Search Documents

By M. A. Rodrigues da Silva Enríquez

One of the rare consensual points among different resource-based economic analytical approaches refers to the strategic role of rent from mineral extraction, as a decisive tool to ensure that the temporary wealth generated in the present can turn into permanent income in the future. For this reason, evaluation, distribution and use of mining rent plays a central role in the sustainable development of mining cities. Brazilian legislation provides for this at the municipal level by means of participation in the financial results of mineral extraction accomplished in these municipalities, with the Financial Compensation for Mineral Exploration (CFEM). CFEM is a type of ad valorem royalty, which charges taxes of up to 3% of the net revenue of mineral production. However, legislation does not establish how these resources should be used. Therefore, there is wide variation in the use of CFEM income among Brazilian mining cities. A study from a sample of the 15 largest mining cities in eight Brazilian states made possible identification of two main patterns with regards to the use of CFEM which were labeled "sustained use" and " the pitfall of the single treasury." In that regard, this article discusses the pressuring factors that contribute to these patterns, as well as the institutional arrangements which may be more favorable to inducing more sustained use of CFEM.

Jan 1, 2011

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By J. B. Hiskey

INTRODUCTION The extraction of gold and silver from ores, concentrates, and various metallurgical products can be achieved by a number of hydrometallurgical techniques. The solvation properties of alkali cyanide solutions on gold and silver were recognized 200 years ago. A cyanidation process for leaching gold from its ore was patented in 1887 and 1889 by MacArthur and Forrest. The solvent action of thiosulfate on gold and silver was observed over 100 years ago. Recently, several patents have been issued for processes using ammonium thiosulfate as lixiviant for precious metals, Berezowsky, et. al (1978) and Kerley (1981). Tozawa and and coworkers also examined the dissolution of gold in ammoniacal thiosulfate solution. Thiourea leaching of gold and silver initially discussed by Plaksin and Kozhukhova in 1941 but has received only limited attention since that early work. Use of thiourea as an alternative to cyanide was the topic of several papers presented at the 1981 AIME annual meeting In Chicago, Illinois. Hiskey provided a review of the fundamental chemistry of the dissolution of gold and silver in acidic thiourea solutions. Pyper and Hendrix reported on the leaching of a finely disseminated gold ore using thiourea as a lixiviant. The review article(6) previously presented was fairly comprehensive covering Important contributions to the chemistry of thiourea and the processing of gold and silver with acidic thiourea solutions. A search of the technical literature was made to determine recent (since 1981) progress and developments in applying thiourea to the processing of gold and silver. This review reveals that Soviet and Eastern European scientists are continuing to make major contributions to our understanding of thiourea/precious metal systems.

Jan 1, 1984

By R. Bhaskar

The control of quartz levels in the respirable dust requires an approach different from that used to control respirable coal dust. The unique physical properties of quartz have to be utilized when developing quartz dust control systems. Also, techniques that modify the surface properties of quartz dust so that conventional dust control measures are effective should be explored. For instance, the wetting characteristics of quartz can be modified so that the capture efficiency of the quartz dust can be improved. Foam sprays assist in modifying surface wetting characteristics. This paper summarizes the results of a study that was conducted in an operating mine to evaluate the effectiveness of a compressed air foam spray system installed under the boom of a continuous miner and directed so as to cover the pan and the gathering arm. The objectives of the study were to evaluate the effect of the foam underboom sprays on (1) the respirable dust concentration in the ambient air, (2) the quartz concentration in the respirable dust. The engineering design of the foam generation and delivery system is described in the paper, followed by a description of the mine and the dust sampling strategy. The data were analyzed to study the effect of foam on respirable dust and quartz concentrations at the miner cab, face return and the intake. The results of the data analyses and costs are presented in the paper.

Jan 1, 1991

By James M. Johnson, David Landriault, Frank Palkovits

The term “Paste Technology” was first used in the late 1980’s. It was used to describe a high fines (15 wt% or greater minus 20 microns), low water content backfill material that could be transported underground through a borehole/pipeline distribution system (4” to 8” dia.) at a yield stress similar to fresh concrete (100 to 400 centipoise). This “Paste Backfill”, unlike slurry transported backfills does not segregate into separate solid and liquid phases at low pipeline transport velocities or upon disposal into the underground stope. Paste backfills can consist solely of fine material, or can include fines plus sand and aggregate similar to a concrete mix. Pipeline transport of paste requires that sufficient fine material (minus 20 micron content) is contained within the mix to lubricate the pipeline walls to create a plug flow condition. For concrete, the fine material is supplied through the cement addition to achieve high compressive strength. For paste, the fine material is generally available in large quantities in the form of mill tailings. The paste tailings can be transported underground for use as backfill or discharged on the surface in a tailings management facility (TMF). This natural abundance of fine grained material is not exclusive to mine tailings but is common to many waste streams in many different industries. This makes the disposal of many waste materials very amenable to paste pipeline transport and placement as a non-segregating slurry. The potential use of paste technology for a wider group of waste materials was realized by these authors and others over two decades ago. Through the effort of this small group the use of paste technology has expanded over the years to become recognized as a low cost, environmentally superior, and technologically controllable method of transporting and placing specific material waste streams with a low water content and high placement density. The high yield stress nature of a paste also lends itself well to the blending of one or more coarse waste materials into the fine waste material paste stream. This allows all the waste materials to be transported by pipeline, increases their placement density; decreases the supernatant release/treatment, reduces contaminant mobilization, hydraulic conductivity and oxygen/water reactivity through encapsulation in the paste matrix. The following paper describes the present state-of-the-art use of paste technology in the world today. It also describes future uses of the technology that are under development and speculates on the overall use of the technology for waste management in the future.

Jan 1, 2005

By Jeffrey L. Zelms

There is no known, practical substitute for lead in the automobiles, communications systems, medical equipment and computers that Americans use every day. However, there are many who say lead should be stopped at its source -- banned. As America's largest lead producer, The Doe Run Company has ralized that it must do more than mine and reclaim lead efficiently and safely. It must also earn the public's consent to operate if it is to continue to be a viable business. LEAD - THE BRILLIANT PERFORMER: REFURBISHING AN IMAGE It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. I haven’t perused the course catalog for Penn State’s College of Earth and Minerals Sciences. But I strongly suspect I wouldn’t find such a course there today, either. A statement by the chairman of one of the country’s largest chemical companies leads to the point I want to make. He described his business this way. He said, “We’re a public affairs company that just happens to produce and market chemicals.” Like chemicals, minerals and mining are politicized today. To the extent that we don’t understand that reality, we don’t understand that reality – and act on it – we’re less likely to survive in this business. Some of you may well be saying to yourselves, “This guy Zelms is an alarmist.” That’s fair enough. Because it is absolutely true that there’s n o known, practical substitute for lead today. And it’s also absolutely true that, knowingly or not, Americans use lead everyday. It’s in our automobile batteries. It’s an integral part of communications systems. High tech (and low tech) medical equipment contains lead. And lead is an essential component of computer and TV screens. But even with all these uses, lead has a negative image today. An image so negative that its very existence is threatened. If you doubt that, consider these two statements made in 1989. Statement one. “It is probably reasonable to argue that exposure is the single most important and critical environmental health problem in the U.S., and possibly also the world…” Statement number two. “Many of the uses of lead should be terminated. We need to go back to the ultimate source: that is, taking lead out of the ground and putting it into the product stream and we need to turn it off at the ultimate source. Not the approximate lead in gasoline, or lead in air, or lead in food. Go right back to the source and start cranking it down." (End quote.) Those are what I call strong statements. And they weren’t made by some celebrity spokesperson for the environment like Meryl Streep. Both these statements were made by Dr. Ellen Silbergeld, whose long list of professional and academic credentials includes: o Adjunct professor and research scientist at the University of Maryland Medical School and Johns Hopkins: o Chief toxic scientist and director of the Toxic Chemicals Program of the Environmental Defense fund; o and President of the Society for Occupational and Environmental Health. If Dr. Silbergeld were the only person making these kinds of statements, it would be one thing. But she’s not a voice in the wilderness, by any means. Also for those of you who say, well since there’s no known substitute for lead, how on earth could it be banned. I refer you to a number of bills before Congress that would permit the EPA to ban any product if it is determined that its

Jan 1, 1992

By J. A. Bradbury

N. A. Degerstrom, Inc. has constructed and operated a processing plant approximately five miles north of Soda Springs, Idaho for processing a byproduct phosphate treater dust from Monsanto's elemental phosphorus plant, also located in Soda Springs. The plant is designed to produce agricultural-grade phosphoric acid, gallium, and silver. The design capacity of the plant is 54.4t (60 st) of treater dust per day, which can produce 16,326t (18,000 st) of phosphoric acid, 6,600 kg of gallium, and 6,033 kg (194,000 oz.) of silver per year.

Jan 1, 1993

By Theodore Triplett

To assess the value of various subsidence mitigation techniques, twelve linear foundations were constructed above a longwall mine. The structures were monitored during and after undermining, and footing curvatures at the time of cracking were compared with predicted values. An unreinforced concrete footing sustained substantial damage. Other footings received varying degrees of damage, with inclusion of a sand layer significantly affecting performance. A post-tensioned concrete foundation suffered minimal cracking. Also, a technique developed by the Bureau of Mines is presented for determining the subsidence, slope, curvature and strain of the ground surface.

Jan 1, 1986

By J. J. Schwoebel, M. J. Mavor

Rapid coal extraction techniques in gassy mines may strain a ventilation system if a degasification approach is not utilized. Design of mine ventilation systems requires estimates of gas emission rates from unmined coal into the existing mine workings. A degasification system for a specific property can be properly engineered to improve mining economics if the proper geologic and reservoir information is collected. This paper describes methods to determine the degasification rates for horizontal boreholes and vertical (stimulated and unstimulated) wells and the rate of gas emissions into the mine workings. The methodology is demonstrated by a specific example. Horizontal boreholes drilled in advance of mining are demonstrated to be the most effective means of coal seam degasification and reduction of gas emissions into mine workings. The significance of the paper is that few published methods for these estimates are available

Jan 1, 1991

By T. Carl Jr. Shelton

Surveying and mapping are used to locate and visually portray objects, lines, or areas in relation to a reference point or line. The actual making of the measurements to locate the objects and points falls under surveying while mapping is concerned with putting the survey information into a graphical form. Generally, the type or class of proposed survey depends on the precision required. Some surveys may need only approximate measurements which can be obtained by simply pacing or by using an ordinary measuring tape; others may require much accuracy, thus calling for the use of an engineer's transit or theodolite along with a graduated steel tape for horizontal measurements, or a level and a graduated rod for measuring vertical distances. Mapping is likewise dependent on accuracy requirements. For example, a general layout showing the relative position of surface facilities may not call for a large scale of dimension or great precision whereas for detailed work, a large scale plus care in plotting points and drawing lines and curves are important factors.

Jan 1, 1981

By J. Jordan, D. K. Denton, D. Tesarik, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health integrated the results of studies from a seismic tomographic survey, a finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. The key findings were that (1) the seismic tomograms showed that seismic velocities in rock adjacent to mine openings were low, (2) a difference tomogram in which in situ stresses on the east and west sides of the slot were compared showed that velocities increased west of the slot but decreased east of the slot, (3) geologic features (rock types and a fault) identified through geologic mapping were recognizable in the seismic tomograms, (4) ultrasonic velocity measurements on the rock cores agreed with seismic velocity measurements in the tomograms, and (5) results from a finite-difference analysis compared well to the seismic tomograms west of the slot but not east of the slot. The significance of this research is that seismic tomography is a useful tool for determining relative stress in underground pillars.

Jan 1, 2004

By D. C. Rotherham

The Kidston gold discoveries were originally made about 1907, and by 1934, 1.76 Mg (62,000 oz) of gold had been produced from placer and lode mining of higher grade, most¬ly oxidized gold ore. As mining in the lode ore penetrated deeper, costs increased and the world gold price stagnated. The lode or underground production averaged close to 6.9 g/t (0.2 oz per ton) Au for the 201 kt mined. No mining or development took place from 1934 until 1965. Kidston's high grade ores were exhausted by 1934. From 1965 to 1976, exploration had developed 3 Mt of about 3 g/t (0.88 oz per ton) Au. Placer Pacific acquired rights to the property in 1976 and began a geologic and engineering study of the district. It was clear that the deposit had the potential for becom¬ing a large-tonnage, low-grade producer. However, explora¬tion had to discover the tonnage and grade and engineering needed to solve the obstacles of production costs. Bulk material handling problems were addressed by Placer's wide experience in open pit mining, and the increase in work index accompanying deeper ores was handled by Placer's metallurgists. The matter of power for the operation was solved by engineering studies. These showed that power could be generated and brought in economically. The price of gold also increased after 1976, and this helped in the economic analysis. The Kidston discovery since 1976 is really a combination of good exploration geology and careful engineering plan¬ning that overcame the obstacles presented by ore characteris¬tics and the location of the deposit. The attached paper by Harry Mustard is an extract of his honors thesis and explains the deposit geology.

Jan 1, 1990

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The U.S. Bureau of Mines and AMAX Coal Company have studied surface coal mine overburden blasting near four steel and one PVC pipe-line of 15 to 5l-cm diameter, monitoring vibration, strain, and pressure. Unlike tests simulating construction blasting, these were up to 1000 kg per delay in 3l-cm blastholes. Worst case comparisons showed that 12.7 cm/s blasting vibrations produced strains about 1/4 that of pressurization and 10-18 pct of the ultimate tensile strength. No failures occurred from blasting as close as 15 m which produced vibrations over 60 cm/s.

Jan 1, 1994

By Mahesh C. Jha

Cyanidation has established itself as the main process for extracting gold from ores in this century. However, many ores exhibit refractoriness to the conventional cyanidation process. The main cause of the refractoriness is generally the presence of carbon, tellurium, and sulfides, particularly those of antimony, arsenic, and iron. The problem is usually solved by either modifying the cyanidation conditions or providing an oxidation pretreatment. This paper presents results from studies that help in understanding the causes of refractoriness of various gold ores. This is followed by a discussion of many processes that have been developed to solve the problem such as intensive cyanidation, pressure cyanidation, carbon-in-leach cyanidation, and pretreatment processes such as roasting, chemical oxidation, autoclave oxidation, and bacterial oxidation.

Jan 1, 1986

By James A. Finch

The Gaudin lecture is devoted to fundamentals. Given my involvement with column flotation over the last 20 years, this is my topic. I have tried to identify spinoff basic research and provide a personal list of favorites. Two are selected for discussion here. They are single bubble rise and bubble surface area flux. The rationale for such work, as well as some of the findings, are reviewed. Support for fundamental work seems as volatile as the economy (and the link is probably not coincidental). I hope some utility to the minerals industry is evident in the text. Column flotation in its current form originated in the early 1960s. The method was invented by Boutin, patented by Boutin and Tremblay and pursued doggedly by Wheeler. Their aim was to overcome the problem of mechanical entrainment of fine particles in the water carried by the bubbles, which they were convinced contributed to lowering flotation concentrate grades (Wheeler, 1988; Finch and Dobby, 1990). The solution was a combination of columnar geometry, the addition of wash water into a deep froth and the maintenance of an excess of water to the tailings, as compared to the feed (a so-called positive bias). Success at Les Mines Gaspe, Quebec, on cleaning Mo in the early 1980s signaled the start of industrial acceptance, making the column one of the flotation machines of choice today. Over the next 20 years, column applications mushroomed to cover virtually all mineral commodities, as well as nonmineral applications such as soil decontamination, deoiling of water and deinking of recycled paper. In the wake, research groups are continuing to probe the fundamentals, conferences and workshops have been transferring the technology and specialist companies have emerged to service the demand. Innovations were triggered as problems arose (for instance, in gas injection systems) and novel flotation cells, much in vogue in the 1990s, had the door opened. Mechanical cell manufacturers have not been idle - there is nothing like competition to provoke a fresh look at an established business. Flotation-cell technology has probably not seen so much activity since the patent rush in the early days of flotation, which occurred around the turn of the century. For an industry often considered reluctant to risk innovation, this is not a bad record. A good idea will find a place, but patience (not always an innovators strong suit) and careful preparation are required. Two books (Finch and Dobby, 1990; Rubenstein, 1996), three symposia (Sastry, 1988; Agar and Huls, 1991; Gomez and Finch, 1996), and a series of reviews (Dobby and Finch, 1991; Finch and Dobby, 1991; Finch, 1995; Finch et al., 1995) document the period. Like many good ideas, column flotation has been overexposed, and there have been disappointments. In a recent example, columns performing scavenging duty were replaced by mechanical cells (Chong et al., 1998). The further applications stray from the original - to

Jan 1, 1999

By S. Zaman, F. F. Aplan, Franklin T. Davis

This section deals with the oxides of heavy metals, namely, columbium and tantalum, rare earths, chrome, manganese, titanium, tin, and tungsten. Table I contains the production figures for each of these commodities in the US and in the world in 1977. Specifications for concentrates are also summarized as well as prices for concentrates in 1977. In each chapter an attempt has been made to describe the more common commercial mineral involved with the commodity and the processes used to recover and concentrate the minerals, as well as geographical areas where these processes are utilized.

Jan 1, 1985

By D. R. McMullin

The purpose of this paper is to provide a method for mine planners and engineers to evaluate on a conceptual basis if a shaft or a ramp is most suited for their particular underground access requirements. Mine planners and engineers are often raced with the decision of choosing which method of underground access is best suited for their particular requirement. Underground access can be provided by a shaft, ramp, adit, or slope for either exploration and/or actual production operations. This paper will focus on the construction cost and schedule differences between sinking a shaft and excavating a ramp which are currently the most typical access alternatives used in the western United States. It would be wrong to state that one method is superior to the other in every case. There are many variables to be addressed, and the degree of sensitivity of each of them will eventually dictate which method is the most suited to the particular circumstances. This paper compares the construction cost and schedule or sinking a shaft to excavating a ramp at different depths given different ground and hydrological conditions. This comparison provides mine planners with "rules or thumb" that may be applied to the access selection process.

Jan 1, 1994

By Robert J. Mac Kinnon

A moving grid finite element model for the analysis of transients in a rock mass surrounding an underground coal conversion cavity is presented. Major model components are outlined, including a special element formulated to account for internal discontinuities. A numerical example is described.

Jan 1, 1986

By W. A. Lawruk, L. J. Wilson, D. E. Stief

The Tower mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine and its operation, application, and performance for wet grinding.

Jan 1, 1988