Search Documents

By Greg Sanders, Bill Lueck, Michael Gilbert, Mahmood Khwaja

"The city of Minneapolis contracted with CDM Smith to update and provide a conceptual design for improvements to mitigate surcharge flooding in the Central City Storm Water Tunnel System (CCSTS). As a part of the project, CDM Smith conducted a field survey and condition assessment of the existing tunnel system. Information from the survey was then used to update the existing XPSWMM model and develop system wide alternatives.The CCSTS provides storm-water runoff drainage for nearly the entire area of the city’s downtown commercial district. The system consists of deep storm-water tunnels constructed in the St. Peter Sandstone, approximately 21 m (70 ft) below the street’s surface. The primary tunnels comprising the Central City storm water tunnel system are located below Hennepin Avenue, Nicollet Mall, Lesalle Avenue, Marquette Avenue South, 2nd Avenue South, South 5th Street, Washington Avenue South, Portland Avenue South, 2nd Street South, and Chicago Avenue South, as shown in Fig. 1. This network of tunnels conveys the runoff from a 305-acre tributary area that is generally bound by Hennepin Avenue and 1st Avenue North to the east, 12th Street to the south, 4th Avenue South and 7th Avenue South to the west, and 2nd Street South. These tunnels were constructed between 1936 and 1940, except for the Marquette Avenue South tunnel, which was constructed between 1963 and 1964.The CCSTS operates as a gravity flow system. These tunnels were constructed within the St. Peter Sandstone layer of bedrock and emerge from the bedrock at the Mississippi River below St. Anthony Falls. The Central City and the adjacent Chicago Avenue tunnel system converge into a single outfall at the Mississippi River. The runoff discharges from the converged outfall to a side channel of the Mississippi River, called a tailrace, located near the Guthrie Theater. The Minneapolis Division of Surface Water and Sewers provided 32 historic plats detailing the plan and profile of the tunnel system.The tunnel plans show nine different cross-section configurations. Eight configurations within the overall system generally show the same geometric “cathedral” shape with the inside dimensions varying from 1.2 to 1.8 m (4 to 6 ft) in width and 1.8 to 2.4 m (6 to 8 ft) in height. For analysis, these eight configurations were reduced to three configurations with regards to tunnel liner, cross-sectional area and support. For simplicity, the three configurations are described according to the three types of tunnel support used during construction: none required, light timber and heavy timber"

Jun 1, 2019

By Koehler Stout

Stopewall or room closure can be a problem in nining operations. In some mines, wall closure causes ore passes and nanways to collapse when they are enclosed in nine fill. When this phe- nomena occurs, heavy ground and, or, rock bursts frequently happen. Often, ground problems become progressively worse as mining in the stope block progresses toward the upper level. The sill and pillars in the level above may experi ence heavy ground and bursts. Sometimes the conditions get so bad in the stope that it is unsafe to mine the ore, so the stope is abandoned and the ore is lost.

Jan 1, 1980

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluated the effect of bucket orientation and operating parameters on resistive forces and penetration for rubber tire loaders. The work used a 1:16 scale LHD model to test a rubber tire loader (RTL) bucket operating at different levels of tractive effort, speed, digging height, and rake angles in a full factorial design experiment. The work repeated the test on two different muck piles with different particle sizes and used generalized regression modeling to test the association of rake angle, tractive effort, speed, and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort, and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle, and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The observation that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces is a novel contribution that enhances our understanding of RTL loading. The results also show that the effect of speed, tractive effort, and height above the floor all change with changes in particle sizes. This work adds to the literature on the effect of rake angle, height above the floor, tractive effort, and speed on penetration and resistive forces for rubber tire loaders.

Aug 24, 2020

By Basilio Giurgola, Jeremiah M. Jezerski, Filippo Azzara, Federico Bonaiuti, Russell H. Lutch

The Northeast Boundary Tunnel Project consists of a 23 ft diameter, 27,000 ft long, CSO tunnel, multiple underground connections, and significant surface works within an urban corridor. The NEBT alignment depths range from 60 to 140 ft and includes seven shafts ranging in depth from 77 to 155 ft with diameters varying from about 19.5 to 56 ft, some as in-line connections and others required adits for connection to the main tunnel. This paper focuses on the design and construction of two major underground connections which are the First Street Connector Tunnel and the Mount Olivet Road Diversion Sewer.

Jun 13, 2023

By David J. Brown

Extensive deposits of bituminous, subbituminous, and lignite coals occur in the western United States (Figure 1). Over one trillion tons of identified resources have been located and inferred by geologists and more than 200 million tons of western coal are mined annually (1). In the future, production of western coals will increase significantly and approach national production levels of higher-rank eastern coals. Western coals will be utilized in new power plants as a replacement fuel for oil and gas and may be used in advanced technologies such as diesel engines or in direct-fired turbines. Since these applications require low-ash, low-sulfur coals, crushing to fine sizes and significant cleaning to remove minerals and sulfur will be required. Coal cleaning traditionally has been associated with reducing pyrite and other mineral matter from high-rank eastern coals. To date, insignificant quantities of western coals have been cleaned before utilization and limited data on their washability characteristics exist. Because of this lack of data, it is difficult to predict how these coals will react to standard washing techniques.

Jan 1, 1985

By Thomas M. Larimer

Prior to April, 1961, the coal charge to Clairtonts coke oven batteries was 3" x 0" mine waslied coal having approximately 6.0% to 7.0% moisture. Even at this size and moisture content, the arching, rat-holing and hang-up was excessive and the effective live storage of coal was only 60% to 70% of the rated capacity of the coal bunkers, depending upon the moisture of the coal. In addition, many production delays were encountered in the time and methods required to fill the larry cars. The need for an improved metallurgical coke led to the introduction of pulverized coal to a portion of the plant in 196 1. When the full potential of the pulverizing equipment was realized, we were able to serve seven batteries in our second unit of batteries with pulverized coal through two coal bunkers. The discharge hoppers of these bunkers were equipped with air vibrators to assist the flow of pulverized coal into the larry cars. The vibrators were helpful in this respect but required considerable maintenance and caused damage to the bin plates.

Jan 1, 1968

From some of the largest tunnel projects in the some of the most vibrant cities, to smaller projects in remote corners of the globe, the Robbins Co. announced two tunneling projects in which its tunnel boring machines will be used. Robbins earth pressure balance (EPB) machines undercut Downtown Zhengzhou. Zhengzhou, a city of 7 million people, is set to become a crossroads for rail commerce in China. The country?s future main routes, traveling between Beijing and Guangzhou (North-South), and between Xuzhou and Lanzhou (East-West), will intersect in the city. The plan includes up to four rail lines in Zhengzhou itself, which will eventually link up to the national lines. Excavation of Zhengzhou Metro?s new Line 1 tunnels began on Sept. 28, 2010, when the first of two 6.3-m (20.7-ft) diameter Robbins earth pressure balance (EPB) machines was launched from a 16-m- (52-ft-) deep shaft.

Jan 1, 2010

By H. Kellerwessel

This paper refers to the new crushing and grinding process, which was invented by Professor Schönert (Ref.1), Clausthal, Germy (author of one of the papers presented at this meeting). The process is known as high pressure particle bed comminution or interparticle crushing. Several papers by Professor Schonert and his coworkers and by specialists of the companies producing the necessary equipment under license agreements already described fundamentals of the process, the equipment used, results of lab size and large scale tests and finally the first results of truly commercial operations (Ref .2 to 11). Therefore it should be sufficient to summarize the main facts here: - To a bed of bulk material a pressure of more than 50 MPa is applied. Comminution is achieved mainly by the pressure which one particle transfers to the other and not by squeezing single particles between the working surfaces of some crusher or grinding media.

Jan 1, 1987

By M. Werner

Mining in the Coeur d'Alene Mining District has been going on for over 100 years with a long- term continuation very likely. Mining is presently carried out at depths below the -5000' horizon. As mining continues at ever increasing depths, higher in-situ rock stresses and subsequent rock deformation is encountered making mining costly and hazardous. To provide access for men and materials in such areas, a wooden raise preparation structure is typically built. Although these structures provide adequate support and access, they have proved to be very costly to construct and maintain.

Jan 1, 1986

By William L. Young

I think I should let you in on one of Canada's best-kept secrets, if you will promise not to tell it all over the place. Believe it or not, good, honest, enterprising capitalism is still alive and flourishing north of our common border, and I am living proof that capitalism is still working for the little guy. My personal story of mining development in Canada isn't all that rare -- you've probably heard something like it from other areas and other days several times -- but my case brings it up-to-date. I would like to Tell you briefly the history of Northumberland Mines Limited, a contemporary case of individual enterprise getting a mining operation underway. And if I can do it you probably can too.

Jan 1, 1981

By Patricia Pride, Mike Robison, Jon Bergenthal, Wojciech Klecan

"The Lower and Middle River Des Peres (LMRDP) CSO Storage Tunnel is the largest single component of Metropolitan St. Louis Sewer District’s (MSD) CSO control system improvements planned to meet consent decree requirements for MSD’s Lemay Service Area. The 13.7-km (8.5-mile) long, deep, hard rock tunnel will have a finished diameter of 9.1 m (30 ft). Beginning at the Lemay Wastewater Treatment Plant (WWTP), the alignment follows the channelized River Des Peres to the outfall of the existing Forest Park tubes, as indicated in Fig. 1.The project includes three construction shafts, 34 intakes and a deep, cavern-style pump station located adjacent to the WWTP. The tunnel will be driven from the Defense Mapping shaft to the Macklind shaft. Another shaft is located near the midpoint at the tunnel in River Des Peres Park.The Forest Park intake, located at the upstream end of the tunnel just beyond the Macklind shaft, is a large, tangential vortex intake structure. With a peak flow rate of 170 m3/s (6,000 cfs), it will have a 6.1-m (20-ft) diameter dropshaft to transfer flow into the tunnel.The project includes another three large tangential vortex-flow intake structures with peak flow rates ranging from 28 to 44.5 m3/s (990 to 1,570 cfs). These large intakes are located at points where three large sewers (formerly creeks) enter the River Des Peres. Dropshaft diameters for these intakes range from 3 to 3.7 m (10 to 12 ft) in diameter. The 30 remaining intakes are smaller tangential vortex-style, with dropshafts in the range of 0.8 to 1.7 m (30 to 66 in.) in diameter.Each intake structure drops flow into a deaeration chamber constructed adjacent to the tunnel at tunnel depth. Intake tunnels transfer flow from the deaeration chambers to the main tunnel. Most of the intake tunnels are short. However, two are long. The Glaise Creek tunnel will extend 762 m (2,500 ft) from the main tunnel to the Alaska Park intake, while the Rock Creek tunnel will extend 823 m (2,700 ft) from the main tunnel to the Rock Creek intake. The dewatering pump station, located at the downstream end of the tunnel, will be built inside a large, horseshoe-shaped cavern with two access shafts. Excavation of the cavern and its access shafts will be performed by the tunnel contractor. Build-out of the dewatering pump station will be performed under separate contract."

Jun 1, 2019

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By Yi Luo, Jian Yang, YUJIA LIAN

Scale physical models, constructed according to the principle of similarity theory, have been widely used to simulate the mining disturbances to surrounding strata and to evaluate the effectiveness of implemented ground control techniques. This technique has also been used for studying mining-induced surface and subsurface subsidence. The movements of the observation points installed on the physical model at different mining stages are currently measured using total station which is time-consuming and inaccurate especially on small scale models. A photogrammetry-based measurement system has been developed. During a physical modeling process, photos of the model can be taken during the simulation process reducing survey time from hours to a few seconds. A program, Photogrammetry Analysis for Physical Modeling of Mine Subsidence Process (PAPMMSP), developed based on photogrammetric principle is used to quickly identify the installed observation points and accurately determine their coordinates. The measurement accuracy is well under submillimeter level—an ultra-important advantage as any measurement errors in coordinates are magnified by the model dimension scale (commonly 20 to 400). A physical modeling case of subsurface strata movements and deformations associated with longwall mining operations is presented in the paper to demonstrate the functions and capabilities of the developed photogrammetry program.

Aug 11, 2020

By Leonard Sugin

As we approach the end-of the 20th century we are made more aware of the tremendous role that energy plays both directly and indirectly in our varied way of life. The industralized nations of the world have already established industries and economies which are greatly dependent upon the availability of energy. The underdeveloped and developing nations of the world are slowly and surely moving to the same utlimate requirements. The world wide need for distribution of energy sources is continuing to grow. At the present time there is a great imbalance between the sources of energy and the consuming economies In order to bring about greater equality between supply and demand major efforts and large capital expenditures are constantly being made. Industralized areas are seeking their own independent sources of energy whereas those areas of the world which contain great reserves of energy are limiting its export as well as developing its own industralized capacity. Nevertheless, energy bearing materials are still transported great distances in order to satiate the appetites of power hungry economies.

Jan 1, 1975

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"One of the most pervasive diseases in the mining industry is noise-induced hearing loss. The exposure of miners to noise levels above the permissible exposure level results in hearing loss in approximately 80% of coal miners by retirement age. In this context, the U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for longwall mining systems, which are used to extract half of the national underground coal production.From field measurements, previous research determined that the dominant sound-radiating components at the shearer of a longwall system are the two cutting drums used to remove coal. Due to the dimensions and complexity of longwall mining systems, the NIOSH project developed a validated finite element model of the cutting drum to use in predicting the sound radiated by the drum due to the excitation forces experienced in underground operations. This same model will be used to develop engineering noise controls for the drum. The excitation forces arise from the interaction of the cutting bits and the coal and are transmitted to the cutting drum through the bit holders. Due to the adverse conditions at the face, and a lack of instrumentation approved for underground use, the operational coal cutting forces have not been assessed before. To this end, NIOSH, in collaboration with Michigan Technological University, developed a self-contained, intrinsically safe instrumented bit to measure these forces.This paper describes the development of the instrumented bit and the measuring of operational coal cutting forces at three working coal mines. The measurements revealed that the forces have a flat spectrum, representative of the impact nature of these forces, up to around 100 Hz. Above this cutoff frequency, the force magnitude decreases at a rate proportional to the inverse of frequency squared."

Jan 1, 2014

By D. L. McCain

In considering slurry transportation for Consolidation Coal Company's Loveridge Mine in Northern West Virginia, many things were taken into account. The advantages of slurry transportation in comparison to shuttle car, belt and rail transport have been given in previous publications." These include increased safety and the potential for increased productivity. In addition to these considerations, the slurry transport system installed in an existing mine provides an alternate or additional transportation mode to the one already existing. In the Loveridge Mine, this is rail haulage. Since the rail system is a single track system and the distances involved are several kilometers, it is not always possible to provide for haulage of loaded cars, return of empties, supplies and maintenance in an efficient manner. Slurry transport of the coal from the production faces to the preparation plant allows the rail system to fulfill the remaining transportation needs in an efficient manner. Consol initiated development work in slurry transportation in the early fifties leading to the construction and operation of the 174-km (108-mile) Cadiz-to-Cleveland pipeline which carried 1,200,000 metric t/y (1,300,000 t/y) from 1957 to 1963. Development work on coarse coal slurry transportation for underground mines started in 1970 with feasibility tests on coarse coal at Conoco's Ponca City, Oklahoma, slurry test facility. A series of tests were conducted in several locations as development work proceeded on the various subsystems, mechanical equipment and controls required to produce a working system to follow a continuous miner in a room-and-pillar type mine, then to combine the coal production from several mine faces for mainline transportation to the preparation plant. The face system, including the crusher-pump vehicle, hose hauler vehicle, slurry booster pump units, return water unit and 900 to 1,200 m (3,000 to 4,000 feet) of pipeline was brought together for the first time and tested as a system at Consol's Robinson Run Mine in northern West Virginia in 1975. A pipeline wear test at the Loveridge Mine where 300,000 tonnes (330,000 tons) of minus 127-mm (5-inch) run-of-mine coal were pumped from the raw coal bin into the preparation plant and a large scale test in Ponca City on a multiple feed sump where several slurry flows could be combined to provide surge capacity and a constant reclaim rate for mainline transportation completed the preliminary testing for a complete system. A decision was made to commit the system to a mine, and the south half of the Loveridge Mine was chosen. This site required the transporting of coal from one longwall and two continuous miner development faces. To prevent startup and unexpected problems in the slurry system from shutting down production of coal from the longwall face, the rail car loading point from the main section belt was chosen as the feed point for the slurry system and the design would allow for rapidly switching from one transport mode to the other. Scheduling of required development entry work and the developmental nature of the system led to a decision to install only one continuous miner face slurry transport system rather than two for this first system. The type of continuous miner in use at the mine for the foreseeable future was the Joy 2BT6 twin boring machine. This machine cuts a stable, arch-shaped entry and was therefore allowed to mine about 26 m (85 feet) of entry before roof bolting was re¬quired. Since peak production from this type of machine was not high, a smaller transport system could be used with it.

Jan 1, 1981

By F. G. Miller

Over the past 30 years, the coal industry has been continually striving to perfect methods for cleaning fine coal to acceptable ash and sulfur contents while maintaining maximum product yield. The flotation process has been part of this effort and its importance is expected to grow as new utilization technology demands finer and purer coal products. The work outlined in this paper is part of a larger effort aimed at development of new and improved flotation systems for removing sulfur and ash from as-mined coal as well as for producing super-clean coal for future markets. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of flotation.

Jan 1, 1986

By Paul T. Allsman

The guiding principle in developing this plan resulted from evaluating potential future markets for oil, the quantity of mineable oil shale and the optimum rate of production comensurate with market demand on the available oil from shale. In addition, the rate of production may depend upon a solution to the problems of scarcity of resources other than oil shale. The rate of production finally will tend to establish the choice of technologies with these limits. The principle components discussed will be: 1) The place of oil shale among the various energy sources and its relative adaptability for use in the area of major consumptive demand. 2) A recalculation of the reserves and their classification on the basis of quantity, grade - gallons per ton, - and physical characteristics principally thickness, overburden and depth.

Jan 1, 1982

By KOKOWSKI J., RUDZIŃSKI Ł.

The LUMINEOS network was established in 2013 to monitor mining-induced seismicity in Legnica-Głogów Copper District (LGCD), located in south-western Poland. Since the starting time, the network was improved and today consists of 17 seismometers and 10 accelerometers. Up to now, the strongest recorded earthquake in the region had Mw4.0. Both raw seismic data and earthquakes catalog for events recorded by the LUMINEOS network are fully open and available on the EPISODES platform (https://tcs.ah-epos.eu/#episode:LGCD). During the last 7 years, the network improvements gave us a possibility to increase location accuracy for shallow mining events. This accuracy is influenced by factors such as the configuration of seismic stations, noise level at seismic stations, and the influence of the velocity model. Here we encountered two main issues which are worth to discuss. The first one is the low detection threshold of two seismic stations and their significant impact on the location errors. The second one is the large uncertainty in the S-wave picking. Even though S-waves are not so clearly visible on seismograms, they are very helpful in the estimation of source location and strength of seismic events in the region. In our work, we present the history of LUMINEOS network and corresponding improvement on location accuracy as well as the influence of noisy stations on the error distribution and how it is connected with location results. We also investigate the effect of the S-wave phases and how they are related to the accuracy of the earthquakes locations in the network.

Apr 26, 2022

By R. D. Doepker

The dissolution of metals from various metal-mine tailings has been studied through a series of submerged tailings batch tests at U.S. Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97 pct saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79 pct or 70 pct saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained nearly constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1990