Search Documents

By D. M. Wyslouzil

Conditioning, in the conventional sense, means providing sufficient agitation and contact time for the reagents to react with the minerals in the ground ore. High intensity conditioning (HIC) on the other hand, as described in this paper, recognizes the need to exceed this minimum power input over a suitable length of time to induce aggregation of the finest size fraction. Time alone is not sufficient to achieve aggregation. The threshold minimum power input, kW/m3, depends on many surface properties of the fine particles and can vary considerably. In addition, the mechanical aspects and the chemical conditions must be matched to achieve good aggregation. Treatment of complex sulphide ores, requiring fine grinding for liberation, offers a large field for the application of HIC. Improved flotation rates and enhanced selectivity are some of the benefits that can be expected. This unit operation has now reached the level of commercial application. Lakefield Research considered HIC not from a fundamental point of view but as a means of solving difficult mineral processing situations arising in actual operating plants. This paper summarizes the effects of the various chemical reagent combinations that had been applied to promote faster, more selective flotation, higher mineral recoveries and cleaner separations, using HIC.

Jan 1, 1995

By Charles C. Y. Chen, Duane R. Skidmore

Batch leaching of Ohio #1, Ohio #4A and Ohio #5 coals was conducted with the thermophilic. sulfur, oxidizing microorganism: Sulfolobus acidocaldarius. Four different size fractions of each coal, with median sizes of 508, 200, 90, and 49 microns, were subjected for 10 days to leaching in a 5% coal-water slurry at 72°C and a pH of 2. Release rates and extent of sulfate and iron I1 and I11 ions from the coals during the leaching process and distribution of sulfur forms (sulfate, pyritic and organic) in the coal samples before and after treatment were determined. Data indicated that Ohio #1 coal, with an initial sulfur content of 0.6%, showed no significant changes with leaching in total sulfur content or forms of sulfur. The Ohio #4A coal, with initial total sulfur content near 5%, yielded product, for sizes below 200 microns with 90% reduction of pyritic sulfur while the extent of organic sulfur removal varied with coal particle size. Results similar to those for Ohio #4A were observed on the Ohio #5 coal, which had an initial total sulfur content of 3% and a final sulfur content near 1%. The findings were interpreted in terms of basic biological, chemical and physical mechanisms.

Jan 1, 1989

By Claus Becker

Waterbearing, cohesive or non-cohesive grounds with glacial stone deposits are found very often in Europe. The problem consists of destroying the boulders and supporting the face simultaneously. At the example Grauholztunnel Bern ( outer diameter 11,60 m ) the theoretical attempt of solutions for the big machines is described: destroying of the boulders with roller discs, hydraulical support of the front. The problem of coming out of stones of a certain size from the surrounding matrix will be discussed. Further diminishing to the size that can be handled by pumps is executed by a crusher, situated in the center of the machine. At the same example the theoretical attempt for headings in cohesive soil with stone deposits are shown. Surface structure of the cutting wheel and working chamber as well as controllable current movements are the solution here. The danger of clogging discs and stone crusher has to be encountered by right positioning of the tools and jetting nozzles. At the example Sewer MoosstraBe Salzburg the same problems are discussed for the Mikro-Tunnels. The pipe-jacked sewer lines have outer diameters from 485 and 805 mm. With this method, the stones have to be holed through. The wear of the cutting tools determines the [ ]

Jan 1, 1989

By Michael G. Nelson, Dot J. Helm, Edmond C. Jr. Packee

Under a Section 319 Water Quality grant from the U. S. Environmental Protection Agency, a working group of government agencies, mining industry representatives, and University of Alaska researchers undertook reclamation of an abandoned mine site on Birch Creek, near mile 101 of the Steese Highway. Stream hydrology, water quality, and the extent and nature of natural revegetation, were measured before the site was then recontoured to decrease the bedload deposition and bank erosion of the streams. Methods for stabilization of streams and rivers appear to have much in common with those for locations further south, but are subject to complications unique to the North, such as the formation of aufeiss, and to a lack of accurate climatological data. Natural revegetation appears to be possible for most northern placer mine sites. However, it may take place more slowly than required by public perception. Preliminary data indicate a surprising lack of nutrients in the floodplains of mined areas. Natural revegetation may be enhanced by selective planting of grasses and willows, which will contribute variously to soil quality, bank stabilization, and short-term appearance. Monitoring of hydrologic and water quality data, and of natural and artificially placed vegetation will continue at the .Birch Creek site through the summer of 1995,

Jan 1, 1995

By J. A. Procarione, M. K. McCarter, Bradley C. Paul

A numerical technique is described which can be used to model the quantity and distribution of air flow through broken rock. The method can also describe gas concentration and temperature distribution. A computer code implementing the numerical approach was developed to assist in determining the feasibility of a proposed modified in-situ leaching method for extracting copper from sulfide porphyry deposits. This mining method requires air to be forced through cells of rubblized ore. The flow serves to supply oxygen for the leaching reactions and to dissipate heat that would other-wise build due to the exothermic reactions. The method substitutes the Carman equation into the Laplace equation. The solution of the resulting non-linear formulation is done on a finite difference grid using SOR with iteration improvement of coefficients. This procedure yields the required air flow pattern and pressure drop. An equation for advection with absorption is then solved over the same grid using explicit schemes to yield oxygen concentration. Finally, a similar technique is applied to the convective heat transfer formula to yield the temperature profile. The model is potentially applicable to such mining problems as the prediction of leakage through caved ground, the prediction of methane concentration in gobbed ground, and the prediction of heat build-up in caved workings.

Jan 1, 1989

By D. Gärtner, A. Oster

"""Operational excellence"" provides a sound foundation for RWE Power AG's three strategic pillars (innovation, expansion and organic growth). The maintenance and development of operational excellence in lignite mining operations at RWE Power is supported by the Continuous Improvement Process (CIP) ""immer:besser"" (getting better). Obtaining cost reductions with the aid of the CIP as a kind of value-adding self-renewal process to ensure competitive lignite mining operations and lignite-based electricity generation forms the basis for further increases in profitability and growth. Since the beginning of the 1990s, RWE Power has carried out a multitude of re-engineering projects focusing on the efficient shaping of processes with the assistance of external consultants to enable the Company to cope with the considerable need for change by swiftly implementing major efficiency levers. These also include the required adaptation and development of the organization. Since 2004, the Continuous Opencast Mine Improvement Process (""KVT"") has enabled the mines to tap significant cost reduction potential by virtue of their own strength. But there is another issue that has come into focus: the development of performance enhancement options. In 2006, the ""KVT"" process, piloted in the opencast mines, was included in the RWE Power-wide immer:besser (i:b) programme (Figure 1)."

Jan 1, 2011

Semiautogenous (SAG) ball mills are being increasingly used today for the coarse grinding of a range of ores, including gold, copper and iron. Larger mines are demanding mills with larger throughputs. This has led to some remarkable developments in mill diameters and installed powers. Conventional design principles - mills with trunnion bearings - have reached their limitations. This article describes one SAG mill with a slide-shoe arrangement and Krupp Polysius' Combiflex twin drive. In August 1997, the world's largest SAG mill with a slide-shoe arrangement was commissioned in Queensland, Australia, operating as a wet mill. The inside diameter is 10.4 x 5.1 m (34 x 17 ft) effective grinding length. The 1.36-ktlh (1,500-stph) SAG mill is driven by two Combiflex drives (twin drives with 2 x 5,500-MW or 7,375-hp installed motor power) in conjunction with a girth gear (outside diameter 11,890 mm or 468 in.). Commissioning of the SAG mill was completed with no notable technical difficulties. The plant runs continuously except for planned maintenance stoppages and process-specific reasons. As this article is written, the machine has been in operation for about 8,000 hours without major problems.

Jan 1, 1998

By R. Fraher

The control of mine roof is of vital interest in underground coal mining not only for reasons of safety, but also to avoid the high costs of cleanup, resupport and production losses that can result from roof falls. The difficulty in determining roof stability mine-wide is due in large part to the broad variation of geologic and structural conditions that typically exist throughout a mining area. To ensure a stable roof over the entire mine, support systems must be selected to minimize the possibility of failure. The magnitude and cost of the support selected is a trade off against the cost of the number of falls that can still occur after it is installed. Because of the large number of variables involved in analyzing and optimizing roof stability versus support, a digital computer simulation was selected to find a cost effective solution to roof support design. A total cost approach is used which includes the actual cost of the roof support as well as the cost of the roof fall in terms of resupport and loss of production (Fraher 1990a). A Monte Carlo simulation program called ROCSIM (Roof control Optimization Cost SIMulation) has been developed for determining the optimum roof control system and design layout for underground room-and-pillar mining.

Jan 1, 1992

By G. B. Misra

Heat transfer in partially wet mine airways has been the subject of study for quite some time. Of the available models some are quite empirical while some involve highly complicated computation. Models developed by Amano, Mizuta and Hiramatsu and Banerjee and Chernyak as well as that modified by Misra were evaluated for prediction of the rise in temperature and humidity (mixing ratio ) of partially wet mine airways at four different levels in the Mosaboni Mine of Hindustan Copper Ltd. Measurements of barometric pressure, virgin-rock temperature and changes in dry- and wet-bulb temperatures along a certain length of airway were made. The rise in dry-bulb temperature and mixing ratio of air over the sections were calculated using the three models. The study reveals that calculated values of temperature and moisture content agree within possible rage of experimental error with all the three models in case of three levels with low wetness factor, but the agreement was poor for the relatively more wet airway on the 30th level. Errors in the estimation of fw to the tune of 0.025 can lead to fair error up to 0.94 K in the estimated temperature while alternative ways of estimating the heat transfer coefficient [] can introduce errors up to 1.45 K.

Jan 1, 1987

By J. A. Brierley, C. L. Brierley, R. C. II Blake, S. McGinness

A principal long-term goal of this laboratory is to achieve a detailed understanding at the molecular level of the microbial-dependent solubilization of minerals. Three recent advances in this research are summarized. (i) An in situ electrolytic procedure is described whereby large quantities of autotrophic iron-oxidizing organisms may be achieved for fundamental or applied studies. Over 600 grams wet weight of Thiobacillus ferrooxidans were harvested from a single 55-gallon growth vessel. (ii) A basis is presented for classifying some 70 different iron-oxidizing bacteria into one of 4 categories, depending on the type of redox-active electron transport proteins expressed during aerobic respiration on reduced iron. Comparative spectroscopic analyses indicated that different electron transport mechanisms exist in different genera and species of acidophilic bacteria that respire on iron. (iii) A method is introduced to investigate the binding interaction between bacteria and minerals, based on changes in the electrokinetic properties of the two species. Preliminary experiments indicated that the electrophoretic mobilities of pyrite and Thiobacillus ferrooxidans were both altered when the two colloid particles were mixed prior to the actual electrokinetic measurement. The need for more basic information regarding all aspects of the microbial-dependent solubilization of minerals is evident.

Jan 1, 1993

By M. R. Stokes

Over the recent years there has been an increase in the application of retreat mining on longwall faces as mine operators strive for ever greater productivity. The purpose of this paper in then to review current practice as a starting point and then move forward to discuss the future geometry's that a longwall face may take. Single and double production zone three roadway faces are assessed. All possible configurations of three roadway faces are defined. Unsuitable configurations are rejected after analysis of broad ventilation issues. The remaining configurations are then assessed on an operational basis, this includes: limits on retreat synchronisation, structure of centre gate, floor bulging and equipment installation. The remaining viable configurations are then further assessed on ventilation issues, this includes: provision for gas control/gas fringe, face climate and balancing of face flows. Possible face climate is assessed using numerical simulation of the various configurations, the predicted dry/wet bulb temperature and predicted levels of heat stress indices are given and discussed in detail, along with face flow balancing. The necessary conditions required for the successful operation of a double production zone three roadway face system are formulated, together with conclusions as to the possible level of application.

Jan 1, 1997

By Victor Rudenno

Cut-off grade is one of the most critical parameters affecting project cash flow. Its sensitivity is due to the number of other parameters that are correlated with any change in its value. Changes in cut-off grade, average grade and ore tonnage vary and they in turn can affect such parameters as capital and replacement costs, recovery, life of the project and operating costs. Perhaps one of the best definitions of cut-off grade is that of Taylor (1), "... any grade that, for any specific reason, is used to separate two courses of action, e.g. to mine or to leave, to mill or to dump ... . Obviously the most likely specific reason is one governed by economics, involving the return of investment and sufficient profit to motivate development and mining of the deposit. In this paper the cut-off grade is defined as that mining limit which will maximise the economic return for a projected mining venture. The following brief literature survey indicates that when computing the optimum cut-off grade there is a need to be able to directly compute the Discounted Cash Flow Rate of Return (DCFRR) or Net Present Value (NPV), as economically as possible, while allowing for parameter dependencies and variation in project structure.

Jan 1, 1979

By S. P. Banerjee

Injection of inert gases to combat mine fires has been practiced in various parts of the world for a long time. Of late, nitrogen has become the preferred inert gas for control of mine fires and safe salvage of longwall equipment as compared to carbon dioxide or fuel gases produced from burning of fuel. In India, carbon dioxide has been used for fire fighting in a number of mines during the 1960s and 1970s. More recently inert gas produced from burning of fuel oil in surface plants has been used in controlling the atmosphere in fire areas in two mines. In yet other cases, liquid nitrogen has either been poured directly into fire areas in liquid form or injected in gaseous form to keep the fire in check. Nitrogen produced in liquid form in an oxygen plant is more costly than nitrogen produced from PSA (pressure swing adsorption) based plants. A PSA-based plant has been installed in one of the Indian mines in 1986 and more are in the offing. This paper reviews the application of various inert gases in Indian mines and discusses the likely trend of inert gas application in Indian mines in the future.

Jan 1, 1987

By John P. Dunford, Lewis A. Martin

Researchers from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, in cooperation with engineers from the Department of Mining and Geological Engineering, Montana Tech, Butte, MT, conducted tests to evaluate the tensile strength, fiber count, and adhesion of shotcrete applied to panels at the Chief Joseph Mine, a research and training facility operated by Montana Tech. The tests were conducted in the mine ramp 45 m (150 ft) inward from the access portal at a 15.25-m- (50-ft) long test area divided into five 3-m- (10-ft) long sections. The shotcrete was applied with an Aliva 240.5 machine fitted with a predampener. Different amounts of fiber were entrained for each panel. Background data for the tests were obtained from earlier tests in Nevada, where the typical amount of fiber in the shotcrete is 6.54 kg/m3 (11 lb/yd3). All shotcrete was applied to a minimum thickness of 76 mm (3 in). Cylindrical cores were drilled at the wall-rock interface, and adhesion was tested after 28 days of curing. The goal of this research is to reduce the need to install multiple supports at the advancing face by creating a safer mining system that limits the time miners are exposed to unprotected roof.

Jan 1, 2005

By R. D. Schmidt, S. E. Follin

Introduction Mineral recovery from an in situ leaching operation is determined by the often complex interaction of hydrology, mass transport, and chemical kinetics. The operating conditions of many pilot and production scale uranium leaching operations involve heterogeneities in aquifer permeability. Differences in permeability may be naturally occurring, the result of differences in main size or cementation, or they may be induced by leaching activity. Variations in permeability directly affect the fluid flow streamline pattern, fluid flux, and so also leaching geochemistry and uranium recovery. An in situ leaching hydrology model (ISL) and a mass transport-oxidation rate model (ISLGC) have been developed for use in making site specific predictions of the leachability and productive potential of heterogeneous ore deposits, and for the optimal design of leachant injection and recovery operations. The two models are linked by output and input requirements. The ISL hydrology model generates a leachant flow streamline pattern between injection and recovery points in a flow domain incorporating regions of arbitrary permeability. The ISLGC transport model describes the changing solution concentrations of uranium and oxygen and the changing mineral concentrations of uranium and pyrite resulting from convection, longitudinal dispersion, and oxidation reactions. ISL hydrology model Basic equations The differential equation for steady-state two- dimensional flow in an isotropic porous medium is

Jan 1, 1988

By Richard A. Williams

The design, modelling and simulation of solid-liquid mixers remains one of the least advanced aspects of minerals processing, due to difficulties in quantifying complex slurry hydrodynamics from first principles, and in acquiring reliable experimental data for model verification and development. This contribution describes the application of electrical resistance tomography (ERT) for three dimensional imaging of the concentration of mineral particulates in a slurry mixer as a function of key process variables (particle size, impeller type, agitation speed). It is demonstrated how ERT can provide a wealth of detailed data to allow model development, which ultimately will lead to much improved design capabilities and the generation of mixing models which could reside within Particle Process Simulators. This principle is illustrated using descriptions of mixer behaviour based on an empirical approach, although the measurement methodology described is equally suited to development of computational fluid dynamics models, cellular models or design approaches based on artificial intelligence. The experimental data can be built into a visualisation data bank, which acts as a "process toolkit" by allowing a library of process responses to be catalogued. Hence these data can be accessed for the purposes of model development, equipment selection, optimisation of operating conditions or testing on-line control strategies.

Jan 1, 1995

By J. A. Herbst, J. E. Bohrer, Y. C. Lo

A systematic approach has been developed to analyze a phosphate grinding circuit with a view toward determining promising alternatives for increasing mill capacity. This analysis was carried out and capacity increases were predicted in the context of detailed population balance models developed for the plant ball mills and classifier systems. Model development and verification was performed using data obtained in a series of batch tests and two plant test campaigns. The effects of feed rate, percent solids, ball size, and mill material filling, etc., on grinding were investigated in the laboratory and plant. Residence time distribution tests were also performed to determine the transport behavior in the mill. The population balance models were found to provide accurate predictions of full-scale grinding circuit performance. Based on the findings of this study, additional capacity in excess of 25% was predicted for these ball milling circuits by a proper combination of ball size change, mill dilution, and adopting screen classification in place of hydro-cyclones. These predictions have been confirmed by plant tests in which the recommended operating changes have been implemented. Understanding the effects of operating variables on breakage kinetics and the interplay between kinetics, transport, and classification has contributed significantly to increasing the mill capacity.

Jan 1, 1988

By F. C. Schwerer, C. R. McKee, J. C. Seccombe

Production of methane from coal seams requires hydrofracturing, and the length of a hydraulic fracture determines we11 spacing. Since the volume of fluid injected is known, the fracture length is the volume divided by average width and height. If the fracture is contained in the known height of the seam, then fracture width becomes the major factor con- trolling length. Width is proportional to coal compressibility; bulk compressibility is known to be larger than intrinsic compressibility. A method is given here to measure in-situ compressibility (a) from transient pressure testing. Theory linking flow in porous media with rock mechanical properties is reviewed. A consistent derivation of the porous flow equation is given incorporating 3-D deformation and the effective stress parameter "st' linking changes in effective stress and pore pressure. The relations for "st' in terms of a and intrinsic compressibility (ai) are substituted into the field measured porosity-compressibility product (net) and solved for a, the constrained matrix compressibility. In a field example, using 4 wells with an anisotropic analysis, the ratio of major to minor permeability was 17 for the Pratt A seam. a was found to be 6x10-5/psi as opposed to the laboratory value of 1.4x10-6/psi.

Jan 1, 1986

By H. Burger

For mine planning in the hardcoal industry the reliable prediciton of the properties of a deposit-both ahead of the zone to be worked as well as of zones at depths not yet developed - may help improve the production results of workings. With the wide spacing of exploration drillings usual in the coal industry, it is hardly possible to establish adequately reliable plans just by simple kriging methods. During the exploration phase a decision has to be made whether the zone ahead of a face area is economically profitable and, in addition, accessible and safe in order to be included in the production planning. It is, first of all, important to gather global information on certain parts of the planning area it the form of local estimates. Moreover, cut-off problems play a critical role, e.g. if there are set cut-off thicknesses as a criterion for minability or if safety aspects have to be considered. Conditional simulation appears to be a useful geostatistic method in order to localize or predict areas of potential rock burst hazard - based on geological criteria in conjunction with the guidelines by mining authorities - in the zones ahead of a working. It is a means of providing an objective basis for the evaluation and planning of mining activities.

Jan 1, 1986

By P. R. A. Andrews

Areas of bubble contact were delineated for topaz and tourmaline in the presence of chloride, fluoride, sulfate, phosphate, oxalate, and citrate ions using dodecylamine hydrochloride collector. The limits of pH and the minimum collector concentration were established using the bubble pick-up technique. Bubble contact did not occur below the p.z.c. (point of zero charge), estimated to be 5.6 for topaz and 6.6 for tourmaline, in the presence of chloride ion. Flotation below the p.z.c. was, however, extended by citrate, oxalate, phosphate, sulfate, and fluoride ions. Oxalate, citrate, and fluoride ions displayed the greatest pH range of activation, followed by phosphate and sulfate ions. Chloride ion acted as an indifferent electrolyte. Topaz was selectively activated with respect to tourmaline by fluoride and phosphate ions. Topaz was activated by fluoride ion between pH 2.4 and 5.6. Tourmaline flotation in this pH range was virtually insignificant. Topaz was activated by phosphate ion between pH 4.9 and 7.4. Tourmaline flotation in this pH range was only partial. Activation appeared to be strongest when anionic protonated species were in maximum concentration. Strong activation also corresponded to very stable metal ion species thought to be formed on the surface of each mineral.

Jan 1, 1991