Search Documents

By H. S. Chang

A three-dimension two-phase (air and dust) computer model was developed to model air velocity and respirable dust distributions in the longwall faces. This paper describes the derivation of the model including the model features, mathematical equations and boundary conditions. Example simulations were also performed for two longwall faces where measured respirable dust and air velocity distributions were available. The results indicated the model can simulate the mine conditions fairly accurately.

Jan 1, 1996

By W. M. Shaver, R. Letourneau, W. R. Dengler

Dynatec Mining Limited contracted to sink a 1500 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.5 ft) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (15 ft.) diameter double-drum hoist to sink the shaft with 12.5 tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1991

By Jozef S. Stachulak, Bruce R. Conard

INTRODUCTION The concern of occupational exposure to diesel exhaust pollutants is an important workplace issue for the mining industry. During the last three decades of diesel operations at Inco, a significant amount of research and improvement has been made in the area of work environment, and effective diesel operation. This paper will review the experience gained by Inco's Ontario Division from the implementation and the use of modern engines, improved fuel quality, and the exhaust control technology, coupled with adherence to proper maintenance and ventilation design and practices. Past monitoring practices and the current occupational monitoring program at lnco are outlined. A major new research initiative involving multi-stake holders in diesel performance is described. MINING IN THE SUDBURY AREA The discovery of nickel-copper ore in the Sudbury area dates back to the year 1856. The existence of this orebody was noticed when a strong compass deflection was observed by a provincial surveyor. This discovery, even though documented in official re- ports, failed to arouse any public attention at that time. In 1884, a rock-cut was blasted through a small hill near the village of Sudbury to permit laying track for the Canadian Pacific Railway (Boldt 1967). The rock-cut uncovered a body of massive sulfides with a copper content of over nine percent. The mineralization is concentrated along the outer margin of the Sudbury Basin, an oval-shaped structure having a dimension of 55 x 95 kilometres. The ore extends down-dip to to at least 3000 metres below the surface. The mining methods at lnco can be divided into two categories: "filled-stope" and 'bulk" mining. This division, in the broad sense, may also reflect the environmental conditions of the mine. In the past, the selection of a mining method was based on the size, shape, grade and the strength of the ore and its surroundings. The recent development of improved technology and mining equipment permitted wider application of low cost bulk mining methods. UNDERGROUND DIESEL EQUIPMENT The first diesel-powered machine, a 145-horsepower scooptram, was put into operation in March 1966, in a cut-and-fill stoping complex at Frood Mine. The number of diesel machines underground in the Inco, Ontario Division, mines was increased to 360 units by 1971,550 in 1977 (Rutherford 1978), and over 830 diesel-powered units in 1995. The following list indicates current mobile diesel equipment. LHD 194 Loaders 81 Trucks 28 Jumbo Drills 78 Personnel Carrier 101 Service Equipment 155 Locomotives 50 Bolters 30 Scissor Lift 113 About 20 percent of the LHD and truck units are equipped with electronic fuel controlled engines. COMPOSITION OF DIESEL EXHAUST Diesel exhaust contains hundreds of pollutants (Watts 19921, including components of unburned fuel and lubricating oil and products of incomplete combustion of the fuel and oil. These pollutants are emitted either as gases or as particles. Gaseous pollutants include carbon monoxide, nitrogen oxides, and sulfur ox- ides, as well as a variety of organic compounds, such as hydro- carbons, aldehydes, and polynuclear aromatic hydrocarbons. The particle phase, also known as diesel particulate matter (DPM), is the filterable portion of diesel exhaust. Figure 1 depicts the trimodal particle size distribution that arises from different mechanisms of aerosol generation (Cantrell and Rubow 1992). Primary combustion aerosols, including diesel exhaust aerosol, are formed as very small particles (in the 0.001 to 0.08 micrometre range), but physical mechanisms such as condensation and coagulation quickly transfer the aerosol mass from the nuclei mode to the accumulation mode. These processes result in a mass median diameter of approximately 0.2 micrometres for diesel particulate matter, and 90% of the particles are less than 1.0 micrometre in size. These particles have a high surface area, permitting the adsorption of different substances produced during combustion. Mechanically generated aerosols, on the other hand, typically contain particles greater than 1 micrometre in diameter. The particle phases of diesel exhaust contain three components (Bagley, et al, 1996) shown by Figure 2, namely: a carbon- aceous fraction composed mainly of solid-carbon particles, a sulfate fraction containing small hydrated sulfate particles, and a soluble fraction that contains compounds that are soluble in organic solvents and are adsorbed or condensed onto carbon core particles. These compounds consist primarily of higher molecular weight hydrocarbons and PAH's and may contribute 15% to 45% of the weight of the total particulate matter (Schuetzle, 1983). The control of these pollutants is necessary to ensure a healthy work environment. Proper engine maintenance, engine design modifications, improved fuel quality, and use of exhaust control technology, coupled with good ventilation practices, all

Jan 1, 1997

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes thermal drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of commercial dewatering devices were developed for the Coal Cleaning Simulator running under Aspen Plus? during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for size degradation in the devices and fines loss to effluents, where appropriate, and a calculation for moisture content of the product based on particle size and specific gravity distribution. This paper discusses the algorithm for coarse and fine coal centrifuges and gives comparisons between predicted moisture and solids loss and published moisture and solids loss values for various particle size ranges.

Jan 1, 1996

By Donald S. Clarke

The Umuna epithermal precious metal deposit has provided the target for a simulated rock geochemistry exploration program, directed at bedrock exposed in the drainage system of eastern Misima Island. A geochemical halo to the deposit is readily recognised in the mafic meta-volcanic country rock. This halo is defined by anomalous results for both major (K, Na, Ca, Mg) and minor (Au, As, Sb, Cu, Pb, Zn, Ba, Rb, Sr, Cs, Bi, Ga, S) element geochemistry, extending further than 1km from the deposit. Such halos are sufficiently extensive to provide adequate exploration targets in the search for epithermal mineralisation, complementing mineralogic and secondary media geochemical investigations.

Jan 1, 1989

By Kim McKnight

Dupont has successfully incorporated a Floatex Density Separator into its wet-gravity operations for the recovery of zircon from titanium tailings. Results indicate that the Floatex achieved a zircon recovery of approximately 95% while rejecting similar amounts of quartz and other gangue minerals. Additionally, a unit capacity approaching 16 tonnes/hr/m2 was achieved. Results also show that the alumino-silicates can be separated into other product streams that will further improve process economics and minimize waste material. The improved plant feed grade provided by the Floatex has allowed for either an increase in overall plant capacity and/or final product grade. This paper will present the findings from the in-plant study.

Jan 1, 1996

By M. C. Williams, T. P. Meloy

For over thirty years the Population Balance Model, PBM, has been the mainstream modeling method for comminution unit operations and comminution circuits. For commercial comminution circuits the method is based on erroneous physics and dubious numerical mathematical methods leading to non unique solutions that have little extrapolative value and faulty control strategies. In short the PBM is wrong. Given is a detailed analysis showing a number of non trivial flaws in the linear PBM. Moreover, a simpler model is presented that leads to a solution of the comminution circuit predicting the size distribution output over a variety of conditions. Because the linear PBM is firmly entrenched, an award is offered, $10,000, to any researcher that can use the linear PBM and its present numerical methods to predict the typical straight line, self similar, output of wet mills over a variety of grinding times.

Jan 1, 1992

By R. Jerez

This paper describes practical applications of lineal" programming techniques to help in the planning of production, transportation and shipments at different coal mines. The models are being used by Cyprus Coal Company in eastern and western operations to plan coal production, economic dispatching and blending over variable time horizons. In addition, where a preparation plant exists, the models establish the amount of washing required to meet specific coal sales qualities. The emphasis on this paper is on model development and implementation together with a system to track coal flow and qualities, either raw from the mines to the loading facilities 01" processed through a preparation plant.

Jan 1, 1991

By M. Ge, C. Mborah

"The acoustic emission/microseismic monitoring (AE/MS) technique has widely been used in the mining environment for the monitoring of rock mass stability. A successful implementation of the method is hinged on being able to accurately determine the P- or S-wave arrival which is then used in the determination of the source of an event. Determination of the arrival phase is usually performed visually by a human expert. However, the mining environment is characterized by high noise levels and different noise types of varying intensities. Therefore, performing manual phase picking on time series data acquired from the AE/MS monitoring system can sometimes be tedious and time consuming if not impossible. In this paper, a proposal for improving manual P-wave phase arrival picks is discussed. The method involves the filtering of the AE/MS data using a stationary discrete wavelet transform (SDWT) method. After filtering, appropriate scales/levels of the multi-level decomposition process are then selected for further processing. The first step in the picking process after filtering, requires the computation of the signal power and the root mean square (RMS) using the signal amplitudes at each scale. The preliminary P-phase arrival time is picked using the results of the calculated power and RMS values respectively. The calculated RMS values are then superimposed on the calculated power values to determine the final arrival picks. If the arrival time picks obtained by both methods coincide or are within 5 to 10 sample points, the pick is considered reliable. The accuracy of the method was verified using AE/MS data from two datasets obtained from two separate underground mines. The results of the study showed that the picking method is reliable and robust. Based on the data studied, it can be concluded that the method will help reduce the time usually spent in processing AE/MS data from mines. INTRODUCTION A successful identification and location of the source of acoustic emission/microseismic (AE/MS) events is mainly dependent on the onset time of the P-wave phase. In many seismic networks, initial picks are performed by picking algorithms followed by manual picks by human experts. If the waveform signal-to-noise ratio (SNR) is low, the P-wave onset time picks by the human expert is generally reliable and accurate [1]. However, for waveforms with high SNR, picking of the P-wave onset could be a major challenge. Also, due to the volume of data acquired daily, manual processing could be stressful and time consuming [2]. These challenges continue to provide motivation for alternative means of providing reliable and efficient ways of improving manual phase picking. The AE/MS technique has been an intergral part of safety monitoring in mines [3] due to its capacity to identify zones of instability in a monitoring area. To obtain an accurate source of an AE/MS event however depends on the quality of the data used for P-wave phase picking [4, 5]. AE/MS data from mines are generally contaminated with excessive background noise generated by the different mining operations. The AE/MS signals of interest are mostly buried in background noise which makes it difficult to pick the P-wave phase arrivals [4]. Processing AE/MS data acquired in noisy environment remains a major challenge due to the weak nature of AE/MS signals [6]. As noted by [4] most of the data recorded in the mine environment are mainly due to events not related to AE/MS events of interest. The complexity of data in this type of environment makes the detection and picking of P-wave arrival by human experts a very difficult task."

Jan 1, 2017

By Jiachen Wang, Nan Wang, Yang Li

The close-multiple coal seam is an important component of China’s coal resources and plays a key role in total coal reserves. However, the overburden movement in the mining process of close-multiple coal seams is usually extensive, which is seriously affected by overmining. It is therefore essential to study the mechanism of roof breakage, the relationship between the shield and the surrounding rock, and the mechanism of overburden movement to ensure the safe operation and the efficient exploitation of close-multiple coal seams. This work first proposes a technical route for intelligent ground control. Second, the principle of cooperative control between the shield and overburden roof is revealed, and the shield support capacity calculation method is summarized. Third, the quantitative criterion for disturbance degree of key stratum (KSDD) is proposed based on the key strata theory. Finally, several intelligent evaluation and analysis systems have been developed in terms of overburden breakage and shield support capacity, multi-information analysis of ground control, and disturbance degree of overburden. The research results may provide an essential reference for the development of intelligent ground control in the mining process of close-multiple coal seams

Jul 1, 2023

By Ren Bryce

The ninth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the SME Annual Conference & Expo in Minneapolis, MN. A total of 33 students presented their work at the contest. The competition began in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes. The students worked hard at their research and then set aside time to complete all the necessary steps to enter the contest. The MPD recognizes the effort required to enter and, as a result, provides monetary rewards to all participants. As in past years, there are separate levels of competition for undergraduates and graduates, and the prizes are designated accordingly. At the graduate level, first place receives $1,000, second place $500, third through seventh $200 each, and all others $125 each. At the undergraduate level, first place receives $1,000, second place $500, third place $250, and all others $125 each.

By W. M. Shaver, R. Letourneau, W. R. Dengler

Dynatec Mining Ltd. contracted to sink a 1500-m (4920 ft) concrete-lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft has an inside diameter of 6.3 m (20.5 ft) and is equipped with steel furnishings. Dynatec used the owner-supplied, 4.6-m (15.1 ft) diam, double-drum hoist to sink the shaft. For muck removal, 12.5¬t (13.8-st) buckets were used. The capacity of the concrete-¬placement buckets was 4.6 m3 (162.4 ft3). One of the unique features of the shaft sinking operation was the use of a two-¬boom, electric-hydraulic drill jumbo permanently mounted in the shaft sinking stage. An in-the-hole (ITH) drill was used to drill a 200-mm (8-in.) cut hole for the 4.8-m (16 ft), full face rounds. This paper describes the performance obtained with the electric-hydraulic drilling equipment and the high-capacity muck removal and concreting equipment.

Jan 1, 1994

By A. E. Ketler

Optical smoke monitoring fills an important gap in ventilation and fire safety: namely monitoring of smoky, low temperature fires where little CO and heat are generated. Smoke monitoring also avoids the nuisance alarms due to diesel exhaust, battery chargers, blasting and welding. The smoke optical density (OD) fire alarm standard specified by MSHA presents an opportunity for improved safety. Experience of actual mine usage of the SmokeBoss*100 is reviewed, with particular regard to effectivity, maintenance and cost.

Jan 1, 1995

By Paul E. Scheerer

Synthetically produced magnesium hydroxide serves as the precursor for much of the magnesium oxide produced in the world today. Magnesium oxide, in a variety of physical and chemically reactive forms, is a very important commodity. It is used as the main component in refractories employed in steelmaking furnaces and in many base metal refining furnaces. In the chemical industry, it serves as a raw material in the production of epsom salts, rayon acetate, oxychloride and oxysulfate cements and magnesium sulfonates. It is a minor component in fertilizers and animal feeds. It serves as the starting material for producing fused magnesia, used as an electrical insulator in electric heating elements. It is employed in the magnesium sulfite process for pulp digestion in the paper industry. Additional uses are in SO2 scrubbers, as a neutralizing agent in the tanning industry and as a component in rubber compounding. Magnesium oxide is produced not only from synthetically produced magnesium hydroxide. It is produced from natural magnesites, natural brucites, and natural and synthetic hydro-magnesites. Synthetic magnesium hydroxide, as a starting material provides more control of the chemical purity and chemical reactivity of resulting magnesium oxide products because of the uniform nature, chemical and physical, of the hydroxide that can be produced. Synthetic magnesium hydroxide is produced by precipitation of Mg (OH)2 from magnesium chloride bearing seawater or natural brines through the use of a base such as Ca(OH)2 or NaOH.

Jan 1, 1978

By J. S. Martin

The redesign and reinforcement of a highwall located adjacent to a $10,000,000 shopping center, destabilized by active subsidence, was conducted after an extensive geotechnical investigation. The highwall was excavated in a hillside where a coal seam had been retreat mined and augered. Engineering geological mapping, determination of the properties and behavior of the intact rock, fractured rock, and urethane grout material, and soil were required to characterize the highwall and conduct a stability analysis. Remedial measures included re-excavating portions of the highwall to reduce the slope angle, and pressure grouting of the immediate roof.

Jan 1, 1988

By G. D. Naugle

Deep open-pit mines invariably affect the local and regional hydrologic systems. Pit dewatering, occurring during mining operations, puts an obvious hydrologic stress on these hydrologic systems. However, post-mining hydro-logic impacts resulting from the pit refilling with ground water following the cessation of mining activity can also be significant. Prediction of the rate at which the post-mining pit will fill with ground water is a critical aspect of assessing such long-term hydrologic impacts. Numerical ground-water flow modeling prov1des a method that can be used to predict the rate at which pits will fill with ground water.

Jan 1, 1992

By A. Hekmatnejad

"The objective of this work is to validate a methodology for spatially predicting the fracture intensity, defined as the average fracture area per unit volume. First, using the observations from drill holes, the fracture intensity is directly inferred at the support of drill-hole composites based on a Terzaghi correction. Subsequently, the composite values are interpolated to larger blocks. The methodology is tested on sets of simulated fracture networks, in which each fracture consists of a disc with a random diameter, random position and random orientation. For each of these simulated networks, one can calculate the actual fracture intensity within any region of space, based on geometric considerations. A regular sampling mesh is then defined to emulate a set of vertical drill holes and the proposed methodology is applied to predict the fracture intensity, both globally and locally. The actual and predicted fracture intensities are finally compared, showing that predictions are unbiased, insofar as, on average, the prediction error is always close to zero. Also, the error dispersion increases when the support of the prediction decreases, which is consistent with the well-known support effect. In practice, the proposed methodology allows predicting fracture intensity based exclusively on drill-hole information, without the need for simulating fracture networks in space, hence its interest. INTRODUCTION The characterization of fractures in rock masses is an important part in the evaluation of mechanical and hydraulic properties of rocks. Fractures have a large impact in disciplines such as reservoir engineering, safety of underground storage of CO2 or of nuclear waste, assessment of high-enthalpy geothermal installations, safety of mining exploitations, efficiency of in-situ leaching operations or of extraction by block-caving. As a rock mass property, fractures must be characterized in the three-dimensional space, whereas observations are limited to 1D (drill holes) and 2D (outcrops, drift walls), moreover very often to rather short stations, so that the available data are subject to geometric bias, truncation and censoring. Fracture characteristics includes the number of fracture sets and, for each set, the number, orientation, spacing, location, shape and size of the fractures must be inferred from data sampling. Some important parameters that are considered nearly in all models are fracture intensity and fracture size."

Jan 1, 2016

The heat of immersion of coals in different immersional liquids is measured as a function of particle size and moisture content. Decrease in particle size shows a concomitant increase in the heat of immersion. The heat of immersion is dependent upon the nature of immersional fluids. In addition the nature of moisture present in coal influences the heat of immersion.

Jan 1, 1993

By Jack Barrett

The oxidants which participate in the bacterially catalyzed oxidation of minerals are dissolved oxygen and some aqueous iron(III) complexes. Speciation studies indicate that these complexes consist of iron (III) -sulfate and iron (III) -arsenate ions. The complexes have different oxidizing powers as indicated by their calculated standard reduction potentials. The thermodynamics of the oxidations of pyrite and arsenopyrite are related to the mechanisms of the reactions. The mechanisms are discussed in terms of primary processes occurring on the mineral surfaces and the secondary reactions of the primary products. The importance of the conclusions to plant operation is discussed.

Jan 1, 1993

By L. Bloom

"Man-Made Parameters" refers to the importance of selecting appropriate analytical procedures to acquire useful chemical data. The correct procedures are particularly critical at the sample preparation stage where decisions concerning pulverizing equipment, sample size, contamination and dissolution will impact on the final results independent of the instrumental method of analysis. Several experiments were designed to quantify the impact of these approaches.

Jan 1, 1993