Search Documents

By B. J. Scheiner

The Bureau of Mines investigated an electrolytic technique for oxidizing ore slurried with brine to determine its effectiveness in extracting mercury from ores. Optimization experiments conducted on a 2.5-pound-mercury-per-ton ore resulted in 95 percent mercury extraction with operating conditions of 30° C, a current density of 0.5 ampere per square inch, and a treatment time of 3.5 hours. Corresponding power consumption amounted to 38 kilowatt-hours per ton of ore treated. Amenability experiments conducted on 62 different mercury ores resulted in 90 to 99 percent mercury dissolution from ores containing 0.6 to 20 pounds of mercury per ton of ore, Treatment time ranged from 1 to 7 hours in 4-to 20-percent sodium chloride solutions, and power consumption was in the range of 10 to 50 kilowatt-hours per ton of ore. Pilot mill experiments in a 100-to 200-pound-per-hour extraction plant have been in progress to quantify power and reagent requirements. These data will be reported in a subsequent publication.

Jan 1, 1973

By W. E. Lamont

The Bureau of Mines studied the potential for recovering marketable barite concentrates that meet oil well drilling-mud specifications from barite waste pond materials. The study was conducted as part of the Bureau's research program to conserve domestic mineral resources by advancing mineral recycling technology. The samples, which were obtained from Georgia, Nevada, Missouri, and Illinois, varied widely in character, particle size, and barite content. The samples were treated with sodium silicate and sodium cetyl-stearyl sulfate and then floated. The flotation flow sheet was modified to reject barren coarse and/or slime fractions from some of the samples, and one feed sample had to be scrubbed prior to flotation to remove residual flotation reagents. The cleaned concentrates had BaS04 contents ranging from 95.0 to 96.9 percent, while recovering 81.2 to 95.9 percent of the barite in the feed. The specific gravity of each concentrate exceeded the specification of 4.2. The removal of the flotation reagents from the flotation concentrate was not investigated.

Jan 1, 1982

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 B. t. u. compared with 597,000 B. t. u. in 1936. These amounts represent roughly the heat obtainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at refineries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels were 11 percent higher than in 1930; the average operating ratio was 83 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 638,149 billion B. t. u. in 1936 to 663,966 billion B. t. u. in 1937.

Jan 1, 1938

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938

Decrease the dust concentrations at the shearer and reduce downtime associated with spray system maintenance. Approach Increase the quantity and quality of the water supply on longwall faces by decreasing pressure losses, Increasing pump capacity, and installing a "non-clogging" filtration system. How It Works Water sprays and ventilation are two of the primary methods of dust control on longwall operations. Increasing the quantity and quality of the water supply to spray systems is one of the more effective and least costly dust control methods that operators have at their disposal, yet this method is largely ignored. Poorly positioned spray nozzles operating at low pressures (and flows) which plug frequently cannot be effective. Water supply system Improvements should be a fundamental part of all longwall dust control plans. Upgrading a water supply system may require one or more of the following improvements depending upon where a particular system may be deficient: Increasing pump capacity for additional flow and pressure; increasing line sizes to decrease pressure losses: and, decreasing maintenance downtime and Improving water quality by installing a "non-clogging" filtration system.

Jan 1, 1981

By F. J. Smith, W. A. Gallagher, C. A. Herbert

"INTRODUCTION A fire started about 10 a.m., November 10, 1947, at the Kings mine, Princeton Mining Co., Princeton, Ind., about 1,800 feet inby the main shaft bottom on the main west haulage road at a point estimated to be 2 miles from the faces of the main west entries. No lives were lost, as 27 men escaped from the mine after a series of explosions, which necessitated sealing the mine on the surface. This information circular shows"" how adverse conditions might be overcome, when reopening a sealed mine, by expert planning and close cooperation on the part of various organizations. Conditions found in the mine after it was reopened were comparable to the worst that had been anticipated, yet the mine was recovered with comparatively little difficulty and a minimum of risk. The open workings in the mine covered a vast area, but most of the mine resumed production of coal after being sealed for only 37 days.The information contained herein also points to the desirability of adhering as closely as possible to a predetermined schedule of operations."

Feb 1, 1949

By Launa G. Mallett, Dana Reinke, Charles Vaught, Michael J. Brnich

As mines become safer and major disasters fewer, the number of experienced emergency responders is decreasing. This decrease will create a gap in response expertise which could have serious ramifications during future mine disasters. While working toward safety goals which may make emergency response obsolete, it would be reckless not to acknowledge that the potential for disaster still exists and that the protection of miners in such circumstances must remain a priority. The Mine Emergency Response Interactive Training Simulation (MERITS) is a computerized mine emergency simulation that meets a variety of needs. It allows personnel in leadership positions to test their knowledge and skill. Groups of individuals composed of representatives from mining companies, labor, and government agencies can practice working together during the simulated mine emergency much in the same way an actual emergency would require. An individual could also run the program to enhance his or her response skills. With this training tool, responders will be able to learn from their mistakes before facing situations with potentially catastrophic consequences. This paper discusses MERITS and its use in providing command center training.

By John D. Corrick

A dilute sulfuric-acid leach was developed for extracting lead and copper from lead blast furnace mattes and the chemistry was defined. The possible application of Ferrobacillus ferrooxidans to the problem of salvaging lead and copper from blast furnace mattes was also investigated. Operating conditions were varied to determine their effect on the oxidation and hence extraction of lead and copper from the matte. Conditions varied were temperature, pH, reaction time, aeration in the slurry, and particle size of the matte. A set of optimum conditions were developed that resulted in maximum lead and copper sulfide oxidation. Tests employing these optimum conditions resulted in 82.3 percent of the lead and 98.7 percent of the copper being extracted by a dilute acid leach, while maximum lead and copper extracted using F. ferrooxidans was 69.8 percent of the lead and 78.4 percent of the copper. Tests conducted with a different sample of blast furnace matte indicated that the dilute acid leach might have wide application in extracting lead and copper from other such blast furnace mattes.

Jan 1, 1968

By C. H. Elder, M. C. Irani

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand- stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By Donald R. Irving

ALTHOUGH the quantity of material handled at metal and nonmetal mines in the United States in 1962 was 2.7 billion tons, the same as in 1961, a larger proportion was waste. At metal mines, crude ore production declined 1 million tons and waste output rose more than 18 million tons; at nonmetal mines crude ore production declined 6 million tons and waste output rose 36 million tons. Copper and iron ore producers increased their share of crude ore and material handled from about three-fourths to four-fifths of the national metals total, and sand and gravel and stone producers in-creased their share of the nonmetals total, also from three-fourths to four-fifths. Six States-Arizona, California, Florida, Michigan, Minnesota, and Utah-each handled more than 100 million tons of ore and waste, and together they accounted for 43 percent of the U.S. total. When the large-volume construction materials (sand and gravel and stone) were excluded from the totals, four States-Arizona, Florida, Minnesota, and Utah-supplied over half of the material handled.

Jan 1, 1963

Federal lands often contain extensive mineral resources and decisions affecting access to those lands are made with knowledge of the possible minerals-related consequences. Information is provided to the Bureau of Land Management (BLM) in this report for use in preparing environmental impact statements on the Western Mojave Management Area (WMMA) and the Desert Tortoise Priority Habitat (DTPH). To augment U.S. Bureau of Mines (USBM) efforts such as the Mineral Assessment of the Planned Foil Irwin Expansion, Modified Silurian Valley Alternative, San Bernardino County, California which is in progress, and the Economic Analysis of the Minerals Potential of the East Mojave National Scenic Area; California, the USBM studied mineral deposits and estimated the potential impacts of mining in a segment of the California desert; the 8.7-million-acre WMMA, an area which includes the 1.2-million-acre Desert Tortoise Priority Habitat (DTPH). In addition, this information is intended to assist administrators, legislators, and the concerned public in understanding the economic importance of mineral resources in the California desert, especially that portion designated as the WMMA. See figure 1.

Jan 1, 1993

By D. R. Tesarik

An instrumentation and numeric modeling study was conducted by the Bureau of Mines at the Magmont Mine in Bixby, MO. An isolated section of this room-and-pillar mine was monitored with borehole and closure extensometers during a pillar recovery program to determine stress redistribution. In situ stress measurements were taken in the rib before pillar extraction began. Sample cores from the boreholes were taken for analysis of the properties of the host rock in the laboratory. The extensometers recorded no measurable displacements during most of the operation. Two-dimensional, finite-element; three-dimensional, finite-element; and three-dimensional displace-ment discontinuity codes were used to model the area of study. The finite-element models were run with two initial stress conditions, i.e., stress due to gravity only and stress obtained by in situ measurements. Horizontal stresses in the models reduced the calculated factor-of-safety in the mine back by up to a factor of 10, but did not have a significant effect on calculated pillar stability.

Jan 1, 1989

By Robert D. Schmidt

This Bureau of Mines report describes the development and application of a computer model for simulating the hydrological activity associated with in situ leaching. The model is intended to provide uranium resource developers with a description of the flow behavior of leachants and ground water during the development, production, and restoration phases of a leaching operation involving an arbitrary pattern of injection and recovery wells. Different aquifer environments are modeled, using a closed-form solution to the partial differential equation that describes three-dimensional changes in piezometric head as a result of pumping from leachant injection and recovery wells. The computer program can model a maximum of, 50 arbitarily located wells. Numerical techniques involving difference quotients and Taylor expansions about time points are used to derive time, velocity, areal sweep, and fluid volume parameters associated with leaching hydraulics. These parameters are output by the program in graphic and tabular formats. Other numeric methods insure that the program running time is minimized without significantly affect-ing the accuracy of results.

Jan 1, 1980

By M. J. Mechling, H. J. Sloman

"INTRODUCTION The practicability of providing safer methods of underground transportation for mine workmen and officials has been given much thought in recent years by advocates of safety, health, and efficiency. Numerous fatalities and disabling injuries have resulted from falls of roof, personal contact with both electrical conductors and timbers, and improper position or conduct of passengers while they were in man-trips. Unfavorable atmospheric exposure due to high-velocity air currents and sudden changes in temperature may adversely affect the health of mine workmen if they are transported in unprotected Cars.Recent installations of protected, man-trip cars, wherein such cars have been utilized to haul men to and from their stations in the mine, have resulted in a large reduction in exposure to haulage hazards. Where special-built cars have been used the probability of injuries to men during transportation in man-trips has been decreased, and the morale of the employees has been improved. A number of man-trip cars are in service in the coal-mining regions; those described in this circular are typical examples of a few installations."

Feb 1, 1948

By T. O. Llewellyn

The Bureau of Mines, as part of its goal to develop technology that can conserve domestic mineral resources investigated beneficiation methods for recovering phosphate minerals from two Southern Florida deposits with high magnesium content. Chemical analyses of sized fractions indicated that no coarse pebble concentrate could be produced from either deposit. Conventional fatty acid-fuel oil batch flotation tests on two phosphate samples, analyzing 6.8 and 8.5 pct P205, yielded concentrates containing 28.97 to 29.80 pct P20S at recoveries ranging from 72.4 to 76.9 pct of the flotation feed. The MgO content ranged from 1.20 to 1.36 pct. Bubbling S02 gas through an aqueous concentrate slurry, further reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 pct, but with a concomitant loss in the phosphate recovery. Settling characteristics of slimes from both phosphate samples showed a slow settling rate, which is a typical characteristic of other slimes in the region.

Jan 1, 1981

By R. A. Beall

A series of 45 zirconium ingots has been cast by the consumable electrode arc melting process with the object of analyzing the effects of power input from 50 to 230 kilowatts and reduced pressure furnace atmosphere to improve the quality of regular 8-inch-diameter production ingots made thereby. Electrode consumption rate, molten pool volume, melting efficiency, sidewall quality, arc stability, and yield efficiency are considered. The use of direct current and alternating current is studied. In conclusion, reduced pressure furnace operation is shown to promote electrical efficiency, ingot homogeneity, high metal yield, and are stability. INTRODUCTION Zirconium is a particularly difficult metal to melt because of its affinity for atmospheric gases and its solvent properties when molten. In addition, zirconium sponge as produced by the boll process contains minor amounts of magnesium chloride, which cause severe spattering luring melting, because of these difficulties with zirconium, and its sister metal titanium, near techniques have been developed to permit production of commercial size ingots. Among the more promising is the consumable electrode arc melting method.

Jan 1, 1955

By Bill M. Stewart

The Bureau of Mines conducted laboratory tests to determine the effects on the physical properties of coarse coal waste of adding large amounts of fine coal waste. Maximum laboratory dry density, optimum moisture content, shear strength, and permeability tests were conducted on samples that contained 18 to 60 pct minus No.4 (U.S. Standard sieve size) coal waste. For the nonslaky materials, maximum laboratory densities were highest and permeabilities lowest when the samples contained between 30 and 40 pct minus No.4. Shear strength increased rapidly when the proportion of minus No. 4 was increased from 20 to 40 pct, but then increased only slightly or leveled off when the minus No. 4 was increased to 60 pct. Optimum moisture content and permeability were the physical properties most affected by the addition of fines. Optimum moisture content increased as much as 3 pct, and permeabilities decreased up to three orders of magnitude. Slaky coal waste material had physical property reactions to the addition of fines substantially different from those of nonslaky material.

Jan 1, 1981

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of the Ohio coalfield. Washability analyses were made on 39 coalbed samples collected from a 14-county area. None of the samples were of metallurgical quality as received. Nine of the samples could be sufficiently upgraded to produce metallurgical-grade products, and the remaining 30 samples could not be upgraded to this quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, 10 of the samples were of medium sulfur content as received and one could be upgraded to a low sulfur content. Of the 29 samples having a high sulfur content as received, 18 could be upgraded to a medium sulfur content. The original sulfur content of the other 11 samples having a high sulfur content as received can be appreciably reduced by removal of the sink 1.58 specific gravity material; however, these coals would be classified as high sulfur coals both before and after removal of the sink 1.58 specific gravity material.

Jan 1, 1972

By J. C. White

A research study was conducted to devise a method for producing phosphoric acid directly from unbeneficiated Florida phosphate matrix. This research was performed as part of the Bureau of Mines, U.S. Department of the Interior, goals of improving minerals and metals recovery from domestic resources and of minimizing the environmental impact associated with mineral recovery operations. This report describes research in which unbeneficiated, dry, south-central Florida phosphate matrix was digested with sulfuric acid in a continuous-circuit, five-tank reactor to yield phosphoric acid and gypsum residue. Feed capacity of the reactor was 100 pounds (45 kg) of dry matrix per 24-hour day. When digestion was carried out at 185° F (85° C), acid filtration rates of up to 420 pounds of P20S per square foot per day were attained. Combined iron and aluminum impurities in the product filter acid were about 60 percent greater than values reported in commercially produced acid derived from concentrate. phosphate recovery was 87 to 90 percent of the phosphate contained in the as-mined matrix.

Jan 1, 1978

By D. L. Boreck

Thick coal seams are common in the Western United States, Many seams are over 50 it thick (some are over 200 ft thick) and are too deep to extract using surface methods. Currently, such deposits are developed using standard "eastern" mining methods which only extract a few feet of total seam thickness, often rendering the remaining coal unminable with current technology. Novel methods that increase thick-seam recovery have been developed and are currently being used in Europe. These methods--high-face single-pass and multislice longwall, longwall caving, and hydraulic mining--have great potential for use in the United States. Successful use of these methods is an objective of the Bureau of Mines. Their use requires, among other things, a full evaluation of geologic features common to thick coals. The objective of this report is to present and summarize those features that will affect the introduction of the methods into thick-seam mines in the Western United States. The geologic elements delineated are three-dimensional configuration of the seam, cleat development, joints and fractures, roof and floor lithology, and faulting.

Jan 1, 1986