Search Documents

By Lawrence A. Ph. D. Hansen, J. David Deatherage

Laboratory testing programs were conducted to investigate the performance under compression loading of several types of geomembranes and geotextiles proposed for use in heap and dump leach projects. Synthetic liners of several thicknesses were sandwiched between representative subgrade soils and cover materials, thus modeling in the laboratory the actual installation conditions expected. Performance was evaluated by visual inspection and vacuum testing. Several testing procedures and equipment were used to investigate the effect of these testing parameters on the predicted performance.

Jan 1, 1987

By Daniel P. Coughlin, Robert C. Thomas, Christopher S. Romanek, Kristian W. Paul

Two separate constructed treatment wetland (CTW) systems receiving the same metal contaminated, acid sulfate water over different lengths of time and at different rates were evaluated for metal attenuation. Both wetlands are the alkalinity generator portion of a succesive alkalinity producing system (SAPS). Sequential extractions are employed to determine phases of metal removal. Results indicate that Fe, Al, Zn, Ni. and Cu accumulate in the organic substrate over time. Manganese accumulates initially, but is not retained in the system over time.

Jan 1, 2000

By P. Venkatsubramanian, D. R. Maneval

An insufficient hydrologic data base exists for most large and small coal basins in Alaska owing to the lack of need in the past to collect data. The runoff process is insufficiently understood which is complicated by specifically northern phenomenon, and the lack of understanding of hydrologic relationships in permafrost environment. This paper presents an understanding of the hydrologic effects of frozen ground and presents methods by which the influence of surface mining upon the hydrologic balance can be analyzed.

Jan 1, 1987

By S. P. Lucido, I. Iwasaki

The potential of controlling heavy metal ions in effluents from discontinued mining operations and waste rock piles has been investigated. A fresh water green alga, Cyanidium caldarium, was found to have the potential to remove Cut' from solutions while exhibiting high tolerance to acid conditions which are commonly encountered in copper-nickel mine drainage. The process has the potential for application as a low maintenance metal decontamination system. The growth requirements and copper removal characteristics of this microorganism are described.

Jan 1, 1991

By William H. Meadows

This information describes the ventilating and methane gas testing procedures utilized during the raising of a mine shaft using a Robbins 81-R drill. An overview of the raise boring process is presented to illustrate the ventilating and gas testing procedures. A mine shaft project, 4.88 m (16 ft) in diameter and approximately 457.2 m (1500 ft) in length, will be the focal point of the presentation, with reference to similar projects for additional comments on variations in procedure.

Jan 1, 1980

By Tim Wolf

The author has seen an increased use of shaft-mounted, right angle drive assemblies. These designs use the pulley shaft as its 'foundation" and can create significant overhung loads. To reliably perform, the pulley and shaft must be designed for these special requirements. This paper will focus on the development of overhung loads and their design effects. Special considerations to maximize performance will be presented and comparisons with other drive options will be made. Experience in heavy mining applications will be used throughout.

Jan 1, 2000

By S. K. Kawatra, M. T. Rusesky, T. C. Eisele

An on-line monitoring system for apparent slurry viscosity has been developed at Michigan Technological University. It utilizes a vibrating sphere viscometer in conjunction with a special slurry presentation system to reduce particle settling and turbulence effects. It has proven to give accurate, reproducible results in an on-line hydrocyclone installation. Its performance shows that it can be an effective instrument on an industrial scale, particularly in grinding circuits. Development of the sensor and the importance of rheology in grinding are also discussed.

Jan 1, 1992

By G. G. O. O. Uwadiale

A number of Nigerian iron ore deposits have been upgraded to the specifications of concentrates for the blast furnace and the direct reduction iron- and steel-making plants. Depending on the mineralogy of the ore deposits, the techniques of oil agglomeration, magnetizing reduction, washing and scrubbing, gravity concentration, and reverse froth flotation have been utilized. A mode of distributive management of the deposits, in the direction of their technoeconomic utilization in the country's developing iron and steel plants, is presented.

Jan 1, 1990

Currently the challenge that our society faces is to combine the economic activity for the continuously increasing needs of our expanding population with the necessary environmental integrity and the humanistic social concerns. In this paper, the methodologies that should be applied by the progressive mining industry in order to fall within the frame of the sustainable development are summarized. The Sappes project, an advanced gold mining project in north-eastern Greece, is presented together with the approaches adopted by Thrace Minerals S.A.

Jan 1, 2003

By F. B. Micheli

Introduction and Historical Background Although both sluices and devices using a simple flowing film are among the oldest known methods of concentration, they are still extensively employed in a variety of situations where they are not only efficient but also have a low operating cost. More particularly, they are valuable for making a bulk concentrate of high specific gravity minerals from alluvials and beach sand and in upgrading low value ores. The antiquity of some of the basic concepts can be seen in the fact that they are found in Agricola's De Re Metallica which was published at Basic in 1546, while in 1602, Carew114 gave a fairly clear account of tin ore dressing in Cornwall in which grass turves were used to catch the cassiterite. This is perhaps one of the forerun¬ners of the blanket strake. The planilla of Mexico, the lanchute of Malaysia and the old Cornish box huddle are also descended from these early strakes. In fact, a sluice with holes in the bottom for concentrate discharge was shown by Agricola, not unlike the principle used in the plane table and the lamflo sluice. The convex huddle for the treatment of sandy material appeared about 1848 and the concave form eight to ten years later. For the treatment of "slime" sizes, wooden dead frames which were manually worked were used in Cornwall for many years but gave way to the automatic water-operated type in 1860, and even a mechanically tilted frame was described by Henderson115 in 1857. Theoretical Considerations The behavior of solid particles in suspension depends to a great extent upon the pulp density and the size of the suspended particles. In a fairly dilute suspension, such as that normally used when dealing with small particle sizes, the behavior of particles in a flowing film results from two effects. These are the lateral displacement, which is determined by the time taken for each particle to penetrate the flowing film and reach the solid surface, and the resistance offered by each particle to further displacement after it has reached this surface. The initial penetration through the flowing film depends on the size and specific gravity of the particle and the thickness and viscosity of the film. As a result the smaller particles will migrate further before their movement is retarded relative to larger particles of the same specific gravity. The behavior on reaching the solid surface de¬pends on whether there is a single particle layer or, as is more often the case, a multiple layer or thin bed of material which is sufficiently dilated, permits the penetration of higher specific gravity grains. Thrust of Flowing Films. When a thin film of liquid flows over a plane solid surface, the layer next to the surface remains at rest but the velocity of the film increases with the distance from the surface and becomes a maximum near, but not quite at, the free surface. Therefore, a particle in suspension in such a film is acted upon by a greater force near the upper part of the film than at the lower part, resulting in an overturning effect. After a particle reaches the separating surface or an accumulated densely packed bed of other particles, the liquid flow causes it to move downstream by rolling, sliding, or by a movement involving alternating suspension and deposi¬tion (saltation). In rolling and sliding, which are brought about by a substantially noneddying stream, the large submerged particles are acted upon to the greatest extent and they move more rapidly than smaller ones, notwithstanding their greater mass. When two particles of the same size but of different specific gravity are considered, the higher density one moves more slowly by reason of its greater mass. As a result the particles tend to become arranged in the manner shown in Fig. 29. If any particle is so large as to stand above the water surface, the transporting force on such a particle, although the maximum available, will have less effect than that on a submerged one. Such large grains are therefore carried a lesser distance. Fluid Velocity in a Flowing Film It can be shown that if y is the distance within the flowing film from the interface, the fluid velocity v' at this point is given by IIn this equation p' is the fluid density, g the acceleration due to gravity, a the viscosity, a the angle made by the film to the horizontal, and 0 the film thickness (in cgs units). Furthermore, the volume Q of fluid per unit time and unit width is related to the film thickness and can be calculated, since which upon integration gives Consideration of the velocity v' (Eq. l) and the terminal falling velocity µ derived from Stokes law enables the horizontal travel dz in time dt to be calculated as follows: Again integration and substitution of Eq. 3 gives In this equation, z is the distance travelled before a particle of density p at the top of the fluid film has settled on the concentrating surface. From these expressions it can be seen that the depth of the flowing film varies as the cube root of the volume of fluid and inversely as the cube root of the sine of the plane surface inclination. Similarly the distance a particle can travel before reaching the surface is directly related to the quantity of fluid and its viscosity. The viscosity of pulp is greatly increased by the presence of near colloidal particles and consequently the penetration of the somewhat larger grains through the flowing film is retarded, resulting in them being carried further across the concentrator deck. Obviously this effect can be reduced by prior removal of some or all of the ultra¬fine particles. The detrimental effect of kaolin on the separation of fine ferrosilicon from quartz has also been demonstrated by Johnston,116 the relationship between viscosity and efficiency of separation being shown in Fig. 30. The pH value also has a very marked influence on the viscosity and the use of acid mine water, for example, can increase viscosity materially and thereby result in lower efficiency. Dilation of Multi-Particle Systems Except during washing (when a single particle layer may exist) concentration usually takes place in a bed of particles which is partially dilated or stirred by eddy currents. The extreme case is seen in various forms of the sluice where the flow of water and the presence of riffles combine to create a fluid bed in which reverse classification takes

Jan 1, 1985

By Nathaniel Herz, R. J. Adamson, C. M. Romanowitz, Frank W. Jr. McQuiston, C. D. Hoyt, Robert S. Shoemaker, P. H. O’Neil

1. INTRODUCTION In this section, precious metals are defined as gold, silver, and the platinum group metals comprised of platinum, palladium, iridium, osmium, and rhodium. If the first three years of the 1970's are the criteria, gold, silver, and platinum seem destined for a bright future. Gold advanced in price from the historic figure of $35 established in 1934 to over $100 per oz (1973). For the five years 1966 to 1970, silver consumption exceeded production by about 50%. The silver price appears to be definitely on the uptrend, and a price of over $3 per oz seems probable. On this basis (at 1964 costs) the United States has an estimated 5 billion oz of unmined silver. The fresh burst of interest in platinum with a surge of renewed price strength (end of 1972) is due to the activity in the automobile emission control area, where platinum re¬mains the front runner in the catalyst area. Some international financial experts believe that governments will not rush into reform of the monetary system, and "Special Drawing Rights" (SDR's) will gain increased standing as international mone¬tary reserve assets. Gold will continue to be reviewed as the ultimate store of value and will remain the global monetary base. Devaluation of the U.S. dollar caused by imbalance of import payments over ex¬ports is the basic reason that the price of gold will likely remain above the $90 per oz figure for the balance of the 1970's. Gold and silver usually occur intimately associated, and recovery methods are often closely related; however, they were assigned sepa¬rate chapters, because the major production of each metal is from ore deposits classified as either gold or silver. For example, the gold ore occurrences in South Africa, the world's leading gold producer, have a ratio of gold to silver of approximately 10 to 1. The ores at the Homestake Mine, Lead, S.D., the largest U.S. gold producer, are predominantly gold with a ratio to silver of approximately 5 to 1. Silver in each example is a byproduct. By this same classification, the largest U.S. silver producers are the silver ores of the Sunshine, Galena, and Lucky Friday mines in the Coeur d'Alene district, Idaho. However, the largest single-mine silver producer in the Free World is the Kidd Creek Mine at Timmins, Ont., where the occurrence is with sulfides of copper, lead, and zinc. Thus, the major gold production of the world is derived from those ores classified as gold ores; whereas, less than one-half of the silver production is from silver ores, and only a small percentage of the silver production is from gold ores. 2. GOLD Gold, the noblest of metals, has been mined for thousands of years. Its chemical symbol, Au, is derived from the Latin "aurum," meaning "shining dawn." A precious substance because it is one of the rarest metals, it has unique physical properties: it does not tarnish; it exceeds all other metals or alloys in malleability and ductility; it is a good conductor of electricity and is one of the most nonreactive metals. Its greatest strength is its indestructibility. It is the only metal mined at depths exceeding 10,000 ft. Since the early 1800s, its chief role has been as a medium of exchange, providing the basis for interna¬tional trade. In the past 15 years, however, gold has emerged as a useful industrial commodity. This role has been fortified by the estab¬lishment of a two-tier pricing system which maintains monetary gold prices at an established U.S. Government price, with industrial gold being priced higher by the free-market system. Occurrences and Production Native gold furnishes most of the world's production, since gold forms stable natural compounds with few other elements. Neverthe¬less, the metal is widespread with traces of it found in seawater and in the ashes of plants and animal material. Next to the native metal, the tellurides have been the most important gold-bearing minerals; these include calaverite, krennerite, slyvanite, hessite, and nagyagite. Native gold is invariably alloyed with more or less silver, but it is exceptional to find any other metal in the alloy. It is found in veins associated with quartz, calcite, alunite, other gangue minerals, and with various sulfides. Sulfide minerals in order of frequent associa¬tion are: pyrite, galena, chalcopyrite, sphalerite, arsenopyrite, tetrahe¬drite, and pyrrhotite. Small amounts of metallic gold are commonly disseminated through such sulfides. When considerable amounts of silver occur in gold, the mineral electrum is formed. In a few deposits, gold and mercury form natural amalgam. Native mercury is formed by weathering from cinnabar and other mercury minerals. Among the minerals sometimes mistaken for gold, pyrite, marcasite, and especially chalcopyrite may be men¬tioned. The flakes of biotite and other micas, especially when partially oxidized, also may imitate it closely. World gold reserves never have been estimated carefully. Esti¬mates indicate that present world reserves approximate I billion oz, of which about 60% occurs in South Africa and 20% in the USSR. World gold output is dominated by South Africa which produces two-thirds of the world's production from reserves that are adequate to maintain existing output levels. South African gold output comes from approximately 50 large underground operations that mine and mill 70 to 80 million tons of ore annually to recover 30 to 32 million oz of gold. The USSR is the second largest gold producer, followed by Canada and the United States (see Table 1). Gold production in the United States and Canada rose to high levels in the 1930's, following the increase in price from $20.67 to $35 per oz and with an abundance of good labor due to depression in other industries. Production of over 10 million oz in 1940 was behind only that of South Africa. World War II caused a precipitous drop in gold output due to the imposition of War Production Board Limitation Order L-208 issued in October 1942, which caused over 9,000 gold mines in the United States to shut down, most of which never reopened. The U.S. Treasury, which suspended purchases of newly mined gold in 1968, had been the sole buyer of U.S. produced gold since 1934. This created the two-tier pricing system, and in March 1972 the President signed into law a bill authorizing a $3 increase in the official price of gold to $38 per oz. In February 1973 the President ordered a second devaluation of the dollar, amounting to about 10% which raised the official price to $42.22 per oz. The erratic development of the gold market, which has seen the

Jan 1, 1985

By R. A. Metz, William H. Breeding

The remarks that follow are based substantially on experience covering 45 years, 80% of which has been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1-1/2%. The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present. Most of the rich, readily accessible placers were mined by our forefathers. Current opportunities exist: (1) in remote areas where infrastructure has been absent in the past, or development has been prohibited by adverse ownership - political or commercial; (2) in deposits that could not be mined by equipment available to our forefathers; (3) in deposits unidentified by our forefathers; (4) where the-price-of-product/cost ratio is substantially better than in earlier years; or (5) a combination of those factors. When I entered the placer business in the late 1930s, and subsequently, a prevailing opinion believed that glacial deposits should be avoided as irregular in mineral content and composition, and unrewarding to explore and develop; yet an operator has been mining a fluvio-glacial deposit profitably for the past 17 years. Rich buried placer channels, often called paleo-channels were worked in the last century, generally by hand methods, and under conditions that would be unacceptable today. Exploration and mining equipment now available make some of these channels attractive targets. Well-known examples are in California and Australia. The formation of a commercial placer requires a source of valuable minerals. Above primary deposits, there may be eluvial deposits formed by the erosion of gangue minerals and the concentration "in situ" of valuable minerals. Down slope from these deposits are the hillside or colluvial deposits, and below them are the alluvial deposits of redeposited material. Most of the great placer fields of the world are the result of several generations of erosion and deposition. Well-known examples are in California and Colombia. Gold is a very resistant and malleable material, and gold placers may extend for 64 or 80 km (40 or 50 miles) along a river system. Platinum is less malleable, but is very resistant to disintegration. Diamonds are extremely hard, and (especially gem diamonds) may be found over great lengths of a river system. Cassiterite is less resistant to disintegration, and tin placers seldom extend over two miles without resupply from an additional source or sources of mineralizaton. Tungsten minerals are generally more friable, and within a few hundred yards of the source disintegrate to the point that they are uneconomical to recover. Rutile, ilmenite and zircon placers generally result from the weathering of massive deposits, and may be encountered over extensive areas; most are fine grained and durable. What does a geologist or mining engineer look for in placer exploration? The old adage to look for a mine near an existing mine is still valid. You need a source of valuable mineral. Then you require conditions for concentration, which means a satisfactory gradient and/or other conditions that will permit heavy minerals to settle. Nicely riffled gravel, often called a shingling of the bars, is conducive to placer formation. Coarser gravel is logically associated with coarser gold. Excessive clay and/or high stream velocities in narrow channels can carry gold far downstream and distribute it uncommercially over a large area. When material is extremely fine, in situ weathering and concentration become more important. Placers frequently occur distant from lode mines, and one must remember that in a larger watershed the exceptional floods that occur once in a hundred or a thousand years can move great quantities of material long distances. The carrying power of water is said to vary with the fifth or sixth power of its velocity. I am not ready to disagree with Waldemar Lindgren and accept that many commercial placers are substantially enriched by the chemical deposition of gold from solutions; however, I have seen crystalline gold in clayey material quite distant from known sources of primary gold that is dif-

Jan 1, 1992

By Bobby C. Carson

INTRODUCTION The National Park Service is entering the seventh year of monitoring caves for the presence of radon and radon daughter products. The purpose of this paper is to summarize the radiation monitoring program at Mammoth Cave National Park, and to present some of the results of this program. Mammoth Cave National Park completed five years of collecting data on May 1, 1981: although Mammoth Cave encompasses approximately 361 km of underground passageways, this paper will concentrate on only a 2.2 km section of the cave known as the Historic Tour. Included in this paper is a discussion of the methods the Nations Park Service uses to protect employees from exposure to alpha radiation. MONITORING METHODS The National Park Service monitors cave atmospheres utilizing the procedures provided by the Mine Safety and Health Administration in their Radiation Monitoring Training Manual (Anon., 1976). This procedure is described as the Kusnetz Method (Kusnetz, 1956) of radon daughter monitoring. Due to the length of the tours at Mammoth Cave, it has been determined to be the most practical procedure. The Historic Tour is a 2.2 km (1.4 mile) loop through passageways ranging in size from 18 m high by 12 m wide, to 0.9 m high by 0.6 m wide. Seven five minute walking samples were taken for this cave tour by drawing at least 10 1 of air through a 25 mm fiberglass filter utilizing a Monitaire Sampler Pump. The radon daughter concentration levels were determined using an alpha scintillation counter to measure the alpha activity on the filter paper. The Monitaire Sampler Pump was calibrated each day prior to monitoring the cave tour and the scintillation counter was calibrated by procedures described by the Mine Safety and Health Administration (Beckman, 1975) at six month intervals. Guidelines established by the National Park Service and approved by the Mine Safety and Health Administration require weekly sampling when the average working level exceeds 0.30 (NPS-14, 1980). A working level is an atmospheric concentration of radon (Rn-222) daughters which will deliver 1.3 x 10 5 MeV of alpha energy per liter of air in decaying through Ra C' (Po-214). The Historic Tour has continually exceeded the 0.30 working level average and has been monitored weekly. Generally, only radon daughter working level data has been collected on the Historic Tour due to limited personnel. However, other special measurements of the uncombined fractions of radon daughters with wire screens, tsivoglou method for radon daughter sampling (Thomas modification, 1970), and thoron daughter monitoring. These special measurements have not been routine due to time limitations involved in radon daughter sampling of other occupied portions of the cave. SUMMARY OF DATA The Historic Tour has been the most consistantly monitored tour since elevated levels of alpha radiation were found to exist at Mammoth. Cave. It is also the only natural entrance to the main sections of the cave and provided an opportunity to study man made actions upon the natural entrance. For these reasons the Historic Tour was isolated for study. Beginning October 10, 1977, and ending November 20, 1977, a pilot project was undertaken involving the Historic Tour and the practice of covering the natural entrance to this tour with sheet metal in the winter months. The purpose was to study radiation levels on the Historice Tour while the covers were on and off the natural entrance. In this pilot project, comparisons were made with incast air with covers on and off the entrance, and outcast air with covers on and off the entrance. TABLE 1 Incast air Mean W.L. Covers on . . . . 1.46 W.L. Increased 54% Covers off. . . . 0.67 W.L. when covers on Outcast air Mean W.L. Covers on . . . . 1.33 W.L. Decreased 5% Covers off. . . . 1.40 W.L. when covers on The natural entrance was artificially covered in the winter months (Yarborough, 1978) to protect the visitor from the extremely cold incast air, in the first four years of monitoring. The data in Table 1, illustrated in Figures 1 and 2, shows that this action increased the radon daughter working levels on the Historic Tour by 54% when the covers were on the entrance and the airflow was incast. While the air flow was outcast at the natural entrance, it made little difference as to whether the entrance was closed or open. Some interesting findings were observed when

Jan 1, 1981

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

4.1 THE GENERAL COMPOSITION AND PROPERTIES OF CLAY-BASED GROUTS Clay-based grouts are visco-plastic systems; they are made by adding structure-forming reagents to a clay mineral mortar. Small amounts of cement and various chemical ad¬ditives constitute the reagents. If necessary, fillers also are added. The distinguishing feature of clay-based grouts is that throughout their entire stabilization period they do not form a crystallized structure as does cement grout. The structure of stabilized clay-based grouts does not deteriorate during minor rock movement or upon the initiation of blast¬ing during the construction of a shaft or a drift. Because they can possess good rheological properties during the ini¬tial structure-forming period relative to cement grouts, clay¬based grouts are not easily eroded from large fractures and karstic cavities by flowing ground water. In addition, their finely dispersed clay particles facilitate a greater fracture penetration capacity, especially in dual porosity rocks. Numerous investigations of the structural-mechanical and rheological properties of clay-based grouts by STG have demonstrated that the most effective grouts for pre¬venting the inflow of ground water into underground work¬ings are grouts that have a cement content of 8 to 10% (90 to 120 kg/m3) of the clay grout by mass. The grout should have a density of 1.18 to 1.30 T/m3. Various additional substances and chemicals can be added as additional fillers and structure-forming reagents. In pure ground water at temperatures above freezing, sodium silicate in the amount of 0.8 to 1 % by mass normally is the only structure-forming reagent that is necessary if the proper clay is selected and if it is available. The production process for making clay-based grout is divided into two stages: 1) the production of an initial clay mortar with specified properties and 2) the production of a clay-cement additive grout mixture using the initial grout along with the structure-forming reagents, including the ce¬ment. The properties of clay-based grouts depend on the phys¬ical-mechanical properties of the initial clay mineral, the properties of the cement and the properties of the chemical reagents that are added. 4.1.1 TECHNOLOGICAL PROPERTIES OF CLAY-BASED GROUTS The dynamic shear stress' To, the viscosity 11, the static shear stress2 0, the maximum shear stress of the structured that the rheological and structural-mechanical prop¬erties of clay-based grouts must fall within the following limits: the dynamic shear stress To = 50 to 200 Pa; the viscosity -9 = 0.02 to 0.07 Pa sec; the static shear stress 0 = 150 to 600 Pa; the plasticity strength Pm of the structure one minute after preparation (according to P.A. Rebinder's method) equals 150 to 500 Pa. The plasticity strength 10 days after preparation is ? 0.15 MPa. The general relationship of the change in the structural strength of clay-based grouts relative to stabilization time is shown in Fig. 32. The figure shows that the structure-form¬ing process for clay-based grouts is characterized by three stages. These stages correspond to the time periods required for conducting the principal operations during the injection of the grout into a fractured aquifer as described below. Stage I, corresponding to the time period T1, reflects the small development of structural strength during early stabi¬lization. During this time, the structural strength must not preclude the capability to pump the grout. The time Tl must correspond to the length of pumping time from the moment water is shut off and mixing occurs until the pump stops forcing the grout through the manifold block and pipeline into the fractured rock as described subsequently herein. Stage II, corresponding to the time interval T2, reflects a sharp but controllable increase in the structural strength of the grout. The length of time period T2 is controlled by the addition of appropriate reagents. Stage III produces the final value of the structural strength. This final strength is used to design the dimensions of the isolation curtain. Consequently, the development of grouts is guided by two principal criteria: 1) the grout must develop the highest possible structural-mechanical properties and 2) it must be able to be pumped by a piston pump prior to final stabili¬zation. Successful grouting depends to a large extent on the correct design of a grout for each specific case. It is impor-

Jan 1, 1993

By Eleanor Kentish, Edward Batty, Alan Skarda

"The design of the tunnels at Bond Street Station includes a final sprayed concrete fireproofing layer. The performance of this layer was verified by a program of testing to Crossrail’s KT24 specification, which proved that a dosage of 1kg/m³ polypropylene fibers and a layer thickness of 50mm would be sufficient to limit spalling in the event of a fire. Application of this thin layer was achieved using a state of the art spraying robot, with the ability to scan the profile and automatically apply a uniform layer of concrete. To provide assurance and calibrate this spraying robot, BFK developed a bespoke survey system for checking SCL thicknesses in the field. This provided an instant independent check of the spraying robot and allowed areas of inadequate thickness to be rectified without risk of cold joints. This paper describes the practical application of the fireproofing layer and how design compliance was ensured. INTRODUCTION Fire is one of the most serious risks to a tunnel. The nature of tunnels — being long enclosed spaces — can increase the intensity of a fire, and make fire-fighting and rescue operations difficult. The damage that can be caused has been demonstrated by a number of historic tunnel fires, such as the Channel Tunnel fires of 1996 and 2008, and the Mont Blanc Tunnel fire in 1999. Without any intervention, the high temperatures in a fire create thermal stresses and a build-up of vapor pressure within the pores of concrete, which eventually exceed the tensile strength and trigger explosive spalling. Spalling exposes the core of the section to severe temperatures, leading to a loss of concrete and steel reinforcement strength or further spalling of successive layers. The concrete used in tunnel linings is particularly susceptible to explosive spalling, due to its low permeability achieved by the addition of microsilica (Bailey 2011). The sprayed concrete lined (SCL) tunnels on Crossrail have been designed to resist the worst anticipated fire in operation, in order to prevent collapse and minimize damage to the structure. The design called for a system of passive fire protection, the efficacy of which was validated by the contractor through a testing regime. It was critical that the application on site reflected the test conditions, which demanded special control of the profile and thickness of the lining. In order to meet these constraints on tolerances and quality, BAM Ferrovial Kier joint venture (BFK) developed a reliable method of working with the Meyco Logica spraying robot, and a bespoke survey system for accurately checking thicknesses in the field. These innovations are the focus of this paper."

Jan 1, 2016

By Lawrence M. Brennan

Early in 1971 the Peabody Design and Preparation group began engineering on a preparation plant which was to process eight mil- lion tons per year of raw coal. For the first five or six years this product was to be furnished 50% from surface mining operations and roughly 50% from underground operations. By early 1980, 1008 of the production was to come from underground mines. Because of the large annual commitment from Randolph Preparation Plant, it was essential that the plant operate with minimum down-time. As usual, capital costs were to be kept at a minimum. Before we discuss the details of design, it would be best to discuss the overall picture. Underground production to be pro- cessed through Randolph Preparation Plant was to be delivered by means of one mile overland conveyor from Baldwin #1 Underground Mine to the plant. Surface Mine production was to be delivered by means of 100-ton haulage units dumping in a 1,000-ton capacity hopper. Because of the changing production rates in both the underground and surface mines as well as the great difference in size consist, it was decided that it would be necessary to divorce the plant as much as possible from production. For this reason, twin 6,500-ton raw coal silos were constructed to separate the two coals as well as allow blending. The preparation plant itself, was to be designed to Operate two shifts per day, five days per week, at an average rate Of 2,200 tons per hour with a maximum rate of 2600 to 2800 tons per hour. Coal was to be delivered to our customers by means of rail haulage at both unit train rates and plant process rates. The surface mined coal, after discharging into the 1,000-ton R.O.M. hopper, is fed by means of two 72" wide reciprocating feeders onto a 72" wide steel cable belt. The steel cabled conveyor discharges the R.O.M. coal onto a fixed grizzly, scalping out a percent of the 6 x 0 coal. The balance is fed to a 12' x 27' Rotary Breaker. The material passing through 6" round hole screens is added to the 6" x 0" from the scalping screen. The 6" x 0" is conveyed to the top of one of the 6500 ton silos designated for surface coal. Material that is not broken to pass the 6" breaker screen is discharged to a bin and disposed of with plant refuse.

Jan 1, 1976

By J. Roufagalas

Sustainable development requires that exploitation of environmental resources is such that it does not result in permanent damage to the environment. In many instances environmental damage is an external cost of the entity exploiting the resource. Ideally, the entity should be forced to internalize this cost. Various financial assurance schemes have been proposed to ensure that the entities fulfill their financial responsibility to restore the environmental dam-age. Prominent among these schemes are ?environmental bonding requirements?. A main issue with these financial assurance schemes is that many times the amount and duration of environmental damage is uncertain. That is, the cost of restoring the environment in the future may be unknown (or unknowable), and, furthermore, the extent of the damage may not be known for many years into the future. Nevertheless, bonding requirements have to be set in advance and the rules for returning the bond and absolving the entity of responsibility have to be specified ex ante. In practice, a problem of allocation of resources arises. To make sure that all external costs are internalized, in the face of uncertainty, will require a sufficiently (arbitrarily) large bond for a sufficiently (arbitrarily) long period of time. But such a requirement may prove too expensive and may result in not undertaking a project (even if, under certainty, the project may be profitable after internalizing all costs). This will result in a reduction in total welfare. Under present bonding requirements, firms are responsible up to the value of the bond. This results in an asymmetry: if environmental restoration is less than the bond amount, the firm has an incentive to restore and reclaim the bond; if the cost of the environmental restoration is above the value of the bond, the incentive is to forfeit the bond, imposing on the government/ society the excess cost. This also may reduce social welfare, at least on distributional grounds since the firm owners pocket the profits and the taxpayers foot the bill. The presence of uncertainty suggests that a fee based reclamation fund may be welfare enhancing. The thinking can be sketched as follows: All firms undertaking environmentally sensitive projects pay into the proposed fund. The fund examines the risks and sets the premiums at the level of the expected restoration costs (not the maximum!) plus administrative expenses. One advantage of the scheme is that this eliminates the asymmetry. Firms with restoration costs below expected end up subsidizing firms whose restoration costs were underestimated. In other words, the industry ends up internalizing the costs not internalized by the individual firms, instead of the taxpayers.

Jan 1, 2007

The Mine Safety and Health Administration (MSHA) academy in Beckley, WV, received enquiries from various segments of the mining industry concerning alcohol and substance abuse in the mining industry. The MSHA Director formed a committee, the Mining Industry Committee on Substance Abuse (MICSA), to deal with these enquiries. The committee met in April 1985 at the mining academy in Beckley. The MICSA committee expanded its membership to represent labor, management, and government agencies affiliated with the mining industry as well as government agencies dealing with alcohol and drug abuse. This expanded 18-member committee met for the first time in July 1985. At that time, two cochairmen were elected, one from labor and one from management. MICSA has spent time on education by sharing information on the issues and by calling in outside experts for advice and consultation. The committee also initiated several projects. These include a resource manual on substance abuse and employee assistance programs. Mine operators and labor unions can use these programs as guides. MICSA is also assembling statistics on substance abuse, particularly as applied to mining. And the committee commissioned an Education film, Substance Abuse, Is It Our Problem? (The results of a survey on drug use, given in Table 1, suggest that substance abuse may indeed be a problem.) The educational film, produced by MSHA, is an introduction to the problem of substance abuse in the mining environment. The film encourages mine operators, labor unions, and miners to analyze their individual circumstances to determine whether a problem exists. The film also offers ways to deal with the problem. And the film invites the mining industry to request additional information from MICSA. There is no single approach to substance abuse that will fit the need of every mining operation. As with any health, safety, or production problem, remedies must be site specific. MICSA's aim is to channel ideas to those who seek to help employees in a mining environment who seek to rid themselves of alcohol and substance abuse. As stated more formally: The Mining Industry Committee on Substance Abuse represents the efforts of labor, management, and government. The mission of the committee is to make the mining industry aware of the problems resulting from alcohol and other drug abuse and to recommend possible methods to remedy the problem. The function of the committee is to assist the industry in developing programs and resources to recognize and provide help for troubled employees, and thus reduce the risk of accidents, while lower absenteeism and increasing productivity.

Jan 11, 1987

By James L. Hendrix, David Castillo

Cyanidation is one of the most common practices used in the extraction of gold and silver. One method of application is heap or dump leaching which entails the leaching of the gold or silver ore by spraying or dripping a cyanide lixiviant over the ore and collecting the effluent. The ore is placed on what is known as a leach pad system. A typical leach pad system consists of a foundation, a leakaqe detection system, a liner, and a cover layer (Strachan and van Zyl, 1988). There are many types of liners available for use. The type of liner depends upon what type leaching pad system us used. Generally, leaching pad systems can be categorized into two types: an expandable pad and a reusable pad. An expandable pad exposes the liner to the elements only in the initial stages of ore placement on the leach pad system. A reusable pad exposes the liner to the elements on a periodic basis. In addition to the exposure to the elements, the liner is also under the stress of the ore placed on it and the stress of the vehicular traffic across it. These stresses and exposure to the elements are the major causes of liner failures, which can appear as punctures, tears, cracks, and deterioration. Because of the possibility of the failure of the pads to contain cyanide-laden solutions the designs for liners of pads and ponds have become more and more stringent. Currently, though, there is some recognition that in some locales such stringent design criteria may not be required (Chatwin, 1989). Some soils have significant cyanide attenuation and degradation capacity. It has been found that soils containing carbon- aceous materia1 wi11 remove cyanide from solutions percolating through them (Chatwin, 1989). Of course metallurgists have long recognized the deleterious effect of carbonaceous material in the mill circuit. Sheridan, et a1 (1988) have shown that WAD cyanide is detected in the effluent of a 2 m column filled with ground carbonaceous ore only after it had been continuously washed with greater than 9 pore volumes of NaCN solution. It was decided to examine the potential of successfully attenuating cyanide by placing an organic material layer between a 1iner and the prepared soil base. One consideration for the selection of the organic material was cost. Sawmill wastes, ground agricultural wastes (such as corn cobs), and other organic wastes were considered. But the first waste to be tested was a product found at any metropolitan area, sewage sludge.

Jan 1, 1990

By Peter W. Scott

Feldspars have major uses in glass manufacture and in ceramic products. About 6 million metric tons (6.6 million short tons) are used annually. Feldspars are desirable because of their high aluminum and alkali contents. Na feldspars are favored for glass, while K feldspar is often preferred in the pottery and tile industries. Economic deposits occur in a variety of geological environments. Most are in granites or granite-like bodies, pegmatites being a common source worldwide. Alkali granites, particularly those some- times called alaskites, are mined directly as a source of feldspar and associated minerals. Some other igneous bodies, such as aplites, rhyolites, and partly altered granites (for example china stone) provide alternative feldspar-rich products. Nepheline syenites and phonolites are other sources of feldspar and contain higher amounts of alkalis. Feldspar-rich (arkosic) sediments derived from the weathering of pegmatites and granites are widely extracted and processed for use in ceramics. The present study reviewed the various sources of feldspars throughout the world. Data on the quality of products has been taken from literature, and samples have been obtained from a large number of producers. The mineralogy and chemistry of the samples has been determined and, as far as possible, have been related to the geology of the source area. Feldspar products show a wide range of chemical and mineralogical compositions. Some are pure Na feldspar (albite), others are made up entirely of K feldspar (microline and orthoclase), but many are mixtures of Na and K feldspars. Significant quantities of quartz are often present, and many products contain mica and kaolinite. Fe203 con- tents are very low, typically less than 0.1 percent. Detailed mineralogical studies show that four groups of products can be recognized on the basis of feldspar mineralogy. These are albite, albite with microcline, microcline with orthoclase, and orthoclase with albite. Products containing microcline and orthoclase together are mostly sedimentary in origin. Those with albite only, or albite with microcline have a pegmatitic or granite origin. Those containing orthoclase as the dominant K feldspar are derived from aplites or rhyolites. There does not appear to be any relationship between the feldspar mineralogy and the quartz content. Peraluminous S- type granites and pelite-dominated high-grade metamorphic rocks, in which there is a significant volatile component, are likely to be the most important feldspar sources. Partial kaolinization of feldspar-containing rocks often improves minability, decreases crushing costs, reduces iron content, and increases the K2O/Na2O ratio.

Jan 1, 2001