Search Documents

By J. Dasher

Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to al low editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels.

Jan 1, 1991

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

The segregation process has been known for many years and applied industrially for the treatment of various refractory copper ores. The principles of the process are briefly reviewed; the process was tested in the laboratory on two copper-cobalt oxide ores from Gecamines, Shaba Province, Zaire. Various parameters of the process, such as segregation temperature, dosage of reducing and chloridizing agents and flotation conditions were inyestigated. Experimental results have shown that the segregation of copper could proceed satisfactorily at low temperature (1000° K) but that of cobalt required higher temperature and higher additions of reducing and chloridizing agents.

Jan 1, 1992

By William Bergeson

This paper presents the challenges of the Homestead Avenue Interceptor Extension (HAIE) project in downtown Hartford, Connecticut. The new 72-inch (1,830 mm) sewer pipeline project consists of installing approximately 3,010 linear feet (920 m) of PVC lined reinforced concrete pipe using pressurized face microtunneling. The entire alignment is located within soft to very soft, varved silt and clay. To the extent possible, the alignment was selected to avoid bedrock, glacial till, miscellaneous fill,buried steel piles, and utilities. Challenges for this project include low ground cover, crossing major transportation routes, and limiting settlement to prevent damage to historical buildings and critical utilities. The machine was selected for the ground conditions. Design calculations were performed for selecting the reinforced concrete pipe class and for evaluating settlement. The potential for settlement damage was evaluated using both conventional analysis and finite element analysis

By H. Huang, R. N. Gow

"EH-pH diagrams are useful tools in understanding how mineral surfaces react in solution and particularly how aqueous conditions can be changed to enhance mineral leaching processes. Successful application of these diagrams, however, requires that several considerations be kept in mind to prevent what had been termed as “gross errors” in their calculation and use. In this paper, the aqueous Cu-S system is used as the basis for explaining the mass-balanced method of calculating EH-pH diagrams with the STABCAL thermodynamic equilibrium software. A breakdown of the Gibbs’ Phase Rule and how it is used in STABCAL to modify the diagrams is included. The methodology was applied to the aqueous Cu-As-S system, and resulting diagrams were compared against examples of those generated using the predominant-ion method. The complexity of such diagrams increases with every additional component, and competition between species becomes more apparent, as can be seen by curvature in the resulting mass-balanced diagrams. The complete diagram for enargite (Cu3AsS4) is shown. It compares well with spectroelectrochemical measurements from Raman spectroscopy and cyclic voltammetry studies.IntroductionInnovation in the field of processing arsenicbearing copper ores has been of particular interest. Copper arsenic sulfosalt minerals such as enargite (Cu3AsS4) and tennanite (Cu12As4S13) are now frequently prevalent in ore bodies as the oxide and easily leachable sulfides become harder to find. These minerals, unless pretreated somehow, concentrate in copper sulfide flotation processes, in turn concentrating the arsenic levels. Increasing environmental restrictions on arsenic content for smelters makes the hydrometallurgical processing of these concentrates more favorable. While enargite is considered one of the more refractory copper sulfides, more so than chalcopyrite (CuFeS2), there are still several methods, both industrially proven and in development, that are capable of processing these ore types. Alkaline sulfide leaching can be used as a pretreatment method to solubilize arsenic selectively (Delfini et al., 2003; Anderson and Twidwell, 2008; Tongamp, Takasaki and Shibayama, 2010a, 2010b), or the entire metal content can be leached using acid-type leaches such as acidified ferric sulfate (Dutrizac, 1981; Hackl et al., 1995; Klauber, 2008), or the chloride assisted, CESL (McDonald and Muir, 2007) or nitrogen species catalyzed (Anderson, 2003) processes can be used.As development of these leaching technologies proceed, it is also important to develop an understanding of the mineral thermodynamics. To date, there are numerous studies on the Cu-Fe-S-H2O system, particularly as it relates to chalcopyrite leaching, yet few studies have done on the Cu-As-S-H2O system. Computer-generated EH-pH diagrams have been employed to illustrate the importance of thermodynamic calculations in providing insight into such a system."

Jan 1, 2016

By Leena Suopajärvi, Karin Käär, Marcin Szumny, Jari Joutsenvaara, Md Ariful Islam, Helmut Mischo, Georg Meissner, Ossi Kotavaara, Catalina Vrabie

This study outlines implemented tactics and results for community empowerment through participation in questionnaire surveys, educational programs, and discussion on sustainable sourcing from new critical raw materials (CRMs) projects. Utilising questionnaire surveys, including the Public Participation Geographic Information System (PPGIS), the research gathered public opinions from Estonia, Germany, Poland, and Zambia, receiving 1,068 responses. These responses addressed various social, economic, and environmental issues related to CRM projects. Feedback from educational courses with participants from over 25 nations and public events provided additional insights. The collected data and feedback offer crucial input for advancing sustainable and responsible CRM sourcing strategies in these regions.

Feb 1, 2025

By K. Heatwole, D. Shier, A. Davis, J. Kidder, S. Sunkavalli

"Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios, including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation.IntroductionAcid rock drainage (ARD) is a notable environmental concern in areas where rock or other material with acid generation potential is disturbed. ARD is defined as drainage that occurs as a result of sulfide oxidation in rock exposed to air and water. ARD is characterized by low pH, elevated metals concentration (especially aluminum, iron and manganese), sulfate and high total dissolved solids. The low-pH water that results from acid generation is capable of solubilizing heavy metals contained within the rock. The principal sulfide mineral in mine wastes is pyrite (FeS2). Pyrite oxidation is complex and can involve chemical and biological reactions. Oxidation of pyrite by atmospheric oxygen produces one mole of Fe2+, two moles of SO4 2- and two moles of H+ for every mole of pyrite oxidized, as described by Eq. (1)."

Jan 1, 2015

By D. E. Munson

The Waste Isolation Pilot Plant (WIPP) Project was established in 1975 by the Department of Energy (DOE) under Public Law 193 to develop the necessary technology for safe disposal of radioactive wastes from the defense programs of the U.S. The technology development involves extensive theoretical, numerical, and laboratory programs, as well as construction of the WIPP facility in southeastern New Mexico for in situ testing and waste storage demonstration. If after the demonstration, the facility is found to comply with regulations of the Environmental Protection Agency, then the facility will become a repository for Transuranic (TRU) waste. The underground portion of the facility is 655 m beneath the ground surface in massive natural salt deposits of the Salado formation, as shown in Figure 1.

Jan 1, 1991

By C. F. Giermak

Over a considerable period of time great interest has been shown in selective dry concentration of fine ferromagnetic particles, although it is only recently that new permanent magnetic materials have been made available to permit building of such permanent magnetic separators. It is well known that the conventional drum separator does' not efficiently separate fine materials. The centrifugal force on any drum acts in accordance with the particle size and gravity, which may beat varying magnitude-.opposite to the magnetic force, especially when the material is not closely sized. The Magnetic-Mechanical Separator (MMS) is designed for the concentration of fine, unsized magnetic materials where the percentage composition of magnetics to nonmagnetics, or the nature and texture of the materials, is such that its unique agitation and shake-out action with no centrifugal force provides greater efficiency than is obtainable by conventional magnetic separation equipment. This machine consists of a complete double belt conveyor unit with a premagnetizing Axial Pole Agitating Pulley at the feeding end of the lower conveyor belt and a special agitating concentrator magnet above the lower belt of the upper conveyor.

Jan 1, 1965

By Allan G. Provost

Shaft construction is assuming ever increasing importance when new mining enterprises are considered. The reasons for this increased emphasis is the much greater depths at which many new ore-bodies are being developed and the rapid depletion of near surface reserves requiring mines to go to greater depths on existing deposits. These greater depths increase the probability of exposure to unfavorable geologic conditions and it is more likely that high ground and/or water pressures will be experienced at these depths. The large capital costs involved and the critical position of a shaft in the overall mining program necessitate that this element of project development be given careful and critical consideration. The Henderson No. 2 Shaft is located in the Rocky Mountains of north central Colorado (See Figure I), about 55 miles west of Denver, near the community of Empire in Clear Creek County. At the 10, 442 foot collar elevation, winter arrives in late September and brings snow to contend with until May. The labor force for Shaft No. 2 is approximately 90 men. They are provided access to the project via all-weather U. S. Highway 40. SHAFT DESIGN The Henderson No. 2 Shaft is a 28-foot I. D. circular, concrete lined (1 foot thick) vertical shaft. The final depth will be approximately 3100 feet

Jan 1, 1972

By Robert P. King

In April, 1975 the Colorado School of Mines began monitoring rock mass response associated with a long- wall shield demonstration project near Raton, New Mexico. This project was sponsored by the U. S. Bureau of Mines (DOE) and performed at Kaiser Steel Corporation's York Canyon Mine. Two of the results of the intensive instrumentation effort are the empirical subsidence and horizontal strain models presented herein. These models are based on data gathered during mining three adjacent longwall panels (4N, 5N and 6N). A total of 251 permanent surveying monuments were monitored over the three-panel area. Lines of monuments were oriented along panel centerlines, perpendicular to centerlines and diagonal (45O) to centerlines. Active monuments were monitored twice a week, with less frequent monitoring of stable or slow moving monuments. Primary subsidence monitoring equipment consisted of an AGA Geometer Model 75 and a Wild T-2 Theodolite with -a Wild-Sercel DI-3S distomat.

Jan 1, 1979

By Drew Bazil, David Smith, Matteo Ferrucci, David Pittman

The Gateway program will provide additional rail capacity between New Jersey and Manhattan. This paper describes how a 70-foot-deep section of cut and cover tunnel was designed to directly support future high-rise towers. The tunnel will link previously completed tunnel sections under Hudson Yards to future tunnels under the Hudson River. The design aims to minimize constraints on future overbuild and future tunnels, while maximizing constructability within a small worksite. The tunnel will pass under the High Line elevated walkway, next to an active rail yard, and close to a subway tunnel. The design was developed by a tri-venture of WSP, STV and AECOM. WSP led the design of major underground works; STV designed utility relocations and the underpinning concept for the High Line; and AECOM designed temporary in-tunnel systems. Construction is expected to start in 2023.

Jun 13, 2023

By B. Simser, T. Butler

Glencore’s Nickel Rim South Mine, located in Sudbury, Ontario, Canada, is a primary/secondary blasthole operation with ore zones lying between 1,100 and 1,700 m below surface. One of the main benefits of the primary/secondary mining method in high stress ground is that up to 50% of the mining will take place in secondary stopes that should be in a yielded rock mass state. Every future secondary mining stope begins as a primary stope abutment pillar. As with many mines, the stress loading history and rock mass conditions can vary considerably in space and time. Safe mining practices cannot allow for an assumption that the planned secondary stopes are indeed yielded. An incorrect assumption can result in mining development and stoping taking place in high stress ground rather than the expected yielded rock mass conditions. This can result in higher levels of seismicity than expected and incorrect ground support recommendations in areas where workers could be exposed. Seismic monitoring is the mines’ premier tool to track the actual rock mass response to mining. Yielded zones have a reasonably clear seismic signature/pattern over time that is visible in the collected data. The ability to accurately locate small magnitude seismic events can help define and delineate different stages of rock mass failure. The vast majority of the seismic data recorded by the microseismic monitoring system is below moment magnitude (Mw) 0.0. Examples are provided showing how small seismic events (Mw < -1.5) can help provide feedback from the rock mass deformation that allows the ground control engineer to gain a better understanding of how the rock mass is responding to mining processes.

Apr 26, 2022

By S. L. Barua

An industrial engineering and computer simulation study was conducted on reclamation operations to evaluate the possibility of integrating mining and reclamation operations, and to evaluate the factors which influence the production potential of scrapers. The study was done in a southern Illinois strip coal mine producing approximately 2.27 M metric tons (2.5 million short tons) of clean coal annually. The main outcomes of this study are (a) it is possible to reduce reclamation cost about 20-25 percent by integrating reclamation and mining operations, (b) haul distance has the most significant effect on scraper production, (c) push-pull is the best mode of operation for wheel scrapers for topsoil/subsoil removal, and (d) historical data obtained from the mine for one year show that average dozer productivity in rock grading is about 60 percent lower than the expected production; similar data for scraper is about 25 percent less.

Jan 1, 1981

By L. A. Romo, J. A. Ferrer

INTRODUCTION The principle line of the Caracas Metro is located generally along the most important east-west traffic corridor of the city from the yards and shops in Propatria at the western extremity to Petare, and eventually beyond to Palo Verde at the eastern end, a route distance of 21 kilometers. There will be 23 stations along the alignment, underground, at grade and elevated, and the line is forecast to handle 1,209,100 passengers daily by the year 2000 with a travel time of 29 minutes between Propatria and Petare. This principle line was divided into three sections for design purposes: Propatria-Fuerzas Armadas, Section I, Fuerzas Armadas-Chacaito, Section II and Chacaito-Petare, Section III. These sections were further subdivided into subsections for construction purposes. The Venezuelan Government, through its Caracas Metro Office in the Ministry of Public Works, awarded design contracts in sections to PARSONS BRINCKERHOFF-TUDOR-BECHTEL for Propatria-Fuerzas Armadas, Section I, OCOIDESA-GRID-APM for Fuerzas Armadas-Chacaito, Section II and OCOIDESA GRID-APM for Chacaito-Petare, Section III. Construction contracts were awarded by international bidding and work is now underway, by joint venture organizations of Venezuelan and foreign firms. The first two sections are under the administration of a company of Engineer/Inspectors in each section. The construction supervision of contracts in the first section is under the administration of the Venezuelan firm, Gómez-Celis-Herrera, (GCH) Engineers, acting under contract to the new C.A. Metro de Caracas that replaced &apos; the former Office of the Metro. The Propatria-Fuerzas Armadas section, approximately seven kilometers long, consists in part of the 2,951 linear meters of twin-bore

Jan 1, 1979

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By Homer E. Harris

As a result of the enactment of the Federal. Coal Mine Health and Safety Act of 1969 1, the Department of Health, Education, and Welfare (HEW) has been carrying out research in the "field of coal mine health". The National Institute (formerly Bureau) for Occupational Safety and Health (NIOSH) was designated the agency within HEW to be responsible for such research activities. One of the early programs sponsored by NIOSH was undertaken by Eastern Associated Coal Corp., with the Harvard University School of Public Health participating as a subcontractor to Eastern. This program on Coal Mine Respiratory Protective Devices, which started on June 30, 1970, had five major objectives as follows: a. to determine current status of respirator usage with respect to duration and frequency, types. and maintenance b. to determine acceptability ( and reasons therefor) of currently used units c. to determine protection factors provided by respirators worn by working miners d. to make recommendations on ways to improve existing units, or on research needed to develop new types of respiratory protective devices for coal miners e. to provide recommendations to mine management on more effective use of respiratory protective devices

Jan 1, 1973

By G. V. Henderson

Large reserves of high calcium limestone have been outlined in the Redwall formation at Nelson, Arizona. Geologic mapping, core drilling and shallow seismic refraction studies have outlined more than 100 million tons of high quality, chemical and metallurgical grade limestone in the Mooney Falls member of the Mississippian Redwall Limestone. Well developed Karst zones in the Redwall were delineated by field mapping, seismic profiling and core drilling. Development of large reserves of high quality, thick beds of limestone near the present mine and rail facilities was the basis for the current mine and plant expansion. When completed in 1978 the planned 1800 Tpd production will represent the largest lime operation in the Western United States.

Jan 1, 1978

By Neil D. Donnell, O&apos

Ore reserve estimation at the Syncrude Canada Ltd. open-pit oil sands mine in Northern Alberta has evolved since the project&apos;s inception. Early techniques followed a conventional petroleum reservoir analysis format, with relatively widely-spaced drill holes and semiquantitative grade data. Experience has developed a more standard mining approach, including classification of geological materials by both lithology and sedimentary origin, timely and multi-purpose drill holes, precise analytical data, empirical recovery factors, a computerized geological data base, and an ore body block model. Future efforts will involve enhancement of existing techniques, use of geostatistical algorithms, quantification of confidence limits, and improved control of the ore model by geological parameters.

Jan 1, 1985

By R. J. Miller

Rock strata, natural and mining-induced stresses, and structural features can combine to create dangerous instabilities in or around longwall panels. Rock noises and properties variations associated with local stress systems can be used to characterize developing instabilities. Through a learning process at a particular mine, guidelines can be developed to allow the determination of relative risk and timing of a potentially disastrous instability. Once a dangerous instability has been identified, operational modifications can be employed to get through the instability, or active measures such as destressing can be used to mitigate the instability. This paper will discuss how an integrated monitoring system and associated data processing can be used to develop a hazard prediction capability for a longwall mine.

Jan 1, 1996