Search Documents

By T. Könighofer

Processing of copper-cobalt orebodies in Africa?s Copper Belt has received much recent attention with various flowsheet options being developed specifically for the refining of cobalt. The upfront leach and copper refining routes are well understood whereas the refining of cobalt is more complex, requiring numerous impurity removal steps to produce high purity metal. This paper describes an investigation into one of the possible processing steps in the refining of cobalt, namely, cobalt solvent extraction. The paper emphasizes the importance of upstream impurity removal to achieve the required cobalt solvent extraction feed composition. 18% (v/v) Cyanex 272 in an aliphatic diluent is used as the organic phase. The pH profiles in the various stages are evaluated in order to obtain a raffinate containing <10 mg/[l] cobalt and with a low magnesium content reporting to the stripping section. The pH profile is also used to minimize the impurity deportment to the cobalt electrolyte. The effect of adding a preneutralization stage before feeding the organic phase to the extraction circuit is investigated. Zinc build-up in the stripping stages is also looked at. It is recommended for the purpose of this study that four extraction stages at an O:A ratio of 1 with a pH profile from 4.9 to 5.7 be employed. The pH is controlled with 40 g/[l] NaOH. A preneutralization stage is required, where the organic phase is contacted with 10 M NaOH. Two scrubbing stages are recommended at an O:A ratio of 40, using the cobalt electrowinning advance electrolyte as the scrub liquor. Three strip stages are to be employed at an O:A ratio of 0.67.

Jan 1, 2009

By Neal Harries

The monitoring of rock slopes is a common procedure in the management of hazards associated with slope instability. Slope stability radar has become widely accepted as the state-of-the-art method for management of hazards associated with unstable slopes in open pit mines. This is confirmed by the rapid adoption of the technology since inception in mid 2003, with over 70 GroundProbe slope stability radars now in use at open pit operations throughout the World. The use of a monitoring system such as slope radar to identify slope hazards is only part of the solution to minimise the consequences associated with slope instability. The presence of the hazard must also be effectively communicated to the mine personnel, so that the correct response to the hazard can be enacted, and the risk mitigated to an acceptable level. In some surface mines, due to the geotechnical characteristics of the rock mass, hazards can develop rapidly; with slopes progressing from stability to ultimate collapse in just hours. In these situations, it is vital that efficient systems are developed to evacuate the area of the pit affected. Such a system has been developed by GroundProbe in South Africa, with the vital driving force for the project being provided by the Anglo Platinum Mogalakwena mine operation based at Mokopane. The mine based development of the system was perceived as an essential aspect in the development of the successful system. From an early stage, the mine provided essential input on both hardware and software developments to allow the system to be rapidly integrated into the mining operation. This paper describes the pit evacuation alarm system that was developed and discussed the benefits obtained from a mine based development program.

Jan 1, 2008

By T. Feroze, B. Genc

"The ventilation of underground coal mines plays an important role in minimizing the risk of methane and coal dust explosions. The ability of ventilation, with the use of line brattices (LBs), to remove methane and coal dust in empty headings is dependent on the amount of air leaving the LB and entering the heading. The quantity of this air depends on the associated system variables, namely heading dimensions, settings of the LB, and velocity of air in the last through road (LTR). However, the exact effect of these system variables on the flow rate at the exit of the LB in an empty heading is not known. The installation of LBs in South African coal mines is generally carried out based on experience. This can result in overor under-ventilation and may increase the cost of providing ventilation or cause accidents, respectively. In this paper, using computational fluid dynamics (CFD), the air flow rate at the exit of the LB in an empty heading was estimated using full-scale three-dimensional models. The CFD model used was validated using experimental results Firstly, the settings of these three system variables were varied, the flow rates at the exit of the LB were measured, and finally the results were used to calculate the effect of each system variable. The outcome is a mathematical formula that can be used to estimate air flow rate at the exit of the LB in empty headings for any practical scenario.This paper will help the coal mining sector in South Africa by providing estimation models based on scientific reasoning for the installation of LBs, and will also serve academia as part of the curriculum towards educating future mining engineers."

Jan 1, 2016

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installationof LBs remains a challenge. In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installation of LBs remains a challenge.In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By A. Becker, R. Tait, S. L. George, A. Carlisle

Surface treatments like laser shock peening (LSP) induce residual stresses penetrating up to 1 mm deep, surpassing traditional methods, thus significantly increasing the potential impact on materials prevalent in the automotive and aerospace sectors. Through extensive fatigue testing and fractography investigations, it was determined that LSP resulted in a fatigue life increase of over five times for aluminium alloy AA7075-T6 and titanium Ti-6Al-4V. Increased fatigue life was also noted in AISI316 stainless steel, which showed increases in fatigue life of 1.7x. While fatigue life in all cases improved, the efficacy of LSP was shown to be material dependent.

Jul 23, 2025

By B. K. Loveday

A Colloquium on &apos;Control and Simulation in the Minerals Industry&apos; was held at the Holiday Inn, Milner Park, on 20th September, 1984, in conjunction with the Electra Mining Exhibition. A total of 170 persons attended the very full morning programme, which began with an opening address by the President, The South African Institute of Mining and Metallurgy, Mr l.D. Austin. He outlined the reasons why computers were being used to an ever-increasing extent for control and simulation in the minerals industry. The computer was even used to check, among other things, the validity of the signals it was receiving by mass-balance calculations.

Jan 1, 1985

By N. B. Strydom, P. L. Jooste, H. F. Kotze, W. H. Van Der Walt

Note: A revised method of heat acclimatization by N. B. STRYDOM, W. H. VAN DER WALT, P. L. JOOSTE, and H. F. KOTZE INTRODUCTION Climatic-room acclimatization was introduced in the gold-mining industry in 1965 and was rapidly adopted by all mines because it reduced the number of days required for heat acclimatization from 12 to 8. The method has been adequately described in previous papers1, 2 but, briefly, requires four hours of heat exposure per day while the work rate is progessively increased from 35 W on Day 1 to 70 W on Days 7 and 8. Several attempts to shorten

Jan 6, 1976

Infacon 74 Members are reminded of the International Ferro-Alloys Congress that is to take place in Johannesburg between 22nd April and 1st May, 1974. The Congress is being held jointly by the National Institute for Metallurgy, the Ferro Alloy Producers&apos; Association of South Africa, and the South African Institute of Mining and Metallurgy. Correspondence and enquiries should be addressed to The Secretary, Organizing Committee, INFACON 74, Private Bag 7, Auckland Park 2006. The gold deposits of the farms Lisbon and Berlyn in the Eastern Transvaal by v. c. H. R. BRERETON. Published in the Journal November 1973. AUTHOR&apos;S CORRECTIONS The following amendments should be made.

Jan 2, 1974

By M. U. Ozbay

This paper presents an overview of the research that has been carried out to improve the understanding of the fracture processes occurring in rock under high levels of stress. The onset and growth of fractures are studied by means of laboratory model testing, and the results obtained are used in the calibration and validation of the numerical model DIGS, which is based on displacement discontinuity. The results obtained so far have shown that, while there are overall similarities between the experimental results and the numerical simulations, improvements to the experimental procedures and the DIGS are required for a detailed mechanistic understanding of shear-band orientations and extension fractures.

Jan 1, 1996

By C. T. Connor, O&apos

The fifth University of Cape Town (UC1)/University of Stelenbosch (US) Minerals Processing Symposium was held at the Faculty of Engineering, University of Stelenbosch on Friday, 8th August, 1986. This series was initiated in 1982, the symposia being held alternately in Cape Town and Stelenbosch. The South African Institute of Mining and Metallurgy has kindly agreed to sponsor this event for the next three years. Cokemaking On the initiative of the European Cokemaking Commitee, the First International Cokemaking Congress will be held in Essen (F.R. Germany) from 13th to 19th September, 1987. It is being organized by the Steinkohlenbergbauverein, together with the Verein Deutscher Eisenhitenleute.

Jan 1, 1986

By B. C. Alberts

This. paper indicates how the South African Iron and Steel Industrial Corporation Limited (Iscor), as a major consumer of raw materials, determines the tonnage and quality of essential raw materials required to satisfy an increasing demand for steel and how this led to the establishment of a coal mine with a highly sophisticated beneficiation plant in the Waterberg coalfield, near Ellisras in the Transvaal. The planning of the project, with specific reference to the limited reserves of metallurgical coal in South Africa, the quality and quantity of the coal to be produced, and the way in which the project was managed is discussed briefly.

Jan 1, 1982

By A. R. Barnes, C. W. P. Finn

The prereduction and smelting characteristics of UG-2 ore were studied and compared with those of Winterveld chromite ore. The UG-2 ore proved more reducible, and substantial prereduction (over 70 per cent reduction after 30 minutes at 1250oC) was obtained. No difficulty was experienced in the production oh high-carbon ferrochromium alloy containing 48 to 50 per cent chromium. Calculations of the energy balance show that UG-2 chromite has lower total energy requirements (both on the basis of unit of ferrochromium produced and of total chromium content). More than 50 per cent of the energy required for reduction can be supplied outside the smelting furnace.

Jan 1, 1983

By R. R. Mankowski

The work described here is an extension of current theory applied to obtaining the power dissipated at the wavefront of a transverse disturbance traveling along a mine hoisting cable. A previously derived empirical relation is adapted to the present problem, and is solved by use of a Lagrange-type reference frame moving with the wavefront. As a result of tie limitations inherent in the original relation, only a lower-bound for the domain of predicted power losses is defined. A qualitative assessment of conditions leading to the undesirable effects of internal frictional losses at the wavefronts are discussed in terms of the operating environment found on typical mining installations

Jan 1, 1990

By M. J. H. Tonkins, C. C. Crosson, G. Paterson

The development of drilling and blasting practice at Palabora Mining Company Limited by c. C. CROSSON, Pr. Eng., A.C.S.M. (Hons), BASe. (Min. Eng.) Toronto, M.!.M.M. (Member), M. J. H. TONKING, Pr. Eng., A.C.S.M., BASe. (Min. Eng.) Toronto, M.I.M.M. (Member), and G. PATERSON, B.Se. (Min. Eng.) Glasgow, M.!.M.M. (Visitor) Open-pit drilling and blasting practice at the Palabora Mining Company Limited is described, with particular reference to the development of aluminized slurry explosives. Rotary drilling of primary drill holes, drilling patterns, and blasting techniques for use with slurry explosives are described.

Jan 2, 1976

By E. J. Magri, R. M. Murray

This paper describes the application of linear programming to the monthly &apos;set up&apos; planning of stopers&apos; sections on two gold mines. On one of these mines, the purpose of the exercise was to maximize the total stoping production (measured in centares per month). On the other mine, the maximum stoping contribution (rands per month) was required. Maximization was to be achieved through improved planning, independently of the various other productivity improving activities that were taking place at the same time. The results to date show that, when linear programming is used, an average increase of about 9 per cent in stoping production (or contribution) can be obtained for these two mines.

Jan 1, 1978

By A. P. W. Briggs

Difficulties with the screening of large volumes of pulp to remove plus 600 /km material before the adsorption circuit and to retain plus 20-mesh carbon in the adsorption contactors have largely been solved, with the result that the plant can now handle its design throughput. The elution and electrowinning processes have been modified to simplify the circuit, but the regeneration of carbon remains unsatisfactory. The production of fine carbon in the plant can lead to increased gold losses, and this carbon must be collected and treated. Collection methods for fine carbon and some indications of the quantity of the carbon and its gold values are given.

Jan 1, 1983

By J. P. McDonald, P. L. Mattison, J. M. W. Mackenzie

A variety of processing problems in the hydrometallurgical extraction of uranium in the U.S.A. are contrasted with those in South Africa. In U.S. plants, for example, problems are often encountered in the separation of vanadium, molybdenum, and uranium, and in the contamination of the circuit with organic acids. South African plants often experience problems with dissolved silica in the feed, clarification of feeds, and problems associated with synthetic polyelectrolytes. Individual situations are examined, along with the analytical techniques that assist in solving specific problems. Successful approaches that have been applied to mechanical and chemical problems in&apos; uranium solvent-extraction plants are discussed.

Jan 1, 1981

By I. V. Samarasekera, E. B. Hawbolt

A review of recent work being conducted at the university of British Columbia on the modeling of the microstructural evolution during the hot rolling of steel is presented. A mathematical model of heat transfer was developed to describe the thermal field in a slab during rough and finish rolling. The model for rough rolling, discussed in this review, also simulates the growth of oxide scale on the slab surface. To quantify the heat transferred from the slab to the work rolls, instrumented samples of MSI3O4 L stainless steel, 0,05 per cent carbon steel, and 0,05 per cent carbon steel with 0,025 per cent

Jan 1, 1995

By D. Mark, S. R. Hunneyball

The ongoing revision of the Respirable Dust Regulations (RDR) by the UK coal mining industry includes the introduction of personal exposure monitoring for underground mines, rather than the fixed point sampling of workplaces. The initial choice CIP10 personal respirable sampler, failed during the underground trials because of the transfer of large non-respirable particles to the respirable dust deposit under vibration from man-riding belts, and of adverse effects of high winds and high dust loading on the flowrate through the sampler. These effects were validated in laboratory simulations of these conditions. A cyclone-based personal sampler is showing promise as an alternative.

Jan 1, 2003