Search Documents

By Jon C. Volkwein

The U. S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography at the Pittsburgh Research Center. These gas results were analyzed for explosibility. Personal exposure to carbon monoxide was also monitored. The highest methane level observed was 9.55 pct. The Inert gas levels, (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were non-explosive. The maximum personal time weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining. INTRODUCTION The auger highwall mining method is an effective method to recover coal from a reserve when removal of the overburden by surface mining equipment becomes uneconomical. In this method of mining, a horizontal auger enters the coal seam from the surface mine bench under the highwall and the coal is drilled in a series of parallel holes. Historically, coal mined from the surface is relatively shallow, and over time, methane associated with the coal has dissipated through the surface. In most circumstances, little methane has been found associated with auger mining. However, mining technology has enabled surface mining of deeper reserves of coal. Furthermore, environmental constraints have forced the highwall extraction method to be used to remove coal under wetlands, further increasing the chances of encountering methane. Recently incidents of methane explosions at a few auger mining operations have resulted in injuries and increased testing for methane at the collars of auger holes. The fuel source of the reported explosions was not necessarily limited to methane, but may also have involved coal dust. The Mine Safety and Health Administration (MSHA) met with the Bureau to discuss what technology might be available to enable the safe resumption of mining. The discussion included the difficulty of ventilating through the solid shafts of the augers, that steel bits probably created the ignition source, and that perhaps inerting the holes with low oxygen and high carbon dioxide concentrations from the machine's diesel exhaust was a potential solution. Considering the ventilation aspects of the problem, it was not clear If ventilation could be reliably established. If some degree of ventilation to the front of the mining head is achieved, it may combine with methane to bring the hole atmosphere from a rich, nonexplosive mixture to an explosive mixture. Furthermore, it may not prevent a dust explosion in such a mining configuration. Lack of access through the shafts of auger type mining machines further limits the ability to add water or air to cool bits to prevent an ignition source from developing. Either of these approaches would also be expensive. The process of mining coal In an inert atmosphere has been considered in the past, but to our knowledge, never implemented (Department of Interior, 1970). Clearly, implementation in underground mining would be more complicated. On a mine bench open to the atmosphere, however, adding inert gas to the mining head could provide a quick, feasible method to prevent explosions at auger highwall mining operations. Also the problem of how to move the inert gas to the cutting head of the machine had to be considered. Preventing explosions on auger mining machines using inert gas requires three primary considerations: first is the source of inert gas; second, placing the inert gas at the cutter head; and third, monitoring the hole atmosphere. Any gas source having an effective inert gas concentration of 34 volume pct or greater will prevent methane from Igniting (Zabetakis, 1965). Sources of inert gas considered for this application included liquid nitrogen, modified shipboard inert gas generators (for hydrocarbon shipping and transfer), jet turbine engine (Paczkowski, et. al., 1982), the auger's diesel engine and a gasoline engine. Operation cost, purchase cost and availability limited our testing to the diesel and gasoline engines. This work tested each engine, separately and combined. To ensure effectiveness, both company and enforcement personnel need to know how to monitor the condition of the inerted hole. Measurements at depth inside the hole are possible by remote sampling through rigid tubing, but this method is Impractical for routine monitoring. Continuous monitoring of the exhaust gas stream is an alternative. The U. S. Bureau of Mines evaluated an inert gas system at an auger mining operation at a surface mine near Owensboro, KY. Coal was mined from the Number 9 Coalbed in Henderson Co. KY. Tests were conducted in January and March of 1992.

Jan 1, 1993

By M. Fig, J. Brune, C. Strebinger, G. Bogin, J. Grubb

"Although it is known that explosive gas zones can form and sustain combustion in a longwall coal mine gob, a complete account of the interaction of the methane flame and gob remains obscure. The goal of this study is to examine the impact of several gob parameters such as packing orientation and void spacing. The impact of ignition location is also detailed. A series of experiments with methane flames were performed in a horizontal cylindrical quartz reactor. The reactor was tested both empty and packed with an obstacle wall consisting of spherical glass beads to investigate the impact of various gob parameters. Results demonstrate that methane burning velocity is sensitive to all parameters investigated, and most sensitive to packing density and ignition location. INTRODUCTION The explosion at the Upper Big Branch Mine in 2010 and several other underground longwall coal mine fires and explosions show that explosive gases can mix with fresh ventilation air creating explosive gas zones (EGZs). Investigative reports of these fires have found that EGZs are able to move from the gob and into the active longwall face, endangering workers and equipment [1]. Currently, researchers at the Colorado School of Mines are using computation fluid dynamics (CFD) modeling to predict the location and movement of EGZs in the gob and along the longwall face [2,3]. It is the goal of this work to validate combustion models [4] that include interactions of the flame and the gob for future incorporation into ongoing CFD modeling of EGZs [2,3]. Throughout the years, there has been significant research investigating how flames interact with obstacles and propagate through porous media [4,5,7-11]. Since there is limited access to the gob in a longwall coal mine (Figure 1), the orientation and size of rocks and void spaces within the gob is unknown. Experiments of a simulated gob have been performed in a large scale flame tube in order to investigate the effect of scale (Figure 2) [4,5]. However, the variation in rock spacing, rock orientation, and void location makes it difficult to determine the impact of each of these parameters on methane flame dynamics. This study aims at gaining a stronger fundamental understanding of gob parameters such as spacing, orientation, and ignition location on methane flame propagation. The results from this study will provide a basis for experimentation in larger explosion vessels and will be used to validate methane combustion models for incorporation into longwall ventilation models of EGZ movement [2,3,4]. BACKGROUND Researchers have been studying flame propagation across obstacles and porous media for many years using various fuels and experimental setups [4,5,7-11]. Experiments have been performed in horizontal chambers with both ends open [7], horizontal chambers that are semi-open [4,11], horizontal chambers with both ends closed [8], and vertical arrangements [9,10]. Due to the variation in experimental setups and methods of characterizing flame dynamics such as flame speed, peak overpressure, or burning velocity it becomes difficult to directly compare results. Flame speed is a property of the mixture and refers to the speed of the unstretched flame front normal to the direction of propagation. This study characterizes the flame by its burning velocity, which is the difference between the flame speed and the speed of the unburned gases just ahead of the flame front. However, some references use the terms flame speed and burning velocity interchangeably. In this study, a semi-open quartz cylindrical reactor was used to determine methane burning velocity, which was used as a basis for comparison to determine the impact of obstacle configuration on methane flame dynamics. The quartz reactor also has the unique ability to allow for flame visualization. These features allow for faster combustion model validation [4]."

Jan 1, 2017

By Victor F. Hollister

Introduction Trends of successful discovery technology and psychology emerge from a thoughtful study of various companies' exploration programs. These subjective patterns can be generalized into groups of factors for discussion. Here, for convenience, factors that influence exploration success are separated into management and geologic concerns. Most successful discoveries have a demonstrably favorable management combined with a technically competent geologic input. Both are required. But the management input is decisive. Management factors include the correct definition of management's role; cost of exploration; time needed for exploration; commodity selection; and the fostering of autonomy, creativity, and confidence in the geology department. Geologic factors include imaginative technical competence (field as well as academic), correct development and use of empirical exploration or prospecting models, and dedication. Success comes to those entities that are properly managed and have technological competence. A management team that directs a company's business has been compared to a dynasty. The dynasty lays out policy and follows up with appropriate action. In that management's power is pervasive, the term is appropriate. Management's role is, however, more important. Many examples can be cited where the geologic input was impeccable. But management somehow snatched defeat from the jaws of victory, and the exploration success was turned to a third party's profit. Management Factors Management's role can be broadly generalized to four parts. These are to identify the commodities it seeks, define its part in the exploration process, develop a functioning exploration department, and have the desire to succeed. It must have confidence in its geologists and delegate to them the authority and responsibility they need to operate successfully. Head office management cannot do the thinking for a field staff thousands of kilometers away. There is no substitute for confidence and delegation of authority. Successes came to those who had the freedom to act. Motivation is a management requisite. Management's role is to prevent destructive, internecine political battles within the corporate structure. Most large US mining corporations have well known histories of political strife that have damaged their exploration efforts. Management's role must, above all, include the desire to succeed. There are cases where management has been confronted with a commercial exploration success, but their reaction is to request additional study or exploration. Perhaps the problem of bringing a commercial find into production is beyond their capabilities. But a bona fide discovery sent back for additional work commonly is lost due to that management. The cost of exploration is a factor that management must accept. A variety of studies made during the past 40 years shows the cost per discovery to be $25 million, $38 million, $200 million, or even $290 million. These figures are derived by dividing the total exploration expenditure by the number of discoveries. However, successful management dynasties have a much lower cost per discovery during their management regime. Asarco, from 1948 through 1963, had one of the lowest cost discovery rates in the world. Duval Corp., from 1948 through 1968, had comparably low discovery costs. Placer Development, from 1955, was equally successful. Western Mining in Australia has had one of the longest lived dynasties associated with exploration success. Time is vital in exploration success. Most successful exploration case histories stress sufficient time in project exploration so that the target is well tested. A large target cannot always be adequately evaluated by a few holes (strat or concept testing). Serendipity helps in exploring large targets, but it best operates in a lengthy program. Numerous case histories include pleasant surprises. But these came mostly after the 10th hole. Commodity markets are important factors governing exploration success. Management's decision to explore for a specific commodity can doom its effort if that product suffers from severe oversupply. Unquestionably, progressive copper price increases from 1948 through 1968 helped convert marginal porphyry copper discoveries

Jan 8, 1985

By Donna L. Boreck

Introduction Coal has been mined in the western United States since the mid-1800s. The resource is abundant in the West. Despite recent economic conditions, it remains an important part of the nation's energy warehouse. Many of the seams that comprise the western resource base are thick, some exceeding 61 m (200 ft). Multiple, closely-spaced seams or thick coals that split into two or more minable seams are also common. Historically, subsurface development recovered from less than 15% to 50% of these deposits (Matson and White, 1975). This resulted in a substantial loss of inplace reserve due to the limited height that could be mined using the available technology. In an effort to increase future recovery from such deposits, the US Bureau of Mines analyzed the potential for incorporating three thick-seam mining methods into western coal mines. These methods are high-face longwall, multislice longwall, and longwall caving. They were developed in Europe and are being used to mine thick coal seams in Europe and Asia. One aspect that will determine their success in the US is the geology of the individual deposit; namely, are the methods adaptable to the geologic conditions characteristic of western coal? This paper analyzes some of the geologic factors that would affect development of thick or closely-spaced seams using these mining methods. Occurrence of thick and closely-spaced seams Since mining conditions and methods differ around the world, a thick seam is often defined as a seam whose total thickness cannot be extracted using the available equipment. In the western US, the maximum extractable mining height is about 4.3 m (14 ft). For this research, a thick seam was defined as a minable seam 4.6 m (15 ft) thick or more. Since one of the seams is usually lost using standard mining methods, closely-spaced or split seams were also addressed. These were defined as two minable seams 1.5 m (5 ft) thick or more separated by 9 m (30 ft) of interburden. Thick or closely-spaced coal seams are common in the West. Their importance has not been documented due, in part, to the methods used to measure resources. In the past, all reserves greater than 1.1 m (42 in.) thick for bituminous seams and greater than 3 m (10 ft) thick for subbituminous seams were grouped together and were differentiated only by rank. Further differentiation by seam thickness or minability was not done. For this reason, reserve figures for thick or split seams are difficult to determine. By analyzing available published resource data, Ferm and Muthig (1982) addressed thick seam resources. They estimated a resource of 90 Gt (99 billion st) of coal (16% of the Western resource base) in seams 4.6 (15 ft) or greater at less than 610 m (2000 ft) overburden. Yet, a later study of Pierce and others (1982) on one thick seam deposit in the Powder River Basin estimated a resource of 103 Gt (113 billion st). Pierce (1986) reported that the overburden reached a maximum of 731 m (2400 ft). The resources in this single deposit exceeded the 90 Gt (99 billion st) total projected for the entire western US by 12.7 Gt (14 billion st). Due to such differences, this author chose to look at reported occurrences of thick or closely-spaced minable seams in place of resource figures, to verify the need to research thick seam mining in the West. An occurrence was defined as an isolated site where a thick seam or two or more closely-spaced seams were reported. The occurrences were derived from published material - mostly mine descriptions, measured sections, coal exploration logs, and oil and gas logs. Due to time constraints, the reserves associated with each occurrence were not determined. All data points were random. The analysis was limited to occurrences in Colorado, Wyoming, and Utah. Although source material available to the author was limited to general coal summa-

Jan 3, 1988

By Ryne Goodnough

INTRODUCTION The Wyodak Mine is located in the northern Powder River Basin of Wyoming and is thought to be the oldest continuously operating coal mine in the United States, having recorded yearly production since 1923. The mine has expanded over its 80-plus-year history from an underground room and pillar operation to a modem surface snip mine. Currently, the mine feeds four on-site power plants using conveyors, has a filly automated truck load-out, and ships coal by rail to nearby Wyoming power plants. Annual production of 4.8 MTFT is accomplished on a single-shift basis with 53 fill-time production, maintenance and administrative personnel. In 1990 a decision was made to modernize the coal feed system to the power plant complex with modular conveying equipment. The project involved constructing coal storage silos, overland conveyors, feeder breakers and modular conveyors to follow the mining benches. Total project cost in excess of $25 million was used to construe or commission: A 2,150-TPH 48-inch overland conveyor with horizontal curve A 2,150-TPH 48-inch plant feed conveyor 13 shuttle conveyors, each 150 feet in length 2 front-end loaders equipped with large coal buckets 2 crawler-mounted feeder breakers with compatible discharge conveyor 1 high-lift shuttle conveyor with adjustable discharge height 1 high-angle conveyor 2 4,500-ton coal silos with automated truck load- out capabilities. Conceptually, the plan was to develop 33 MTONS of reserve adjacent to the plant complex and use front-end loaders to tram ROM coal to in-pit feeder breakers. The primary crushing would reduce coal to 6-inch minus and feed through a series of shuttle conveyors to an overland supply conveyor. The overland conveyor would feed the secondary crusher, and the crushed product would be moved to any of four storage silos using conveyors. The in-pit crushing and conveying system is a unique fit for the power plants and provided many interesting challenges for the coal mine to overcome. System integration, maintenance windows, equipment availability and the like had a major role in engineering the system to a power plant complex having no emergency coal stock- pile and limited plant storage. In crediting the designers and operators, the in-pit conveying system at the Wyodak Mine has delivered coal to the power generators since 1994 with little or no downtime. ENGINEERING CONSIDERATIONS Yearly production for the mine is based on 3.5 MTPY which requires about 1,550 TPH on an 8 hour, one-shift- per-day, 5-days-per-week basis. Considering efficiencies for starting and stopping, crew transport, loader trams, and operational delays, a nominal conveyor feed rate of 2,150 TPH or 72% system utilization was used in engineering design application. This ton-per-hour basis is used to size and commission the remaining components of the in-pit system. Coal quality requirements also played a role in equipment selection. The mine reserve grades vertically and coal from Upper and Lower benches needed to be mixed in any given proportion. This required equipment to be filly variable and capable of producing all or part of the 2,150-ton-per-hour requirement. Bisecting the 80-foot- high coal face for quality required construction of a high lift module capable of reaching a single overland conveyor 40 to 50 feet above the pit floor. Designers built a high-lift, adjustable and portable module specific for this application Having two bench systems capable of each producing the required feed for the power plants required computerized control processes to control on-line production. RSLinx, RSLogix, and RSView were chosen as the communication and control software, and a Data Highway Plus serves as the communication backbone. Each of the two in-pit benches are controlled with a data center equipped with Allen Bradley 5-40 processors. This

Jan 1, 2004

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

7.1 INTRODUCTION Subsidence measurements include surveys of surface and sub- surface movements and measurements and monitoring of surface structural damages. In this chapter the most commonly employed methods are discussed. 7.2 MEASUREMENT OF SURFACE MOVEMENT Surface movements involve two basic components, subsidence and displacement. The other five components (i.e., slope, curvature, strain, twisting, and shearing) are derived from the two basic components. Since all measurements are geometrical, they can be measured by common surveying techniques. 7.2.1 MONUMENTS The first step is to select the types of monuments or surveying stations. Various types of monuments have been employed. The simplest one is a paint mark on the pavement or concrete slab, although this should be discouraged because it is easily affected by artificial or environmental factors. Others use steel or wooden rods, 2 to 3 in. in diameter or square by 2 to 5 ft long, driven all the way down, flush with the ground. Both types of-monuments have no provision for frozen ground heave and both are tampered with easily. A more elaborate type is shown in Fig. 7.1 (O'Rourke et al., 1982). A rebar or iron pipe, 2 in. in diameter by 6 ft long is driven down to nearly flush with ground surface. The top 4-ft section of the hole around the pipe is enlarged to 1 ft in diameter and grouted with concrete. The most sophisticated type of monument is shown in Fig. 7.2 (Conroy and Gyannaty, 1983a). It consists of two hollow steel pipes. The inner I-in. pipe, 10 ft. long is enclosed by a 2-in. pipe at the upper 5-ft. interval. The gap between pipes is filled with foam to isolate the inner pipe from external environmental effects. The bottom of the inner pipe can either remain open or be sealed with a cap, depending on whether the ground is dry or wet. 7.2.2 MONUMENT ARRANGEMENT AND SURVEY LINES The monuments are installed strategically to form survey lines. Three basic types of monument arrangements are shown in Fig. 7.3. Figs. 7.3a and 7.3b are for single and multiple panels respectively; Fig. 7.3~ is mainly for research purposes with multiple survey lines both in longitudinal and transverse directions. This is extremely useful for defining the distributions of ground deformation, as shown in Figs. 2.10 and 2.11. Basically there are two types of survey lines: the whole basin survey line which extends across the panel width or length (e.g., lines R, R, in Fig. 7.3 a&b), and the half basin survey line which covers approximately half of the panel width or length (e.g., lines R, F in Fig. 7.3 &b). Survey lines are generally straight and linear. They should be located on the major crosssections of the subsidence basin. Survey lines must extend beyond the edge of the opening for a sufficient distance so that the edges of the subsidence basin can be determined accurately. The minimum distance from the edge of the opening must be [ ] where h = mining depth, [ ] = angle of draw, and [ ] = 5 to 7 times monument spacing for whole basin surveys, or 8 to 10 times the monument spacing for half basin surveys. There must be at least two controlling monuments at each end of each survey line. Controlling monuments must be located beyond the influence of underground mining. The spacing of the monuments ranges from 15 to 200 ft. The UK National Coal Board (NCB, 1975) recommended a spacing equivalent to 0.20 of the mining depth. Peng and Geng (1982) recommended that the maximum monument spacing be dependent on mining depths as follows:

Jan 1, 1992

By Vasiliki Founta, Andrew J. Whittle

"This paper describes the development of a 3D finite element model for predicting ground movements caused by construction of 7.1 m diameter twin bored tunnels for the Crossrail project in London using Earth Pressure Balance (EPB) machines. The model uses the commercial FE code, Plaxis 3D, to represent the face pressure, conical shield, grouting process and activation of precast segmental concrete lining systems through a set of boundary conditions that advance through the soil mass along a prescribed trajectory. Soil behavior is described using the Mohr-Coulomb soil model with input parameters calibrated from laboratory element tests. The analyses focus on the performance of the EPB tunneling machines in greenfield conditions beneath Hyde Park, where the tunneling occurs within deep layers of relatively uniform London Clay. The model predictions are in good agreement with surface and sub-surface vertical settlements measured at a well-instrumented section, but tend to overestimate the measured lateral displacements towards the tunnel. Ongoing studies are focused on the role of soil behavior and the approximations in FE model predictions of tunnel-induced ground deformations. Introduction Since their introduction in the 1970’s, closed-face Earth Pressure Balance (EPB) machines have become widely used for soft ground tunnel construction. The EPB design relies on a screw conveyor system to regulate the pressure of the excavated soil/spoil within the head chamber and hence control stability at the face of the machine. One of the key design issues in the application of EPB machines is to establish how control parameters, including the advance rate, face pressure and grouting processes (used to compensate for the tail void at the rear of the shield and to infill gaps between the precast lining rings and surrounding soil) affect and/or control the far-field ground movements. For closed-face systems, short-term deformations are associated with ground losses at the face, overcutting and ploughing of the shield and poor control of grouting in the tail void; while long-term deformations can occur due to consolidation and creep within the surrounding soil (and are closely connected to the seepage boundary conditions;e.g., Laver & Soga, 2012). The control parameters for advancing the EPB machine can have a significant effect on the magnitude and distribution of the far-field deformations. Therefore, analyses of the ground response to tunneling require accurate modeling of the soil stratigraphy and constitutive behavior as well as the construction process. Finite element (FE) methods have been used to simulate tunnel construction since the early 1980s, but only a few studies involved three-dimensional modelling of mechanized tunneling (e.g., Finno and Clough 1985; Bernat and Cambou 1999; Swoboda and Abu-Krisha 1999; Dias et.al. 2000; Melis et.al. 2002; Kasper and Meschke 2004; Möller 2006). In order to get a better understanding of the effect of the construction process and soil properties on the development of the ground deformations more comprehensive models of tunnel excavation and tunnel support are required in order to capture the 3D nature of mechanized tunneling and the effect of construction parameters such as advance rate, face and grout pressure."

Jan 1, 2016

By Leonard Harris

Good morning ladies and gentlemen. I would like to thank Hans von Michaelis for inviting me here today to talk to you on the subject of "How to Reduce Capital and Operating Costs at Heap Leaching Projects". The comments I have to offer are based on my experiences in gold heap leaching by Newmont Gold Company in Nevada, by Newcrest in Western Australia (formerly Newmont Australia), by Minera Yanacocha in Peru, by Penmont in Mexico, by Z­Mont in Uzbekistan, by the Hochschild Group in Peru and expe­riences in copper heap leaching by Magma Copper Company in Arizona and as a consultant on several other smaller projects worldwide. These comments are a mixture of technology, ideology, philos­ophy, strategy, logic and opinions and might be looked at by many of you as "one man's view". I like to look at them as "a view from the bridge". Let me add that it doesn't bother me that you may not agree with my comments and that I would be interested in your comments or criticisms at the end of this presentation. I don't intend to discuss the details of the mineralogical and metallurgical test work. I will assume, for this talk, that the test work has been conducted very carefully and that the ore in ques­tion has been determined to be heap or dump leachable. Let's begin with a couple of don'ts! ! First, "don't build the mill until you have a mine". This might sound to many of you as fundamental but believe me it continues to happen. The minable reserves should be well known and established as being economical to mine and leach. NPVs, ROis and IRRs are fine if you can be sure of the gold price you use in your calculations. The best method is to carefully estimate the capital cost and, most importantly, the operating cost per ounce of gold recovered which should include the repayment of the borrowed capital and the interest thereon. For example, if the operating cost under these conditions is $200 per ounce, you have a project. If it is $400 per ounce, walk away f om it. Incidentally, the same prin­ciple can be applied to projects involving other metals such as silver, copper, lead, zinc, etc. The second don't is - "don't be sheep". Don't climb on the bandwagon with respect to design and operation because every­one else does it a certain way. Keep an open mind, be versatile, look for change, look for every possible innovation for reducing capital and operating costs. Beware of those who will tell you "we tried that it won't work" or "it's too expensive" or "that's a crazy idea" , <' ''what do you know about mining - you are a metallurgist aren't you" or "what do you know about metallurgy - you are a miner aren't you" or "only geologists can handle this issue". Be careful about pigeon-holing people according to their basic degree and experience. In these days of low metal prices, we need to consider everybody's ideas, as crazy as some of them might seem.

Jan 1, 1998

By V. Rajaram

V. Rajaram&apos;s paper does not accurately reflect the status of Eastern oil shale development as it stands today. Today, there are numerous firms and research organizations pursuing development of the Eastern oil shale resource. Details of the current projects can be found in the symposium proceedings for the 1985 Eastern Oil Shale Symposium held in Lexington, KY, in November 1985. Additionally, the comparison of the Paraho and HYTORT processes is invalid because the HYTORT process design used it not an accurate representation of the HYTORT process. I will briefly address this point. It is disconcerting to see the author reference hydroretorting work conducted at the Institute of Gas Technology (IGT) (circa 1978) in the introduction, which indicates hydroretorting (the HYTORT process concept) yields of up to 250% of the Fischer Assay oil yield, and then turn around and base the remainder of the paper on the 1981 "Synthetic Fuels From Eastern Oil Shale Report," which depicts the HYTORT process as yielding only 115% of Fischer Assay. Indeed, work conducted at IGT to 1981 indicates commercial oil yields for the HYTORT process would be in the range of 200% to 210% of Fischer Assay. A more thorough literature search by the author would have yielded a 1981 publication by Schora et al., entitled "Update on the HYTORT Process" presented at the Symposium on Synthetic Fuels From Oil Shale in Nashville, TN, October 1981. This paper thoroughly discusses the shortcomings of the referenced study with respect to the HYTORT process. For the interested reader, I can also recommend a June 1984 report entitled "An Economic Comparison of Five Process Concepts for Using Eastern Oil Shale," published by Los Alomos National Laboratory (LA-10106-MS, Parkinson et al., NTIS No. DE84-015981). This study applies a realistic HYTORT design (circa 1982) and indicates that HYTORT is the most econom¬ical method of processing Eastern oil shales (about $20/bbl less than Paraho). Additionally, completion of the HYTORT feasibility study in June 1983 by Phillips Petroleum Co., Bechtel Group Inc., HYCRUDE Corp., and IGT has resulted in development of designs that will make the use of HYTORT on Eastern oil shales even more economic. HYCRUDE Corp., a second-tier subsidiary of IGT, is involved in commercialization and licensing of the HYTORT process and is active in efforts to develop the Eastern oil shale resource. As such, I am disappointed to see outdated material that has the potential for adversely affecting development of Eastern oil shale resources published in MINING ENGINEERING. I can only hope that this response will serve to mitigate any negative opinions that may have been formed. Today, activity in commercializing Eastern oil shales dominates the oil shale scene in the US and indicates a realization of the potential for these shales. Reply by V. Rajaram I appreciate the updates on the HYTORT process provided by R.C. Rex, Jr. I hope that Hycrude&apos;s work will lead to the funding of a pilot plant to demonstrate that yields of greater than 200% of Fischer Assay can be achieved in a commercial plant using eastern US oil shales.

Jan 1, 1987

By Louis J. Sousa, Elizabeth H. Yaremchuk, Annette P. Graham

Introduction Responding to Congressional inquiries regarding the purchase of a number of major domestic mining and metals companies by foreign firms, the US Bureau of Mines examined trends in foreign direct investment in the US. mining and mineral processing industries1. "Foreign Direct Investment in the US Minerals Industry" analyzes the extent of foreign investment in several major mineral commodity industries. It identified the countries of origin of foreign investment in US mineral assets. The study also described several reasons for the growth of foreign investment in US minerals and discussed some potential implications of this activity. Foreign investment trends in the economy and minerals For the economy as a whole, between 1977 and 1985 the number of US affiliates of foreign investors more than doubled - from 4046 to 9824 - as did employment at these affiliates - from 1.2 million workers to 2.9 million (Table 1)2. During this same time period, the total value of assets of all US affiliates throughout the economy rose from $239 billion to $736 billion (1985 constant dollars). In the domestic minerals industry, foreign investment also grew substantially during that same time as the number of US minerals-related affiliates increased by 74% - from 125 to 217 - between 1977 and 19853. During the same period, employment at all foreign-owned affiliate mineral operations in this country increased by 78% and totaled 198,000 workers at the end of 1985. Parallelling the growth in the number of and employment at foreign-owned US mineral and metal operations, the total value of US mineral assets owned by foreign firms (or individuals) has nearly doubled since 1977 and amounted to $30.9 billion at the end of 1985. The rate of increase in foreign investment in US mineral assets was slightly higher in the metals industries than in the nonmetallic groups. Foreign investment more prevalent in minerals Perhaps a more useful way of evaluating the growth in foreign investment is to analyze growth in the "intensity" of foreign investment - the proportion of total US industry assets held by foreign investors. Although insufficient data on total industry assets prevented the development of such a measure, employment data provide an indication of relative differences in the intensity of foreign investment among the mineral industries and other industries. For example, as noted in Fig. 1, the 198,000 minerals industry workers employed at US-affiliate companies in 1985 represented 12.7% of total employment in this sector of the economy. In comparison, for the mining and manufacturing sectors of the economy as a whole, 7.8% of all workers were employed at US-affiliate firms in 1985. For the total economy, 2.7% of the entire civilian employed workforce worked at US-affiliate firms that year. Using employment as an indicator, foreign investment has been more prevalent in the minerals industry than in most other industries. About one worker in eight in the minerals sector was employed at a US-affiliate firm in 1985. In comparison, for the goods producing sectors of the economy - all mining, petroleum, and manufacturing industries - about one worker in 13 was employed at a

Jan 8, 1988

By John D. Morgan

Introduction The US Bureau of Mines&apos; (USBM) world reserve/consumption ratios (Table 1) indicate that, if the world is relatively peaceful in the next two decades, there should be ample world supplies of minerals to permit rising standards of living for increasing world population. But it must be remembered that most mineral reserve estimates are conservative and that normal mining practice is to develop a ton of ore reserve for every ton mined. It should be noted that "reserve," as used in this paper follows the definition given in US Geological Survey (USGS) Circular 831, 1980; "that part of the reserve base which could be economically extracted or produced at the time of the determination." In addition to accurately determining the geologic parameters of mineral deposits, a judgment as to whether that deposit is a "reserve" per se involves consideration of many other factors. These factors were recognized nearly a century ago by a well-known mining engineer and later President, Herbert Hoover. In "Principles of Mining," 1909, Hoover wrote: "Unfortunately for the mining engineer, not only has he to weigh the amount of risk inherent in calculations involved in the mine itself, but also that due to fluctuations in the value of metals. If the ore is shipped to custom works, he has to contemplate also variations in freights and smelting charges ...In a free market, the law of supply and demand governs the values of metals as it does that of all other commodities. So far, except for tariff walls and smelting rings, there is a free market in the metals under discussion. The demand for metals varies with the unequal fluctuations of the industrial tides. The sea of commercial activity is subject to heavy storms, and the mine valuer is compelled to serve as weather prophet on this ocean of trouble. High prices, which are the result of industrial booms, bring about overproduction, and the collapse of these begets a shrinkage of demand, wherein consequently the tide of price turns back." Current supplies and use There have been ample supplies of most mineral materials to permit several-fold increases of world production of common major mineral based minerals (steel, aluminum, copper, and cement) over the past three decades. Motor vehicle production is a major consumer of mineral materials. However, in the last decade, down-sizing to facilitate improved fuel efficiency and reduce harmful emissions has reduced the weight of the average US-made automobile 15%, to 1.5 t (3200 lbs). Also in the US, there are 92 million dwelling units, or on average, fewer than three persons per dwelling unit. Construction is another major consumer of materials in the industrialized developed countries. It will also be a major consumer of materials worldwide as less developed nations seek to improve their infrastructures by adding roads, bridges, railroads, airfields, ports, and housing. Fortunately, a large number of traditional common materials, many of mineral origin and also many of agricultural origin, are readily available for construction. Traditional construction materials such as steel, aluminum, copper, and cement, are being replaced in many applications by engineered plastic and ceramic

Jan 4, 1986

By Steven J. Stokowski, Frederick M. Bodycomb

This chapter deals with the use of industrial minerals in insulating materials used to control our thermal and acoustical environment. There are numerous products on the market used for thermal and acoustical insulation; they consume substantial quantities of a variety of industrial minerals. Following is a brief review of the theory and function of insulating materials. Acoustics is the science of sound, and architectural acoustics deals with sound in buildings. If this definition is broadened to include transportation vehicles, it is this end use for which acoustical insulations are primarily manufactured. Sound is defined as the auditory sensation in the ear, or the disturbance in a medium which causes this sensation. Acoustical insulation is used to reduce or eliminate noise, defined as unwanted sound. Noise control may be accomplished by the reduction of sound radiation at the source, by utilizing sound reducing construction methods such as staggered studs, etc., to control sound transmission, or by using sound absorbing material on walls, ceilings, and floors (Rossing, 1985). Acoustical insulation functions by absorbing the energy in sound waves in a porous material. As the sound waves penetrate the pores, they are dissipated by reducing the amplitude of vibration of the air molecules by contact with the pore walls, with subsequent conversion of the sound energy to heat energy. Acoustical insulation is generally highly porous, 1.3 cm or greater in thickness, and has interconnected pores. Acoustical insulating materials include fibrous vegetable or mineral matter and cellular organic and inorganic material, such as natural or manufactured foams (Sabine and Moulder, 1979). Acoustical materials are most commonly porous boards and tiles, which are often composite materials with perforated facing. Roof insulation board and lightweight concrete can also contribute to the absorption of noise. Thermal insulation is defined as material used to control the flow of heat. It may be used for heat control from low cryogenic temperatures (below -100°C) to in excess of 2 200°C for applications such as ablative shields for spacecraft. Heat transfer occurs by conduction, convection, or radiation. Conduction is the transfer of heat without the movement of the conducting medium, as through a metal. Heat convection through a liquid or gas takes place by movement of the medium. Forced convection is the basis for heating and cooling equipment, utilizing pumps or blowers to transfer the thermally conditioned fluid. Free or natural convection occurs due to density differences in the fluid. Radiation is the transfer of energy in space (Eckert, 1985). Conduction of heat through a solid is reduced by insulating the body with foams, or fibrous or small celled granular material. Heat transfer through a gas (convection) is controlled by creating many small pores which inhibit the movement of the fluid, substituting a gas of low thermal conductivity, or evacuating the space. Heat radiation can be reduced by the use of materials that reflect or absorb the energy (Glaser, 1967). Thermal insulating materials may be vegetable or mineral fibers, organic or inorganic particles, or foams with small pores, generally used to form a low density thermal barrier. They may be blocks, poured lightweight cementitious materials, bricks, etc.

Jan 1, 1994

By William A. Vogely, Robert T. Deacon, Walter J. Mead

Oil and gas together are the most important energy sources consumed in the United States. In 1983, 67% of total energy consumption was represented by these two resources (43% was oil and 25% natural gas), while coal accounted for only 23% of U.S. energy use. All other sources (hydroelectric, nuclear, geothermal, wood and other waste products) accounted for only 10% (U.S. Department of Energy, 1983, p. 1). In this chapter we address the issue of regulation in the oil and natural gas sectors of the U.S. energy industry. In addition, we analyze the cartel characteristics of the Organization of Petroleum Exporting Countries (OPEC). If OPEC is an effective cartel, then U.S. oil as well as substitute energy prices, production, and consumption will be affected by cartel action. Further, as the nation learned in the 1970s, major changes in oil prices produced major disturbances in other sectors of the U.S. and world economies. Consequently, it is important to determine whether the roughly ten-fold increase in nominal prices that occurred in the 1970s was the result of cartel action, the result of normal economic forces adjusting to the fact that the world was running out of cheap oil, or some combination of the two. Furthermore, the presence of OPEC- associated oil price increases is related to regulations that were imposed on the energy sector during the decade of the 70s. THE RATIONALE FOR GOVERNMENT INTERVENTION Economists have traditionally judged the state of an economy to be efficient if it is impossible to improve the welfare of any one member of society without harming someone else. Any economy that satisfies this condition is said to be Pareto efficient, after the Italian economist Vilfredo Pareto who first gave rigorous attention to such questions (see Chapter 4.10). It is easy to see why an economy that fails to satisfy this condition could not be efficient; by definition, it would be possible to alter the allocation of resources in a way that improves everyone&apos;s welfare.&apos; Much of the appeal of this weak efficiency criterion is that it avoids comparisons of levels of well being among different individuals. The cost of such generality, however, is that in any given economic system a wide array of different Pareto efficient states will typically be attainable. In the simple Robinson Cursoe economy of the undergraduate textbook, for example, efficiency could just as easily be attained in the case where most of the island&apos;s resources are owned by Friday as in the case where they are under Crusoe&apos;s control. However, the distribution of welfare among the two inhabitants would obviously be quite different in the two situations. Such equity issues cannot be settled on objective or scientific grounds. To decide which distribution of welfare is socially "best" an explicit value judgment is needed. It is useful to keep in mind the preceding distinction between efficiency and equity issues when analyzing the role of government in a market economy. Decentralized market processes will not necessarily result in a distribution of welfare that society considers just. For this reason a potential role for government lies in the redistribution of income among individuals. In some circumstances, however, market pro-

Jan 1, 1985

By J. Boisvert, E. Daniels, C. Deutsch

"INTRODUCTION Conventional mine planning is performed on a single resource model at a selective mining unit (SMU) scale deemed appropriate for the deposit and mining method. Estimation methods such as kriging and inverse distance, commonly used to construct a single model, are susceptible to histogram smoothing (Rossi & Deutsch, 2014). This can be mitigated by limiting the number of composites per estimate, therefore correctly reproducing the distribution of estimates (Boisvert & Deutsch, 2012). Search limiting techniques remedy histogram smoothing at the cost of introducing a problematic conditional bias (Isaaks, 1999) and introduces even greater spatial smoothing. Localization is an alternative, offering histogram reproduction through post processing of more robust probabilistic modeling techniques. A single localized model at the SMU scale is desirable. The correct histogram can be reproduced and a single model allows for the use of conventional mine planning and resource evaluation techniques. Despite the advertized benefits of localization, the necessary reliance on a larger panel scale as a middle step in the localization process yields unsightly “edge-effect” artifacts (Boisvert & Deutsch, 2012). Two approaches to artifact reduction are presented here. The first is a straight forward optimization approach designed to minimize an objective function that penalizes artifacts including panel edge discontinuities to generate a model free of panel edge-effects. The second approach redefines a panel in a less conventional fashion as a randomly chosen set of SMUs throughout the domain. This method produces a model void of any regular panel shape resulting in an artifact free model. Artifact reduction minimizes the obvious “edge-effect” issues of localization but local precision issues described by Boisvert & Deutsch (2012) persist. Localization is not a replacement for quantified uncertainty for comprehensive risk analysis and resource evaluation. LOCALIZATION Initially developed with Uniform Conditioning in mind, localization collapses a distribution of local uncertainty at a panel scale to an SMU scale model for mine planning (Abzalov, 2006). This process has been extended to Indicator Kriging (Hardke, 2011), Sequential Gaussian Simulation (Boisvert & Deutsch, 2012) and MultiGaussian Kriging (Daniels and Deutsch, 2014). The localization process is performed in a similar fashion regardless of which technique is chosen to create the prior model of uncertainty. Methodology There are three scales of importance considered in the localization process. The point scale, otherwise known as the data scale, is the smallest and is the scale at which experimental data is collected. The SMU or block scale is the familiar scale at which mine planning and resource evaluation takes place. Lastly, the panel scale is larger and contains a number of SMUs. Each of the three scales is illustrated in Figure 1."

Jan 1, 2015

By Sadatoshi Ohmori, Karen Shinoda, Nobuharu Isago

Method of tunnel excavation is generally classified such as full-face excavation, bench-cut excavation, diaphragm with center pillar excavation, center drift advancing excavation and so on. These excavation methods should be selected properly in terms of ground condition, the area of tunnel section, the arrangement of construction. Center drift advancing excavation method in mountain tunnel construction, is often applied under quite weak ground condition, prior to the main tunnel widening excavation. Recently, the advancing drift is for the excavation of extreme larger section in main tunnel to confirm the stability of face. In addition, we make advancing deformation occur in drift when the construction was done in poor ground like squeezing and swelling ground, and the force occurred in main tunnel was expected to reduce by the effect of ‘dodging’ for support structure. Mechanical relation between drift and main tunnel has been mainly grasped on past experiences in Japan. However, the characteristic of tunnel enlargement was partially discussed by using the three dimensional analysis and the result was grasped by past experiences on the basis of each tunnel construction. It is considered that the natural ground stress is normally released as the advance displacement, but it was released after the main tunnel widening, causing a displacement and deformation increase. Up to now, the construction practice has shown the reduced displacement during the main tunnel widening excavation by the drift, and the numerical analysis agreed with above observation. However, there is no report found that the displacement and deformation at the time of widening excavation of the main tunnel become larger in case of a drift application. In Kyusyu area, western part of Japan, the northern part of Yoshinomoto tunnel was applied an advancing bench-cutting method for a center drift for the purpose of obtaining the geological information for support selection of the main tunnel in widening excavation. The shape of center drift was a perfect circle with a diameter of 4.0 m or 6.0 m and the same temporary support regardless of the geological situation. As a result, the displacement and deformation of the main tunnel after widening excavation were larger than the section where the center drift was not applied. Furthermore, the displacement and deformation of the main tunnel after its widening excavation was considered larger in the section where the cross-section of the center drift with 4.0 m diameter was applied than one with 6.0 m. Therefore, the center drift with a high rigidity support structure had the effect of suppressing the advancing deformation prior to the main tunnel widening excavation.

Jun 13, 2021

By R. C. Gilmore, A. Juganda, Jr. Bogin, S. Saki, S. A. Lolon, J. F. Brune, Jr. Zipf, J. W. Grubb

"Methane-air mixtures form explosive gas zones (EGZs) in underground longwall coal mine gob ventilation systems. Such EGZs have caused a number of fatal mine explosions, including the 2010 disaster at the Upper Big Branch mine, where 29 miners lost their lives. Researchers at the Colorado School of Mines use Computational Fluid Dynamics (CFD) modeling to predict EGZ locations. In this paper, a model of a bleeder-ventilated gob system includes two adjacent panels, an active longwall and a mined-out gob. Boundary conditions for the simulations match statutory ventilation conditions for methane concentrations and air flow rates at common measurement points throughout the mine. The modeling results predict the persistence of EGZs in the gob that may compromise the effectiveness of the bleeder ventilation system. INTRODUCTION Mine operators must maintain statutory air flow and air quality requirements at various locations throughout the mine ventilation network. U.S. regulations generally require mine operators to establish bleeder ventilation systems surrounding longwall gob areas (30 CFR §75.334.) Gilmore et al. (2015) documented that explosive gas zones (EGZs) exist within bleeder-ventilated gobs and may extend into the bleeder entries that must be examined weekly, presenting an immediate fire and explosion hazard to mine examiners. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) under contract 200-2009-31409, researchers at Colorado School of Mines have developed a tool for modeling gob air quality using Computational Fluid Dynamics (CFD). This CFD model is capable of examining a wide range of longwall mine ventilation systems. Marts et al. (2014a, 2015) studied progressively sealed gobs with U-type ventilation and using a back return. Saki et al. (2015) examined the impact of gob ventilation boreholes and face air quantity effects on tailgate methane concentrations. Gilmore et al. (2014) modeled bleeder-ventilated gobs and Gilmore et al. (2015) studied the effects of bleeder regulator settings on EGZ volume and locations in the gob. CFD studies for progressively sealed gobs were generally carried out using 5000 ft (1500 m) panels because the gob atmosphere remains largely unchanged from about 500 m (1,500 ft) inby the face. A modular meshing methodology (Gilmore, 2015) permitted researchers to extend bleeder models to 10,000 ft (3050 m) to include the full extent of bleeder entries. This paper further expands the bleeder CFD model to study the gob atmospheres of two adjacent longwall panels, each 10,200 ft (3100 m) in length, with the active face located 6,700 ft (2040 m) from the startup room."

Jan 1, 2016

By V. S. Tadsen

Today, man is able to probe space because of technological advancements including the ability to control certain combustion reactions very precisely. The recent adjustment of the attitude of Skylab by radio command from earth is an excellent example of such control. It is strange, and indeed unfortunate, that very little is known about the mechanism of combustion of pulverized coal, the primary fuel for rotary kilns. The selection of a coal for direct pulverized firing of a rotary lime kiln may be determined by trial and error, persistence of sales personnel, proximate analyses, grindability, or apparent BTU cost. Occasionally, the only question asked is, "How much lime will it make?" To study the behavior of a particle of coal in the combustion stream of a rotary kiln is most difficult. We must, therefore, discuss the general mechanism of combustion of pulverized coal, and relate this mechanism to the selection of a proper coal for a rotary kiln. The classic three T&apos;s -time, temperature, turbulence -must be enlarged upon for a better understanding of the problem. Pulverized coal occupies only 0.01 per cent of the volume of air required for its combustion. This mixture behaves like a gas and the general laws governing the movement of solid particles in gasses are in effect. The differential velocity between air and coal particles depends on forced and natural convection, diffusion, and the length of time each particle is in the combustion space. As a particle of coal absorbs heat from its surroundings, it begins to give off volatiles". These gasses ignite as their kindling temperature is reached, and burn readily because of the excess oxygen immediately available. Combustion proceeds at this stage by the outward diffusion of gas from the coal particle into the surrounding oxygen-rich envelope. We could say combustion at this stage represents a small coal particle surrounded by an envelope of volatiles burning at their point of contact with sufficient oxygen. This release or expulsion of gasses from the coal may result in exfoliation or disintegration of the coal particle. If this occurs, and it is desirable that it should, it will accelerate the final stages of combustion. The escape of volatile material from the particle of coal and its subsequent combustion will cause increased turbulence around that individual particle. Ignition is maintained by radiation from gasses and solids in the combustion system, and most importantly, re-radiation from the kiln refractories and the process load.

Jan 1, 1978

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sandblasting agent, as a premium-grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. Staurolite is produced by E. I. duPont de Nemours and Company as a coproduct of titanium mineral production in Florida, where it was first recovered on a commercial scale in 1952 from the Pleistocene sand deposit known as Trail Ridge. At this deposit it comprises about one-fifth of the heavy mineral suite, the principal other heavy minerals being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and other nonconductive silicate heavy minerals are separated from the conductive titanium minerals on high-tension electrostatic separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total process, 200 t of raw sand yield 7 t of heavy mineral concentrate from which about 1 t of staurolite is recovered. The staurolite concentrates have the characteristics given in Table 1. Staurolite concentrates are sold in three grades having the size distribution of subrounded grains shown in Table 2. All three grades are used in sandblasting for cleaning metal, for paint removal, and for cleaning masonry buildings. Staurolite compares favorably with lower priced abrasives, such as boiler slags and silica sand, in applications where the abrasive is used only once and is not recovered and recycled. Because it is hard, fine, clean, and dense it can reduce blasting time, and less material is required to clean a specific area. Compared to higher priced abrasives such as aluminum oxide and garnet, which are recycled, staurolite costs significantly less per kilogram and cleans at equal or faster rates. Its breakdown factor, which is a measure of recycling performance, is intermediate between those for aluminum oxide and garnet. [ ] [Tables 3 and 4] show the blast cleaning performance of the three staurolite grades compared to other abrasives. [Table 5] compares the longevity of premium priced abrasives during recycling. [Table 6] shows a cost comparison between silica sand and staurolite. Fringe benefits claimed for staurolite&apos;s use as an abrasive are: 1. Good flow properties and freedom from the lumps or slivers found in silica sand or boiler slag abrasives. 2. Low dusting affords good visibility, permits faster working, and reduces cleanup problems. 3. Heated storage is not required during freezing conditions, because the mineral is nonhygroscopic.

Jan 1, 1994

By Geno Saccomanno

INTRODUCTION Cancer of the lung in uranium miners has been reported by many authors. In fact, it has become a most popular subject for comment by environmentalists, health physicists, and newspaper writers. I believe it appropriate for me to discuss cancer of the lung in uranium miners in a general way commenting briefly on etiology, incidence, tumor cell types, and particularly, tumor development and treatment. Cytological development of cancer in its incipient stages, particularly the in situ stage, relates to potential cure with photoradiation, early diagnosis, and treatment. Our observations of the cytological response to this modality of diagnosis and treatment will be discussed briefly since this area will also be covered by Doctor Balchum. The cause of lung cancer in uranium miners is primarily due to two carcinogens; cigarette smoking and radon daughter radiation. Cigarette smoking has continued at the same intensity over time among uranium miners; about 60% of the miners are cigarette smokers and 40% are non-smokers. Radon daughter exposure to the uranium miner has varied from mine to mine, but over the last 20 years has been reduced to a minor fraction (.3 WL) of the level that prevailed in many of the mines during the 1950-1960 era when many of the miners were exposed to more than 10 WLM. Sputum samples have been examined on as many uranium miners as responded on the Colorado Plateau since 1956. Autopsy studies were done whenever this was permissible. In some instances, only tissue from a biopsy of a node or lung was available for study. Smoking histories were also taken. Approximately 200,000 sputum samples were examined and histological examinations of lung lesions were made from 312 cases. METHODS The method of sputum cytological collection and preparation was reported previously. I The lungs were fixed with formalin and prepared for sectioning by Dr. Oscar Auerbach with his block-section method. RESULTS Three-hundred-twelve lung cancers from uranium miners were examined. The tumor types and the age at death for each type, smokers and non-smokers, are given in Table #1. The incidence of the tumors in the smokers and non-smokers is given in Table #2. The incidence of small cell carcinoma of the lung has decreased from an incidence of 76% of all the lung cancers found in uranium miners to 22% of these lesions (Figure #1). The decrease in incidence of this tumor is probably due to decreased exposure to radiation in the mines.

Jan 1, 1981

By Dr. -Ing. Rainer Alles

Introduction Belt conveyors usually run in a straight line. The correct alignment is a major criterion for reliable functioning and optimum running properties. Any misalignment of the conveyor, especially mistracking of the belt, can have many negative effects. As a consequence of this, damage can occur on the belt and conveyor, some material can he thrown off at the edges and serious running problems can arise. In the worst case the belt can come off its supporting structure so that operations are brought to a halt. The absolutely straight alignment of a belt conveyor is actually impossible so that on closer observation every belt conveyor contains more or less sharp curves. Whereas on non-movable conveyors the deviations from the straight can he kept within the range of practical measuring accuracy by careful installation, movable conveyors in surface mining or belt systems in difficult terrain often contain curves that are easy to see with the naked eye. Below ground, too, alignment cannot always achieved to a desirable extent or is changed by geological faults over the years. Despite these unwanted curves, most belt conveyors perform their function reliably. In view of the belt tension, the belt tends to take the easiest path. This in general is the shortest distance between the pulleys on which the belt is tensioned and bent. This means for example that for a curve radius of 10,000 m over a flight of 100 m the greatest deviation from the ideal line is as much as 12 cm. And a figure of this magnitude cannot normally he accepted. In such cases, use is made of guide devices to properly train the belt if it doesn&apos;t center itself anyway. If it&apos;s possible to control the belt position over such unwanted curves. it can also he expected that the belt tends to follow the desired curved path within certain limits. I&apos;d now like to cite a few examples to illustrate the ways and means of guiding a belt conveyor in curves. Cost-effectiveness The advantages of belt conveyors, in particular for longer conveying distances and mass flows have been known and undisputed for some time. However, there are often obstacles standing in the way of the concept of straight routing. If a belt conveyor is to bypass elevations or existing buildings or to follow the seam of underground deposits or a predetermined path, then substantially tighter radii and longer curves are desirable or necessary.

Jan 1, 1993