Search Documents

By Y. Zimmels, C. Feldman

Closed-circuit grinding processes are considered in the context of a reactor-separator circuit that involves multifraction streams and products. Because grinding circuits are low-efficiency, capital-intensive operations, modeling to maximize their economic return is appropriate. An attempt to develop and test such a model is presented in this work. The model relies on process simulation for both the mill and the separator, in conjunction with constraints imposed by product specifications. The grinding process was simulated using breakage functions, which provided complete data on the feed and product of the mill. A cyclone bank used as the separator was also simulated using known models. The overall process model provided a complete simulation of the multistream grinding and separation process. The process model was then incorporated into an economic model that predicts grinding cost, subject to process constraints, for a given set of operating variables. The model facilitates economic optimization of the grinding process as it relates to process variables and process hardware.

Jan 1, 1993

By Jae-Chun Lee, Kang-In Rhee, D. B. Dreisinger, Hyo-Shin Yu, G. A. Kordosky

The development of a process for direct synthesis of very pure ZnO powders from zinc-bearing waste was investigated. The zinc waste which contains 55% zinc was leached with sulfuric acid. After iron removal by hydrolysis from this zinc solution, purification through solvent extraction by the use of D2EHPA as an extractant was carried out. Then, loaded zinc in the organic solution was stripped and precipitated simultaneously using oxalic acid as a precipitant. Synthesized ZnC2O4 precursors by precipitation stripping were calcined to obtain ZnO powders exceeding 99.9% purity. The effects of sulfuric acid concentration, leaching time, and pulp density on the extraction of zinc were studied and optimum conditions for the solvent extraction were obtained through purification of the zinc solution. The size, morphology, and size distribution of synthesized ZnC204 powders were studied in terms of oxalic acid concentration, temperature, surfactant added, precipitation time, etc.

Jan 1, 1993

By Scott G. Britton

Many times during the construction of a project, whether large or small, the engineer will become involved with management of the work and workforce. In some cases, mine management will turn over the direction and responsibility of doing the work to the engineer. Because of this, it is important to know some of the basic principles of human resource applications- among other management concerns. This chapter, therefore, looks at the fundamental principles of human resource management. Three broad discussions are presented to the reader. These are: (1) organization, communications, and responsibilities of management; (2) analysis of worker motivation; and (3) supervisory leadership. Each topic encompasses the current thinking for coal mining and mining management. Much of the information in this chapter comes from Practical Coal Mine Management, by this author and published by John Wiley & Sons, Inc., which discusses in depth many of the ideas presented here. Interested persons are directed to this text for more information on management skills.

Jan 1, 1983

By Kot F. v. Unrug

In spite of extensive research and accumulated experience from mining operations, appropriate coal strength values for pillar design remain debatable. Coal strengths determined in the laboratory on standardized samples vary widely among various coal seams with poor repeatability. Penetrometric in situ strength testing obtains multiple measurements at multiple horizons within the coal seam to provide a strength profile. Alliance Coal has used that method in many of its mines for pillar design. Pillars in these mines perform well. This paper presents a series of case studies and discussion of issues related to coal pillar design. The analysis demonstrates that the proposed default in situ strength of 900 psi is appropriate when no other data exist. However, in the case of appropriate strength measurements combined with analysis of pillar structural composition, differing values can be used successfully. In areas where the penetrometric derived in situ strength is greater than the standard 900 psi in situ strength, reserve recovery has been optimized as required by law without compromising safety.

Jan 1, 2009

By N. Kuyucak

Acid rock drainage (ARD) resulting from the natural oxidation of sulfide mineral wastes has become a major concern to the mining industry, both during the operational period and after mine closure. ARD is generally characterized by high acidity and high concentrations of dissolved metals and sulfates. If the generation of acid cannot be prevented or controlled, it must be treated to eliminate acidity and to reduce the concentration of heavy metals and suspended solids before release to the environment. Microorganisms play an important catalytic role in the generation of ARD. Several prevention, control and treatment technologies that are based on microbiological activities have been developed. The role of microorganisms and biotechnology in the generation of ARD and their role in the methods used for prevention, control and treatment are discussed in this paper. Recently developed passive and biological treatment processes that have been implemented at mine sites are emphasized in this paper. Benefits, limitations and design criteria for passive biological processes are also presented.

Jan 1, 2000

By G. Baudet, M. Save

Ethoxylated phosphoric ester surfactants were evaluated as collectors for flotation of carbonates from sedimentary phosphate ores, at slightly acidic pulp pH, using sulfuric acid or sodium fluorosilicate as a phosphate depressant. With 12 to 15 carbon atoms in the hydrophobic chain, maximum collecting power was observed for 9 to 10 ethylene oxide units. Only fine carbonates, ranging in size from about 20 to 160 µm or 40 to 200 µm, were effectively removed with phosphoric ester collectors. Utilization of seawater, or water of extremely high hardness, did not detrimentally affect selectivity. Silica, silicates, and residual fine carbonates can be separated in a second flotation stage, with primary amine as a collector. Coarse carbonates are separated by direct flotation of phosphate with fluoride ion as a phosphate activator and primary amine as a collector. In a seawater pulp, fluoride ion was not required. Typical examples of laboratory and pilot- scale test results are given to illustrate capabilities of the various flotation flowsheets.

Jan 1, 1999

By R. E. J. Putman

The past ten years have witnessed substantial development of electronic equipment for execution of process control functions. The methodology of giving instructions to the data-handling system and the organization of the system, both the equipment and instruction coding taken together, have developed simultaneously. Examples of the technology specific to the mineral processing industry can be cited. Approaches to system design developed for the Pinto Valley concentrator incorporating slave and master data processing have been described by Arney, and his associates (1974). Madge (1970) has described the hierarchical systems employed at the operations of Cominco Ltd. The Kennecott Garfield smelter is controlled by a system of microprocessors linked to a general purpose data processor (Marchant, et al., 1977). These systems provide innovative approaches to couple advancing technical capability in electronic data processing to the objectives of process management. The current state of the art described in this chapter is certain to require updating in the 1980's with the advances in technology anticipated.

Jan 1, 1979

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By C. W. Matthews

Introduction Screening is an art, one of the oldest in the process field today, and one of the most widely used in our present age. Screening is being applied to an ever-increasing number of assignments, in an ever-expanding circle of industries. Screening is defined precisely as a mechanical process which accomplishes a separation of particles on the basis of size and their acceptance or rejection by a screening surface. Particles are presented to apertures in a screening surface and rejected if larger than the opening, or accepted and passed through if smaller. Screens are machines with screening surfaces used to classify materials by size. The screening surface is the medium containing the apertures for the passage of the undersize material. Screens are put to many uses - size separation, dewatering, desliming, media recovery, scalping, trash removal, washing, dedusting, conveying, concentration, and many combinations of these functions. It is interesting to note that screens are used for handling commodities

Jan 1, 1985

By Kerry Burns

Contrary to active subsidence, which occurs concurrently with mining operations, or is completed within a few days following coal extraction, delayed subsidence may take many years to appear at the surface after coal mines are abandoned. There are two principal morphological types of delayed subsidence: troughs, which are shallow depressions, and sinks, which are steep-sided crown pits. Both types are damaging to surface structures, and a variety of methods have been introduced to deal with the problem, ranging from subsidence insurance to site restitution. In planning insurance or restitution measures, a predictive model is of value in estimating the magnitude of the problem and the size of long-term budgetary commitments. Only one model is known, which was developed for the Bureau of Mines by GAI Consultants of Monroeville (l,2,3). The GAI model is presented in qualitative terms. This report develops a formal basis for the model and tests a numerical implementation on one of the best-described study areas, Allleqheny County in Pennsylvania.

Jan 1, 1982

By Robert A. Bauer

Geology and weather effects produce natural ground movements that may be misinterpreted as mine subsidence. Weather, local geology and vegetation clearly influence the elevation of the ground surface through frost action and changes in groundwater levels and soil moisture content. Common practices of monument and benchmark design and placement do not address the problem of natural ground movements. Monuments can be designed to minimize some natural ground movements. Differential displacements can be reduced by knowledgeable placement of benchmarks and monuments which are of similar design and construction. Commonly, the threshold values of movement for the determination of mine-induced subsidence are dependent on the closure errors (accuracy) of individual surveys. Accuracy is more than the amount of closure error; it should include the range of elevation changes (error band) determined for each monument over a period of time before it is disturbed by mining. Multiple baseline surveys of the entire monitoring system, conducted before the onset of subsidence, should be used to establish subsidence detection limits.

Jan 1, 1986

By J. Engesser

A research project was undertaken to determine if coal addition tofluxed-magnetite pre-fired pellets would reduce nitrogen oxide (NOx)emissions during pellet induration. Iron oxidation rate tests, coal oxidation rate tests and calcination rate tests were conducted in a laboratory furnace to determine the amount of coal necessary to provide adequate heat for limestone calcination without producing detrimental effects to magnetite oxidation. Pilot scale pot-grate tests were then performed with and without coal in the pre-fired pellets to verify pellet quality parameters and nitrogen oxide emissions. The off-gas during each pot-grate test was analyzed for NOx, CO2, CO, SOx, and O2. There was approximately a ten percent reduction in NOx emissions with coal addition during the normal pot-grate firing cycle. There was a 75% reduction in NOx emissions during firing cycles that used 25% to 75% excess air during firing rather than the normal 300% excess air.

Jan 1, 2003

By L. Hagenbuch

Off-highway truck purchasers know the amount of tonnes, pounds, kilograms, etc, a truck will carry. However just because a truck is rated at 240 tons may in no way correlate to what that truck will actually carry. Two numbers define the carrying capacity of an off-highway truck: 1. The weight carrying capacity of the truck; 2. The volume carrying capacity of the truck. These two numbers must be in sync or the amount of payload carried will vary from the carrying capacity of the truck. Currently the Society of Automotive Engineers (SAE) standard J1363 January 1985 defines the volumetric carrying capacity of an off-highway truck. However as is well known in several South American countries, the SAE standard overrates the truck’s effective volumetric carrying capacity 15% to 20%. This paper presents a method for measuring “effective” body volumetric carrying capacity, resulting in a truck body for carrying the targeted load, matched to the loading equipment that interacts positively with the truck chassis.

Jan 1, 2002

By Qing-Wang Hao

In this paper, the authors attempt to develop engineering based approaches for estimating safety factors against pillar and floor failures and predicting likelihood of subsidence events over abandoned coal mines in Illinois. There are two critical problems involved in the analysis: determination of geotechnical properties, and consideration of time effect. The authors attempt to solve the problems by generating hypotheses, which are used to modify existing engineering models for estimating pillar and floor safety factors. The modified models are validated using data from two well established databases of subsidence events over active and abandoned mines in Illinois. The data analysis suggests that most of the trough type subsidence events in Illinois were caused by floor failures rather than pillar failures. The subsidence incubation period seems to be directly related to initial floor safety factors at the time of mining. This correlation can be used to predict the likelihood of subsidence and to assess subsidence risks within both spatial and temporal contexts where detailed mine maps are available.

Jan 1, 1986

By D. E. Ranta, M. W. Ganster, A. D. Ward

An ore zoning technique developed by Climax geologists during the past forty years has been used to contour drill-hole assay values on cross-sections for fourteen porphyry molybdenum deposits in western North America, including the Climax and Henderson orebodies. Detailed geological studies of these large, complex deposits are essential in determining ore controls, which are the factors most critical to the zoning of MoS2 and to conceptualizing geologic models. The technique provides a detailed representation of the size, shape, grade distribution, and geologic continuity of the individual deposits. It demands a disciplined approach and adheres to rigorous rules while maintaining flexibility for adaptation to widely varying geologic conditions. By defining the limits that guide and control manual, computer-assisted conventional, and geostatistical reserve estimates, it exerts a strong geologic influence on the estimation process. A combination of ore zoning and geostatistical analysis of molybdenum deposits produces a significantly more accurate, precise, and defendable geologic reserve estimate than other methods.

Jan 1, 1992

By G. M. (Frits) Swinkels

The Apex property, mined in the early Twentieth Century for direct shipping copper, also contains gallium and germanium in iron oxide minerals. In 1982, Musto Explorations Limited began an exploration program to define reserves. A metallurgical process was developed, and a production decision was reached in late 1983. This text describes the process development and design. The Apex mine, located near St. George in Southwestern Utah is owned by St. George Mining Corporation, a subsidiary of Musto Explorations of Vancouver, B.C. Musto acquired the property in early 1982. A pilot plant was operated by Hazen Research, Inc., Golden, CO later in 1982. In late 1983 sufficient information had been developed for St. George to proceed with the project. The final process design was prepared by G. M. Swinkels of Vancouver, consultant to Musto, and Hazen Research. Process engineering was done by Hazen Research, and St. George acted as its own contractor. Commissioning of the plant began in October 1985.

Jan 1, 1986

By Roger L. Baer

Introduction Brief Review -SEC mission & history -Development of SEC mining disclosure guidelines -Principles of good public company ‘disclosure’ SEC staff views of alternative approaches to mining company disclosure -SME Resource & Reserve Committee – April 2003 Food for thought

Jan 1, 2003

By A. G. Journel

The regionalization of tungsten grades at the deposit represents an ideal case for anisotropic hole-effect variogram modelling. The modelling technique is presented step-by-step and the consequences of the model on block kriging are indicated.

Jan 1, 1982

By Kenneth A. Gutschick, Harry L. Francis

A large number of minerals and chemicals (Table 1), some mineral-derived, are used in the treatment of both potable water and domestic sewage waste water and solids (Anon., 1990). In water treatment there are ten principal process uses as shown in Table 2 (Anon., 1990), which also lists the major chemicals in each process. Since lime (calcium oxide, calcium hydroxide, and dolomitic lime) is the largest chemical (by tonnage) used in water treatment, this chapter will deal primarily with this product. Note that it is included in five of the process uses shown in Table 2, and that indirectly it is also used in at least one other category (taste and odor control, where lime is used with potassium permanganate to provide optimum pH condition). POTABLE WATER TREATMENT Water Softening The biggest use for lime in water treatment involves water softening, where it serves to reduce carbonate hardness caused by dissolved bicarbonate and carbonate compounds. Currently there are more than 1000 domestic water softening plants (Table 3) located in most sections of the country, but particularly in Ohio, other midwestern states, Florida, and Texas, where limestone bedrock abounds (Anon., 1990). Among the other uses for lime in water treatment are coagulation, disinfection, and removal of heavy metals due to high pH softening, removal of certain radioactive and organic compounds and fluorides, neutralization of acidic water, removal of silica, particularly with dolomitic lime, and removal of color. Most of the above advantages accompany water softening, although at some plants lime is used specifically for one purpose, such as silica removal with dolomitic lime, minimizing pipeline corrosion by addition of lime to correct an aggressive water, and others. Hardness in water comprises two types - carbonate hardness, caused by dissolved calcium and magnesium carbonates and bi- carbonates, and non-carbonate hardness caused by dissolved non- carbonate salts, particularly calcium sulfate, calcium chloride, magnesium sulfate, and magnesium chloride. Total hardness is the sum of the carbonate hardness and non-carbonate hardness. Waters are classified as soft (0 to 75 mg/L as CaCO,), moderate (75 to 150 mg/L), hard (150 to 300 mg/L), and very hard (above 300 mg/L). Most water plants strive to reduce total hardness to about 100 mg/L, although in recent years the tendency in some cities has been to allow a little higher value in order to reduce both chemical costs and the amount of water softening sludges produced. There are four basic types of softening plants: lime softening, primarily to reduce carbonate hardness; lime-soda softening, for reduction of both types of hardness (in some plants caustic soda is used in place of soda ash, but it is more costly); split lime-zeolite, where a base exchange mineral is employed in place of soda ash (this system also requires salt [sodium chloride] to regenerate the zeolite mineral); and finally zeolite softening, which is generally used in small systems for private houses and small municipalities. Principal disadvantages of the latter system are its relatively high cost and the salt requirement, which introduces considerable quantities of soluble salts into the waste water discharge system.

Jan 1, 1994

By Scott G. Britton

Until now, only the range of typical construction projects which are repeated over and over during the life of a coal mine have been discussed. This chapter looks at underground construction projects which occur only once or twice during the life of any given mine and are major construction projects in both time and cost. These projects usually require the services of an outside engineering and construction firm with hands- on experience in design installation. Because of this involvement with engineering and construction firms (EIC), the role of the construction engineer will change from one of actively de- signing and directing tasks to one of planning, inspection, and quality control. To reflect this role change in the discussions, the focus of this chapter will be changed to a broad overview of project participation. Of course, the projects under consideration in this chapter could easily fill more than one book on their design and installation. In addition, major construction projects are extremely site specific, requiring months of data collection about site geology, physical conditions, and potential excavation and construction requirements. Therefore, no attempt shall be made to discuss any detailed construction aspects as was done in earlier chapters. The purpose of this chapter is to present the fundamental concerns of a staff engineer or supervisor. This engineer does not make the decisions on choosing the EIC firm, but assists and interacts with their project team to accomplish the goals set forth by higher management. The construction topics to be reviewed fall into three main categories. The first category is highlighted by the installation of a main surge bin; the second is typified by the construction of an underground shop; and the third category encompasses special projects such as rotary dumps, crusher stations, and foremen's offices. These categories highlight the differences between degrees of mine responsibilities for project completion. The first topic is usually a turnkey project by an E/C firm for a given mine. The second topic represents the leading role of the mine in the project with a contractor as a support service or equipment supplier only. The third topic, special projects, is an example of a joint venture-between a contractor (leading partner) and mine management. These roles can change with any given project, but the changes in management responsibilities for the construction engineer can be nicely illustrated for the purposes of this text. The first step toward constructing major mine projects is to analyze the mine which influence their design. From the mine management standpoint, these parameters should reflect the role the mine will play in the project construction. In other words, what is the nature of the proposed mine environment and what are the material, labor, and time requirements needed to assist or direct the chosen engineering and construction firm? Answering these questions requires some basic project planning and cost estimation work. Here, only a general treatment is necessary, since detailed discussions of these topics will follow in Chapters 8 and 10. For those persons interested in the role of the EIC contractor, I suggest beginning by reviewing the article by Beall, "The Role of an Engineering and Construction Contractor," presented in the October 1980 issue of Mining Engineering magazine.

Jan 1, 1983