Search Documents

By J. D. Potts

Installation of a horizontal air blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong coanda effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector to bailing airflow ratio, and a 5.1-cm (2-in) gap between the shroud and ground. The shelf was 15.2-cm (6-in) wide and located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2009

By Sandip K. Mukherjee

This paper describes the application of pressure foam to control respirable dust in a double-drum longwall mining section. The feasibility of passing an adequate quantity of pressure foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The de- tails of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1984

By Christa Overby

As part of the City of Portland, Oregon?s East Side Combined Sewer Overflow Tunnel Project, nine separate 2,130 mm (84-inch) diameter reinforced concrete pipe microtunnel drives totaling approximately 2,380 m (7,808 ft) are being constructed to divert flows from several of the existing outfalls to the main tunnel. The drives were constructed in challenging ground conditions that include soft soils under the ground-water table, large amounts of wood and metal debris, and close proximity to sensitive structures. While all of the drives will be addressed, the focus of the paper will be on the 931 m (3,055 ft) continuous drive connecting Outfall 46, currently the longest microtunnel driven in North America.

By F. F. Roberto

Many techniques that are used to characterize and monitor microbial populations associated with sulfide mineral bioleaching require the cultivation of the organisms on solid or liquid media. Chemolithotrophic species, such as Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans, or thermophilic chemolithotrophs, such as Acidianus brierleyi and Sulfolobus solfataricus can grow quite slowly, requiring weeks to complete efforts to identify and quantify these microbes associated with bioleach samples. Real-time PCR (polymerase chain reaction) assays in which DNA targets are amplified in the presence of fluorescent oligonucleotide primers, allowing the monitoring and quantification of the amplification reactions as they progress, provide a means of rapidly detecting the presence of microbial species of interest, and their relative abundance in a sample. This presentation will describe the design and use of such assays to monitor acidophilic microbes in the environment and in bioleaching operations. These assays provide results within 2-3 hours, and can detect less than 100 individual microbial cells.

Jan 1, 2009

By William R. Yernberg

The combined 78th Annual Minnesota Section of SME Meeting and 66th Annual University of Minnesota Mining Symposium was held April 19 and 20, 2005, in Duluth, MN. More than 300 mining professionals, including engineers, executives, mining managers and suppliers, from throughout the United States and eastern Canada attended the meeting. This year’s theme was “Global Demand: A Window of Opportunity.” The meeting included a keynote address, technical presentations and a trade show. The atmosphere at this year’s meeting was upbeat. The iron ore mining industry in Minnesota is experiencing one of its biggest turnarounds in history. Because of greater demand, iron ore prices increased 20 percent during 2004 and 71.5 percent so far in 2005.

Jan 1, 2005

By Ian Hutchison, Ted Sluder, Jack Caldwell, Don Moore

Introduction The Cannon mine at Wenatchee, WA has recently been brought into operation to recover gold from the sandstones of the Swauk formation. The mine is a joint venture between Asamera Minerals (US) Inc. and Breakwater Resources. A tailings impoundment was constructed to impound 2.7 to 3.6 Mt (3 to 4 million st) of tailings at 1.8 kt/a (2000 stpd) over about five years. This paper describes the design and construction of the impoundment. In particular, it describes the 100 m (300 ft) high earthfill embankment that is the main feature of the facility. Project environment The project is located on the outskirts of Wenatchee, a town of about 40,000 people. The town is situated on the flat alluvial terraces beside the Columbia River. The Cascade Mountains rise from the terraces in a series of ridges and valleys. The mine is at the foot of the Cascades. The tailings impoundment is in one of the steep valleys. The climate is mild and dry (Table 1). Site selection Twelve alternative sites within a 16-km (10-mile) radius of the mine were examined. Decision making theory was used to select the most suitable site. Advantages of the chosen site include its proximity to the mine and its low visibility from points of common public access. Also, the area was already heavily impacted by an existing silica quarry. The major disadvantage of the site is the need to pump tailings over a distance of 1.5 km (1 mile) and against a static head of 200 m (655 ft). Also, it is located in a gulch just upstream from the town of Wenatchee. Site geology The impoundment is generally underlain by interbedded sandstones and siltstones. The siltstones are often shattered. The sandstones are often friable. Both rock types are extensively jointed. Some isolated faulting of the sediments occurred before the area was covered with basalt flows. About 10,000 years ago, at the end of the ice age, the basalts were covered by 3 to 10 m (10 to 33 ft) of wind blown loess - a fine sandy clay and silt. River deposits filled the base of the valley to depths between 5 and 25 m (16 and 82 ft). Under the main part of the embankment, these materials were removed to expose bedrock. Ground water flow is generally through the more permeable layers. The permanent water table is about 5 m (16 ft) beneath the ground surface. Project and impoundment layout Figure 1 shows the layout of the mine, the mill, and the tailings impoundment. The tailings deliv-

Jan 8, 1986

By C. R. Hairfield

With ever rising energy costs, it is increasingly important for mines to operate with energy efficiency. As a large portion of a mine?s energy consumption is often attributed to the operation of mine ventilation fans, maintaining an efficient ventilation system is a critical pro-active way for mining companies to reduce power costs. A common way to measure a mine?s ventilation system efficiency is to calculate the volumetric efficiency, which is simply a calculation of the percentage of total mine air that is usefully employed for production. The purpose of this study is to document a nationwide comparison of the volumetric efficiency of U.S. underground coal mining operations. The results will aim to show just how efficient today?s coal mine ventilation systems are and what factors may be causing their various efficiencies and inefficiencies.

Jan 1, 2009

By Steve Kral

Not too many years ago, mining was in one of its cyclic down-sides. This forced mining companies into some innovative thinking to bring down the costs of production. And they have. Mining equipment and processing plants have become more efficient, mostly due to technological advances. The mining industry is now in a boom period, one that some analysts believe can sustain itself. But even with higher commodity prices, sky-rocketing energy costs and the costs associated with environmental and reclamation regulations have not allowed all mines to reach their full profitability potential.

Jan 1, 2006

Six pioneers of the American mining industry will be inducted into the National Mining Hall of Fame on Saturday, Sept. 13, at the Museum Convention Center in Leadville, CO. The 16th annual Mining Hall of Fame induction banquet will begin with a reception and open house at 5:30p.m., followed by the dinner and program at 7 p.m. The six inductees include James M. Gerstley, the only living member, and George O. Argall, Jr.; John F. “Leadville Johnny” Campion; Charles R. Nailler; Edwin N. Pennebaker and Russell L. Wood.

Jan 1, 2003

By M. Pawlik

The rheological properties of mineral suspensions affect the design and operation of transport, mixing, size classification, grinding, gravity concentration, flotation and de-watering systems. In many cases, the rheological properties can be modified to improve processing through the addition of chemical additives. These additives may be either organic or inorganic and generally affect the state of particle aggregation or dispersion. Inorganic modifiers act primarily by affecting the surface charge of mineral particles and thus control the magnitude of electrostatic attraction/repulsion between particles. The action of organic additives (polymers and surfactants) is a combination of electrostatic and steric forces – the latter being related to the molecular weight of these reagents. While low molecular weight polymers are dispersants (viscosity reducers), high molecular weight polymers are likely to induce flocculation and increase yield stress.

Jan 1, 2004

By S. Healey, P. Jean, G. Deschenes, M. Fulton

Three years ago, the New Britannia Mine started a project to improve productivity of its cyanidation plant. Results indicated that gold dissolution was strongly influenced by sulphide minerals and that the slower gold dissolution rate had a detrimental effect on overall gold recovery. The leaching strategy had to be modified to address this issue. Changes to the leaching circuit proved to be very successful. The first action was to introduce lead nitrate in the leaching circuit. The strategy of addition of lead nitrate was upgraded in three steps. An on-line free cyanide analyser was installed and the strategy of cyanide addition automated. The enhancement of the leaching kinetics have resulted: an 4% increase of gold recovery, from 87.8% in 1996 to 91.9% in 1999, which represents a reduction of 0.17 git Au in the leach residue; an average of 1330 additional extracted gold ounces per year from 1997 to 1999; a 21 % reduction in the cyanide consumption; the shut down of the cyanide destruction plant; and finally a contribution to the 27% reduction in the overall production cost per tonne of ore.($ 3 per ton). The significant increase of the throughput was instrumental in the reduction of the processing cost. In 1999, the improvement of gold recovery represented an additional gross revenue of $c""l.9 Million. The project is discussed in details in this paper.

Jan 1, 2000

By J. S. Peterson

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Jan 1, 1997

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice and the Australian VALMIN Code to a complex mineral property appraisal assignment. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others, and information and statements needed from the client. The exercise also highlighted many positive features of both documents. Some conflicts were found between the two documents. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed.

Jan 1, 2000

By M. J. Gregory

The Pebble Cu-Au-Mo deposit in southwest Alaska is one of the world's largest porphyry deposits. The western part of the deposit was discovered by Cominco America in 1987, who sold the project to Northern Dynasty Minerals Ltd., in 2001. Northern Dynasty discovered the high-grade eastern part of the deposit in 2004 and went into a 50:50 partnership with Anglo American PLC in 2007, forming the Pebble Limited Partnership (Lang et al., 2008). The Pebble Limited Partnership has continued to delineate the deposit through diamond drilling with the most recent resource estimate released in February 2010 (Pebble Limited Partnership, 2010). The Pebble deposit mineral resources comprise 5.94 billion tonnes of measured and indicated resources grading 0.78% Cu EQ, containing 55 billion pounds of copper, 67 million ounces of gold and 3.3 billion pounds of molybdenum. Also delineated are 4.84 billion tonnes of inferred mineral resources grading 0.53% Cu EQ, containing 25.6 billion pounds of copper, 40.4 million ounces of gold and 2.3 billion pounds of molybdenum (Pebble Limited Partnership, 2010). Resources are calculated using a 0.3% Cu EQ cutoff. GEOLOGY AND MINERALIZATION Deposit Geology The Pebble deposit is located in the Kahiltna terrane, between terminal strands of the north-east-striking Lake Clarke strike-slip fault. This fault represents an accretionary boundary and separates the Kahiltna terrane to the north-west from the Peninsular terrane to the south-east (Lang et al., 2008). The Pebble deposit represents a large magmatic-hydrothermal system centered on a group of 90 million year old porphyritic hornblende granodiorite intrusions. An east-west cross section through the southern part of the deposit (Figure 1A) shows the typical relationships between the various rock units which host sulfide mineralization. Sub-parallel ~96 million year old granodiorite and diorite sills were intruded into siltstones of the Jura-Cretaceous Kahiltna flysch. In the west, these sills were cut by a ~96 million year old alkalic intrusive complex composed of porphyritic monzonites and monzodiorites and related intrusion breccias (Bouley et al, 1995). The mineralized 90 million year old hornblende granodiorite intrusions cut all rock types and comprise four small stocks in the western part of the deposit and a larger pluton in the eastern part of the deposit. Recent deep drilling indicates that these intrusions coalesce at depth. The strongest porphyry-style mineralization is centered on the eastern granodiorite pluton and extends into the surrounding rock units (Figure 1A). The western half of the deposit crops out at surface, whereas the eastern side is un-conformably overlain by a cover sequence of Late Cretaceous to Eocene sedimentary and volcanic strata. The deposit was tilted 20º to the east during the Eocene.

Jan 1, 2012

By D. R. Wilburn

This summary of international mineral exploration activities for 2006 draws upon avail-able information from literature, industry and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review. They include budgetary statistics provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and information on regional and site-specific exploration activities that took place in 2006 compiled by the USGS.

Jan 1, 2007

By Gary Jackson

Preliminary engineering for the Waller Creek Tunnel was completed in 2001, but the project was held in abeyance until the summer of 2007. This paper describes several features of the revised design, which required significant changes from the original concept. Most notable is the expected replacement of a tunnel boring machine (TBM) by conventional tunneling. The considerable influence of geological conditions on the tunnel vertical alignment is discussed, in particular the impact of the zones of Eagle Ford Shale with swelling potential. Other features which are described include the wide span tunnels and large diameter shaft requirements.

By Robert M. Matyas, P. E. Sperry, Robert J. Smith, A. A. Mathews

INTRODUCTION The first Dispute Review Board (DRB) was utilized on a tunnel project 20 years ago. Increasingly utilized on a wide range of construction projects, DRB's are becoming the norm on tunnel and underground projects. This paper summarizes the growth in this usage, uses observations and experience to establish that barriers to the utilization of DRB's are more perceived than real and that many arguments against the DRB concept are not valid, and notes some of the salient elements that should be considered in practice to optimize DRB effectiveness. The purpose of the paper is to provide an annotated checklist for current and prospective users. The basic concept, structure, and operation of DRB's are described elsewhere and will not be repeated here (ASCE, 1991). DISPUTE REVIEW BOARD USAGE A compilation of Dispute Review Board usage for tunnel and underground projects to January 1994 indicated use on 63 contracts with a cumulative construction value of $3.8 billion and a total of 60 disputes settled. As of that same date, DRB's were planned for another 63 contracts with an estimated construction value of $4.7 billion. (A listing of these 126 projects is available from the authors.) This success and popularity have spread to other civil projects as well as process and building construction. The increase in DRB usage has been exponential. See Figure 1.

Jan 1, 1995

By E. V. Manlapig

This review paper describes recent advances that have been made at the Julius Kruttschnitt Mineral Research Centre (JKMRC) in Brisbane in developing a framework for simulating the flotation process. The work has been carried out collaboratively with the Mineral Processing Research Unit of the University of Cape Town in South Africa (UCT), as part of the Australian Minerals Industries Research Association (AMIRA) P9 Project. The framework consists of four components, namely – the mathematical model of the flotation process, suitable measurement tools for characterising the flotation cell, a computer program for modelling and simulating the process and the plantas for testing and validating the flotation models. A brief description of the model is first presented, then a number of applications of the model are described. The paper shows how the model can be used to optimise the performance of flotation cells, and then two case studies on the modelling methodologies are described. Finally the current and future plans of the project are outlined.

Jan 1, 2001

By J. B. Hedrick

In 2004, rare earths were not mined in the United States. The major supplier, Molycorp, continued to maintain a large stockpile of rare-earth concentrates and compounds. Major uses for these commodities were in automotive catalytic converters, petroleum fluid-cracking catalysts, permanent magnets, glass-polishing compounds, ceramics, metal-alloying additives, phosphors and rechargeable batteries. Consumption of refined rare-earth products decreased. The United States was a major importer and exporter of rare earths in 2004. Yttrium was not mined or refined in the United States in 2004. Imports from China, France and Japan accounted for most of the U.S. supply of yttrium compounds for refined yttrium products.

Jan 1, 2005

By W. Chae

The influence of solution ionic strength (IS) and electrolyte valence on the flotation behavior of malachite has been investigated. The microflotation tests were conducted over a range of solution IS (1?300 mM) at a constant speed (340 rpm), pH (9.5), flotation time (10 min), and sodium oleate dosage (5.3×10-7 moles/g). The size of malachite ranged from 45 to 53 µm, and two different types of electrolytes (NaCl and CaCl2) were employed. Electrophoretic mobility was also measured over the same IS range employed in the microflotation study. Overall, strong coupled effect of solution IS and ion valence was observed. Specifically, the flotability of malachite increased with increasing IS in the presence of monovalent cation (Na+) while the flotability increased up to 30 mM and decreased with increasing IS in the presence of divalent cation (Ca2+). Notably, the flotability of malachite was greater with the presence of Na+ compared with Ca2+ under high IS conditions (IS>30 mM). Consistent trend for Na+ versus Ca2+ was observed from the flotation results with different SO dosages. The characterization and flotation results suggested that the trend was likely attributed to the increased unfavorable interaction between malachite and bubble via the charge reversal of bubbles and malachite at higher IS in the presence of Ca2+.

Feb 27, 2013