Search Documents

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world's first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930's in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world's largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By Jens Classen, Martino Gatti

"GENERAL PROJECT DATAThe Sparvo Tunnel is part of the “Variante di Valico” project, a new 65km (40mi) highway link between Bologna and Florence, designed to renew the existing A1 route which connects Bologna and Florence. It is composed of 2 x 2,5km (1,55mi) twin tunnels excavated inside a complex geological context, characterized by the presence of a series of surface landslides and methane gas.The inclination is 2,6 % and the minimum radius is 1.400m (4.600ft). The two tunnel tubes were excavated by a 15,6m (51ft) diameter EPB-TBM from summer 2011 to summer 2013. The internal diameter of the concrete lining is 13,6m (44,5ft), made up of precast concrete segments 2m (6,5ft) long and 70cm (28”) thick, being the largest and heaviest segments ever produced. Excavation went smooth apart from initial problems concerning clogging problems and a main bearing damage of the TBM, which are discussed in a further paper during the congress. No structural damage was observed until the end of the TBM drives.SITE OBSERVATIONS DURING THE POST-EXCAVATION PHASEThe first evidence of the stress state of the segmental lining appeared on November 20, 2013 inside the northern tube (1st drive). Ring No. 884 showed obvious signs of overstress, resulting in spalling and crushing of the concrete, and the subsequent bending of the reinforcement, as visible in figure 1.At this time the tunnel invert was already partially backfilled, and construction traffic was running through the tunnel. First safety measures included closing of the tunnel, and initial measurements of the displacements."

Jan 1, 2016

By A. E. Sears

The intent of geomorphic landform design is to mimic the function of the natural landscape. In a surface mine reclamation application, geomorphic landform design has the potential to mitigate stream loss. This research quantified features of reference landforms and performed computer modeling of a conceptual valley-fill design using geomorphic landform principles. A design was created using published design parameters with a software design tool (Carlson Natural Regrade with GeoFluv). Three additional designs, incorporating field-obtained regional geomorphic landform parameters, were completed and resulted in a geomorphic landform design specific to southern West Virginia. This work illustrates the importance of field determination of the ridge to head-of-channel input and drainage density parameters. Values of ridge to head-of-channel distance measured in this study were consistently an order of magnitude greater than software recommended values (SRV); SRV = 24 m (80 ft) versus field= 220 m (720 ft). Similarly, for the drainage density parameter, the software recommended range is 6 to 9 km-1 (80-120 ft/ac). The field measurements for central Appalachia quantified the drainage density to range from 5 to 5.3 km-1 (67-70 ft/ac). This affects Appalachian valley-fill stream construction by making the stream lengths shorter and the land slopes steeper with straighter headwater channels compared with areas in the southwestern United States. While the application of geomorphic landform design to surface mine sites presents challenges, this work provides support for future applications.

By E. J. Garrison

A.C. Noble presents a clear and concise summary of the factors pertinent to a competent reserve evaluation of a mineral occurrence. However, I believe that he confuses the difference between a resource and a reserve. By definition, a reserve estimate includes all known economic, legal, mining, metallurgical and environmental factors impacting the recovery of the product(s) found in the deposit. A resource estimate, however, is an estimate of what is there - what is available for exploitation and should not include economic and other considerations. Only after defining the resource, its extent, location, physical and chemical properties, can an intelligent selection process begin of the extraction and processing technologies most appropriate to the circumstances encountered. The early and almost certainly inappropriate application of these often cookbook choices has probably lead many companies to walk away from good properties. (How many mines have been found in others rejects?) An example of the process is the early selection of metallurgical samples, after encouraging values are found in a few holes or surface samples, in an attempt to determine the economics of the prospect. Unfortunately, the sampler does not know how representative of the occurrence the sample is because he does not know what the deposit looks like. As a consequence, the property becomes saddled with a bad metallurgical sample that is often inappropriately used in evaluating the deposit which it does not represent.

Jan 1, 1994

By Richard E. Sabaski

The demand placed on the mining industry in the past 15 years for increased production, coupled with lower grade ore and higher cost capital, has resulted in a noticeable increase in grinding mill sizes. The pressure to increase mill size continues. During the mid sixty's and early seventy's, ?larger? conventional ball mills were in the range of 13 - 16-1/2 f t. diameter (4 - 5 m) increasing by the mid 70's to 18 ft. (5.5 m) diameter. At the same time, autogenous mills expanded from 24 - 32 ft. (7.3 - 9.1 m) to the present 34 and 36 ft. (10.b and 11.0 m) diameters. These size pioneers of 16-1/2, 18, and 36 ft. diameter mills from Allis-Chalmers have been free from structural problems, because they were analyzed, modeled, designed, and field tested to meet the challenge.

Jan 1, 1981

By Mostafa Benzaazoua, Bruno Bussière, Mukendi Kongolo

The desulphurization process has been proposed over the last few years for acid mine drainage control at certain mines, which generate low to medium grade sulphidic tailings (-3 to +25 wt% S). The environmental sulphur recovery, which means the sulphur to be floated to produce a non-acid generating final tailings, depends mainly on the intrinsic neutralizing potential of the tailings. However, in some cases the sulphur cleaning is complicated by other parameters which affect the flotation probability of the sulphide particles. In this study, a number of tests were conducted with a Hallimond tube and Denver Cell on both pure mineral and mine tailings. To develop a better understanding of the mechanisms of non-selective sulphide flotation, three types of approach were investigated in this work: (i) pure pyrite at progressive milling degrees, (ii) artificial mix of pyrite and quartz at different calibrated granulometry and (iii) same composition tailings with 26 % wt sulphur at progressive milling degrees. The effect of the granulometry on the sulphide flotation was demonstrated both. The results allow us to define a granulometry model, which can then be considered in the whole desulphurization modeling.

Jan 1, 2000

By I. Iwasaki

The effects of percent solids, mill loading and grinding time on product size distribution and ball wear were studied in a laboratory ball mill for a taconite ore. Mild steel balls and HCLA steel balls were used to examine the role that ball hardness play in grinding. Net production of minus 325 mesh - material reached maximum at 70% solids, whereas the ball wear decreased as pulp density increased. HCLA steel balls ground the taconite ore finer than mild steel balls under otherwise identical conditions. Examination of ball surfaces with a scanning electron microscope suggested that grinding with mild steel balls involved nipping rather than attrition, whereas grinding with harder HCLA balls involved both nipping and attrition.

Jan 1, 1984

By Charles B. Manula

This paper describes the development of a mathematical model for simulating the behavior of a longwall coal production system. The longwall simulator is a design simulator incorporating both deterministic and stochastic methods to calculate: (a) the size and density of support; (b) the cutting force, power requirements and haulage speed for the loader-shearer; (c) the conveyor size, speed and power requirements; and (d) delay generation at head and tail-gates and the longwall face.

Jan 1, 1978

By L. H. Michaud

A mining company plans to extend its surface coal-mining operations in central Pennsylvania. Although the proposed site contains pyritic material, the results of the acid-base accountings for the site shows an overall Neutralization Potential to Maximum Potential Acidity Ratio (NP:MPA) of 4.26:1 for the entire site. The pyritic material is, however, associated with the lower of the three seams to be mined. If traditional dragline-mining methods are used, this would result in the acidic material being placed at the top of the spoil piles, exposing it to air and water, and therefore to the formation of acid mine drainage (AMD). Further concerns are associated with the fact that the alkaline material is not distributed evenly over the mine site. To prevent the formation of AMD, the company has proposed to mine the area using truck-shovel mining methods. This technique offers a more flexible alternative for cut sequencing and for the selective placement of waste material. Working with the Department of Mineral Engineering at The Pennsylvania State University, amine plan was developed for this site. This plan results in the layering of the alkaline and acidic spoil to achieve an overall net alkalinity in all spoil areas. Therefore, mining this site should not result in the formation of AMD.

Jan 1, 1996

By K. Häge

"Die Nachhaltigkeit der Braunkohlengewinnung in der öffentlichen Wahrnehmung wird nur weiter erfolgreich kommuniziert werden können, wenn durch konkretes Handeln glaubhaft gezeigt wird, dass die offenen Fragen fair und solide beantwortet werden. Dazu gehören insbesondere die neue innovative technische Lösung sowie das sensible Interessenmanagement. Die Braunkohlenindustrie hat gelernt, dass Offenheit und nicht zuletzt das beständige Bemühen um den Meinungsaustausch mit ihrem Umfeld wichtige Elemente sind. Der in Jahrzehnten erworbene Schatz an Glaubwürdig-keit ist eine Basis, auf der die Braunkohlenindustrie ihre Zukunft gestalten kann. Darüber hinaus sind politische Rahmenvorgaben erforderlich. Das öffentliche Interesse an einer sicheren und preiswerten Energieversorgung unter Einschluss der Braunkohle ist unverzichtbar. In diesem Kon-text kann dann die Braunkohle die an sie gerichteten Fragen der Ökonomie, der Ökologie und der Sozialverträglichkeit auch mit Hilfe von Indikatoren beantworten.ABSTRACTThe discussion of the sustainability of lignite mining can only be continued successfully if the indus-try acts in a practical manner and demonstrates trustworthiness by responding fairly and reliably to open questions. This includes new and innovative technical solutions as well as the sensitive management of interests. The lignite industry has learned that openness and the constant effort to exchange viewpoints within their environment are all essential elements. The credibility that has been gained over the decades is the foundation on which the lignite industry can build its future. Beyond that a framework of political guidelines is necessary. Public interest in a secure and inex-pensive energy supply that also includes lignite is indispensable. In this context, the lignite industry will then be able to answer the questions which are directed at them and concern the economy, ecology, and social tolerability also by indicators."

Jan 1, 2005

"INTRODUCTION Twin Metals Minnesota (TMM) (operating as a joint venture between Duluth Metals and Antofagasta PLC) assumed control of the property in 2010. Amec became involved with the project in 2011 and in 2012 incorporated additional drilling in order to update historic resource estimates. The Maturi geological model and resource estimate was updated in 2014 to incorporate additional information obtained during 2013 and 2014 drill campaigns. In 2017, Amec was purchased by the Wood Group and is now known as Wood. Geology The Twin Metals Minnesota (TMM) Maturi, Maturi Southwest, Birch Lake, and Spruce Road properties are located in northeastern Minnesota (Figure 1). This talk discussed the Maturi deposit only, although all four deposits share similarities. The following geology is summarized from Peterson and Severson (2002).Maturi lies within the Superior Province of the Canadian Shield which is exposed in central and northeastern Minnesota and extends northward into Ontario. In eastern Minnesota, the Midcontinent Rift System developed during crustal scale extension in the Mesoproterozoic Era. The rift system is traceable, as exposures of mantle-derived tholeiitic to subalkaline mafic lava flows, intrusives, and rift-filling fluvial sedimentary rocks, and in the subsurface as a gravity anomaly (high), from the eastern end of Lake Superior, arcing west across the lake basin, and extending south-southwest to northeastern Kansas. Intrusion of the Duluth Complex, circa 1,108 - 1,099 Ma, was related to rifting and is co-genetic with the North Shore Volcanic Group mafic volcanic rocks that form the hanging wall of the Duluth Complex to the east. Cu-Ni-precious metals (PM) mineralization including Pt, Pd, Au and Ag within the Duluth Complex is hosted by mafic to ultramafic intrusive rocks that are part of the overall intrusive complex. The Duluth Complex is defined as a more or less continuous mass of mafic to felsic plutonic rocks that extends northeastward for more than 170 miles (275 km) in an arcuate fashion from Duluth nearly to Grand Portage in Minnesota. It is bounded by a footwall of Paleoproterozoic sedimentary rocks and Archean granite-greenstone terranes (Peterson and Severson, 2002), and a hanging wall largely of comagmatic anorthosite, rift related flood basalts, and hypabyssal intrusions of the Beaver Bay Complex. Mineralization is hosted in the basal mineralized zone (BMZ) of the South Kawishiwi Intrusion (SKI). The SKI magmas intruded sub-horizontally between hangingwall Anorthositic Series (AN) rocks and footwall granitic rocks of the Neoarchean Giants Range batholith (GRB). The Maturi local geology and the deposit footprint (shaded orange) is shown in Figure 2."

Jan 1, 2018

By Richard C. Corson

The new 9300 TPD sinter plant being built for China Steel Corporation is incorporating the latest computer technology for plant control systems. The control system will use a central computer and distributed micro-processors to control instrument loops and switching logic in the blending yard and sintering plant. All plant functions, including combustion and fan controls, will be controlled by remote microprocessors located throughout the plant, and connected by a communications link to the centrally located computer and control room. The design, programming, construction and operation of a microprocessor based control system presents new challenges to the control engineer. With microprocessors in the control system, more power exists in the individual control loop and many supervisory functions may be added at the loop level. The specification of the microprocessor system and the resolution of hardware design and control system design can lead to development of powerful systems capable of higher level control and optimization functions

Jan 1, 1981

By Alvaro Veizaga, Samuel Cuellar

In recent years, Industry 4.0 has generated a change in the way companies in various industrial sectors design, produce and deliver products and services, and is focused on the interconnection of systems, the advanced access and management of large amounts of data in real time, and the implementation of emerging technologies such as the Internet of Things (IoT). Artificial intelligence (AI), machine learning (ML), digital twins (DT), robotics, virtual and augmented reality (VR/AR), among others [1]. DTs are accurate and dynamic virtual models that replicate physical systems, where it is possible to simulate and optimize operations before implementing real-world changes [3]. These features make it possible to reduce investment costs, minimize risks and improve strategic decision-making. These benefits are of utmost importance for tailings storage facilities (TSF), since they are facilities aimed at the safe storage of tailings and with the constant need for growth [4]. This paper evaluates the applicability of a DT in a TSF from a conceptual perspective, providing the advantages of its implementation, but also the barriers identified in the industry based on the authors’ experience.

Feb 1, 2025

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be rehandled. Prior studies have shown that by only changing blasthole timing with the same blast design, fragmentation and throw alter. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum interhole delay for fragmentation has been found by studying timings from 0 millisecond (ms) to 45 ms. Instantaneous timing between holes increased the throw by more than 31 m (100 ft), but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw.Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.”Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is rehandled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators have allowed for precise delay timings to be used between rows, holes and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation."

Jan 6, 2017

By Jed Greenwood, Lyall Workman, Michael Haggerty, Russell Sheets

Draglines often work from a position on the active highwall or spoil side bench to remove undisturbed waste material and spoil in the previously mined pit. To protect the dragline crew members and the machine, it is necessary that the highwall remain stable while the dragline is present on the bench. In the past several years, we have been involved in determining the causes for highwall failures that included the dragline. While there have been no injuries and limited dragline damage with these incidents, the potential certainly exists for a more serious outcome. In all cases, the operation had completed a geotechnical study to support the ground control plan and pit designs. However, all these incidents included aspects that would not likely have been identified in studies to determine highwall and spoil designs to support ground control procedures. In general, these events included aspects that were localized and would have been difficult to identify in initial slope stability studies either observationally or during the soil testing and modelling efforts. Although the authors do not have quantitative evidence of this, it does seem there has been an increased number of events in recent years. This may be due to loss of institutional knowledge, mining in more challenging areas, or simply an increase in localized variation. This paper will describe some of the issues we have seen and what the causes of failure were. It becomes clear that avoiding similar incidents in the future requires on-going observation and inspection of active highwalls and spoil benches to try and identify local variability and impact on mining. The information can proactively be used to update stability modeling of any concerning issues to determine likelihood of problems and to develop solutions.

Feb 1, 2025

By Wi11iam I. Rau

In the recent past, there have been numerous projections of the capital requirements for additional mine and processing capacities required to meet projected non-Communist World demand for minerals during the next 15 years. A consensus judgment would place this currently at $14 billion per year, with the largest expenditures required for increases in aluminum and copper production. Until the early 1960's, internally-generated funds were used to finance nearly all of the large mining companies' capital requirements. Since that time, however, the enormous rise in capital costs per ton of capacity, accompanied by a relative stagnation in the financial condition of many of the major mining companies, have caused the industry to begin to rely on external sources for financing expansion, most notably, project financing from commercial banks and institutional lenders. Seven years ago, it was estimated that, in the five-year period 1972-1976,75% of the total capital requirements of $10 billion per year would come from internally-generated funds, with the balance to be provided by external sources. l There is little doubt that, in the coming decade, the percentage provided by external sources will increase. There should be little difficulty in attracting the necessary investment within the U.S., particularly in view of the expected continuation of companies in diverse industries seeking mineral investment opportunities. The more serious question lies in the availability of internal and external sources of funds for the expansion of mine and smelting capacity in the developing countries. Recently, R. F. Mikesell projected an average annual investment of $4.7 billion (in 1977 prices) over the 1977-1990 period would be required from foreign sources to expand metal producing capacity in developing countries. Mikesell concluded that external financing of mining projects in the developing world has averaged less than $1 billion per year over the past five years, thereby requiring more than a quadru1ling of this financing over the next decade.

Jan 1, 1978

By H. M. Woodrooffe

In the U.S.S.R. three of the world's major-known phosphate deposits are located. These have an estimated reserve of 2,600 million short tons of contained phosphorus. The best known lies in the "Khibiny Massif', an alkalaic rock formation some 600 square miles in area with mountain peaks rising to an altitude of 3300 ft above the surrounding terrain. Location and Climate The Khibiny Massif lies north of the Arctic Circle in the Kola Penin-sula, 100 miles south southeast of Murmansk, at a latitude of 67° 30' north and a longitude of 35° 30' east. It is serviced by rail from Murmansk and Leningrad (900 rail miles south). Figure 1. The phosphate operations are centered about the two cities of Apatity and Kirovsk. The former has a population of 35,000 and is on the Leningrad¬Murmansk railway. Kirovsk, 15 miles to the east, is now a city of 85,000. The region is at the limit of the tree line with most of the ground cover typical tundra. The mean annual temperature is -4°C and, in a normal year, precipitation occurs on 240 days. Because the temperature does not exceed freezing for 300 days each year, virtually all of the precipitation is snow. The two towns are nestled between mountains and, because of the weather, extensive avalanche control systems incorporating major engineering construction have been introduced to divert snow slides away from the populated areas. General Kirovsk was first settled in 1923 and the apatite occurrences were recognized shortly after. In 1933, the first concentrator for the recovery of the mineral was completed, producing in its first year of operation 170,000 tons of concentrate. With the growth and demand for phosphate in the U.S.S.R., a second concentrator was erected at Apatity. It calve on stream in 1963. Because of the severe climate, in the early days mining was limited to 85 days per year. With the introduction of new techniques and improved mining methods, the season has been extended to 115 days.

Jan 1, 1972

By J. J. Gusek

The Riley Pass strip mine is an abandoned uranium-bearing lignite deposit in Harding County, South Dakota, covering about 150 acres of highwalls, pit floor and mine spoils exhibiting elevated levels of radioactivity. Six reclamation design alternatives were developed, ranging from doing nothing to reclaiming to approximate original con-tour. The alternatives were evaluated for expense, site stabilization, and mitigation of public safety hazards. A comparative economic evaluation on three of the alternatives was completed for the Forest Service in selecting an alternative and substantiating federal funding requests. This evaluation included economic impacts associated with physical and radiologic health hazards, affects on recreational users, socioeconomic impacts and environmental improvement.

Jan 1, 1995

By Robert C. Pease

Siskon Gold has started gold production at the San Juan deposit in northern California. The mine is located about 27 km (17 miles) north of Nevada City, CA (Fig. 1). It is scheduled to be-come the largest underground gold mine in California. It is situated in the western foothills of the Sierra Nevada Mountains in the Mother Lode gold belt. The property consists of 8 km2 (2,000 acres) of patented land. It is situated in a topographically high area known as San Juan Ridge, which is 213 m (700 ft) above and between the Middle Yuba and South Yuba rivers. The elevation is between 790 and 914 m (2,600 and 3,000ft) above sea level. Annual precipitation averages 1,346mm (53 in.). Most of that falls between November and April.

Jan 1, 1996

By Ryan Ward

The Missouri River Intake Screen Structure and Tunnel (MRISST) is one phase of the Red River Valley Water Supply Project (RRVWSP), a vital piece of infrastructure in the state of North Dakota to transport water to drought-laden communities in the eastern half of the state. The scope of work consists of constructing a cofferdam in the Missouri River, mining a 1,600-foot by 74-inch tunnel from a secant pile shaft near the riverbank into a cofferdam, and erecting a 40-foot Y-shaped vertical pipe structure in the cofferdam to support the intake screens. Construction personnel worked in the river through the North Dakota winter to construct the cofferdam and contended with high hydrostatic pressures and raveling sands, gravels, cobbles and boulders while mining the tunnel. Diligent planning and meticulous execution were essential to overcoming the challenges encountered below the Missouri River.

Jun 13, 2023