Search Documents

By K. Bunney

A high-pressure laboratory elution rig was commissioned to simulate industrial Zadra and AARL elution conditions for the stripping of gold, silver and mercury from loaded activated carbon. It was found that cyanide was essential for the efficient elution of both mercury and silver, while gold was found to elute most effectively in hot, low-ionic strength solutions. Therefore, the standard AARL-type elution, which implements a cyanide soak and water elution, results in a lower recovery of mercury and silver from the carbon. No single set of conditions was found whereby gold, silver and mercury can all be effectively eluted in a single step. However, sequential elution conditions can efficiently recover all metals and provide a potential approach for separating these metals.

Jan 1, 2010

Fundamental results obtained from research on the properties of the edge surfaces of kaolinite particles (~500 nm) are reported. Of particular significance was the development of the experimental protocol. Well-ordered kaolinite edge surfaces were prepared as an epoxy resin sandwich structure having layered kaolinite particles in the center of the epoxy resin sandwich. Images of the sectioned kaolinite edge surfaces were examined by atomic force microscopy (AFM), and the average thickness of kaolinite particles in this study was determined to be 38.3 nm ± 11.7 nm. Furthermore, the surface charge of the kaolinite edge surfaces was evaluated with a super sharp Si tip. The point of zero charge (PZC) of the kaolinite edge surface was determined to be below pH 4, in contrast to the traditional view that the edge surfaces of kaolinite particles may carry a positive charge at pH 4. This lower PZC of the kaolinite edge surface was attributed to the lack of isomorphous substitution in the silica tetrahedral layer when compared to the PZC for the muscovite edge surface. Our results are consistent with the particle aggregation and flotation behavior of kaolinite, and should provide the basis for improved flotation strategies leading to the efficient recovery and utilization of mineral and energy resources.

Feb 23, 2014

By A. J. Hendron, L. L. Oriard

INTRODUCTION Controlled blasting is used at some time during most civil engineering projects where there is rock excavation. Controlled blasting is often necessary because the blasting must take place in the near proximity of adjacent structures. In other instances, the blasting is controlled because a smooth perimeter is desired to minimize rock support and overbreak. The construction of tunnels and shafts for subways, rock excavations for foundations and the excavation of road cuts for interstate highways, sometimes require blasting operations which must be conducted in an urban environment. Unfortunately, blasting operations produce unwanted sounds and vibration along with their beneficial effects. Thus, in the writing of specifications for blasting in an urban environment, potential damage to adjacent structures by ground vibrations must be considered, possible damage to windows from airblasts must be considered, potential damage from fly rock must be considered, and the discomfort to people from ground vibrations, airblast, and noise must be taken into account. The contractor or the owner's engineer is faced with determining the maximum weight of explosives which may be detonated without damage to structures on adjacent property. If the weight of explosive is overestimated, the resulting damage to adjacent structures may result in costly losses. But, if the engineer or contractor is too conservative, and the weight of explosive becomes too restrictive, progress of the project may be curtailed and the cost of excavation will increase accordingly. The potential for damaging adjacent property is becoming more important in construction operations today. In the past, the plaintiff had to prove negligence in some states in order

Jan 1, 1997

By G. T. Adel, J. D. Miller, C. L. Lin

In view of the success of recent laboratory studies using X-ray computed tomography (CT) to determine coal washability and with the availability of high-speed CT systems, it now seems possible to design an on-stream washability system for the control of coarse coal-cleaning circuits. Design features for such a system are examined and possible control strategies are discussed for different applications.

Jan 1, 1995

By Xinghai Lei, Yuqi Shang, Guiming Li, Lu He

There are many factors affecting the stability of open-pit mine slopes, among which slopes with soft interlayers have become an important factor inducing deformation and instability due to their poor mechanical properties. In this paper, for the destabilization of a slope with soft interlayer under rainfall infiltration in an open-pit mine in Zhejiang Province of China during the rainy season, a sudden change of displacement at the monitoring point and the formation of a continuous plastic deformation of the slope are proposed as the criteria for slope destabilization through the establishment of a rainwater seepage-stress coupling model combined with the strength reduction method, and by using COMSOL Multiphysics finite element numerical simulation software to establish a three-dimensional numerical model based on the actual mining slope conditions. The safety principle is introduced through the strength reduction method to analyze the stability of the slope with soft interlayer under the coupling effect of seepage and stress. The safety coefficients of the slope with soft interlayer are calculated by using Numerical methods under the coupling effect of seepage and stress. The influence of rainfall intensity and duration on the stability or safety factor of the slope with soft interlayers was studied through analysis of stress, saturation, displacement, and pore pressure evolution. The mechanism of rainfall affecting slope stability was investigated, and the findings were validated using an engineering case study of a slope with a soft interlayer. The findings show that rainfall intensity is the main factor affecting slope stability in the open-pit mine slope with soft interlayer. The higher the rainfall intensity, the faster the shallow soil forms a saturation zone, whereas soft interlayers speed up the process and endanger slope stability. The slope prevention and control technology of the prestressed anchor cable (rod) framework was proposed based on the slope management construction conditions of the mine, and the effectiveness of the measure was verified through on-site industrial tests. The research findings provide a reference for preventing and controlling slope with soft interlayers in open-pit mines under similar conditions.

Feb 20, 2024

By Jr. Smith

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915 In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various borate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 400 feet (121.9 m) deep, 3000 feet (914.4 m) long and 1000 feet (304.8 m) wide. The borates in the Boraxo pit consist primarily of three minerals. These are about 50% coiemanite (C2B6O11' 5H2O), about 40% probertite (NaCaB5O9.5H2O), and 10% ulexite (NaCaBcO9.8H2O). The colemanite, along with boric acid and high-grade coiemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder. This provides the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content.which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations.

Jan 1, 1978

By Betty L. Gibbs

What does the information age mean to mining companies? The perception of greatly increased access to information is based on modern communications through ‘smart’ fax machines and computer networks. Computer media allow us to `talk' to the President or to a sister in Australia. If we need data to help put together a mining permit, we can find that data somewhere on computer media. The vast amount of easily accessible information quickly overwhelms us. To avoid `information burnout,' we must learn to target searches and be able to discriminate between dross and information that is useful to our goals. If you watch commercial TV, you have learned to screen out most product commercials. A similar screening process must be applied to computerized information sources. You may need to sort through a lot of irrelevant information before finding the pearls you are looking for. ‘Smart’ fax machines can send information with no direct human intervention. MINES FaxBac, for example, from the US Bureau of Mines instructs you to enter four-digit numbers to have particular reports sent directly to your fax machine. Software vendors use a similar system to supply information about their products. You select an item by number, and the related brochure is faxed to your machine. To compete, the industry must maintain access to as many information sources as possible. The availability of computers and software for almost every conceivable application allows us to accomplish work faster than we ever thought possible, even as recently as 10 years ago. Most mining companies have become aware that doing geology, reserves, mine planning and other technical tasks completely by hand is much too slow. The world moves faster, drilling happens faster, mining happens faster, all related activities happen faster. We no longer have the manpower or time to keep all maps. calculations and records up to date.

Jan 1, 1994

By E. R. Mueller

The natural lives of machines and components vary tremendously! Maintenance managers struggle constantly to maximize their equipment lives while minimizing their maintenance costs, but they normally lack the tools and techniques they need to do this properly. This paper proposes a methodology based on probabilities of failure and expected values for repairs that recognizes the variation among individual machines and components as well as the high costs associated with catastrophic failures. It enables a user to determine the optimum change-out intervals for many types of equipment. The approach proposed here is sophisticated enough to be reliable but simple enough to be applied by the maintenance staff on the shop floor. It will complement existing preventive and predictive maintenance programs.

Jan 1, 1995

By J. H. Bassarear, P. F. Thomas

Large-scale equipment can reduce both capital and operating costs for concentrators. Large semiautogemus (SAG) mills can be effectively utilized in big mills but they must be kept fully loaded to tab advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semiautogemus mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4476 kW (6000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 t/d (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and jive variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1987

By Stephen C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined utilizing underground workings during 1980-82 by Esso Erz GMbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceived as a cost effective procedure to answer questions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gaga probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 as thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1983

By Dana A. Echter

The Paso Diablo coal project is located in the Guasare Basin in the northwestern region of Venezuela near the border with Colombia. In 1987, Carbones del Guasare SA, a joint venture comprised of Carbozulia and A.A. Antilles Coal (an Arco and AgipCoal joint venture) was formed to develop the Paso Diablo coal reserves for world markets. Regional drilling has indicated a coal resource of more than 6 Gt (6.6 billion st). Further exploration has delineated the Paso Diablo deposit as an area particularly suited for cost-effective surface mining. The calculated economically minable reserves of this area (200 Mt or 220 million st) and the coal quality characteristics are based on extensive core drilling programs. Initial coal mining operations began in August of 1987 and the mine is presently producing at a rate of 1.5 Mt/a (1.65 million stpy). The coal is hauled about 85 km (53 miles) to a barge loading terminal at Santa Cruz de Mara using highway-type haul trucks. When the coal reaches the terminal, it is loaded into barges and then transloaded onto ocean-going vessels with barge mounted

Jan 1, 1990

By K. G. Colman

Introduction This text is intended to provide the operator and turnkey contractor with the basic data for sizing vibrating screens to be used in ore crushing plants. The basic capacities, modifying factors, etc.. used in the area requirement calculations were developed empirically and modified to their present values based upon years of practical applications. It must be pointed out that screening is much more of an art than an exact science; however. the information presented here should provide for reasonably accurate screen sizing when applied to many metallic ores. Types of Screens There are two types of screens which can be used for strictly sizing applications. These are two- and four-bearing screens; both are inclined circle-throw machines. Two-Bearing Screens The motion of a two-bearing screen is generated by unbalanced weights attached to the vibrator shaft. The body of the machine is usually supported by steel coil springs (see Fig. 8). The main advantage

Jan 1, 1985

By Frank F. Aplan, Edward C. Jr. Dowling, Richard R. Klimpel

Thirteen kinetic models that mathematically describe the flotation process have been statistically evaluated for the flotation of copper, lead and zinc ores. Comparisons have been made for a variety of circuits involving roughing, cleaning, scavenging and regrind followed by cleaning. Variations in collectors, frothers, depressants and activators have been considered. Based on the statistical criteria used for the evaluation, and the reagent, circuit and ore variations studied, the most reliable flotation models have been identified and subsequently used to characterize the metallurgical results.

Jan 1, 1986

By J. T. Carlson

Dolomite is an objectionable impurity in phosphate ores, due to its MgO content. Even though dolomite and apatite liberate at a coarse size, the very similar densities of dolomite and apatite makes density separations difficult. However, if operated correctly, jigging can be a very efficient process. This has led to the development of a unique laboratory scale jig that allows for easy alteration of effective jigging properties. Key jigging parameters have been investigated for the separation of dolomite from phosphate ores. It was found that a pulsation rate of approximately 200 pulses/minute worked best for separating dolomite from apatite.

Jan 1, 2010

By P. Zhang

A 1989 FIPR characterization study of the future phosphate resources in Florida showed that MgO would be a problem with both the pebble and concentrate as phosphate mining moves deeper. Since the ratio of concentrate to pebble will become higher and higher in the future, reducing Mg content in the concentrate by a small margin would allow blending of a large portion of the high-dolomite pebble. This research was conducted based on that logic. The following six approaches were tested for reducing MgO content in the flotation concentrate: (1) Adding a dolomite depressant in the rougher flotation step; (2) Dolomite flotation on the rougher concentrate with and without grinding; (3) Dolomite flotation on the cleaner concentrate with and without grinding; (4) Scrubbing the flotation feed; (5) Scrubbing the rougher concentrate; (6) Scrubbing the cleaner concentrate. Successful methods include adding a dolomite depressant in the rougher flotation, dolomite flotation on the cleaner concentrate with grinding, and scrubbing the cleaner concentrate in quartz sand. These techniques could reduce MgO content in the final concentrate by 20-40%. The flotation process could achieve a concentrate with the lowest MgO content, but it is the most expensive approach. Adding a dolomite is inexpensive and easy, but the effect is limited. Overall, scrubbing may be the most promising technology for this purpose.

Feb 23, 2014

By Norman K. Olson

A geologic investigation of mineral resources in South Carolina first began in 1825 when the General Assembly authorized Lardner Vanuxen to conduct a "Geological and Mineralogical Survey of South Carolina." Vanuxen, South Carolina's first State Geologist, reported in 1826 on the limestones (marble) of the Piedmont which during those early years, were burned in many shall, scattered kilns in the region wherever suitable raw material was available. He also mentioned the possibility of using marl from the Atlantic Coastal Plain province for direct application and enrichment to the soil. Since before the year 1844 industrial minerals in South Carolina have been commercially produced literally from A to Z, asbestos to zircon. The first pub¬lished reports of actual commercial production, not just an occurrence, are referenced in Table 1 for 33 known industrial minerals and rocks in South Carolina. Known or suspected occurrences of undeveloped non-metallic mineral resources in South Carolina await future verification by geologic mapping, sampling (including coring), possible beneficiation, and market analysis. These industrial minerals and rocks include, but are not limited to, special, clay minerals (e.g. bentonitic clays, zeolites and others), sillimanite, argillite (lightweight aggregate), kaolin (alumina) and marl (underground storage and tunneling medium). In addition other non-metallic minerals, once mined but still worthy of reconsideration, include topaz (industrial), heavy minerals, barite, feldspar, and monazite. Finally, possibilities for new reserves, as an expansion of existing mine output, might develop for fuller's earth, limestone (lime), sericite (finely divided mica), vermiculite, kaolin (paper coating and filling, other filler), and metallurgical gravel. Official South Carolina data from the U. S. Bureau of Mines for 1974 indicated a total value of mineral production of $105.2 million. During 1974 production consisted of cam-on clays, (brick and tile), fuller's earth, kaolin and vermiculite

Jan 1, 1977

By Dhananjay Kumar

In past, no serious attempts have been made to study the effects of operating environments on performance characteristics of a mining system. In this paper, proportional hazards model (PHM) analysis technique is introduced which can be used to analyze the effects of operating environments on the performance of a mining system. It can be used to select suitable materials, manufacturers or designs of items for a particular working environment. In this paper some applications of the PHM are discussed with examples from a Swedish mine. Its application for decision making in maintenance is also discussed.

Jan 1, 1992

By D. W. Wu, M. T. Haque

A novel impedance probe was commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mudline, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mudline information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are reviewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2002

By Mingfei He, Jianhua Chen, Yingchao Liu, Yuqiong Li

Pyrite is one of the most common sulfide minerals on earth, which is usually grown with chalcopyrite and other sulfide minerals. In flotation practice, pyrite from different mines or different sections in a same mine may have different flotation behaviors. This is because the pyrite crystal contains lattice defect, including ionic vacancy and lattice impurity. The present work investigates the effects of three typical 3d transition metal (Co, Ni, and Fe) on the adsorption of CH3OCS2 −, OH−, and CN− on pyrite surface by density functional theory (DFT) calculations. Calculated results show that Co impurity reduces the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite, while Ni and Cu impurities significantly increase the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite. Co impurity has small influence on the adsorption of OH−, but Ni and Cu impurities significantly increase the adsorption energies. Calculations on Mulliken charge population of Co2+, Ni2+, and Cu2+ indicate that the Mulliken charges of Co2+, Ni2+, and Cu2+ after OH− adsorption are more than those after CN− adsorption. This suggests that the ionic property of the M-OH- coordination bond is greater than that of M-CN- coordination bond, while covalent bonding of M-CN- coordination bond is greater than that of M-OH- coordination bond. The adsorption results are discussed based on coordination field theory (CFT).

Oct 6, 2020

By Keith Whitworth

The USSR, over the last 20 years, has continued to increase its out-put year by year and it is now almost four times what it was at the end of the Second World War. In 1975, it exceeded 700 million tons of run-oi-mine coal (all ranks) which amounts to over 20 percent of world output. This rapid progress has been due to modernization of the industry, by means of increased mechanization and automation and the development of new machines and systems for underground workings and by the expansion of open-pit workings and the development and implementation of larger earthmoving machines.

Jan 1, 1977