Search Documents

By Arman Hazrathosseini, Ali Moradi Afrapoli

Fleet management systems (FMSs), as a pivotal part of any surface mining operation, need to evolve from conventional to intelligent systems because of both Mining 4.0 requirements and some shortcomings inherent in conventional methods. However, this novel transformation needs to be investigated technically and strategically. To this end, previously published research works on intelligent FMSs are explored to track the latest status of these third-generation frameworks within the surface mining context. Their underlying models are then compared in terms of five categories of allocation and dispatching features to pinpoint the technical gaps ignored. Having drawn the future lines of research, the present work then leverages the popular SWOT analysis method to outline the strengths, weaknesses, opportunities, and threats associated with the advent of these intelligent FMSs in mines of future. By and large, the analysis indicates that advantages outweigh disadvantages. Solutions are offered to address the existing weaknesses and threats.

Apr 1, 2024

By I. S. Parrish

One of the most common errors uncovered while performing a reserve, or resource, audit is not in the geological modeling or grade problems due to poor sampling, prepartion or assaying. The error most commonly found is in tonnage or, more specifically, in the tonnage factor - that factor applied to volume to derive tonnage. Tonnage factors In the metric system, the tonnage factor is the density, or specific gravity. Specific gravity (Sp.g.) is defined by Dana (1947): • "The specific gravity of a mineral is the ratio of its density to that of water at 4° C (39.2° F). • "Density is the mass of the unit volume or weight of the body divided by the weight of an equal volume of water." When Sp.g. is multiplied by the metric volume it yields metric tonnes. In the English system, the tonnage factor is usually expressed in cubic feet per short ton (cu ft/st). When the volume in cubic feet is divided by cu ft/st, the resulting figure is in English short tons. Table 1 gives the cu ft/st factors equivalent to specific gravities from 1.6 Sp.g. to 5.8 Sp.g. The table is based on the following equation: cu ft/st = 0.9072 divided by Sp.g. times 0.02832 The blase attitude that most geologists have toward tonnage factors is echoed in the prevailing definitions of Reserves and Ore, as provided by the US Securities and Exchange Commission (S.C Form S-18), Canadian National Policy 2A and the SME Proposal for Reporting Terminology (SME February 1991). In each case, it is stated that "quantity" (SEC, SME), or "tonnage" (Can.2A), "is computed from dimensions revealed in...." etc. Unfortunately, "dimensions" do not directly yield tonnage. Dimensions must be factored by density to derive tonnage.

Jan 1, 1993

By T. I. Nelson

Natural aggregates, primarily stone, sand and gravel, are recovered from widespread, naturally occurring mineral deposits and processed for use primarily in the construction industry. They are mined, crushed, sorted by size, and sold either loose or in concrete products to build roads, houses, buildings, and other structures. Smaller quantities are used in agriculture, cement manufacture, and industries employing chemical and metallurgical processes. The growth of cities, their buildings and the highways that connect them have created demand for enormous quantities of aggregates. The aggregates industry is the largest mining industry in the United States in terms of production by weight, volume and by number of active operations.

Jan 1, 2005

By F. Calizaya

This paper explains and discusses a computer program developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain project, Nevada.

Jan 1, 1994

By Mirko Martini, Marcelo Benaglia, Andrea Codalli

Riachuelo Lot 3 forms part of a sanitation programme being implemented in Argentina to relieve the Riachuelo river basin from its current contamination. The programme, by far the most important in its kind in the country during the last decades, will expand the sewage capacity of Buenos Aires and will benefit an area of 4.3 millions inhabitants by intercepting a number of waste water discharges and conveying them to a new treatment plant prior to final discharge into the Rio de la Plata. The project foresees amongst other works the construction of an onshore 48 m deep shaft at the outlet of the treatment plant plus a 4,3 m inner diameter outfall tunnel of 12 km length. The last 1.5 km of the alignment is fitted with 34 vertical risers jacked from inside the tunnel to allow the discharge and dilution of the treated effluent into the Rio de la Plata. This paper describes the peculiarities and challenges, both in terms of design and in terms of construction, of the outfall tunnel, which was entirely bored under the Rio de la Plata using a 5.2 m cut diameter Tunnel Boring Machine (TBM). On one hand, the tunnel segmental lining was designed to work in tension during the system flow rate peaks while on the other the tunnel excavation faced a variety of complex conditions, such as crossing water bearing permeable soft ground formations and advancing at face pressures in excess of 3,5 bars for the entire route.

Jun 13, 2021

By S. G. Britton

Thin seam mining presents unique challenges when management or economic conditions require significant productivity increases. These challenges are increased depending upon the presence of various external factors such as labor unions, Federal and state regulations, and market characteristics. This paper explores the turn-around situation occurring at Tanoma Mining Company (TMC), a medium-sized underground coal mining company in central Pennsylvania, USA. Using a systematic approach of improving management controls and direction, labor relations, and communications, coupled with an intensive upgrade/rebuild/replacement program for equipment and systems used at the mine, TMC has begun reversing its' cashflow position from negative to positive within two years.

Jan 1, 1991

By M. Prud’Homme

Potash is an important natural mineral used largely as a fertilizer in the production of food and fiber. About 93 percent of all potash consumed globally is used in agriculture as fertilizer. The balance is used to manufacture potassium chemicals. Most potash is extracted by conventional underground mining methods. Solution mining is used when underground deposits are irregular and very deep. The other main production method involves the evaporation of brines in shallow salt lakes, followed by the harvesting of potassium minerals.

Jan 1, 2005

By James E. McNulty

The planning and development of new coal mines is requiring the increased use of geologic, geologic engineering and hydrogeologic investigations. This is caused in part by the fact that new mines must deal with less favorable conditions than existing mines as well as higher costs of development and in part by the dictates of regulatory authority. High costs of new mines require greater reliability of geologic assessment using best available geotechnical and geophysical methods and technology. Although the increased cost of additional subsurface data is significant, the more important factor may be the impact on project lead time.

Jan 1, 1981

By Willard A. Murray

Investigations of underground coal gasification (UCG) have been actively pursued by the U.S. Department of Energy since the early 1970s; the Lawrence Livermore National Laboratory (LLNL) conducted its first field experiment in 1976. In conjunction with field and laboratory studies of the process of recovering energy in the form of combustible gases from the burning of coal deposits in situ, an extensive environmental program has been conducted at LLNL under the auspices of both the U.S Department of Energy and the U.S. Environmental Protection Agency. This program has focused on groundwater contamination and ground surface subsidence caused by UCG. The material presented in this paper is a summary of results from the environmental studies of UCG activities conducted by LLNL as described by Mead, et al. (1981) and supplemented by the author's experience with this program in 1980 and 1981. The following sections describe specific groundwater contamination and surf ace subsidence problems encountered during field experiments in northeastern Wyoming, and will discuss implications of preliminary findings from geohydrological investigations of a site in southwestern Washington. Finally, possible environmental control technologies that are most likely to be effective in mitigating environmental impacts are discussed.

Jan 1, 1982

By Timothy D. Arnold

Barrick Gold’s Bullfrog underground mine, near Beatty, NV, was established as an after-thought to the main open pit. As open pit ore dwindles, the underground mining became increasingly more important as an ore source, and to the overall economics of the project. This situation is similar to many other mines. Today, there is a move towards underground mining in the United States. There are inherent problems in starting and operating underground mines in the shadow of any open-pit operation. Several attempts were made at the Bullfrog Mine for productive increases. Some were successful, while others were not.

Jan 1, 1996

By Jack T. Work

Spiraling costs in every segment of the open-pit mining cycle is a fact of life that every operator must reckon with. The introduction of various shock absorbing devices for rotary drilling is one recent innovation that may significantly reduce overall drilling cost, increase drill availability, and lower maintenance requirements. In a recent all-inclusive test in taconite ores, shock absorbers on Bucyrus-Erie BE 60R and Gardner¬Denver GD 120 rotary drills were directly responsible for overall savings of up to $41.06 per hour. What is It? A shock absorber is simply a device installed between the rotary drive head and drill steel that cushions the two. It functions in the same manner as springs and shocks on an automobile. Some benefits associated with use of the tool are readily apparent on a daily basis; other benefits are realized over longer time intervals and through continued use. A properly designed shock absorber will: •protect the drill from severe vi¬brations, improve rock bit performance, allow application of the best weight-on-bit and rotating speed under all drilling conditions, •function effectively over a wide range of applied bit weights, • have a spring rate soft enough to perform its primary function of absorbing both rotary and vertical vibrational forces generated by rough drilling, •be reliable and subject to as little maintenance as possible, •be easy to install and remove, and • be of such an economic benefit so as to offset the added expense of its application. A shock absorbing tool developed by BJ-Hughes Inc. was used in a recent test. The "Smoothdrill" is just one of the products currently available. This unit absorbs both rotary and vertical shock loads and has no mechanical parts so lubrication is unnecessary. A rebuild of the unit consists of removing the worn rubber element and inserting a new element, an operation taking less than one hour. Minimizing Vibrations Severe vibrations on a blasthole drill operating in broken and discontinuous formations have visible effects. These vibrations often cause structural damage when allowed to' continue, resulting in fatigue cracks in the mast and related structural components in the drill. When rough running formations are encountered, drilling must be interrupted and possibly shut down. Usually, the drill operator resumes drilling using less down pressures and various rotational speeds until firmer drilling is encountered. An effective shock absorber can substantially reduce these vibrational forces so more down pressure can be applied in bad ground. It is generally accepted that longitudinal vibrations and cyclic forces are more effectively reduced if a tool is designed to incorporate a relatively "soft" shock absorber. The softness of any shock absorbing tool is best judged by its spring rate-the weight required to produce a given amount of deflection, commonly expressed in units of kg per mm or pounds per inch of deflection. All shock tools use a resilient member such as rubber springs, steel springs, fluid, or gas springs to absorb

Jan 4, 1980

By Ü. Atalay, G. Alaeddinoglu, G. Özcengiz, G. Özbayoglu, Z. Özdemir

In this study, bacterial pre-treatment was applied before cyanidation in order to enhance the solubilization of silver from Artvin-Kafkasör ore Direct cyanidation process was found inefficient to recover silver from the ore. Only 40.36% silver recovery was obtained with direct cyanidation while silver recoveries of above 60% were obtained after bacterial treatment. Thiobacillus ferrooxidans was used as the microorganism in pretreatment tests. Effects of various parameters such as pulp density, duration, inoculum size and particle size on silver recovery have been investigated in this study.

Jan 1, 2001

By A. G. Taylor

High value materials, such as gold, platinum and other precious metals are subject to loss through unauthorized removal from mines, smelters, refiners, and other places where such materials are processed. A study published in 20011 determined that between 1994 and 1998 an average of 603 kilograms of gold per year was stolen from South African miners and subsequently recovered. This does not include the gold that was stolen but not recovered. At 2011 prices, 603 kilograms of gold would be worth approximately $33 million. Mine security personnel believe that the unrecovered stolen gold far exceeds what is recovered2. Traditionally, metal detectors have been used to screen personnel leaving secure areas to discourage such unauthorized removal. However, with the current near-record prices of gold, platinum, and other precious metals, it has become worthwhile for people exiting a facility to walk out with quantities of product that are too small for ordinary metal detectors to register, resulting in substantial financial losses.

Jan 1, 2012

By S. K. Singh, P. R. Sheorey

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By S. Mischler, J. Noll, G. Schnakenberg, A. Bugarski, M. Crum

Diesel particulate filter (DPF) systems and biodiesel fuels are two of the most promising technologies available to the mining industry to reduce the exposure of underground miners to diesel particulate matter (DPM). A study has been conducted to estimate the potential of DPF systems and biodiesel blends to reduce DPM emissions from production vehicles. Results of testing three DPF systems in an isolated zone showed 88% to 99% reductions in elemental carbon concentrations. The test results also show that biodiesel blends, B20 and B50, reduced the elemental carbon concentrations in the mine air by 26 and 48 percent, respectively.

Jan 1, 2004

By E. Piesch, M. Urban, G. M. Hassib

INTRODUCTION In radon dosimetry diffusion chambers with passive [a]-detectors are now in current use to investigate the long-term accumulated indoor exposure of radon and daughters. For the diffusion chamber developed at Karlsruhe the electrochemical etching technique (ECE) was applied to reveal [a]-particles in polycarbonate plastic detectors. Compared to conventional etching, the main advantages of the ECE are the large track diameter, simple track counting in a single field of about 1 cm2, stability of the latent tracks to humidity and temperature and ability for a long-term accumulation up to 1 year. The electrochemical etching system was designed to etch in one run about 101 foils by using a 200 W high voltage generator. The commercial available radon dosimeter system is applied for a country wide program of measuring radon in dwellings. Because of an increasing interest of radon monitoring in mines, environmental monitoring and personnel dosimetry the properties of several track etch detectors have been studied. In the comparative study, Makrofol E, LR 115 and CR 39 were used in the diffusion chamber to investigate the etching techniques, the relative efficiency, the measurable [a]-energy range, and the counting statistic for the measurement of radon concentration. THE KARLSRUHE DIFFUSION CHAMBER The design of the Karlsruhe diffusion chamber is presented in Fig. 1. The upper part of the chamber is closed by a fibreglass filter to separate radon from aerosols, heavy dust particles and radon decay products. Inside the diffusion chamber [a]-particles from radon and daughters are detected by two passive radon detectors, one on the bottom of the chamber and the other in front of the filter. With the fibreglass filter applied the diffusion time is about 1 minute for radon. Therefore, also short-term variations in the radon concentration are recorded by the track detector. Mainly because of the short halflife of thoron (56 s) only about 7 % of the thoron concentration is expected in the diffusion chamber. Radon monitoring provides the estimation of the long-term accumulated mean value of the radon concentration with a lowest detectable concentration of 0.1 pCi/1 after 3 months accumulation by using polycarbonate track etch detectors, an electrochemical etching technique and track counting in a single field of 1 cm2. The diffusion chamber was optimized for the polycarbonate track detector with respect to chamber geometry and detector position [1]. Table 1 presents data for 3 different diffusion chamber designs. The radon sensitivity of the diffusion chamber depends on the [a]-energy discrimination and the angular response of the [a]-track detector. The difference between foil No 2 and foil No 1 can be explained by an additional plate-out effect of radon daughters on foil No 3. The high sensitivity of foil No 3 compared to that of foil No 2 is caused by an increase of the effective volume and the effective area for [a]-particle from radon and from plated-out decay products, respectively. Additional experiments have been performed in order to investigate the electrostatic properties of the plastic material and the properties of the diffusion filter [1]. The properties of bare a-detectors were compared with those inside the diffusion chamber. In contrast to laboratory results, dust particles deposited on the detector surface or in the environment of the detector obviously affect the reproducibility of the bare detector significantly. After 4 months exposure in dwellings the scatter of 10 dosimeters exposed in the same room exceeds a factor of 3 compared to 15 % for the diffusion chamber. COMPARATIVE STUDY OF TRACK ETCH DETECTORS Detector types and evaluation technique In the comparative study the properties of the following plastic track etch detectors have been applied: - LR 115 from Kodak Pathé, France, is a red dyed cellulose nitrate layer of 13 µm thickness on a 100 µm thick polyester support. The holes appears as bright spots in a dark red background. In an optical microscope counting of through etched [a]-tracks which must penetrate the detector layer - CR 39 from Pershore, England, is an ally1 diglycol carbonate plastic of about 300 m thickness. The normal etched [a]-tracks are counted by an optical microscope and the ECE [a]-tracks by a microfiche reader.

Jan 1, 1981

By R. E. Hamilton

It is more than ten years since the first fully automated process using a computer started operation. Computer control has become common in a number of process industries, yet in spite of the tremendous incentives which ere present, there are only a few computer installations in the mining industry and none of these has announced successful control of a process. Recognizing that one of the reasons for this slow progress is the lack of adequate mathematical models of the various processes involved, the author's company started a project in the summer of 1966 to develop such models. It was early recognized that the existence of a major disturbance input, in the form of the mineral composition of the feed prevents most flotation plants from attaining a steady state condition. This makes the custom¬ary method of developing correlations from steady state plant data inapplicable and requires a more fundamental approach.

Jan 1, 1968

By Erik Sundström, Magnus Nygren

Having seen significant improvements to accident rates in the last 40 years, companies in the Swedish mining industry now show a greater focus on the development of safety cultures throughout their organisations and workplaces. However, there is a lack of research examining the different safety initiatives and strategies practiced in the industry today. This study explores the potential influence and consequences such initiatives may have on the development of safety cultures in the Swedish mining industry. Twelve interviews with experts on safety initiatives from four different Swedish mining organisations were conducted and analysed in a process based on qualitative thematic analysis to identify notable connections to safety culture development. The results of these interviews highlight proclivities in the implementation and use of safety initiatives such as subjects of focus, methods and desired effects. This enables the interpretation of the conceptualisation and methods for the development of safety culture in these organisations based on their approaches to safety development. We believe the results of this study can serve as support for discussions on safety culture development in the Swedish mining industry, and be of interest for international mining industries, in addition to approaches to research in this field. However, we also believe it is important to emphasise the opportunities to approach safety culture in mining from different perspectives than those common today.

Jul 19, 2023

By I. R. Firth, D. L. Taylor

The ability to accurately model the movement of grade boundaries during a typical bench blast would be of significant benefit to mine operators. The movement of grade boundaries during the blasting process may have significant impact on grade recovery if not accounted for. The paper describes the preliminary stages of a research project which combines numerical blast models and conventional mine planning software to allow practical use of the results of a numerical blast simulation. A two dimensional bench blast is simulated using the Universal Distinct Element Code (UDEC). The results of the simulation are used to provide input to the Surpac mine planning package which can be used to generate grade control plans.

Jan 1, 2001

By M. A. D. Azevedo, J. D. Miller, R. Kobler, E. Mutkowska

Up to 3 million tons of automotive shredder residue (ASR) is generated annually in United States. Plastics are the most valuable component of the ASR material making up approximately 25% of the total weight. In order to reuse these plastics, a selective process is required to separate each plastic, with very high purity and favorable economics. One separation technique, which may be able to selectively recover the plastics from ASR, is flotation. The preliminary flotation results have demonstrated that acrylonitrile-butadiene-styrene (ABS) and polycarbonate (PC) can be selectively separated from the model ASR feed, the PC/ABS/PA 66 system, by appropriate control of the surface chemistry.

Jan 1, 2001