Search Documents

By J. H. Potgieter

The method used to assess the reactivity of lime was evaluated to gauge it usefulness as a quality control tool. The effect of particle sizes, different lime and water masses for a fixed s:l ratio and the same for various s:l ratios on the reactivity values obtained, were investigated. An attempt to introduce the amount of grit produced during the slaking reaction as an additional measure of limeís quality and reactivity, proved to be unsuccessful. It was also found that the relative amount of lime slaked during the different tests was independent of the reactivity value of the lime. The investigation confirmed the usefulness of the accepted test procedure as are liable method to measure the reactivity of lime, despite various reservations expressed from a theoretical point of view.

Jan 1, 2002

The 100th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 13th August, 1997. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows and Past Presidents D.M. Jamieson, V.C. Robinson Fellows S. Goodwin, M.W. Johns Retired Fellows T.F. Muller, P.L. Nathan, N. Orsmond, R.J. Ortlepp, H.S. Sichel, K.E. Steele, W.B.L. Steuart, N.B. Vinson Member J.P. Hatfield Retired Members S.T. Baron, B.F. Pinder Retired Associate F.J.A. van Reenen In memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1997

By A. Burger Pintér

To be meaningful the sharing of ideas about the National Environmental Management Act (NEMA) and social issues within the context of Mining and Metallurgy (M&M) requires an honest scrutiny of the M&M/social environment relationship, both past and present. It is not a secret that this relationship has been and is fraught with difficulties. Thus from all perspectives (M&M, society and environmental and social consultants) such a dissection, that highlights the realities, both good and bad, is uncomfortable. For this section of the colloquium to have any value, the honest but difficult approach needs to be taken.

Jan 1, 2000

By J. A. Venter, M. K. G. Vermaak

There are practical indications that flotation recovery of palladium bismuth tellurides is poor. This work tested whether this can be caused by a lack of interaction of the collector with the telluride. Impedance measurements, voltammetry and Raman spectroscopy were performed to determine the interaction of dithiocarbonate collectors (KEX) with Pd-Bi-Te. Impedance measurements showed lower capacitance values in solutions containing KEX indicating the formation of a continuous surface layer. Anodic and cathodic polarization diagrams show the mixed potential tobe higher than the reversible potential of the xanthate-dixanthogen equilibrium reaction; hence the formation of dixanthogen on the surface is possible. Electrochemically controlled in situ Raman spectroscopy did indicate the presence of bulk diethyl dixanthogen on the surface. Raman spectroscopy has confirmed the co-presence of xanthate with dixanthogen, indicating that xanthate retains its molecular integrity when it adsorbs on the surface of the Pd-Bi-Te. As a result, the mineral surface is expected to be hydrophobic and a lack of collector interaction with the mineral is not the reason for low PGM recoveries experienced. Keywords: Raman spectroscopy; Pd-Bi-Te; ethyl xanthate; platinum flotation; Great Dyke; Pd-bearing bismutho-tellurides and moncheite.

Jan 1, 2004

The 102nd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 18th August, 1999. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows and Past Presidents D.D. Howat Life Fellows O. Deane, J.S. van Zijl Fellow A.A. Hejja Retired Fellows A.L. Forder, C.B. Parker, A.C. Petersen, F.W.J. Ross Members J.S. Stanko, D.H. Gray Retired Member P.K. Bredell Retired Associate I.S. van Eyssen In memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1999

By D. Boldini, R. Lackner, H. A. Mang

ABSTRACT: In this paper, the strong interaction between the hardening shotcrete lining and the surrounding ground in NATM tunneling is investigated by means of axisymmetric analyses, accounting for the three-dimensional nature of the excavation process. The effect of the hydration of shotcrete on strength, stiffness, chemical shrinkage as well as microcracking and creep are accounted for. For the description of the mechanical behavior of the ground, a multi-surface plasticity model is employed. The performed analyses of the excavation process provide insight into the influence of each phenomenon accounted for in the material model for shotcrete on the response of the ground-shotcrete compound structure. ZUSAMMENFASSUNG: In diesem Beitrag soll die Interaktion zwischen dem erhärtenden Spritzbeton und dem Boden auf der Basis axisymmetrischer Berechnungen untersucht werden. Derartige Berechnungen ermöglichen die Berücksichtigung des drei-dimensionalen Charakters des Vortriebprozesses. Die Auswirkung der Hydratation auf die Entwicklung der Festigkeit, Steifigkeit und der chemischen Schwindverzerrungen, sowie das Reißen und das Kriechen des Spritzbetons wurde berücksichtigt. Das mechanische Verhalten des Bodens wurde mittels eines Mehrflächenplastizitätsmodells simuliert. Die durchgeführten Berechnungen des Vortriebprozesses geben Einblicke in die Auswirkungen der Spritzbetoneigenschaften auf das Tragverhalten des Boden-Spritzbeton-Komposits. RÉSUMÉ: La stricte interaction entre le soutènement en béton projeté durcissant et le terrain dans un tunnel creusé avec la NATM est étudiée par des analyses axisymétriques, compte tenu de la nature tridimensionnelle des processus de creusement. Les effets de l’hydratation du béton sur la résistance, la rigidité et la contraction chimique, ainsi que sur la micro-fissuration et le fluage, sont mis en compte. Pour la description du comportement mécanique du terrain on emploie un modèle de plasticité multi-surface. Les analyses conduites mettent en évidence l’influence de chaque phénomène considéré dans le modèle constitutif du béton projeté sur la réponse de la structure composite terrain-béton projeté.

Jan 1, 2003

By M. F. Handley

Sequential grid mining has been employed as the primary mining strategy at the AngloGold West Wits Elandsrand Mine since the inception of stoping operations from the sub-vertical shaft system in 1988. Little has been published on sequential grid mining as a mining strategy since, and the purpose of this paper is to describe sequential grid mining, its history, its implementation at Elandsrand, and the outcome to date. The results obtained using sequential grid mining have been evaluated from seismic data, productivity statistics, and rock related accident statistics. Comparisons with neighbouring mines namely Western Deep Levels and Deelkraal, have been made to substantiate the improved conditions observed at Elandsrand, and to compare sequential grid mining directly with longwall mining in similar conditions and at similar depths. Sequential grid mMining is shown to be cost-effective, more flexible, and safer than long wall mining in similar conditions, at least on the Ventersdorp Contact Reef in the western part of the Carletonville Goldfield. More work is necessary to establish it as the favoured mining strategy at depths exceeding 3000 metres, and for reefs other than the Ventersdorp Contact Reef.

Jan 1, 2000

The Gordonsville Operation of Pasminco US Inc. along with the Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech studied, developed and implemented a pilot scale hydrometallurgical facility for the industrial recovery of germanium and gallium. This paper describes the joint testing and engineering program that culminated in this successful process. 1. Introduction The Pasminco US Inc. (PAS), Gordonsville Operation, has been producing zinc concentrate continuously since 1975. Within the zinc concentrate, several byproduct elements were found to be significantly concentrated including gallium and germanium. The gallium and germanium replace zinc and other metals within the crystal lattice structure of the zinc mineral (sphalerite) and are concentrated in the same manner as the zinc mineral. This concentrate is then sent to the Pasminco Clarksville Zinc Refinery for further processing. Within the hydrometallurgical zinc-processing plant at Clarksville, a residue is formed that contains a majority of the impurities that would otherwise contaminate or hinder the zinc process. Approximately 5,000 tons of residue is formed annually containing approximately 0.80% gallium and 0.60% germanium along with significant quantities of iron, zinc, silica, and lead. Pasminco currently sells this residue for the germanium value. Until recently, no revenue for the gallium was obtained from the sale of the residue.

Jan 1, 2008

By D. E. Ng?andu

The experience of Mufulira concentrator, of the Zambia Consolidated Copper Mines Limited, with underground mine drainage water, which is used in milling operations is discussed. It is shown that the underground mine water has a deleterious effect on flotation performance. The adverse effect of the underground water was successfully negated by adding lime into the primary ball mills and increasing the pH of the slurry, from a ?natural? pH of 8 to the flotation pH of 10.5. Traditionally, the pH modifier, quicklime, had been added downstream of the milling. Changing the lime addition point further reduced lime consumption by 50%,?a key issue as lime accounted for over 60% of the Mufulira flotation reagent costs. The nature of the effect of the underground water at Mufulira, particularly the sensitivity of the flotation to the pH at which the milling was conducted, characterized galvanic interaction. A large-scale plant situation is presented in which the desired electro-chemical response in the flotation was achieved, by a deliberate manipulation of the milling environment. The experience provides practical testimony of a more fundamental role for the milling process, other than the mere physical preparation, i.e. size reduction and liberation, of mineral particles prior to flotation.

Jan 1, 2001

By H. G. Denkhaus

Please allow me the temerity to reply to your reply to my contribution as follows: A fracture is brittle if plastic deformation is absent or, conversely a fracture is ductile if plastic deformation is present. Consequently, brittleness is specified by the degree of plastic deformation at fracture. This is the generally accepted definition. If other material properties (e.g. the quorient or the product of the uniaxial compressive and tensile strengths) under certain conditions are influenced by brittleness, or brittleness by them, these should not be called brittleness. If the one or the other author does that, he simply uses imprecise language. Even your remark, that ?Inyang and Pitt (1990) stated that the ratio of the compressive strength (sc/st) is directly proportional to brittleness?, confirms that the two quantities are not considered the same. For example:? The well known definition that a material is linear?elastic if the strain is directly proportional to the stress?does not mean that stress (measured in MPa) and strain (measured in %) are the same thing.

Jan 1, 2003

By J. Engelbrecht

South Africa?s re-entry into the fast moving and competitive global economy calls for some careful strategic planning and a good deal of co-operation between suppliers and end-users. The issues that need addressing are generally well known and include: ?South Africa was ranked 45th out of 46 i.r.o. productivity ?SMMEs contribute 1% to exports compared to 40-60% for the ?tigers? ?High unemployment ?Limited skills of the majority of workers ?Slow growth rate of the economy ?The vast majority of suppliers are not world-class ?The vast majority of suppliers are not export or marketing orientated. In order to survive, all parties, i.e. government, labour and business, will have to play their part.

Jan 1, 1999

Open cast mining has been practiced in South Africa since the late1970s under near ideal geotechnical conditions. In the past decade, with the exhaustion of the traditional South African coal fields, geotechnical conditions have deteriorated. In addition, the nature of the open cast coal mining industry is changing from the conventional strip mining of virgin coal seams to the extraction of underground coal pillars by buffer blasted highwalls. These industry changes have resulted in the need to re-examine the manner in which geotechnical engineering is applied to highwall design. This paper proposes a geotechnical design rationale for open cast highwalls. Furthermore, the rationale takes cognizance of the various geotechnical hazards associated with conventional strip mining and pillar extraction by buffer blasted highwalls. The need to use geotechnical domain models and blasting geotechnics, as proactive tools for rock fall reduction, are also discussed.

Jan 1, 2001

By S. K. Murphy, S. M. Spottiswoode, A. M. Milev, D. Geyser

A portable, stand-alone instrument especially designed for recording strong ground motion was used in this study to create a large database of peak particle velocities measured underground. A total number of 39 sites located in stopes mining Carbon Leader and Ventersdorp Contact Reefs were investigated. Peak particle velocities whith values up to 3 m/s were recorded at some sites. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response. The maximum site response was obtained for source radii of between 5 m and 30 m and events locating within 200 m of the site. The extreme values of peak particle velocities were obtained in cases were the face-area lay within the source radius. Un instrument portable unique spécifiquement conçu pour enregistrer les mouvements dynamiques des terrains, a été utilisé dans cette étude pour créer une base de données importante sur la vélocité maximum des particules, mesurée en souterrain. Un nombre total de 39 sites situés dans les excavations exploitant les récifs appelés ‘Carbon Leader et Ventersdorp Contact Reefs’, a été investigué. Une vélocité maximale avec des valeurs allant jusqu’ à 3 m/s a été enregistrée sur certains sites. Les données enregistrées sur le bord de l’excavation ont été comparées aux données enregistrées par les réseaux séismiques de la mine pour déterminer la réponse du site. La réponse maximum du site a été obtenue pour des sources de rayons entre 5 m et 30 m et des évènements situés dans les 200 m du site. Les valeurs extrêmes de vélocités maximales ont été obtenues pour les cas où la zone de face se trouve à l’intérieur du rayon de la source. Ein mobiles, alleinstehendes Instrument, speziell entworfen um starke Formationsbewegungen aufzuzeichnen, wurde in dieser Studie verwendet um eine große Datenbank von Partikelspitzengeschwindigkeiten, die Untertage gemessen wurden, aufzuzeichnen. Eine Gesamtanzahl von 39 Aufstellungsorten in den Schichtabbauorten vom Carbon Leader und Ventersdorp Contact Reef wurden untersucht. Partikelspitzengeschwindigkeiten mit Werten bis zu 3 m/s wurden an einigen Standorten aufgezeichnet Die an der Oberfläche des Grubenraumes aufgezeichneten Daten wurden mit jenen Daten verglichen, die vom seismischen Netzwerk der Grube notiert wurden, um die örtliche Reaktion des Standortes zu bestimmen. Die maximale Standortreaktion wurde für Ursprungsradien von zwischen 5 m und 30 m erhalten und Ereignissen die sich innerhalb von 200 m vom Standort befanden. Die extremen Werte der Partikelhöchstgeschwindigkeiten wurdenin jenen Fällen erreicht wo sich der Abbaubereich innerhalb des Ursprungsradiuses befand.

Jan 1, 2003

By W. Kint

More than 10 years ago, one of MECS?s current partners KVT developed the so called SULFOX process for cleaning waste gases containing sulfuric compounds. In this Wet Acid Process (WAP) compounds such as SO2 and H2S, CS2, COS are oxidized over catalyst bed(s) to SO3 and finally sulfuric acid is formed. The individual plants are designed according the feed gas concentrations and customers requirements to keep the investment and operating costs as low as possible. MECS strongly believes the technology we propose will meet all your expectations. Thanks to our vast experience in the construction of sulfuric acid plants (MECS built over 800 sulfuric acid plants worldwide) we were able to design you a very reliable installation. MECS is offering the metallurgical industry, besides our conventional acid plant technology (for strong SO2) and our DynaWave? scrubbing technology (for very low SO2), a SULFOX wet acid plant (for the mid range SO2 concentrations) including an optional upstream DynaWave gas cleaning plant if required. See the figure below. Besides providing advanced technology, MECS is the only company who designs and manufactures its own key critical equipment. We manufacture our own catalyst, mist eliminators, acid distributors and coolers. Because of our in-depth technology knowledge, we understand the critical aspects necessary for making optimum equipment designs. With this combined supply of technology and key critical equipment, we can make a single overall guarantee second to none other in the world.

Jan 1, 2009

By H. Willenberg, J. S. Coggan

ABSTRACT: Although individually both continuum and discontinuum numerical analyses provide useful means to analyze rock slope stability problems, complex failures typically involve mechanisms related to both existing discontinuities (i.e. discontinuum) and deformation and brittle fracture of intact rock (i.e. continuum). One such example is the 1991 Randa rockslide in the southwestern Swiss Alps, where failure involved several complex mechanisms, which require the consideration of progressive failure and rock mass strength degradation. This paper presents results from a series of hybrid finite-/discrete-element models directed towards the explicit modelling of brittle fracturing in natural rock slopes, enabling the modelling of progressive failure, from initiation, through to the development of catastrophic failure, transport and deposition. RÉSUMÉ: Si les modélisations numériques de type continu ou discontinu fournissent des outils utiles pour l’analyse de problèmes de stabilité de pentes rocheuses, elles montrent de sérieuses limitations lorsque des mécanismes de rupture complexes impliquent des processus liés autant aux discontinuités préexistantes qu’au développement progressif de nouvelles fractures. Ceci se retrouve typiquement dans l’exemple de l’éboulement de 1991 à Randa dans les Alpes suisses du sud-ouest, où la rupture a impliqué plusieurs mécanismes complexes nécessitant la prise en considération de la fracturation progressive ainsi que de la dégradation de la résistance des masses rocheuses. Cet article présente des résultats provisoires d'une série de modèles hybrides orientés vers la modélisation explicite de la fracturation de pentes naturelles, permettant la modélisation de fractures progressive de leur initiation jusqu’à leur développement, leur rupture catastrophique, leur transport et leur déposition. ZUSAMMENFASSUNG: Obwohl numerische Kontinuum- und Diskontinuum-Berechnungen einzeln nützliche Ergebnisse zur Stabilitätsanalyse von Felshängen liefern, sind komplexe Felsrutschungen typischerweise mit Mechanismen verbunden, die sowohl durch bestehende Trennflächen (s.a. Diskontinuum-Ansatz) als auch durch die Deformation und das Versagen intakter Felsbereiche (s.a. Kontinuum-Ansatz) bedingt werden. Ein Beispiel für einen solchen Sachverhalt ist der Bergsturz von Randa 1991 im südwestlichen Teil der Schweizer Alpen, bei dem die Rutschung mehrere komplexe Mechanismen umfasste, so dass “progressive failure” und Verminderung der Gebirgsfestigkeit in Betracht gezogen werden müssen. Dieser Artikel beschreibt vorläufige Ergebnisse einer Reihe von hybriden Modellrechnungen (Finite-/Diskrete-Elemente). Diese haben zum Ziel, explizit das bruchhafte Versagen natürlicher Felshänge zu modellieren, wobei das progressives Versagen im ganzen modelliert wird, von der Anfangsphase über die Entwicklung zum katastrophalen Versagen und den Transport und die Ablagerung der Rutschmassen.

Jan 1, 2003

By F. H. Cornet, D. Ask, O. Stephansson

We have conducted a stress analysis of overcoring stress measurements undertaken at the Zedex Test Site (ZTS) in the Äspö HRL, Sweden. Two different types of overcoring cells have been used at the site: the 9-gauge Borre Probe (CSIR-type) and the 12-gauge CSIRO HI cell. Inversion programs based on the least-squares criterion were developed and calibrated. The primary and secondary stress field in the ZTS were back-calculated using strain data from individual cells as well as from combining data from both cells. We propose that the combination of strain data from the two cells significantly improves the determination of the stress field. A striking result is the good agreement between the re-analysed overcoring data and the existing hydraulic fracturing data. The deviations for the horizontal stresses between the re-analyzed overcoring data and the existing hydraulic fracturing data are approximately 3 MPa. The deviation in the orientation of maximum horizontal stress is approximately 10-20°. Nous avons analysé les résultats de mesures de contrainte par surcarottage réalisées sur le site Zedex, du laboratoire souterrain HRL d’Aspö, en suède. Deux types de cellule de mesure ont été utilisés sur ce site : la cellule à 9 jauges (du type CSIR) et la cellule à 12 jauges (du type CSIRO HI). Un programme d’inversion mettant en œuvre une norme par moindres carrés a été développé et validé. Les champs de contrainte primaires et secondaires du site Zedex ont été évalués d’une part en considérant chaque mesure isolément, d’autre part en intégrant l’ensemble des données de déformation dans une inversion unique. Nos résultats suggèrent que l‘association des diverses mesures dans une intégration unique améliore nettement la détermination du champ de contrainte. Un résultat intéressant est le bon accord entre ces nouveaux résultats et les résultats des mesures par fracturation hydraulique. Les écarts sur l’amplitude des contraintes horizontales est de l’ordre de 3 Mpa, les écarts sur les orientations de l’ordre de 10-20°. Auf dem Zedex Test Gelände im Äspö Festgesteinslabor (HRL) wurde eine Spannungsanalyse mittels Overcoring Spannungsmessungen durchgeführt. Hierzu wurden zwei verschiedene Methoden verwendet: das 9-kanal Borre Gerät (CSIR- Ausführung) und die 12-Kanal CSIRO HI Zelle. Inversionsprogramme, die auf dem “least-squares”- Kriterium basieren, wurden entwickelt und kalibriert. Das primäre und sekundäre Spannungsfeld des Zedex Test Geländes wurde sowohl aus Verformungsdaten individueller Zellen als auch aus Kombination beider Zellen ermittelt. Wir nehmen an, daß die Kombination der Messergebnisse beider Geräte die Bestimmung des Spannungsfeldes signifikant verbessert. Überzeugender Beweis hierfür ist die gute Übereinstimmung der überprüften Overcoring Daten und Ergebnisse aus existierenden Hydraulic Fracturing Versuchen. Die Abweichungen der horizontalen Spannungen aus beiden Datensätzen ist etwa 3 MPa und Abweichungen der Orientierung der größten Horizontalspannung liegen bei etwa 10-20°.

Jan 1, 2003

A well known rock mass classification system has been altered slightly to address the issues found under remnant mining conditions. By detail study of the expected fracture patterns and local geology, the rock mass is classified to indicate the condition of the hanging wall prior to mining. The risk level of each mining step is evaluated by calculating input parameters for computer simulations from the actual rock mass condition. Seismic activity is catered for by the understanding that large event rates and large magnitude events reduce the quality of the local rock mass and that the rock mass stiffness should be adapted accordingly. A case study is presented to test parts of the protocol. Un système connu de classification des masses rocheuses a été légèrement modifié pour faire face aux questions posées par les conditions d’extraction de débris. Une étude détaillée des diagrammes de fragmentation et de la géologie locale permet de classer la masse rocheuse pour indiquer la condition du toit avant l’extraction. Le niveau de risque de chaque étape minière est évalué en calculant les paramètres d’entrée pour simulation par ordinateur à partir de la condition réelle de la masse rocheuse. L’activité sismique est prise en compte avec la réalisation que les taux de larges évènements et les évènements de large magnitude réduisent la qualité de la masse rocheuse locale et que la raideur de la masse rocheuse doit donc être adaptée. Une étude de cas est présentée pour tester des sections du protocole. Ein sehr bekanntes Gesteinsmassenklassifikationssystem wurde abgeändert um die Probleme zu behandeln die unter Restabbaukonditionen angetroffen werden. Durch detaillierstes Studium der der zu erwartenden Bruchmuster und der lokalen geologischen Verhältnisse wird die Gesteinsmasse in Hinblick auf die Konditionen der Flözoberseite klassifiziert. Das Risikoniveau für jeden Abbauschritt wird durch die Eingabeparameter aktuellen Gesteinsmassenkondition für die Computersimulation evaluiert. Für die Seismische Aktivitäten wird Sorge getragen durch das Verständnis, daß große Ereignisraten und Ereignisse hoher Größenklassen die Qualität der lokalen Gesteinsmasse reduzieren und daß die Gesteinsmassensteifheit entsprechend adaptiert werden sollte. Eine Fallstudie um Teile des Protokolls zu testen wird präsentiert.

Jan 1, 2003

By M. A. W. Bryson

Platinum group metals are extracted almost exclusively in South Africa from three very different zones in the Bushveld Igneous Complex, called the Plat, Merensky, and the UG-2 reefs. The Plat reef is currently being exploited only by Anglo American Platinum, whereas the Merensky reef is exploited by them, Impala Platinum, Northam, and Lonplats. The UG-2 reef, on the other hand, is also processed by these producers, but Kroondal and Barplats have operations that exclusively treat ore from this reef. At present the extraction of pgms from ores in South Africa follows the traditional route of upgrading to a concentrate in a minerals processing circuit, further upgrading to a matte in a smelter, and final upgrading and separation of the individual metals in a refinery. Thus all operations that extract pgms require a minerals processing circuit, the design and performance of which is a topic of much interest, as it is a poorly understood and not a very efficient process in relative terms, compared to the other processes. Recoveries across the minerals processing circuit of between 75 and 90% are the norm.

Jan 1, 2004

By K. I. Afewu

A modified approach to the implementation of Gy?s sampling theory is discussed and used to design a procedure for sampling crushed gold ore feed to metallurgical process plants. The approach involves calibration of certain ore-specific parameters. These parameters were calibrated for two different crushed gold ores en route to grinding mills in process plants. The model predictions were compared with the predictions from Gy?s original model. Far smaller masses of samples are required by the modified model than by Gy?s model at the same relative variance. The representativeness of the sampling procedure if normally distributed errors are assumed was also calculated. These procedures and evaluations lead to significant savings on cost of handling and preparation of the samples and to a quantifiable degree of confidence in the analytical results for the process plant.

Jan 1, 1998

Existing processes for the recovery of platinum group metals (PGM) from UG-2 ores place stringent requirements with regard to chromite content upon feed material to the plant. An alternative hydrometallurgical process for which this is not an issue is proposed that involves reductive roasting of the ore followed by leaching with HCl/chlorine, ion exchange, and recovery of PGM from the ion exchange eluate by reduction. Problems associated with leaching of PGM are discussed and results of laboratory testwork for each of the process steps are given.

Jan 1, 2004