Search Documents

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

By Jürgen Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world’s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards decarbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain, or Germany are only forerunners of this development—their centuries of coal production have been finished. The concept of sustainable development (SD) is fundamentally based on a model of progress where ecological, economic, and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as how can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry’s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia, and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later.

By William Gleason

From Nov. 16-20, the Extraction 2025 Conference will be presented in Phoenix, AZ. The unique conference brings together the 12th International Copper Conference, the 6th International Symposium on Nickel and Cobalt as well as cross-cutting symposia. Extraction 2025 is co-organized by The Metallurgy and Materials Society (MetSoc) of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM), the Society for Mining, Metallurgy & Exploration (SME) and The Minerals, Metals & Materials Society (TMS). The previous, and first Extraction meeting (Extraction 2018) was held jointly by these three societies seven years ago in Ottawa and was a huge success with more than 90 percent of respondents indicating interest in attending a future event. Kimberly Mills, senior process engineer at Samuel Engineering, is the lead for SME. “This installment of Extraction is featuring Copper 2025, Nickel-Cobalt 2025 as well as crosscutting symposia,” said Mills. “All three societies participate on the International Organizing Committee for the Copper Conference Series and are well situated to host this event together. TMS is also hosting the Ni-Co conference this year and agreed to include it as part of Extraction. There are many aspects that can be shared between these commodities to share information on processing technologies and to learn from each other.” SME is the overall conference chair and running the logistical aspects of the event, which includes managing all aspects of the venue and the registration system as well as tours and short courses, Mills said. “SME has many dedicated members serving in various capacities on organizing and programming committees, including Nick Gow serving as Technical Committee Co-Chair for Copper and Adam House assisting on the Copper IOC.” When Extraction 2025 kicks off, it will be focused on the metals needed for the global energy transition with a special focus on copper and nickel-cobalt. “With as rapidly as the industry is changing and the huge demands for these metals we have some serious challenges ahead of us,” Mills explained. “These challenges require collaboration, creative solutions and engaging experts, both inside and outside of our fields, with a push for sustainable sourcing, ethical supply chains, environmental and social responsibility.” The International Copper Conference was started in 1987 as a collaboration between the Institute of Mining Engineers of Chile (IIMCH) and MetSoc of the CIM. The event is typically held every four years and has always been held as a standalone or headlining event at a society annual meeting, said Mills. “Over the years, this conference series alone has brought together members of IIMCH, MetSoc, TMS, SME, the Society for Metallurgists and Miners from Germany (GDMB), the Mining and Materials Processing Institute of Japan (MMIJ), the South African Institute of Mining and Metallurgy (SAIMM) and the Nonferrous Metals Society of China (NFSOC),” she added. “Being a part of Extraction allows for even more sharing of ideas and expansion of networking. This conference has not been held in the United

Oct 1, 2025

By Todd Grounds, William R. Reed, VASU GANGRADE, Michael Shahan, Garron Ross, Kunal Singh

Roof bolter canopy air curtains (CACs) are gaining acceptance as a respirable dust control device that can provide roof bolter operators with protection from overexposure to respirable coal mine dust. Both lab and field studies on the effectiveness of roof bolter CACs have been published. Field studies have shown the effectiveness to be variable. However, in all previous field studies, none has been conducted when the roof bolting machine operates downwind of the continuous miner (CM)—a scenario for which the CAC was designed to provide respirable dust control. This study, performed by researchers from the National Institute for Occupational Safety and Health (NIOSH), was conducted to test a CAC on a roof bolter machine operating downwind of the CM. The results of testing demonstrated that the roof bolter CAC can effectively provide respirable dust protection for roof bolter operators with dust control efficiencies ranging from 11 to 40%.

Oct 14, 2020

By Justin Srednicki, Chenming Zhou

Ambient electromagnetic (EM) noise (natural or manmade) is a major limiting factor for the design and operation of many electronic devices, including through-the-earth (TTE) communications and tracking systems. Extensive studies on EM noise were conducted by the US Bureau of Mines in the 1970s and 1980s. Changes in the design and operation of electrical equipment since then, however, have resulted in changes in the EM noise environment. This paper reviews past research on surveying EM noise in the extremely low-frequency (ELF) and very-low-frequency (VLF) bands, which are the operating bands for TTE systems, and introduces a new battery-powered, rugged, portable measurement system for surveying EM noise in mining environments. Examples of surveyed EM noise measurement results in and above an active underground coal mine, using the new system, are presented in terms of absolute magnetic field strength levels. A new metric, average noise level (ANL), is introduced to characterize the noise level relative to a particular frequency band for a specific location. It is found that EM noise in mining environments varies significantly with time and location. EM noise levels at frequencies of 30 Hz that shifted from power harmonics (e.g., 90, 150, 210, 270 Hz) are relatively low and their variation with time can be statistically modeled by a Gaussian distribution. The conclusions and findings presented in this paper can help better design and operate TTE communications and tracking systems in underground mines.

Oct 14, 2022

By P. Knudsen, S. Rosenthal

INTRODUCTION In 2010, Montana Tech was gifted 65 acres of land immediately west of the campus. The parcel of land included an old silver mine called the Orphan Boy Mine. The Orphan Boy and its sister, Orphan Girl, were developed about1895 and operated until 1956. In addition to the gift of land, a significant industry gift was obtained to develop a first class training facility, which we call the Underground Mine Education Center (UMEC). The UMEC has been funded primarily by industry through donations of dollars, equipment, and supplies. The UMEC is a unique hands-on, educational environment for today’s students who are being trained to find, develop and process the worlds' natural resources. The center complements courses in mining engineering, geological engineering, environmental engineering, metallurgical engineering and occupational safety and health. It also serves as a as research facility utilized by students and faculty, and other organizations interested in doing research a hard rock underground mine. LOCATION The Orphan Boy and Orphan Girl Mine are located approximately 700 feet (ft.) apart and the Orphan Girl Mine is part of the World Museum of Mining. Underground they are connected on various levels and all levels below the 100 ft. level are currently flooded. The Orphan Boy mine was 804 ft. deep and Orphan Girl was 3200 ft. deep. The surface locations of the two mines and some of the underground workings on the 100 ft. level are shown on Figure 1 (2015). CONSTRUCTION Land ownership was gifted from BP/ARCO in 2010 and planning started immediately. In June of 2011, site development for the decline to the 100 ft. Level of the Orphan Boy began with a satisfactory portal site developed (Figure 2). We hoped to be able to start driving the decline in July. However, the portal was sited approximately 125 ft. away from a natural gas line that bisected the Montana Tech campus. While outside the right of way for the line, Northwestern Energy requested that no blasting be performed near the gas line until such time as the gas line was abandoned in the fall so decline development was put on hold. The gas line was officially abandoned in January of 2012.

Jan 1, 2019

By Manoj Khandelwal, Minghui Liu, Jian Zhou, Kun Du

The waste rock and tailings backfill into the mined-out areas are the most effective method for solving the environmental pollution and surface disasters for nonferrous metals mines. In practice, the success and availability of backfill operations are dependent on the slurry fluidity and the strength properties of cement backfill. The transport of the slurry through the pipeline to the designated backfilling area relies on its eximious flow properties, while the appropriate strength of the filling body ensures the safe operation of the stope. In this paper, the effects of cement and aggregate types on the slurry fluidity and strength characteristics of cemented backfill are studied in detail, which are often ignored in other pieces of literature. Diffusivity is used as an indicator to evaluate the slurry fluidity. Various slurries whose concentrations ranging from 70%, 73%, 75%, 78%, and 80% are made with different aggregate ratios and cement-sand ratios are tested. It has been shown that slurry fluidity is inversely related to its concentration, but 78% is the “stopping point” for the deterioration of fluidity. The addition of rod-milled sand improves or worsens the cemented backfill (CB) strength depending on the amount of rob-milled sand. The uniaxial compression experiment results on 216 CB specimens produced by different combinations of influencing variables showed that CB specimens made from cement with superior mechanical properties have a higher uniaxial compressive strength (σucs). It has been also found that the effect of aggregate ratio on the CB strength is not singular, but works in conjunction with the curing time and the cement-sand ratio. The longer the curing time and the higher the cement content, the higher the CB’s σucs. To avoid the time-consuming and costly problem of obtaining the strength of the CB from indoor experiments, an SVR model capable of predicting the uniaxial compression strength of CB specimens is proposed, which is optimized by genetic algorithm (GA) and particle swarm optimization (PSO) algorithm. The results of the three performance indexes (MAPE, MSE, and R2) show the superior performance of the GA-SVR and PSO-SVR models and the agreement of the predicted results with the experimental results, which indicate that these two models can accurately predict the σucs of CB.

Feb 3, 2022

By J. F. Barry

Newmont Mining Corporation and Barrick Goldstrike Mines, Inc. concluded an exchange of land and reserves in an agreement signed May 3, 1999.This exchange of assets allowed Newmont to develop the Deep Post underground mine from within Barrick’s Betze-Post open pit, thus reducing capital expenditures, lowering operating costs, and advancing the production schedule by nearly three years. Based on previous experience, Newmont is confident that the Deep Post underground mine can be successfully developed and operated within a large, active, open pit mine. The project also faces difficult geotechnical conditions including weak ground, scattered pockets of groundwater, and elevated rock temperatures.

Jan 1, 2000

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification (nickel, cobalt, copper, and manganese) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte, ammoniacal leaching (gas reduction or Cuprion), and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stems from the 1970s and 1980s and is not always easily accessible. This paper will detail the series of tests conducted and provide updated results obtained (high Ni/Co/Cu recovery with limited Mn/Fe), as well as comment on the potential treatment options on the product solution and residue.

Feb 1, 2025

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification such as nickel (Ni), cobalt (Co), copper (Cu) and manganese (Mn) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte; ammoniacal leaching (gas reduction or Cuprion); and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered the pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stem from the 1970s and 1980s, and are not always easily accessible. This article details the series of tests conducted and provides updated results obtained — high Ni/Co/Cu recovery with limited manganese/iron (Mn/Fe) — as well as comments on the potential treatment options on the product solution and residue.

Sep 1, 2025

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

By Fahimeh Dehghani, Louis Ackah, Tathagata Ghosh, Justin Godbold, Jia Liu, Meisam Peiravi, Manoj Mohanty, Azam Baharlouei

Primary economical deposits of rare-earth elements (REEs) are exhausting all over the world, and it has become necessary to find new sources and methods for their extraction. In addition, increasing the application of REEs in modern technological society has increased its demand globally. One of the important movements to compensate for the future shortages of critical metals is the recovery of REEs from recyclable materials. This paper presents a review of the classification and extraction methods, as well as general applications of REEs with emphasis on secondary sources such as coal and coal byproducts, iron ore tailings, apatite, and phosphate byproducts. An overview of the current state of knowledge on the various methods of REE beneficiation and extraction is covered. These methods include physical separation, as well as hydrometallurgical and bio-hydrometallurgical techniques. The application of these REE extraction techniques for enhanced recovery has been driven primarily by the unique industrial application of these important elements. This paper further explores the existing and potential environmental challenges associated with REE extraction. The authors have presented a wide array of literature, in-depth discussion of the subject, and a succinct summary of processes and relevant case studies.

Sep 23, 2020

By Qingming Feng, Jinhong Zhang

A study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature, and curing time significantly affect the mechanical property of geopolymermatrix. Through optimization, an above-100MPa compressive strength has been achieved with the geopolymerization products. The optimum working conditions involves 10MNaOH concentration, 14–15% water content, and curing at 90 °C in an oven for 1 day or at ambient condition for 3 weeks. Adding Ca(OH)2 does not help to increase the compressive strength of the specimen.Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength, even after a 1-month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS (scanning electron microscopy and energy-dispersive X-ray spectroscopy), XRD (X-ray diffraction) and ATR-FTIR (attenuated total reflectance Fourier transform infrared) are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method for applying fly ash as a high-strength water-resistant precast construction material.

Aug 17, 2020

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983

By P. H. S. W. Kulatilake, T. Hudaverdi, C. Kuzu

Prediction of blast fragmentation plays a key role for overall productivity of mines. In this study, a new multivariate analysis procedure for prediction of blast fragmentation is presented. Several blasts performed in various mines and rock formations worldwide were brought together and evaluated. An extensive blast database was created. Blast design parameters, the modulus of elasticity and in-situ block size were considered to perform multivariate analysis. A complete multivariate analysis procedure was applied in three steps. First, a hierarchical cluster analysis was used to separate the blast data into different groups of similarity. Two different groups were formed based on the elasticity modulus values. In the second step, group memberships were checked by discriminant analysis. The dominant parameters of the occurrence of the groups were determined. Also, discriminant analysis was used to determine the group membership of the respective blasts. As the last step, the multivariate regression analysis was applied to develop prediction equations for estimation of the mean particle size of muckpiles. Two different prediction equations were developed based on the rock stiffness. Validation of the proposed equations on various mines was performed. Prediction capability of the proposed models was found to be strong. The models are not complex and are suitable for practical use at mines.

Jan 1, 2011

By S. Mohanta, S. Chakraborty, B. C. Meikap

"An air dense medium fluidized bed separator is an efficient dry process for the removal of undesirable gangue material from run-of-mine coal. Its cleaning performance depends on a variety of operating parameters that are interrelated in unknown, complex ways. A literature review showed that these parameters' effects had been experimentally investigated using a traditional one-variable-at-a-time approach, which is highly inefficient and sometimes misleading because many of the parameters often interact with each other to alter the overall equipment performance. Also, it is realized that the interrelationship among these parameters can have a significant effect on equipment performance. Therefore, to correctly evaluate the effects of individual parameters as well as their interactional effects on the separation performance of an air dense medium fluidized bed, we conducted a scientific study based on response surface methodology. Empirical models for two key response variables, namely, product ash and combustible recovery, were developed and subsequently used for identifying an appropriate operating region to achieve optimum separation performance. Furthermore, the optimum performances predicted from the empirical models were validated against experimental data. Preliminary results show a strong interaction among the operating parameters investigated in this test program.IntroductionFluidization is widely applied in industry for its various useful features. In the coal industry, it is used in the air dense medium fluidized bed (ADMFB) separator for the beneficiation of run-of-mine coal. In this separator, a medium is created by suspending fine magnetite particles in an upward air flow, and this pseudo-fluid is used as the beneficiation medium, with the lighter coal particles floating to the medium’s surface while heavier particles sink to the bottom. This separation technique had been receiving a significant amount of attention worldwide in recent times for its specific advantages of low operating cost and less restriction for small capacities (Luo and Chen, 2001; Sahu et al., 2009; Dwari and Hanumantha Rao, 2007; Van Houwelingen and de Jong, 2004), but it is still not a well-established industrial practice because of the availability of efficient wet processing technology. However, with a revival of interest in the dry beneficiation of coal, in general, and ADMFB, in particular, there is once again a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have been made to make this process a competitive and viable option. The existing literature reveals that most of these research efforts had been essentially focused on the identification of a single parameter that has a key influence on separation performance, without taking notice of parameter interactional effect. For example, Luo et al. (2004) proposed a pressure drop number to distinguish separation performance without considering the bed height and gas velocity, which are intimately related to this proposed pressure drop number."

Jan 1, 2015

By Sunny Murmu, Gnananandh Budi

One of the most significant concerns in longwall ground control is the instability and failure mechanism of the coal wall. The current research uses FLAC3D to simulate panel 1 of the Adriyala Longwall Project, India, in order to evaluate the distribution of vertical stress and material failure mode, in and around the longwall face. Additionally, three distinct criteria are used to evaluate coal wall spalling: vertical stress distribution, maximum shear strain, and residual cohesion. A novel algorithm is also proposed to appropriately capture roof bed caving, shield installation and advancement, and coal extraction from the face. The findings of the modelling show that progressive longwall extraction creates an elliptical stress relief zone around the excavation void. During the peak stress phase, the height of the stress relief zone is greatest, whereas the width is highest during the main fall phase. As mining advances, the coal wall at the face line appears to lose its stress-bearing capability. Shear failure was the most common coal wall failure mode. Maximum spalling depth (MSD) and longwall face spalling index (LFSpI) were used to measure the extent and volume of coal wall spalling in FLAC3D. For panel 1 of the ALP mine, the MSD, and LFSpI were determined to be 3 m and 90.5 %, respectively. The mode of coal wall spalling was expected to be total or fragmented failure. The field observations and the numerical modelling findings were in good agreement. The compressive strength and deformation modulus of the immediate roof appear to have a substantial role in coal wall spalling. The results of the proposed numerical simulation exercise can help strata control engineers better detect the risks of coal wall spalling and enhance face control for safe and productive working environment at the longwall face.

Aug 8, 2023

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020