cyclone-wash overflow slurry, the gold is recovered in activated carbon with a six-stage carbon-in-pulp circuit and a five-stage upflow carbon column circuit. Pressure stripping, carbon reactivation, electro-winning and refining complete the gold recovery process.

Jan 1, 1984

By Andrzej Walentek

This paper presents the results of numerical modeling of the fractured zone around longwall gateroads. The numerical computations have been based on the results of underground measurements of the fractured zone around longwall gateroads, which were performed for various geological and mining conditions and measured with the use of the endoscopic method with a digital camera. Having results of the underground investigations, trials of duplicating them by the Finite Element Method using software PHASE and the Hoek-Brown failure criterion were performed. In order that the fractured zone predicted by the model-based computations closely simulate that measured underground, some selected parameters in the Hoek-Brown failure criterion were modified based on the earlier determined relations used for prediction of the roof-to-floor convergence in longwall gateroads. As a result, the model-based computations produce results very close to those obtained from the underground measurements. Determination of the fractured-rock zone around the mine roads is of great importance to mining practice, especially in planning and designing supports for longwall gateroads. The influence of the front abutment pressure causes the fractured rock zone around the roads to increase and results in an increase of support load. Moreover, proper determination of the fractured rock zone is one of basic elements in the process of planning roof bolting for mine workings.

Jan 1, 2009

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984

By B. D. Hong

The Coal supply and demand review arrived too late to appear in the May issue. In 1991, the US coal industry produced 902 Mt (994 million st) of coal, according to preliminary data compiled by the Energy Information Administration (EIA) (Table 1). This amount was 32 Mt (35 million st) less than the record 933.5 Mt (1 billion st) produced in 1990. Most of the decrease in coal production occurred east of the Mississippi River. The substantial stock buildup that stimulated production in 1990 was not repeated in 1991. In addition, coal consumption by electric utilities and coke plants dropped by about 1.8 Mt and 4.5 Mt (2 million and 5 million st), respectively. Moreover, a higher level of coal exports failed to bolster the 1991 production. Production Surface mines accounted for about 59% of the 902 Mt (994 million st) of coal produced in 1991. Underground mines produced for 41%. More than one-fourth of the total coal output was from federal and Indian coal leases. Production of all ranks of coal, except subbituminous, declined in 1991. Bituminous coal is produced mainly in the East. It totaled an estimated 590 Mt (651 million st), a 6% decrease. Production of subbituminous coal, mostly in the West, rose 3% to a record 228 Mt (252 million st). Lignite output was from Texas and North Dakota. It decreased by 1 % to 79 Mt (87 million st). Anthracite production, all from eastern Pennsylvania, fell by 17% to 2.7 Mt (3 million st).

Jan 1, 1992

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014

By B. J. K. Sullivan, Brian Hornsby

INTRODUCTION Mount Isa Mines Ltd. operates a copper and silver- lead-zinc property at Mount Isa in northwest Queens- land, Australia. Mount Isa is located in the tropics at latitude 20°43'S and longitude 139°30’E (Fig. 1). It is on the upper watershed of the Leichhardt River and at an elevation of 365 m above sea level. The average rain- fall is 360 mm/y, the greater part of which falls in January to March (the hot summer months). The mean summer temperature for these months is 30°C (dry bulb), with a maximum temperature of 43°C; the mean wet bulb temperature is 25°C with a maximum of 28°C. Mount Isa is located geologically towards the western edge of the Precambrian Shield of northwestern Queensland. This complex forms a north-tilting dissected peneplain which extends in the north-south direction for 640 km, with widths varying from 32 km to 190 km. The combination of differential erosion, regional strike, and steep dips has produced a corrugated topography of low north-south orientated hills and valleys. The field was first discovered in 1923 as a silver- lead-zinc field. Mount Isa Mines Ltd. was formed the following year and subsequently became the sole operating company on the field. Lead and copper ore have been mined and treated separately and simultaneously at Mount Isa since 1953. Intensive exploration commenced in 1954 and an active exploration program provided the justification for a series of production expansion programs in both silver- lead-zinc and copper (see Table 1 ). The most recent and largest production expansion program at Mount Isa commenced when a decision was reached in December 1969 calling for an increase in copper production from 100 000 to 150 000 t/y of blister copper. A major factor which influenced this decision was the substantial additions to the ore reserves in the so-called 1100 ore body which is a massive copper sulfide ore body with a known strike length of approximately 2500 m, a height which is variable up to 300 m, and a width of generally 300 m up to a maximum of 370 m (see Figs. 2 and 3). Host to the copper mineralization is a complex and variable rock generally called "silica dolomite." The ore body strikes 6.02 to 6.1 rad (345° to 350°), dips west between 0.78 and 1.13 rad (45° and 65°), and is truncated at depth by fault implaced basement rocks. It first occurs some 600 m below the surface and bottoms at about 1000 m below the surface. The unconfined compressive strength of the silica dolomite ore varies from 150 to 250 MPa, whereas the basement rocks, carbonaceous mylonite, slaty shale, buck quartz, and greenstone (a chloritic schist) are considerably weaker, varying in strength from 20 to 80 MPa. The distribution of mineralization within the ore body is variable, but can be considered as generally high grade at or just above the basement contact and diminishing towards the upper reaches of the ore body. The current

Jan 1, 1982

By V. F. Swanson

A mathematical model is presented which allows the free or hindered settling velocity to he calculated for any size or- shape particle in any fluid, and at any percent solids up to the maximum. The validity of the model is supported by comparing calculated velocities (or viscosities) with measured values for 1073 data points contained in 80 sets of data encompassing a range of Reynolds’ numbers, from 0.002 to 770.000. The average error was 0.69%, with an average standard deviation of 6.65%. The derivation of the model is too lengthy to include in this paper, which will specifically present the application of the model to the free settling of minerals and spheres, prediction of the friction factor in wind tunnel tests, the viscosity of suspensions of spheres, the hindered settling of mono-sized spheres and closely sized minerals, and the settling of large spheres in suspensions of small spheres.

Jan 1, 1990

By B. Cavender

Mining managers trying to rapidly reduce production costs tend to implement a traditional set of topdown managerial practices: reductions in production volume, employee layoffs, renegotiation of supplier contracts, cancellation of employee training, restrictions on travel, reductions in office supplies, and so forth. While these practices do reduce costs, the benefits are often limited in both magnitude and duration, and the workforce is usually left demoralized. Successful cost-cutters take a different approach. They make the continuous reduction of costs a priority for all members of the organization, whether managers or workers. The culture of these firms emphasizes the commitment, voluntarily given, of individuals and work groups to this goal. Cost-cutting practices often reject all of the traditional methods mentioned above, but are far more numerous, innovative and successful. This culture of cost reduction is the result of a set of leadership competencies that establish direction for the organization, align the organization's various constituencies with this direction, and motivate and inspire the organization. Cost reduction then becomes a routine task rather than a heroic achievement.

Jan 1, 2002

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By T. N. Moore, E. M. De Souza

Vibratory hand-tools can produce Hand Arm Vibration (HAV) Syndrome in their operators. This disease, often called Vibration White Finger, can cause varying levels of hand-arm discomfort and, in severe cases, impairment. In addition to the human suffering, there are also significant economic repercussions for industry. These include reduced operator efficiency, lost time through increased absenteeism and increasing compensation awards. In the mining industry, jackleg rock drills are a particularly troublesome source of hand vibration exposure. As a result, a significant amount of work has focused on redesigning rock drill handles to minimize hand-transmitted vibration. This paper details the results of a study undertaken to determine the effectiveness of using elastomer covered ("cushioned") handles in place of the standard steel design. The results indicate that, for a particular cushioned design, the overall acceleration level experienced at the hand-handle interface can be reduced by as much as a factor of three, relative to the steel handle. It is also shown that this reduction takes place predominantly in the frequency range above 500 Hz, with performance improving with increasing frequency. Qualitative evaluation of the cushioned handles by the drill operator indicates a significant increase in comfort over the standard steel handle.

Jan 1, 1992

By R. W. Bartlett

High salinity geothermal brines typically contain up to several hundred parts per million of valuable heavy metals, and because of the large potential flow of geothermal brines from future power plants, metal production as a by-product could be significant A-planned 55-MW demonstration plant near Niland, California should generate enough spent brine to contain approximately $670,000 per year in gross metal values. Lawrence Livermore Laboratory estimates (1) a Salton Sea Geothermal potential of 1300 to 8700 MW, which would translate to possible yearly heavy metal values between $5,800,000 and .$l05,000,000. Since these estimates were made on a conservative basis, this geothermal reservoir is potentially a large ore deposit. The heavy metals in order of decreasing abundance in high salinity brines from the Salton Sea geothermal field are usually manganese, zinc, iron, lead, and silver. All but manganese and iron are valuable enough to be of commercial interest. Minor amounts of copper and arsenic are also present. Although heavy metal precipitates, particularly lead, have been found in scales within pipelines and obtained from steam flashing, most of the metals remain soluble during steam production; hence removal of the valuable metals from the spent brine before reinjection in ground reservoirs is indicated. Because the heavy metal concentrations are low, a very simple and inexpensive process is required. The heavy metal value in Niland brine is only ' about $1 per 1000 gallons; see Table 1. The brine composition shown in Table 1 was taken from one of the brine samples used in our study. Projected post-flash brine from a steam plant has somewhat higher Zn and Pb values, but the gross heavy metal value is still less than $2 per 1000 gallons.

Jan 1, 1980

By John Brouwer

Through the use of good preventive maintenance procedures in which the work of both production and maintenance personnel is well-coordinated, production downtime can be drastically minimized, and costly repairs and interruptions in planned maintenance and production schedules can be eliminated. There had been some conflict in the past between production and maintenance people over the proper method of achieving maximum machine performance. The usual practice was to operate production equipment at maximum capacity for the longest possible time until breakdown occurred, and then make hurried repairs to get back into production. In most cases, these repairs involved unscheduled work and were thus performed inefficiently. Both production and maintenance have the same objective: to produce a quality product at maximum efficiency and at minimum cost. Preventive maintenance is a common tool available for both production and maintenance personnel to achieve this objective. Actually, one of the main objectives of preventive maintenance is to find any abnormal machine condition that may cause machine failure before a breakdown occurs. This makes it possible to plan and schedule maintenance work with the least amount of interruption and plan production volume with a higher rate of accuracy. Maintenance people prefer to perform this work on a scheduled basis and get away from the "crash" situation that accompanies breakdowns. They thereby increase the utilization of available manpower and machine time, prolong equipment life, and improve maintenance costs.

Jan 1, 1979

By William R. Groseclose, Cecil E. Tackett

Since 1965 when the first mole was used on Bureau work, the Bureau of Reclamation has completed 17 tunnels of over 5,000 feet in length. The longest was 12.8 miles. Total length of the 17 tunnels was 376,207 feet, or over 71 miles. The finished diameter varied from 7 feet 0 inch to 18 feet 0 inch with 82 percent (58 miles) being less than 12 feet 0 inch in diameter when lined. All of these tunnels except one are gravity flow, water conveyance tunnels with relatively flat gradient. One is a low-head pressure tunnel. All were constructed by contracts resulting from fixed-price bids. Starting in 1964 the Bureau of Reclamation initiated the practice of giving several options in the specifications on methods of tunnel excavation. Since that time, construction work has been completed on 17 tunnels. Of this number, 11 were mole excavated and 6 were excavated by conventional drill and blast methods. In general, there has been 2 feet of mole excavation for every 1 foot of drill and blast. Cost comparisons are based on only 13 tunnels because the Bureau has 4 recently completed tunnels that have pending claims; therefore, final cost data are not available. Some definite trends show from the data available; however, the number of completed tunnels in some categories is so small the results cannot really be considered a trend. As more data become available, the indications will become more reliable. The information is presented to indicate general trends and comparisons and cannot be meaningfully used for a one-on-one comparison because of individual tunnel differences not considered.

Jan 1, 1974

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By Manuel Bernales, Aldo Leon, Alexandra Carlier, Bern Klein, Andre Xavier

Mining companies and governments at both the local and national levels recognize that Participatory Environmental Monitoring and Surveillance Committees (PEMSC) are necessary mechanisms for meaningful engagement at the community level. In many cases, PEMSCs are established as volunteer initiatives by mining companies or by the mining communities themselves. In Peru however, they can also be recommended by the government as way to address social conflict. Most PEMSCs are launched while a mine is in operation and have the objective of monitoring both water quality and quantity. Many established committees are currently evolving and adopting a more comprehensive approach, as well as expanding their initial scope from a river or micro-basin focus and watchdog agenda, to a broader regional integrated resources management view. This paper examines the origins of Participatory Environmental Monitoring and Surveillance Committees in Peru. It also discusses the typology of these committees, and the scope of their work. Furthermore, it looks at the challenges faced by these committees, as well as existing opportunities for mining companies, governments, and civil society. Finally, this study presents a governance model that could contribute to the long-term existence of these committees. This discussion is further informed by the results of a national workshop that took place in October 2016 in Peru, in which over 200 representatives from 22 monitoring committees, government and mining companies participated.

Jan 1, 2017

By S. Rezaei

Moving ground in the mining industry is almost inevitable; however comprehensive awareness of these movements is necessary to mitigate risk. Monitoring of displacements caused by mining is a key tool for geomechanical risk management. Good monitoring may prevent unexpected failures and protect personnel and equipment. Many displacement monitoring techniques are available, however not all are reliable, accurate, and cost effective. Close range photogrammetry (CRP) is a monitoring method with high accuracy, reliability, and cost effectiveness; and has the ability to measure places that are inaccessible. In CRP, some series of photos are taken in different positions with different angles at different time intervals depending on the displacement rates. These photos are processed using PhotoModeler software and 3D models are made. By comparing 3D models, displacements can be measured. This method has been demonstrated at the Freeport-McMoRan Safford Mine in Arizona. A fault related instability in part of the pit is reactive to mining, and provided an opportunity to compare results between traditional monitoring methods and CRP. In this project, multiple series of photos were taken at different times using a Canon 5D Mark III digital camera, then PhotoModeler software used to make 3D models for each specific measurement event. Movement rates were determined by comparing different 3D models. These results are then compared to results of other monitoring methods to validate the CRP displacement method.

Feb 27, 2013

By G. Bryant, P. Ziemkiewicz

Acid mine drainage (AMD) from both abandoned surface and underground mines is a serious problem. The flow of water and changes in quality over time from abandoned mines is important in determining remediation strategies. Acid mine drainage from surface mines is estimated to last for 10-20 years, while estimates of acid drainage from underground mines vary from 10- 100s of years. Fifteen underground mine discharges in West Virginia were studied to compare water quality changes between 1968 and 1999 to see if our data are consistent with other studies. Each of the discharges were categorized into one of three groups: undisturbed since 1968, affected by surface mining since 1968, and reclaimed. Comparing water quality between 1968 and 1999, the discharges in the undisturbed category showed a 35 to 95% improvement in acid concentration and a 40 to 99% reduction in iron concentration. The discharges affected by surface mining showed the most dramatic improvement. For acidity, iron, and aluminum, the percent improvements were all above 44%, and in most cases in the 70 to 99% range. In the reclaimed category, one of the four discharges declined in water quality. Discharge 82 showed a 76% increase in acidity, and iron and aluminum concentrations worsened by 58 and 96%. However, discharges 15 and 74 improved in water quality with a 94% acid load improvement and a 95% iron load improvement at both sites.

Jan 1, 2000

By X. Zhu, Chen. L., R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study is to develop a suitable flow sheet to extract rare earth elements (REEs) from coal ash. A total of 14 coal samples of different ranks were examined for REE concentration, and an anthracite coal sample with the highest REE concentration of more than 700 ppm in the coal ash was selected for REE extraction tests. This paper reports on the results of the experimental program completed in the first part of the study, which included hightemperature leaching with nitric acid followed by solvent extraction tests using various organic extractants, namely, tributyl phosphate, Cyanex 572, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and their combinations. A 4×2×2 experimental design was used to conduct a total of 32 high-temperature leaching tests by varying acid molarity at four levels, solids content at two levels and leaching time at two levels. The highest recovery rates of 90 percent for light rare earth elements (LREEs) and 94 percent for heavy rare earth elements (HREEs) were obtained from the optimum leaching test conditions while maintaining impurity recovery to the leachate at less than 40 percent. D2EHPA was found to be the best extractant in this solvent extraction test series, providing an REE recovery rate of nearly 99 percent.IntroductionGlobal demand for rare earth elements (REEs) and other strategic metals is increasing rapidly due to their use in a variety of advanced technological applications, with more than 100 kt of rare earth oxides used worldwide on an annual basis. The United States has less than 10 percent of the world reserves of REE mineral deposits, and in 2013 imported more than 60 percent of its rare earth oxides from other countries, mainly China (United States Geological Survey, 2017). China’s institution of export quotas has significantly reduced supply to the United States, raising the urgency of finding new ways of producing REEs and/ or substitutes. Coal combustion byproducts, which are usually discarded as waste materials, are known to contain REEs in low concentrations that could be extracted with a suitable process flow sheet. This may be a worthwhile route to pursue, considering the short supply of rare earth minerals and the abundance of coal ash in thousands of ash ponds in the United States. More than 110 Mt of coal combustion byproducts are produced annually in the process of satisfying the country’s need for electricity (American Coal Ash Association, 2016), and less than 50 percent of these byproducts are being successfully used in various applications, with the remainder dumped as waste materials in landfills and ash ponds."

Jan 1, 2017

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By J. Potter, A. Anani, C. Antonio

This research aims to test the hypothesis that the low retention rate of women in the mining industry is caused by workplace culture and policies established due to gender segregation. A quasi-experiment is developed to determine the cause-and-effect relationship between gender segregation-inspired culture and the retention of women. The experiment considers the impact of the job type and the operational environment. The analysis provides information on factors that cause low retention of women in the industry, the extent to which gender segregation plays a role, and insights that allow actionable and measurable changes in the industry.

Feb 1, 2023