Search Documents

By T. A. Muhlare

"Large quantities of slag are produced every year and dumped on slag heaps around the world, posing a potential environmental threat due to contained heavy metals content. Slags are waste minerals produced during furnace smelting of minerals. The contained values of base metals may be released into the environment under natural weathering conditions polluting ground and underground water. Copper losses into slag are a continuous problem in pyrometallurgical smelting operations. Due to shortage of ore concentrate, various mining operations have initiated the recovery of copper from dumped slag. The typical process uses crushing, milling and flotation. These operations create excessive liner wear rates during crushing and milling because the bond work index of copper slag is 22 kWh/t and this is considered a very hard slag. The process also has reduced flotation recoveries and requires high flotation reagent consumption. The present work shows that digestion of the milled copper slag slurry with concentrated sulphuric acid at a temperature of 250oC forms a solid cake and leaching of the solid cake with water is a possible option. However, the consumption of sulphuric acid can have a considerable cost on the recovery process. This can be limited by producing a leach residue containing gypsum and silicate materials as amorphous silica which are suitable for use as an additive for Portland cement. Laboratory results show that 90% copper recoveries can be achieved. The leaching is conducted to prevent silica gel formation and iron co-extraction. Leaching is optimum if silica gel-free solutions and good filterable residue are obtained. INTRODUCTION Slag is a waste by-product of smelting and converting operations in metallurgical plants. Both smelting and converting operations are aimed at iron separation from base metal sulphides in non-ferrous metallurgy. The iron sulphide component of the ore or concentrate is oxidized to iron oxide at higher temperatures in the molten form, and then fluxed with silica and other oxide rock minerals to produce fayalite (2FeO•SiO2) slag (Schlesinger et al., 2011). Slags are generally deposited on dumps and considered to be unreactive materials. Smelter copper slag contains significant concentrations of several potentially toxic elements, including arsenic, lead, cadmium, barium, zinc and copper. These elements can be released into the environment under natural weathering conditions and cause pollution of soils, surface waters and groundwater (David, 1998)."

Jan 1, 2015

By T. G. Carter

Support system design for tunnels and underground excavations has for many years relied heavily on the use of rock mass classification systems and the Hoek-Brown failure criterion as a means for characterizing rock mass behaviour. Because of their development, both the GSI system and the Hoek-Brown criterion admirably characterize most ?normal? rockmasses from the viewpoint of their behaviour for rock excavations. They, however, run into difficulties when applied at the two ends of the rock competence scale. This is largely because block size and incipient strength are such that rockmass behaviour in these domains tends not to be controlled by interblock shear strength but rather by material strength. At the low end of the rock competence scale (UCSi <<15 MPa and GSI generally <30) discontinuities play less of a role and rock mass strength tends to matrix strength. Similarly, at the high end of the scale (GSI >>65, mi>>15), because discontinuities are now widely spaced, block size becomes so significant that again, intact material behaviour rather than the fracturing becomes the dominant factor controlling rock mass strength. In this paper several case examples are presented to illustrate the application of the high-end (spalling) and low-end (weak ground) transition Hoek-Brown relationships proposed by Carter, Diederichs and Carvalho (2007) as a basis for better defining rockmass behaviour at the extreme ends of the rock competence scale.

Jan 1, 2008

By E. J. M. Jahnsen, I. Jauhari, T. Badrujaman, F. A. Stober, B. O. Wasmund, L. R. Nelson, T. Miraza, J. M. A. Geldenhuis, A. Taofik Hidyat

The role of dedicated operational support in the ramp-up and stabilisation of the FeNi-II furnace for ferro-nickel production at PT Antam?s smelter located in Pomalaa, Indonesia is described. The furnace was uprated to 32MW capability in a rebuild performed in 2005. This primarily involved installing a larger transformer, coupled with adoption of HATCH water-cooled copper plate, waffle and flanker coolers with integrated metal and slag tapblocks, HATCH air-cooled copper fin lower sidewall cooling and HATCH vertical sidewall binding system ? ?holddowns?. Following a smooth commissioning period, the progress in attaining the preliminary ramp-up target load of 24MW is described. This initial target was set by Antam, subject to some prevailing smelter equipment constraints, particularly kiln capacity. Stabilisation of the furnace operation is discussed, together with some of the specific commissioning and operational challenges surmounted by the joint Antam-HATCH team. These included: ?Mastering furnace integrity monitoring and operation with copper coolers, especially metal tapblock planned maintenance and repair strategies; ?Transition from traditional ?immersed electrode? to ?brush-arc? mode of operation approaching as closely as possible to the productive ?shielded-arc? mode of operation within existing equipment constraints; ?Reductant selection and control issues; ?Utilising the sophisticated furnace monitoring to provide detailed indication and warning of potentially destructive furnace upset conditions such as Si reversion and CO boils.

Jan 1, 2007

Caving of the second lift of the E26 orebody at Northparkes Mines was monitored with a comprehensive package of instrumentation, including an ISS seismic monitoring system. Seismicity was collected by an array of 19 triaxial accelerometers and 9 uniaxial geophones, giving a high quality seismic data set. The seismic response to block caving at Northparkes has been divided into two papers. The first paper focuses on the seismicity during undercutting. The second paper deals primarily with the seismicity during cave propagation during initial cave production. In this paper, traditional seismic monitoring concepts are applied to seismicity during cave mining. More than 40 000 seismic events were recorded during cave undercutting between February and January 2004. Events up to local magnitude +1.3 were recorded near the mine during undercutting, with event rates of up to 500 per day. Analysis of frequency-magnitude distributions, S-wave to P-wave energy, and temporal variations in event magnitude all gave insight into the seismicity recorded. In addition, a new technique, called apparent stress time history, was shown to be sensitive to stress change from undercut blasting, and useful to identify significant periods during cave development. A significant difference was identified between the cave back location and the halo of seismic events above the cave. Throughout the undercutting, the a seismic zone of loosening was typically 50 to 70 metres in vertical thickness. Based on the seismicity, a stress driven rock mass failure model is proposed. Early in the undercutting, seismicity and movements in the seismogenic zone were directly triggered by stress change from undercutting. Towards the end of undercutting, seismicity was virtually uncorrelated with undercut blasting, and likely due to the onset of cave initiation.

Jan 1, 2008

By A. C. Legg, M. T. Malema

Keywords: Pyrometallurgy, flash, smelting, furnace, nickel, copper, Botswana BCL Limited operates the only Flash Smelting Furnace on the African continent, at Selebi-Phikwe, situated in north-eastern Botswana. The furnace was commissioned in 1973 and produces a high-grade sulphide matte containing nickel, copper and cobalt, which is shipped to refineries in Zimbabwe and Norway for further processing. This paper outlines the recent process improvements and plant expansions that have resulted in a capacity increase from 40 000 to 60 000 tons per annum of metal production.

Jan 1, 2006

By K. Lombard

"‘Roof support awaiting time’ (RSAT) is a term used at Goedehoop Colliery’s Simunye Shaft to describe the potential production time lost due to the continuous miner (CM) standing idle waiting for roof support to catch up. Investigations revealed that in 2013, Simunye Shaft had approximately1400 hours of RSAT, which suggests that the mine could have potentially produced an additional 280 000 t of coal. This project consisted of two parts. Firstly, the causes of the high RSAT and means to improve the situation were investigated. Secondly, as insisted by mine management, the CM cutting sequence was investigated as a possible cause of high RSAT. Machine-related challenges due to the roofbolter installing support too slowly, geological conditions (mostly hard roof conditions and slips),logistical challenges pertaining to the CM cutting sequence, man-related challenges related to operator fatigue, re-support, operator inexperience, and the absence of support targets were identified as main contributors to RSAT. Furthermore, results showed that the roofbolters in the sections at Simunye Shaft are slower than the CMs. A target of 28% reduction in RSAT was set. Experts from Kennametal and Fletcher were consulted to find solutions for the identified causes. In total, eight solutions for RSAT were identified, but the solution that contributed most significantly to reducing RSAT was to use hard roof drill bits as a standard product at Simunye Shaft. Calculations showed that by using hard roof drill bits, RSAT can be reduced by 43%, which is more than the specified 28% target. The cutting sequences at Kriel, Greenside, and Simunye Shaft, togetherwith three newly developed cutting sequences, were simulated using the UCMS (Underground Coal Mining Simulation) program. A re-aligningprinciple was incorporated into the newly developed cutting sequences toalign the cutting sequences to general support work and to reduce RSAT. A decision matrix revealed that a cutting sequence in which boxing takesplace in R3 (third road to the right of the belt road) and in which the re-aligning principle has been incorporated will be the best option for Simunye Shaft. The recommended cutting sequence will lead to a 5% increase in production.The work presented in this paper was carried out as partial fullfilment for the degree BEng (Mining Engineering)"

Jan 1, 2015

By M. Gous

Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC arc furnace, titania slag, pig iron Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilisation and furnace stability, complemented by continuous improvement drives, will be the vehicle to drive performance in the short term, with longer-term performance enhancements due to strategic process development.

Jan 1, 2006

By R. Katzenbach, M. Vogler, U. Adamietz

Abstract The design of deep excavation pits in rock mass is dependent as well on the mechanical properties of the rock mass as for example the orientation and the type of discontinuities like bedding planes, joints and fissures, the length of the discontinuities (persistence), the grade of weathering, the strength of rock mass, and the shear strength in the discontinuities, etc., and also on the respective boundary conditions specific for the project, and here especially the geometrical boundary conditions. The basic mutual influences and interactions between these boundary conditions are explained and exemplary presented at an excavation pit with a depth of 18,5 m, situated at a slope with a surface near groundwater table. Résumé La planification des excavations profondes dépend aussi bien de la qualité mécanique du roc, par exemple la location de la texture de la surface de moindre résistance, le degré de rupture, le degré de décomposition, la dureté du roc et la résistance limitée au cisaillement de la texture de la surface de moindre résistance que des conditions limitées spécifiques pour le projet, ici en particulier des conditions limitées géométriques. Les influences et interactions essentielles et mutuelles entre les conditions limitées isolées seront expliquées et présentées à l’aide d’une excavation 18,5 m de profondeur, située sur une pente où le niveau des eaux souterraines est près de la surface. Kurzfassung Die Planung tiefer Baugruben im Fels hängt sowohl von den mechanischen Eigenschaften des Fels wie z.B. der räumlichen Lage des Trennflächengefüges, dem Durchtrennungsgrad, dem Verwitterungsgrad, der Gesteinsfestigkeit sowie der Scherfestigkeit des Trennflächengefüges als auch von den projektspezifischen Randbedingungen hier insbesondere von den geometrischen Randbedingungen ab. Die wesentlichen gegenseitigen Einflüsse und Interaktionen zwischen den einzelnen Randbedingungen werden aufgezeigt und an einer 18,5 m tiefen Baugrube in Hanglage mit oberflächennahem Grundwasser vorgestellt.

Jan 1, 2003

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 um. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By S. O. Bada

Coal samples taken from the No. 2 Seam and No. 4 Seam in a South African colliery were tested in a rotary triboelectrostatic separator. The two-stage triboelectrostatic separation results using the -177 µm size fraction reduced No. 2 Seam coal containing about 30.4 per cent ash to a clean product of 8.9 per cent and 13.1 per cent ash with combustible recoveries of 9.6 per cent and 30.7 per cent respectively. The same separation approach on No. 4 seam feed coal, which contained 36 per cent ash, produced a clean coal product with 10.8 per cent ash at a combustible recovery of 6.0 per cent. Petrographic tests show a significant improvement in the vitrinite content and a reduction in visible minerals encountered when using the triboelectrostatic separator, with about 53 per cent vitrinite reporting to the clean fraction for No. 2 Seam compared to the feed content of 21 per cent, and a 54 per cent vitrinite in the clean No. 4 Seam from a feed content of 21 per cent. Significant sulphur reductions were also observed after separation in both coal samples, with a better separation in the second-stage coal products.

Jan 1, 2012

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

By M. Shapiro, L. A. le Grange, B. Henning

A paper was presented by Bateman Minerals and Metals at INFACONX (2004) describing a simplified Computational Fluid Dynamics (CFD) Model for predicting the temperature and velocity distributions in all the fluid zones of a single electrode DC Furnace simultaneously with the temperature distributions in the refractory lining of the vessel. The boundary conditions imposed on the model consisted of the arc current, external surface film coefficients and ambient temperatures. The temperature and velocity distributions in the free-board, slag and metal were solved simultaneously by coupling across the interfaces between the fluids and transportation phenomena developing in the plasma arc. A simplified model was used to describe the ex-change of energy by radiation between the arc and surfaces enclosing the freeboard region. The strengths of this model were reported as being the ability to: ?Solve the different zones and transportation phenomena simultaneously without the need to transfer partial numerical results between different numerical analysis applications. ?Solve velocity and temperature distributions without assumptions regarding internal film coefficients and additional internal temperature boundary conditions. One of the disadvantages of the model was that the energy absorbed by the process was not modelled, resulting in vessel performance predictions under heat loss conditions only. Whilst this allowed potential problem areas such as localized refractory heating to be identified, the model was only capable of predicting how these could be improved by varying the overall geometry and materials of construction. This paper presents improvements in the application software and user defined subroutines of the model as follows: ?Incorporation of surface to gas, gas to gas and gas to surface radiation models to improve the accuracy of radiative heat transfer mechanisms within the freeboard. ?Incorporation of a process energy absorption model based on a theoretical temperature dependant enthalpy curve which incorporates melting, smelting and superheating in selected areas of the bath. This enables the effect of feed distribution and power to feed ratio changes to be estimated. The effects of a commercial arc at full power on the freeboard and slag can now be simulated with increased accuracy.

Jan 1, 2007

With the passing of Dr William Bleloch on 20th June 1991, we lost not only a colleague and a good friend but a man who made a very significant contribution to the industrial development of South Africa. He can rightly be called the father of the ekctrochemical and electro-metallurgical industries in this country, since his ideas and dedicated work were directly responsible for the development of these large industries as we know them today.

Jan 1, 1991

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By T. Mapeta, S. M. Rupprecht

Discussions on reasonable prospects for eventual economic extraction (RPEEE) include the CRIRSCO 2019 reporting template, JORC 2012, SAMREC 2016, CIM 2019 Guideline, and Regulation SK-1300. These reporting codes all conform to the principles of reasonable prospects for eventual economic extraction. To demonstrate that all mineral resources align with the RPEEE principles, the Competent Person is responsible for endorsing the mineral resource estimate. Moreover, establishing mineral resources and RPEEE requires technical input from numerous technical specialists, such as mining and geotechnical engineers, metallurgical engineers, social and environmental specialists, financial and governmental practitioners, and more. The aim is to improve the transparency of the disclosure of mineral resources and guarantee the investor or potential investor that the reporting of mineral resources is based on reliable technical, economic, environmental, social, and other relevant factors. This paper discusses the important protocols and definitions in some international reporting codes for the purposes of developing a guide memoire that will assist the Competent Person to interpret, establish and apply RPEEE appropriately and easily.

Jun 27, 2025

By M. Reuter, U. Boin

The target of the current metallurgical industry is to recycle and utilize all their by-products, so as to close the sustainable production loop. Slags are the important wastes and by-products of metallurgical industry, which have been treated, recycled and used worldwide. The present paper summarizes the current status of utilization of the various slags from ferrous and non-ferrous metal production, as well as waste incineration, and recycling of salt fluxes in secondary metal production. In addition, the environmental issues of the metallurgical slags are addressed. The metallurgical oxide slags have stone-like properties and, thus, their major applications are in civil engineering field. The slags should be recycled, modified and processed in a proper way, by taking the environmental impact into consideration. With the treatment of salt slags for melting aluminium scraps, as an example, the recycling and elution properties of the salt slags are discussed. Our research indicates that the viscosity of the salt flux is increased with addition of non-metallic components, that a certain percentage of fines remain in suspension, which determines the viscosity, affecting the settling of heavier materials. High slag viscosity will lead to more fine aluminium metal entrapped in the salt slag (may also be seen as a high temperature slurry), and thus increase the load of salt slag recycling. Keywords: recycling, environment, metallurgy, slags, fluxes, salts.

Jan 1, 2004

By Sverre Olsen, Kai Tang

The composition of ferromanganese slag is very important as it determines the slag/metal equilibrium relations including MnO content of final slag, melting relations and slag viscosity. The slag composition is further expected to influence the process temperature. The properties of ferromanganese slags are suitably described by its basicity and A/S mass ratios. The influence of slag basicity has been discussed in the previous papers. The present paper will discuss the effect of Al2O3 on melting relations, viscosity and MnO-content of final slag. This discussion will be based on assessed thermochemical databases and a recently developed viscosity model.

Jan 1, 2007

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007

By G. Howell, J. Wates, A. Coetzee, C. J. MacRobert

The Global Industry Standard on Tailings Management (GISTM) requires mining companies to make four key appointments as part of their tailings management structure. These four positions are an Accountable Executive with policymaking responsibilities, a Responsible Tailings Facility Engineer with operational responsibility, an Engineer of Record to ensure facilities are designed, operated, and closed safely, and an Independent Tailings Review Board to assess safety drivers regularly. Little guidance on the traits of these individuals is available in a South African context. Consequently, the tailings community of practice was surveyed to develop a table of ideal competencies and establish the flexibility in meeting these traits.

Jun 2, 2022

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002