Search Documents

By Kim A. Lapakko, William W. III White

The ASTM standard method D 5744-96 was developed to provide a well-defined kinetic test protocol, conducted under controlled reaction conditions, with the intent of generating reproducible results. The US Bureau of Land Management, American Assay Laboratories, and the Minnesota Department of Natural Resources cooperated in a intralaboratory and interlaboratory testing of the protocol. Intralaboratory testing was conducted on duplicate samples of gabbro (8) and siltite-argillite (5) rocks for periods of 20 to 125 weeks. The difference between replica& intralaboratory pH readings on drainage from the gabbro for the drip-trickle leach alternative typically did not exceed 0.1 units, although differences as high as 0.4 units were observed. The difference from the mean for rates of sulfate, calcium and magnesium release was typically within 10%. Intralaboratory results for the siltite-argillite samples were generally similar, although a one unit pH difference was observed for one sample. Three different laboratories tested a gabbro sample for 125 weeks, with a maximum difference from the mean pH of 0.5 units. The percent difference from the mean for sulfate and calcium release rates was typically within lo%, although values as high as 30% were observed. Data on intralaboratory and interlaboratory agreement on the flood rinse alternative of the method were limited. Replication on the sample tested was comparable to of better than that observed for the drip-trickle method testing of the same sample.

Jan 1, 2000

By F. Varley

Researchers from the National Institute for Occupational Safety and Health (NIOSH), in cooperation with mine operators, conducted a study of heat stress exposures among mine rescue workers in underground mines. Mine rescue workers face extreme heat loads as they enter hot and poorly ventilated environments, particularly when they are wearing breathing apparatuses. The burden of wearing a closed-circuit breathing apparatus (CCBA), the inability to drink fluids for extended periods of time, and the potential for ventilation disruptions and fires combine to increase the risk of heat illness during a response to an emergency. In this research, ambient environmental conditions and heat strain indicators were measured using conventional ventilation monitoring tools during mine rescue training exercises. Heat strain was measured with an ingestible temperature-sensing pill that measured core temperature continuously. In addition, a heart-rate monitoring chest strap was used to indicate physical strain resulting from physical activity and heat. Both core temperature and heart rate data were trans-mitted to a remote recorder worn by a rescuer and time-stamped. Team activities were also observed to determine the contribution of work rate to a person’s total heat load. The effectiveness of several engineering controls, such as cooling the air inhaled by rescuers through an apparatus, wearing cooling vests, and supplying water through the CCBA masks, were investigated. Administrative controls, such as limiting the duration of exposure and controlling the work rate through forced-rest regimens, were also evaluated. Results to date are discussed, and tools for evaluating team condition and estimating the length of time it would be safe for rescuers to work are proposed.

Jan 1, 2004

By Ken Deter

I have some general comments on optimizing profitability based on working in heap leach operations in tropical environments. Many of my planned comments this morning have been stated earlier in the Conference. I get the opportunity to say only a few words, and follow up on some specific comments and concerns. In normal operations, stack the ore higher, where possible. The surface area of the stacked ore controls the total solution volume that can be sprayed on the pad at a specific time period. With higher lifts, solution will contact more ore particles as it percolate through the lift, and therefore the solution grade flowing through the base will be increased, whether it is freshly stacked or almost completely leached ore. This also allows more tonnage to be stacked per lift on the pad, decreasing conveyor movement and downtime. Increasing from 6 to 8 meter (20 to 26 feet) lifts have worked successfully, and some mines are using 10 meter (33 feet) lifts in 10,000-15,000 dmtpd plants. The same concept will work with smaller plants, but initial 6 meter lifts should be used until the start-up period has shown the leaching is working as planned. As the stacked ore lifts get higher, the solution flowing through the highest lift is diluted by solution retained in the lower ones. Eventually no real increase is noted from putting fresh ore in service, and gold production rate suffers. To address the dilution problem, an HDPE liner should be installed between each 2 to 4 lifts, depending on each site specific lift height, recovery, % slump in the lift, recovery rates, and grade treated, among others. The surface of the previous lift should be leveled and sloped to control the effluent draining from the planned lift, then the liner is placed, including berms and discharge pipes. The intermediate HDPE liner does not need to be completely sealed as would be the case with the base liner, and can accept some solution penetrating into the lower lifts. A one-mm (40-mil) thickness liner can be used. This intermediate liner allows the upper lift(s) higher-grade effluent to report to the pad discharge point. This will maintain higher gold solution grades going to the ponds. The slopes of the previous lifts should not be covered with HDPE in this concept, and precipitation falling on the lower lift slopes and benches can be directed to barren or surge ponds.

Jan 1, 1999

By W. J. Martin

At the termination of mining, the quality of ground water in the ore-zone aquifer must be returned to a condition predetermined by the permitting agency. To immobilize the redox-sensitive elements (e.g., uranium, arsenic, selenium, molybdenum), it has been suggested that a reducing agent be circulated through the leached ore zone. We have conducted laboratory experiments to test the ability of sodium sulfide as such a reducing agent. Sodium sulfide lowered the redox potential of the effluent such that insoluble minerals containing the redox-sensitive elements should be stable. The uranium concentration of the solution decreased by more than three orders of magnitude. In column experiments, by the time ten pore volumes of the sulfide solution had flowed through, sulfide minerals were forming. The experimental results indicate that the addition of sodium sulfide should cause the chemical reduction of the leached sediments, thereby producing long-term stability of the ground-water/sediment system.

Jan 1, 1986

By R. P. King

Knowledge of the behaviour of flotation machines had developed and increased considerably over the last few years. Although much work remains to be done on the study of the fundamental processes that influence the collection of hydrophobic particles at an air-water interface, there is enough information to permit the building of realistic models of the gross flotation behaviour of various ores. These models serve as an ideal base for the development of simulation techniques for the steady-state behaviour of entire flotation plants that consist of a large number of individual flotation machines. Simulation techniques have a very real role to play in assisting with the design of new plants and in improving the operation of exisiting plants. Recently, highly efficient data-logging systems have been introduced on flotation plants. These systems are based on the on-line measurement of volumetric flowrate, pulp densities, and metal contents, and they generate enormous quantities of information regarding the operation of the plant. Unfortunately, this information is largely wasted at the present time because efficient data-reduction techniques, although available10 are not in common use. Simulation techniques play a central role in such data reduction because they form the essential link between the fundamental kinetic flotation processes on the one hand and the plant data on the other.

Jan 1, 1974

By Sufi Md Gulzar, L B. Roy

Rock engineering tasks like tunnelling, dam and building construction, and rock slope stability rely heavily on properly estimating the rock’s uniaxial compressive strength (UCS), a crucial rock geomechanical characteristic. As high-quality specimen are not always possible, scientists often estimate UCS indirectly. The primary objective of this paper is to assess the efficacy of long short-term memory (LSTM), K-nearest neighbour (KNN), a combination of particle swarm optimisation (PSO) with an artificial neural network (ANN), and adaptive neuro-fuzzy inference system (ANFIS) to estimate the UCS of sandstones from Jharia, Dhanbad, India. Point load index (PLI), porosity (n), P-wave velocity (Vp), density (ρ), and moisture content (%) are the parameters used for the present study. Finally, a comparison was made between the various prediction algorithms outputs. The findings of the study validated the effectiveness of computational intelligence methods in forecasting UCS compared to other models used in this paper. The KNN achieves overall the best results, with an R2 of 0.95 for training, 0.94 for testing, and an RMSE of 0.03 for training and 0.05 for testing.

Nov 23, 2023

By R. L. Grayson, R. C. Althouse, M. J. Klishis

The health and safety of employees, efficiency of the operating system, and production are paramount goals in underground coal mining. The section foreman assumes responsibility for making his part of the total system function to meet these goals. However, section foremen often have not been prepared to assume the full range of their responsibilities upon becoming a supervisor. This paper addresses the full range of section foreman responsibilities and concomitant authority. Management principles that must be mastered by him are presented, and performance expectations as well as criteria for their evaluation are examined. The benefits realized from effective foreman training are discussed.

Jan 1, 1987

By Manfred Jaeger, Klaus Ertmer, Walter Dietrich, Jochen Greinacher, Wilhelm J. Kogelmann

In Europe, novel low-cost excavator-mounted Multi Tool Miner (MTM) systems, consisting of cutter head, hammer, bucket and drill attachments permit one unit to perform multiple tasks replacing several purpose-built machines. At the Weser Tunnel in Germany, cross-passages between the twin tubes were excavated in frozen ground with a remote-controlled mini-excavator equipped with a quick-change cutter head, ripper tooth and bucket. In Switzerland at the N2 interstate near Basel, W. Dietrich AG enlarged a 2-lane tunnel to three lanes with a cutter head mounted on a special excavator. Blasting and heavy hammers were not permitted due to the closeness of the “live” twin tube. At the N20 Zurich bypass, the Joint Venture of Jaeger, Frutingerand AHB excavates highway tunnels, some with extremely large cross sections, conventionally. A cutter head mounted on an excavator removes the rock shattered by blasting precisely to the pay line, thus preserving the rock’s self-supporting capacity preventing subsidence and damages to water resources and buildings on the surface under low overburden.

Jan 1, 2003

By Jacques B. Wertz

It is well known that the major fractures and lineaments presently recorded in Western North America are preferentially oriented along a general northwest direction (Figure 1). There are other features, however, more subtle, more elusive as a rule and which can only be inferred, occurring at right angle to this broad NW direction. It is intended a) to examine some of these NE or transverse trends, b) to compare these regional NE breaks to similar ones that transversally cut through the eastern part of the European Tethys, more specifically in Iran and Turkey, and c) to study their potential relationship to mineralization in both areas.

Jan 1, 1973

By J. A. Harrison

Most coal being used in the United States has been subjected to one or' more processes of coal preparation. The physical and chemical characteristics of a coal have a marked influence on the ultimate uses that coal may have. The selection of the proper preparation processes may similarly be important in producing the best practical coal product for any particular use. The physical composition and distribution of physical constituents in the coal will partially determine the efficiency of the preparation process chosen and conversely distribution and concentration of coal macerals will, to a degree, be controlled by the preparation process. A number of preparation processes have been evaluated to determine this interrelation. If a coal having' certain specifications is desired, these evaluations trill assist in providing information needed for the production of this coal.

Jan 1, 1962

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009

By Andre C. Zingano

It is a very difficult task to estimate the immediate roof and support behavior in a room-and-pillar mining section in the initial phase of the mining project. There is little information available at this phase, and it is restricted to geomechanic characterization of the rock layers from cores samples, and the in-situ instrumentation of experimental entries and intersections. Even being a pilot excavation for roof support test a good indicator for the behavior of the immediate roof, its behavior for a full excavation mining section is different from a single intersection of two entries, mainly because the stress redistribution caused by the multiple entries excavation and face advance for a full excavation section. The objective of this paper was to calibrate a 3-D numerical model of an experimental intersection, based on the in-situ instrumentation of an experimental intersection excavation, and the geomechanic description of the rock layers. The numerical model was built with the same specifications as the excavation test, including the entry geometry and roof support. The numerical model calibration was based on wire extensometers that were installed at different positions in the roof of the pilot excavation, and on the geomechanic characterization of the rock layers that form the roof, coal seam, and floor. Therefore, it is possible to estimate whether the roof support specification adopted in the test phase will be good enough for the development of the entire mining section.

Jan 1, 2009

By R. E. Scheffel

In February, 1976, Ranchers Exploration and Development Corporation obtained an option from Foote Minerals, Inc., to evaluate reprocessing of two uranium tailing piles. Foote received ownership of the Naturita and Durango tailing piles in 1967 through the purchase of Vanadium Corporation of America. The option was exercised in November, 1976, after initial testwork proved that a viable extraction technique existed. Preparation for production at Naturita began immediately with engineering and en¬vironmental permitting proceeding simultaneously. Production began in December, 1977, just 22 months after acquisition of the property and-was completed 17 months later.

Jan 1, 1981

By Kaige Zheng, Hongwei Wang, Tong Wang, Yanjun Li, Yongping Wu, JIANQIANG JIAO, Baolin Jiang

Due to the influence of economic development on the demand growth of coal resources, many mines in China have gradually entered deep mining. When the roof of deep coal seam is hard rock, it is easy to cause strong ground pressure with the advance of the working face, which seriously threatens the safety of coal mining. Taking 31,104 working face of a mine as the engineering background, this paper studies and compares the deformation characteristics and stress transfer evolution law before and after the presplitting of the hard roof through the combination of physical similarity simulation, numerical calculation, and field measurement, based on the analysis of the interaction relationship between the breaking and collapse of the composite hard roof, and verifies the treatment effect of hydraulic presplitting through field measurement. The results show that: (1) In the early stage of mining under the composite hard roof, the lower roof is mainly subjected to tensile failure, the voussoir beam structure formed is relatively unstable, and the stope is prone to impact. When the mining distance of the working face is large, the breaking rotation of the upper hard roof voussoir beam causes pressure damage to the lower hard roof, causing the lower hard roof voussoir beam structure to slide and lose stability, resulting in strong ground pressure in the working face. (2) After presplitting of composite hard rock stratum, in the early stage of mining, the range and degree of rock stratum damaged by presplitting are small except for the hard rock stratum itself, and the presplitting effect is not significant. When mining to the first square position, the roof is damaged in advance by presplitting, the overall plastic damage range increases, the damage form area increases, and the damage degree deepens. The vertical displacement of the composite hard roof increases rapidly, and the presplitting effect is remarkable. (3) The evolution characteristics of roof principal stress transfer show that under the dual effects of mining and presplitting, the roof tensile stress area above the goaf is large, the rock failure horizon rises, and the roof failure height is high and the failure degree is deep. The stress concentration degree of the coal mass in front of the goaf is reduced, and the stress concentration range is transferred to the rock mass in front. With the advance of mining, the hard roof in front can break and caving in time, so as to avoid rock burst disaster caused by large suspended roof area. The field ground pressure monitoring shows that the average periodic weighting interval, weighting range, peak value before weighting, and peak value during weighting of the working face after presplitting decrease by 53.5%, 38.03%, 8.63%, and 5.96%, respectively, which effectively reduces the weighting intensity and ensures the safe and efficient mining of the working face.

May 16, 2023

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Refractory gold ore contains sulfide minerals like pyrite, chalcopyrite and sphalerite that are difficult to be directly leached by cyanidation or by lixiviants such as thiourea and halides. In such cases, it is necessary to perform oxidative pretreatment of the ore to oxidize the sulfide matrix, and gold particles can be exposed to the solution during the leaching process [1]. In recent years, hypochlorite and chloride solutions have been introduced as alternative materials for hydrometallurgical methods of gold extraction instead of cyanide solution [2]. A previous study by Hasab et al. [3] reported that the gold dissolution rate in hypochlorite solution was higher than in the cyanidation process, due to the presence of hypochlorous acid (HOCl) as a strong oxidizing agent. In a hypochlorite leaching system, the change in pH can influence the presence of oxidant species in the solution: the hypochlorite ion (OCl−) is stable in pH greater than 7.5, HOCl can be found in pH between 4.0 and 7.5, and aqueous chlorine (Cl2 (aq)) is the predominant oxidant when pH is below 4.0. As HOCl is the most effective oxidizing agent for gold extraction, pH should be maintained in the range of HOCl stability [4].

By Raymond A. Bradbury

Martin County Coal Corporation's operations are located on Wolf Creek in Martin County in the eastern part of Kentucky. The mining complex was started in 1971 and has grown to a 2.273 Mt/a steam coal operation. All of the production goes to Duke Power Company's Belews Creek electric generating station in North Carolina. Production comes from four seams that are mined by deep and surface mining methods. Surface mining accounts for 55% of the production and the remainder comes from 2 underground mines. Continuous miners are used exclusively underground. The preparation plant was originally designed to take coal at the rate of 907 Mt/h but that has gradually been increased to 1134 Mt/h. Other cleaning equipment includes Daniels DMS vessels, Model 77 Deister tables, 355.4-mm R. & S. Hydro- cyclones, Krebs 254-m classifying cyclones, Daniels froth cells and in 1980, 3 Krebs 508-mm heavy media cyclones were added to recover some lost and misplaced material. CMI centrifugaldryers and a Hey1 & Patterson size 100 thermal dryer are also part of the coal preparation equipment.

Jan 1, 1981

By T. J. Lutz, D. S. Yantek, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

Federal regulations require the installation of refuge alternatives in underground coal mines. Of the inuse refuge alternatives, more than 95 percent are mobile refuge alternatives, with the remainder being built-in-place (BIP) refuge alternatives. Heat/humidity buildup has been one of the major concerns with mobile refuge alternatives. For BIP refuge alternatives, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP refuge alternatives, the U.S. National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP refuge alternative with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP refuge alternative. The results show that the air supplied to a BIP refuge alternative may require heating or cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 21 °C (70 °F) and a relative humidity of 90 percent, providing 13 °C (55 °F) dew point air at 775 scfm, which is slightly higher than the mandated flow rate of 12.5 scfm per person, kept the internal apparent temperature below the mandated 35 °C (95 °F). Results for each test case are presented.

Jan 1, 2018

By Jacob L. Brinkman, Catherine E. Johnson

Unmanned aerial vehicles (UAVs) are being explored by researchers to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect concentration. A UAV fitted with gas sensors was attached to a stand in a controlled environment containing a mixture of NOx. The gas sensor measuring points were placed at various distances on and from the UAV body to evaluate downwash effects on gas concentration. Results show that the presence of downwash turbulence causes no statistically significant changes to concentration measurements at any distance or direction from the UAV. Based on these results, it is possible to use a UAV-mounted gas monitor to measure concentrations without concern for downwash interference, provided the UAV and measuring point are entirely contained within the gas cloud.

May 20, 2021

By J. Gibson

"INTRODUCTION As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action towards decreasing GHG and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery powered A/C systems and diesel-fired heaters, going no-idle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, stand-alone mobile equipment HVAC. THE HISTORY OF GHGS AND CLIMATE CHANGE In 1896 Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960’s Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Figure 1). In 1988 the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgement of a rising global annual temperature. The IPCC consists of over 2500 scientific and technical experts from more than 60 countries, and because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998 requiring all participating countries to reduce their GHG emissions by at least 5% from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States)."

Jan 1, 2015

By M. G. Hester

The ore reserve modeling of stratiform uranium deposits to be mined by selective underground mining methods must be done with consideration of the erratic nature of the ore forming processes that produced the mineralization. Estimation methods that model the uranium grade as a smooth transition between high grade and low grade drillhole intercepts tend to greatly overestimate the ore tonnage. Care must be taken to first establish realistic ore pod geometries and then estimate the grade of the reserve units within the pods.

Jan 1, 1985