Search Documents

By M. G. Skowroski, G. G. Eichholz, J. P. Ambrose

Introduction It has long been known that there are extensive deposits of phosphate-bearing deposits in the Coastal Plain of Georgia in many locations that are similar to those being mined commercially in central Florida. A major drilling program was conducted in 1966-67 by the Georgia Geological Survey (GGS). The economic potential of some of the material uncovered was evaluated at that time by a team at Georgia Institute of Technology led by Dr. J.E. Husted. There were some promising results. Since then, there has been little commercial interest in pursuing this matter, though the potential for development remains. In the long term, Georgia's phosphorite deposits could be a major source of income to the state if they were commercially processed. Phosphorite deposits contain significant levels of uranium and thorium. Uranium concentrations in Florida phosphate aggregates have been found to be 120 to 140 ppm. The presence of high concentrations of uranium means that there is a small but finite concentration of radium, which subsequently leads to radon gas emanation. It is the radon emanation and its progeny that may pose the largest health problem in many types of mining. Surface mining operations can possibly elevate the radon and radon daughter concentration in the vicinity. There is always some public concern whether any increase in the radon concentration in the atmosphere by mining (surface mining in the phosphorite case) could elevate the risk of cancer in the nearby population. At the present time, a great deal of attention has been devoted to the possible health effects of radon and its decay products in the inhaled air in mines and inside buildings built on mill tailings or uranium-bearing rock (Gesell and Lowder, 1980). Several evaluations have been published on the potential health effects of the Florida phosphate operations (Guimond and Windham, 1975; Roessler et al., 1980; Travis et al., 1979) and for buildings incorporating phosphate slag aggregates (Kahn, Eichholz, and Clarke, 1983; Roessler, Roessler, and Bolch, 1983). They all indicate that such potential effects are small, but tangible, compared with other radiation effects, for instance in the nuclear industry (Cohen, 1981). In view of the current concern, especially by the US Environmental Protection Agency (EPA), with the radiological consequences of large-scale mining of uranium-bearing phosphate rock (Guimond and Windham, 1975), it was decided to assess the potential radiological consequences if the Georgia deposits were developed. This paper presents an attempt to estimate the magnitude of any radon-based health effects that might arise from future mining operations in selected areas of the Georgia coastal region. To do this, a calculational model was developed that took into account the mining operations themselves, the atmospheric dispersion of the radon released, and the radon daughter concentrations in nearby towns. The model was applied to both extremes. The first application was a hypothetical mining operation in Echols County. Echols County is very sparsely populated and, unless living very close to the site, a person would probably experience little radiation exposure, if any. The model tries to prove this point. The second application was at a site near Savannah, Georgia. Both sites contain economically feasible phosphorite deposits and were not entirely hypothetical in that sense. Site selection In the course of the South Georgia Minerals Program (Furcron, 1967), an extensive series of drill core samples had been collected from various mineral occurrences in the coastal plain. It was found that the cores from the previous drilling program (Furcron, 1967), though carefully preserved, were not readily accessible. But the GGS reports did contain gamma logs of all the holes surveyed. With the cooperation of Dr. Neal Shapiro of the Survey, some core samples were selected and assayed, and used to calibrate the gamma log data. Samples from locations known to have detectable radioactivity were screened and counted. Their measured uranium content was used to calibrate the gamma log profiles for those same holes as obtained by the GGS. On this basis, two of the higher-level sites were selected and the calibration was used to obtain integrated uranium concentrations over the length of the borehole. It is customary to describe radon and radon-daughter concentrations in "working levels" (WL), where one WL represents a concentration of radon daughters capable of releasing 130 000 MeV of alpha particles, equivalent to 100 pCi of radon in equilibrium with its daughters per liter of air. A representative concentration is 0.15 WL, below which radon levels are widely considered to be negligible. For the mine sites selected, the surface area and rock volume were determined to estimate their radon content. Working-level values were then estimated for the assumed radon release from the crushed ore and the exposed surfaces of the mine pit. According to Kisielewski (1980), 93.4% of all radon released from open-pit operations is released from the ore zone; thus, the calculations assumed that those surface areas were the main sources.

Jan 1, 1987

By B. Mather

I was very glad to see an article on alkali-silica reactivity of concrete aggregate in Mining Engineering. It is a topic that should be reexamined every 45 or 50 years. The last paper (that I am aware of) that examined this topic in Mining Engineering was Rexford (1950), who, at the time, was chief of the Petrography Section, South Pacific Division Laboratory, Corps of Engineers, Los Angeles, CA. The paper was presented at the AIME meeting in Los Angeles in October 1948. Professor Leming's discussion generally reflects the current state-of-the-art; but it provides no references for more detailed information. I wrote a paper titled "How to avoid excessive expansion of concrete due to alkali-aggregate reaction," which was included in the Proceedings of the Second International Conference on Alkali-Aggregate Reactions in Hydroelectric Plants and Dams (Mather, 1995). In it, I emphasized that it was the hydroxide ion (not the alkali ion) that caused the pore fluid in the concrete to dissolve reactive silica, producing alkali-silica gel capable of taking up water, thereby, causing swelling and rupturing of the concrete. Excessive expansion will not occur unless there is a sufficient amount of potentially expansive alkali-silica reaction product and water. However, this will not occur unless there is a sufficient quantity of reactive aggregate and unless there is a mechanism by which the pH of the pore fluid can get well above the normal value of about 12.6. In many cases it is sufficient that the cementitious medium not only contains portland cement but also contains ground granulated blast-furnace slag (GGBFS) or a pozzolan such as fly ash, silica fume, metakaolin, volcanic glass or calcined shale - any of which may have been included for economic reasons. If, however, the person selecting the ingredients for concrete knows that the aggregate is reactive (with no alternate nonreactive aggregate available) and if the person knows that the only available portland cement has a high alkali content (i.e., more than 0.6% Na2O.; Na2e = % Na20 + 0.658 x % K20), then it becomes irresponsible not to establish what reasonable precaution one should take. Professor Leming suggests using one of the following: 30% Class F fly ash, 50% GGBFS or 7% to 10% silica fume. My view is that one should prepare test specimens with the cement and aggregate to be used and then expose these both with and without at least two dosages of each of the various alternative materials (slag, pozzolan and lithium salts), so that the required dosage. to control the expansion is established. Then, economic considerations can dictate the final selection. I would point out to the author that GGBFS is not a pozzolan and is not an admixture, but, rather, it is a latent hydraulic cement. An admixture is, by definition, a material other than hydraulic cement. I commend him for suggesting that aggregate producers should become more active in knowing about the reactivity of their products and the precautions needed to permit those products to be safely used in concrete.

Jan 1, 1997

By John A. Kaufman, Terry D. Vandell

Recent mining regulations have increased the need for detailed engineering and environmental information pertaining to the hydrogeologic environment in mining areas. The cost of obtaining such hydrogeologic information has also increased. After mineralization of potentially economic grade ore and tonnage has been identified, and after completing preliminary mining feasibility studies (suggesting that development is merited), a second exploration phase can incorporate a simple, cost-effective baseline hydrogeologic data reconnaissance program that is limited but useful. Using exploration drill holes only, this program can provide a direct indication of where ground water is encountered. Also, reasonable estimates can be made on the relative production of water from various water-bearing strata, a composite potentiometric surface map can be prepared, and the general chemistry of the ground water can be characterized. This article outlines what typical baseline hydrogeologic data are needed and describes how it can be easily obtained during exploration drilling. Introduction Major engineering and environmental ground water parameters can be identified early in a project by using, drill hole data obtained from a mineral exploration program, designed by the mine geologist and hydrogeologist. Most importantly, data obtained in the exploration drilling program can be used to design a logical, defensible, and cost-effective baseline ground water data reconnaissance and monitor well program, which would be required for mine design and ultimately for mine permit approval. Drilling Where possible, exploration drill holes should be drilled with conventional rotary drilling equipment using air or, if necessary, water as the drilling fluid. Rotary air or water drilling generally allow good delineation of the first major saturated or water-bearing zone. If mud must be used during drilling, distinct hydrogeologic zones can still be defined, although the task may be considerably more difficult. Water Levels Static water levels can be obtained from selected exploration drill holes at specific depths while additional boreholes are drilled. Such measurements should not, however, be conducted until the hole has been developed with air (no water) and has stabilized at each of the depths to be measured. Such water-level information can be particularly useful when more than one aquifer exists. Where mine development is eminent, the hydrogeologist should install 50-100 mm (2-4 in.) diameter PVC casing in select drill holes. The PVC should be slotted, gravel packed, and properly sealed so additional hydrogeologic data can be collected for specific hydrogeologic zones at a later date. Such data could include water level information, permeability estimates based on injection and /or pumping tests, and water quality data. Where casing is not installed in drill holes, or when the drill holes are abandoned, the holes should be properly grouted and back-filled to the ground surface to prevent potential future ground water contamination. Monitoring Air Lift Water Production Estimates of the relative production from various water-bearing strata can be obtained from selected exploration drill holes. If ground water is encountered, its air lift (ground water flow) production can be measured at distinct intervals using a surface water flow measuring device, such as a portable Parshall

Jan 2, 1983

By Leonid Pevzner, Valerie Dmitriev, Yuri Babitchev

Performance of belt conveyors, service life of belts and mechanical elements can be radically improved if the automatic adjustment of the belt speed movement is made in such a way, that the unit load over the conveyor length be constant and close to the rated one under random input freight traffic. Such an adjustment is possible when the system of a controllable thyristor electric drive on the basis of induction squirrel cage motor is used. Computer-aided adjustment of the belt conveyor movement is effected via bicontour digital control of the main drive in order to redistribute loads when the loading of conveyor and contour of the control of tension drive are changed. The system envisages control and condition monitoring of the conveyor electromechanical system, as well as metering of electrical power and the amount of conveyor freight. The results of the simulation of speed control of the conveyor belt are given in the report. Mathematical model of the conveyor electromechanical system describes the movement of the belt with cargo and the tension drive. The input cargo traffic is assumed as stationary ergidic random process with the assigned characteristics. The solution of the problem of the synthesis of a closed-loop control system, the structure and parameters of adjustment, the conditions of asymptotic stability of the control back-up system and the condition of minimization of mean square error of shadowing are also given in the report. Microprocessor controller is used to realize the function of the adjustment unit. Under this control system standard mode of conveyor operation, different modes of start-up, operating mode with decreased speed when transporting people, service and emergency braking of a conveyor and some other modes are realized. The digital model of a conveyor as an instrument for decision making in case of emergency is used in those modes. MASTER TEXT Long-standing practice of belt conveyor operation in mines of Russia has proved their inefficient use with 40-70% capacity and 20-25% availability factor. It is associated with unreasonable power intensity and reduction of service life of mechanical components, and as a result, with the growth of total transportation costs. Low efficiency of conveyor application can be explained by the extremely irregular distribution of conveyor freight traffic. Usually, the width of a conveyor belt is identified in accordance with the possible maximum traffic value, engine power capacity for long-term operation under rated loads. However, actually a conveyor often runs without any load and its average load in most cases is lower than the rated one. The problem can be eliminated by way of the adjustment of the operational mode of a conveyor according to an actual input freight traffic via belt speed control providing for the conveyor regular linear load which is nearly equivalent to the rated one. Experimental research into freight traffic under working conditions of the operating underground and open-cast mines proves the fact that the actual freight traffic can be adequately presented through the model of stationary random function of time, for ex- ample, as a J (t) continuous random Gaussian process that is modulated with a G(t) elementary pulse flow:

Jan 1, 1996

By B. Hornsby

At the Mount Isa mine, Mount Isa, Qld., Australia, sublevel open-stope mining is used for copper ore while both sublevel open-stope and cut-and-fill methods are used for the silver-lead-zinc ores. Production in 1979¬80 was 4 730 000 t (5,200,000 st) copper ore and 2 590 000 t (2,850,000 st) of lead ore. The deepest mine level currently is 960 m below the surface. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The mine is located in the valley of the Leichhardt River in Lower Proterozoic sediments of the Mount Isa group. The regional strike of the sediments is north¬south and they have a persistent westerly dip of about 1.1 rad (65°). In the mine area, the Mount Isa group comprises a sequence of alternating bands of dolomitic shales and siltstones some 3.2 km (2 miles) in width. It is bounded on the east by greenstones and quartzose sediments of the Eastern Creek volcanics, and on the west by the Mount Isa fault, west of which occur schists and other metamorphic rocks. The ore bodies as currently known at Mount Isa are restricted to the Urquhart shale, a formation of thinly bedded pyritic, dolomitic, and volcanic shales some 1070 m (3500 ft) thick. Towards the top of the Mount Isa group sediments, copper and silver-lead-zinc ore bod¬ies occur as contiguous but discrete entities and are mined and treated separately (see Figs. I and 2). Argentiferous galena, sphalerite, pyrite, and minor associated sulfides occur in distinct concordant bands throughout the Urquhart shales. Wherever these bands are grouped together in sufficient density they constitute silver-lead-zinc ore bodies with widths varying up to 36.6 m (120 ft). Other mineralized bands are common in intervening beds. Individual ore bodies persist for many hundreds of meters concordant with the strike and dip of the enclosing shales. Intersections of these beds with fold axes provide local zones of enrichment but otherwise the mineral content of the ore bodies varies only slightly throughout the extent of the dip and strike. Chalcopyrite is the only important primary copper mineral. It occurs in association with pyrite and pyrrhotite as disseminated flocks and as vein fillings throughout irregularly shaped zones of folded, brecciated, and re¬crystallized Urquhart shale. These zones, which are lo¬cally termed "silica-dolomite" bodies, are broadly transgressive to the shale bedding and confine all significant copper mineralization to the virtual exclusion of silver¬lead-zinc mineralization. In some areas, the downward percolation of acidic water through faults and shears has caused extensive leaching of the coarse-grained carbon¬ates to depths in excess of 610 m (2000 ft), but most of the silica-dolomite remains unleached and the ground is competent. The majority of lead ore being mined is north of the main shaft pillar (R62, U62) area. The major lead¬producing areas for many years have been the Black Star ore bodies (2 and 5 ore bodies) and the Racecourse ore

Jan 1, 1982

By P. R. Taylor

This work is concerned with the extraction of refractory metals using an electro-reduction process, in which a molten oxide melt, instead of halide, is used as the electrolyte. The process may provide an alternative method of producing refractory metals from their ores through use of a reverse-polarity direct current (DC) plasma arc heating process. In such a process, the plasma torch itself acts as an anode, and resulting liquid or solid product metals work as a cathode, whereas the molten oxide melt plays the role of an electron transfer layer. The focus of this study is: the electro-reduction of scheelite; vanadium pentoxide; and chromite. For the vanadium pentoxide, the proposed melt is mainly composed of CaO-V2O5/Li2O-B2O3-V2O5or FeO-CaO-SiO2-V2O5-Li2O with the addition of other alkali and alkaline metal oxides. In the case of scheelite ore, the SiO2-CaO-Li2O-WO3system is used as melt and metal aluminum or nickel could be used as a collecting media. As for the reduction of chromite ore, SiO2-CaO-Cr2O3-Li2O system with trace amount of CaF2is used as the melt. As a demonstration, chromium was successfully produced at a laboratory scale through the plasma driven electro-reduction process. One of the studied slags had a composition of 13.8% CaO; 4.9%CaF2; 36.4% Cr2O3; 6.9% Li2O; and 38.0% SiO2. Two observations are significant in this laboratory scale study. The first one was that the amount of Cr2O3and FeO, which were predominantly electronic conductors in the oxide melt, greatly affected the conducting mechanism of the melt. With high concentration of Cr2O3and FeO in the melt, the current efficiency was fairly low. In this case, chromium was found to be barely reduced because of electronic conducting mechanism. For example, with initial slag of 60% Cr2O3, no chromium was found reduced. With low concentration of Cr2O3and FeO in the studied melt, typically no more than 30% Cr2O3, it was observed that chromium was readily reduced due to the dominant ionic conducting mechanism. The second observation was that the addition of SiO2tothe melt helped to make the oxide melt more ionic, which was apparently desirable to the molten oxide electrolysis. However, high content of silica had a negative effect on the fluidity of the melt. This was resolved by adding trace amounts of CaF2to the melt. Therefore, by judicious selection of oxide melt, refractory metal oxides might be dissolved into it and yet the melt itself retains the required ionicity. A reverse-polarity DC plasma driven molten oxide electrolysis may prove to be a viable alternative route for the extractive metallurgy of refractory metals.

Jan 1, 2003

By Erik Westman, Enji Sun, Xu Ma, Ben Fahrman

"Shale gas has become an increasingly important clean energy, which has been explored worldwide in recent decades. Supercritical CO2 acts as fracturing fluid for shale gas production. The safety monitoring is essential to prevent any kinds of leakage from the reservoir as the supercritical CO2 physically stored hundred kilometres underground. Seismic tomography is an imaging technique that uses induced seismic waves to create three dimensional images of the subsurface. It is an effective monitoring method to evaluate the caprock integrity in the carbon dioxide sequestration storage (CCS). In this experimental research, a simulated uniaxial compressive load is applied on a granite sample to analyze the stress redistribution for long-term in-situ caprock integrity during CO2 injection. The induced seismic waves are recorded and seismic events are traced based on the Geiger algorithm. The frequency of seismic events correlates with the caprock failure evolution. The acquired seismic data is divided into four regimes based on the frequency of seismic events and the failure process to examine the failure evolution. Furthermore, the travel time and distance is plotted to analyze the variation of velocity. Finally, the double difference tomography (TomoDD) algorithm using arrival time is adopted to recalculate the locations of seismic events and velocity structure in each regime. The results indicate that the passive seismic system can map the caprock stress distribution and allow for imaging of the caprock integrity. TomoDD exhibits sound improvements to relocate seismic events both in relative and absolute locations as well as to characterize the local velocity structure. The study further reveals that seismic monitoring along with TomoDD could evaluate the caprock failure accurately in the CCS.Introduction To reduce the CO2 concentration in the atmosphere, CO2 capture and sequestration (CCS) has been suggested to as a means of continuing to use fossil fuel resources while offsetting their negative environmental impacts (Eiken et al 2011). A positive CCS project should retain 99% of the injected supercritical CO2 (pressure is greater than 7.38 MPa and temperature is above 31.04? and a density is of about 700 kg/m3) over at least 100 years (Davidson et al 2005). As large quantities of supercritical carbon dioxide are being injected into full scale storage projects, caprock stress is redistributing and the leakage could occur anywhere over a wide storage area (Hou et al 2012). Acoustic waves are emitted from the caprock, as it fractures due to the CO2 injection, which can be detected by passive seismic sensors (Shitashima et al 2013). Tomography techniques are advantageous for imaging the integrity of the caprock in the CCS projects. Velocity tomography uses waves to model entities based on the arrival time of waves (Westman et al 2001, Westman 2004, Luxbacher et al 2008). Seismic tomography is a data inference technique that exploits information contained in seismic records to constrain 2D or 3D models of the Earth's interior. It generally requires the solution of a large inverse problem to obtain a heterogeneous seismic model that is consistent with field observations (Kudryavtsev et al 2012)."

Jan 1, 2017

By George H. K. Schenck

INTRODUCTION Boom-type miners mechanize the cutting and loading of a solid face of rock having a compressive strength as high as 124 MPa (18,000 psi). These machines differ from continuous miners in that they can cut much harder rock for any given cutter-motor power. In addi¬tion, a boom miner is more flexible, selectively cutting any cross-sectional configuration from circular to square arched faces, 1.57-rad (90°) turns, and mixed faces. The basic operational concept of these machines, utilizing a rotary cutterhead mounted on a slewing boom, gained importance in Europe during the 1960s, where, due to their specialized use in roadway development in coal mines, they were called roadheaders. Along with continuous miners, boom miners share the ability to fully mechanize the cutting and loading of rock, while eliminating the need for explosives and the shattering and overbreaking of roof and rib rock that is normal with conventional mining methods. The machines are crawler-mounted and most have a gathering-arm load¬ing system that, moves the cut rock onto an internal chain conveyor, subsequently discharging the rock into a transport device such as a shuttle car or a bridge conveyor. Light- to medium-weight boom miners are cutting softer rocks and minerals successfully, including coal, shale, rock salt, potash, phosphate, weak sandstones (e.g., those associated with uranium ore), and other softer ores such as iron. Heavy third-generation ma¬chines have extended rock cutting to much harder ores such as borate, oil shale, and almost all rock associated with coal seams, except for the harder sandstones and limestones. The mention herein of specific manufacturers, brand names, or models is made by way of example only and does not constitute endorsement by the author or The Pennsylvania State University. All costs cited herein are in 1977 US dollars. TYPES OF BOOM MINERS All boom miners utilize drag bits fixed on a rotary cutterhead that is powered by an electric motor mounted in the slewing and elevating cutter boom. The cutter¬head is either a ripping or a milling type, and the machines have evolved through three generations (Boldt, 1977). As shown in Fig. 1, only one boom miner cur¬rently produced can use both ripping and milling cutter¬heads on one machine. Table 1 lists boom-miner models built in large num¬bers and/or successfully used or marketed in North America. Table I excludes machines of which only a few have been produced and none sold in North America, such as those manufactured by Demag, Eick¬hoff, Paurat, and Thyssen-Rheinstahl. The only Ameri¬can boom miners are the F-16 and Super ROC¬MINER"', manufactured by AEC, Inc., State College, PA. Machine Generations Three generations of boom miners can be distin¬guished according to their times of introduction, their rock-cutting abilities, and their weight classifications. Fig. 2 illustrates typical best-practice production rates possible from boom miners for selected cutter-motor power sizes (other power figures can be interpolated). Productivity is related directly to the energy applied to the cutterhead and indirectly to machine weight; higher

Jan 1, 1982

By Henry N. McCarl, Gary Waters, William A. Vogely

INTRODUCTION In the past three decades, world trade has grown from less than $100 billion per year in the years following World War 11 to slightly more than $300 billion in 1970 and over $2,000 billion in the early 1980s. Adjusted for inflation, the real growth of world trade in 1972 dollars increased from less than $175 billion per year in the early 1950s to slightly more than $342 billion in 1970 and almost $700 billion per year by the early 1980s. Thus trade as a whole has increased a little more than twofold in real terms in the past decade." Mineral commodities constituted approximately 20% of the value of total world trade in 1970, and significantly more than that proportion in terms of physical volume. By 1980, de- spite rapidly rising petroleum prices, mineral commodities accounted for roughly 18% of the total value of world trade. Crude oil alone ac- counted for about 16%, making it the single most important commodity in international trade. The worldwide recession of 198 1- 1983 brought a dramatic decline in both volume and price of crude oil, shrinking the impact of mineral commodities to roughly 10% of the value of total exports, worldwide, in 1982- 1983. The decline of mineral commodities as a pro- portion of the value of world trade in the decade 1970- 1980 is due largely to the increasing importance of manufactured goods and consumer products such as automobiles and electronic items. During this period, mineral commodity trade expanded roughly sixfold in terms of current dollars to an estimated $350 to 360 billion in 1980. This was equivalent to doubling the real value of mineral commodities in international trade in the 1970- 1980 period in constant dollars. The U.S. Bureau of Mines has expanded the traditional definition of mineral commodities to include semifinished products such as iron and steel (in addition to iron ore), refined metals such as copper, lead, zinc, aluminum, and tin, concentrates, scrap, and petroleum products. Since large quantities of essentially mineral derivatives travel in this form, it is reasonable to use these expanded definitions in stating the role of minerals in world trade. Thus minerals in world trade comprise 30 to 33% of total export trade in all commodities during the period 1976- 1980 (see Table 1.3.1). In addition, the U.S. Bureau of Mines estimates the value of all mineral commodities consumed in the world (at the national level) and compares this value to total worldwide commodity consumption. By this system, mineral commodities range from 30 to 40% of all commodities consumed each year in all countries during the period 1976- 1980 (see Table 1.3.2). The growth in export trade in mineral commodities by commodity group is shown for the period 1976-1980 in Table 1.3.3. These data parallel the swings in worldwide economic activity during the same time period. By any of the above measures, minerals, especially the fossil fuels, constitute a significant proportion of both total economic activity and

Jan 1, 1985

By J. A. Folinsbee

Placer Dome Canada owns and operates the Campbell Mine at Balmertown, in the Northwestern corner of the Province of Ontario, Canada. The mine operates at 1500 stpd and produces in excess of 300,000 oz of gold annually. Recent changes to the gravity concentration circuit have resulted in a 10-15 % increase in gravity recovery. The circuit changes responsible for these improvements will be the focus of this paper.

Jan 1, 1997

By Arnold Griffin

Numerous articles have been published describing the procedures and solvents used for the recovery of gold from ores and industrial products. I consider that the most innovative gold solvent is weak cyanide solution as described in the McArthur-Forrest patents issued in 1887 and 1889. This fundamental process is still applied in spite of the efforts of numerous researchers to develop more effective and economic alternative solvent.

Jan 1, 1998

By K. C. Nathsarma

An attempt was made to extract niobium oxide from ~98.5% Nb2O5 using solvent extraction processes. Nb2O5 is used as the feed material in carbothermic reduction processes aimed at producing high-homogeneity, super-conductor-grade niobium on a laboratory scale. The Nb metal used for superconductor applications requires a residual resistivity ratio (RRR) > 300, which in turn needs a stringent purity of Nb and allows impurities (substitutional and interstitial) in ppm levels only. In this paper, solvent extraction of niobium was studied under various experimental conditions, such as effect of different extractants, concentration of methyl isobutyl ketone (MIBK) in the organic phase and concentration of various acids. The concentrate was digested with hydrofluoric acid, with ammonium fluoride (NH4F) as a stripping agent. The extraction of niobium from low hydrofluoric- (HF-) bearing solution was found to be low. Thus, various concentrations of hydrofluoric acid and sulfuric acid, as well as hydrofluoric acid and hydrochloric acid, were investigated towards obtaining a maximum amount of niobium in the filtrate and a minimum amount of niobium in the residue. A McCabe - Thiele plot for extraction of niobium from the aqueous phase, HF-bearing solution using HCl with 85% MIBK in kerosene has been constructed to determine the O:A ratio and the number of stages of the process.

Jan 1, 2011

By K. C. Nathsarma

An attempt was made to extract niobium oxide from ~98.5% Nb2O5 using solvent extraction processes. Nb2O5 is used as the feed material in carbothermic reduction processes aimed at producing high-homogeneity, superconductor-grade niobium on a laboratory scale. The Nb metal used for superconductor applications requires a residual resistivity ratio (RRR) > 300, which in turn needs a stringent purity of Nb and allows impurities (substitutional and interstitial) in ppm levels only. In this paper, solvent extraction of niobium was studied under various experimental conditions, such as effect of different extractants, concentration of methyl isobutyl ketone (MIBK) in the organic phase and concentration of various acids. The concentrate was digested with hydrofluoric acid, with ammonium fluoride (NH4F) as a stripping agent. The extraction of niobium from low hydrofluoric- (HF-) bearing solution was found to be low. Thus, various concentrations of hydrofluoric acid and sulfuric acid, as well as hydrofluoric acid and hydrochloric acid, were investigated towards obtaining a maximum amount of niobium in the filtrate and a minimum amount of niobium in the residue. A McCabe - Thiele plot for extraction of niobium from the aqueous phase, HF-bearing solution using HCl with 85% MIBK in kerosene has been constructed to determine the O:A ratio and the number of stages of the process.

Nov 1, 2011

By J. Yao

Synthetic indium-bearing zinc ferrite (IBZF) was mechanically activated by a tumbling mill. Subsequently, the behavior and kinetics of leaching zinc and indium from the initial IBZF and activated IBZF in sulfuric acid solution were investigated. The results demonstrate that the tumbling ball milling enhances the leaching reactivity of IBZF and increases the zinc and indium extractions. The reaction temperature and H2SO4 concentration have an important effect on leaching zinc and indium from the initial IBZF and activated IBZF. The kinetic model -ln(1-x) = kt was used to describe the kinetics of leaching zinc and indium from the initial IBZF and activated IBZF and to calculate the kinetic parameters. The tumbling ball milling causes a decrease in activation energy and reaction order, which indicates that the dissolution of IBZF after mechanical activation by a tumbling mill becomes less sensitive to temperature and H2SO4 concentration. For the zinc leaching, the activation energy decreases from 73.9 to 70.3 kJ/mol and the reaction order decreases from 0.72 to 0.70. For indium leaching, the activation energy decreases from 78.1 to 73.5 kJ/mol and the reaction order decreases from 0.82 to 0.69. It is found that the dissolution rates of the initial IBZF and activated IBZF are controlled by surface chemical reactions.

By A. Bruynesteyn

Most ores and coals contain sulphide minerals such as pyrite, FeS2, the sulphur portion of which is a ready substrate for a variety of sulphur oxidizing bacteria. Although there are several bacteria capable of oxidizing sulphide minerals, the most often discussed culprit is Thiobacillus ferrooxidans.. Oxygen from the air slowly oxidizes pyrite into sulphuric acid, but T- ferrooxidans can increase this reaction rate several 100,000 times.

Jan 1, 1991

By Antonio Jorge de Sousa

In order to compare several mining variants, on the point of view of the variability of the ore quality parameters, a conditional simulation technique is applied to a complex pyrite deposit (FEITAIS orebody, Portugal). Exploitation methods such as cut and fill and sublevel stoping are studied by the a.m. methodology. For each mining variant, it is assessed the influence of several mining operators on the variability of grades.

Jan 1, 1982

By S. Dinescu

The paper deals with the modeling of longwall shearer cutterhead interaction with the coal, in order to study the influence of different limiting factors of the haulage speed, and the cutting regime ensuring optimal energy consumption A computer simulation model is used to draw-up the torque vs haulage speed and the haulage force vs haulage speed dependence diagrams, for different strength of coal and different degrees of bit wear.

Jan 1, 2008

By Robert Martinez

A proven high grade reserve of gold mineralization located in Mexico is evaluated to determine which gold recovery process is best suited for this deposit. The processes evaluated are; Heap leaching, Vat leaching and a CIP circuit. All qualify as viable options, however each one presents a different economic picture which is impacted substantially by the financial constraints of the project. Taking this into consideration the most economic process was selected.

Jan 1, 1987

By Anthony Busigin, Stephen Pogorski, Colin R. Phillips

The precision of radon daughter measurement techniques is a complicated function of uncertainties arising from concentration and flowrate fluctuations during sampling, counting statistics and many other factors. Optimization of a measurement technique requires that all these uncertainties - not just counting statistics - be considered. In this work, the optimization procedure of Busigin and Phillips (1980) is tested against Monte Carlo experiments for the case of the modified Tsivoglou method.

Jan 1, 1981

By K. N. Han

Copper and nickel are extracted from their elemental state, complex sulfides, ores, and other materials such as scrap by leaching them with a solution containing halogen salts - bromine/bromide, and/or iodide/iodine, oxygen and sodium or potassium nitrate. This US patented process is extremely effective yielding 98% recovery in15 minutes for the treatment of chalcopyrite and pentlandite in an autoclave at a temperature of 100°C - 150°C.

Jan 1, 2003