Search Documents

By Charles E. Whieldon

This report presents the results of a study on part of the Smithfield oilfield, Wetzel County, W. Va. The primary purpose of the investigation was to determine the original and the present volume of stock-tank oil in the formations and to investigate the feasibility of waterflooding the Gordon Stray, Gordon, and Fourth sands underlying the I. D. Morgan lease. The study was based on laboratory core analyses, geophysical well logs, geologic considerations, and various field prediction data from the I. D. Morgan lease. The Bureau found that, of the three sands cored, the Gordon Sand was the best prospect for waterflooding, and that a properly engineered water flood should recover 136 to 230 barrels of oil per acre-foot from this formation.

Jan 1, 1967

By A. Visnapuu

The Bureau of Mines investigated carbonyl processing techniques for the recovery of the critical metals Ni, Co, Mn, and Cr from domestic primary and secondary sources. In most cases, the source materials require reductive precarbonylation treatment to metallize the contained Fe, Ni, and Co compounds to render them reactive with CO. The critical metals were recovered either by direct conversion to the respective carbonyls or as upgraded products by carbonyl removal of an undesirable metal. Best metal-to-metal carbonyl conversion was under CO pressure, from 80 atm upward, and at 1400 C. Carbonylation was accelerated by the addition of HzS in small quantities. CO pressure, temperature, promoter and pretreatment trends, and other factors enhancing metal carbonyl formation are presented.

Jan 1, 1987

By G. E. Rennick, F. E. Armstrong, J. Pasini, J. R. Abrams

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 112 part per billion. Expand- able cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jul 1, 1972

By W. N. Marchant

The Bureau of Mines improved removal of selenium from zinc smelter acidic gas scrubber effluent by using zinc dust to precipitate soluble selenium prior to lime neutralization. Lime neutralization alone decreased selenium in the waste water from, typically, 6 parts per million to 2 parts per million, whereas the use of zinc dust precipitant gave an effluent containing less than 0.1 part per million of selenium. The waste treatment operation first was developed on a laboratory scale and later was successfully tested at a smelter site on a 1-gallon-per-minute basis. During the research a simple and rapid means was developed for determining selenium in waste water; the technique enabled visual semiquantitative selenium determinations that later were confirmed quantitatively by X-ray fluorescence.

Jan 1, 1978

By Sidney Katell

This report is an economic evaluation of the production of hydrogen in a continuous system by the steam oxidation of partially reduced iron oxide in a fluidized bed at 7 atmospheres using producer gas to reduce the iron oxide. The oxidation-reduction step is based on experimental data obtained by the Bureau of Mines at the Pittsburgh Coal Research Center. The estimated capital requirement for a plant producing 30 million std. c.f.d.3 of 99.8 percent purity hydrogen at a discharge pressure of 450 p.s.i.g. is $13,100,000, using January 1961 equipment cost data. Based on a 330-day operating year, the operating cost before profit and taxes with coal price as a variable is estimated to be:

Jan 1, 1962

By B. J. Scheiner

As part of its mission to reduce pollution associated with mineral production, the Bureau of Mines is developing a dewatering technique for phosphatic clay waste that uses a flocculant, polyethylene oxide (PEO). This flocculant forms strong, stable flocs, which can be partially dewatered on a static screen and dewatered further on a rotary screen. Using this technique, a field test unit (FTU) was operated at a nominal 100 gal/min. Consolidated phosphatic clay material containing 20 percent solids was produced when feed slurries of 3 percent solids were treated with 0.69 pound of PEO per ton of feed solids. Pit and column tests indicated that the PEO-treated material continued to dewater; compacted products containing 40 percent solids were obtained after 45 days.

Jan 1, 1981

By Charles Prasky

This report describes bench-scale studies and pilot-plant development of the Bureau of Mines process for roasting iron ores with a ferrous scrap reductant, such as discarded automobile hulks, to yield artificial magnetite. Quality magnetic concentrates containing about 66 percent iron and 6 percent silica with iron recoveries of over 90 percent were obtained after roasting fine-grained oxidized or nonmagnetic taconite with unburned, sheared automobile hulks in a rotary kiln. The relatively complete oxidation of the lighter gage metal in the automobile during roasting resulted in a metallic byproduct consisting of the unconsumed heavier gage metal scrap. This residual or tailored scrap is potentially useful as heavy melting stock and has more value than the original automobile hulk.

Jan 1, 1970

By Walter E. Pittman

This Bureau of Mines study surveys the current state of technology and the various research efforts that have been undertaken to dewater the dilute phosphatic clays generated in the production of phosphate rock. The research described includes early dewatering experiments, fundamental studies of clays and of flocculation, and minor dewatering techniques such as freeze-thaw methods, the ANDCO process, moving screens, sand wick, crust development, and overburden pumping. Some methods that are currently being evaluated are described. They include the Estech sand-clay mix process using the Enviro-Clear thickener, sand-clay sandwiching, dredge mix, dredge process, and the sand-spray process. Developing technology for dewatering phosphatic clays also is described, including the Bureau of Mines rotary trommel method and the Gardinier process.

Jan 1, 1984

By R. O. Pynnonen

Tunnel-driving is recognized as a hazardous occupation; adequate support of roof and sides for preventing accidents from falling material is usually one of the most important safety problems. Where extraordinary conditions of sand and water are found, this problem becomes even more difficult. Tunneling at the Tioga No.2 mine was stopped when a 22-foot bed of water-saturated, fine gray sand was encountered. The tunnel, designed to house an ore-conveyor belt, was being driven from both ends. Driving was extremely difficult at both the upper and lower faces when the sand horizon was reached. A distance of 178 feet remained between the faces. Heavy pressures deformed the steel-supporting rings at the upper face, and there was an inrush of mud and sand at the lower face.

Jan 1, 1958

By Thomas E. Marshall, Patrick A. Kinek, Gerald L. Finfinger

The purpose of this investigation was to evaluate the integrity of the existing shutoff valves and actuators used under high-temperature conditions in the Bureau of Mines' horizontal borehole methane drainage pipe- line system and to determine the potential for improvement in the system. In the field tests, both fire-safe ball valves and standard brass ball valves were initially subjected to a 30-min pan fire without thermal protection. Neither valve could maintain line pressure beyond 11 min in a fire that reached temperatures between 500° and 700° C. Based on the test results, it was concluded that the brass ball valve used in the Bureau's methane drainage pipeline system can be retrofitted with an inexpensive "fire bag" to substantially increase its integrity under mine fire conditions.

Jan 1, 1986

By Eric E. Cather

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 5,100 acre (2,065 ha) Rubicon RARE II area (No. 5026) in the El Dorado National Forest (fig. 1). Work by the Bureau of Mines indicates that potential for mineral resources in the area is low. Samples from small gravel deposits along the Rubicon River and from favorable structures in the area contained smart amounts of economic minerals. A Tertiary river channel near the north area boundary contains gold values as much as $137.60 per cu yd ($180 per cu m) [(gold at $400 per troy oz ($12.86 per g)]. The channel does not cross the study area. Energy resource potential, including oil, gas, or geothermal, does not exist in this geologic environment.

Jan 1, 1982

By Lambert Dolphin, George Oetzel, Robert Bollen

An electromagnetic sounder developed for an archaeological application in Egypt has been successfully tested in a California dolomite mine. Chambers in the mine 100 to 130 feet from the surface gave intense, well-defined echoes consistent with an average attenuation coefficient of 0.6dB/m and a relative dielectric constant of 11. By moving the transmitter and receiver units on the hillside above the underground chambers, various characteristics of the propagation could be observed such as dispersion, chamber aspect sensitivity and cross section. The transmitted pulse was one to one-and-a-half radio-frequency cycles long at a peak power of 0.2 MW. Frequencies employed were 16 to 50 MHz. The light weight, highly portable, battery-powered equipment is potentially suited to other underground sounding applications.

Jan 1, 1973

By Fred Turin, Kim Cornelius, Lisa Steiner

NIOSH researchers have been examining underground coal mining activities in order to evaluate work crew hazards. In 1994 a continuous mining machine operator was killed by falling roof during extended cut mining. Many aspects of the incident were used by NIOSH researchers to develop a scenario interview. The goal was to provide a realistic framework for acquiring frank and detailed insights. The interview consists of two sections. The first describes the underground mining conditions. The second recounts the fatal incident. Each section is supplemented by a diagram and a set of questions addressing relevant safety issues. The interview was administered at three mines that actively take extended cuts. Researchers found the scenario approach to be an effective interview tool as well as an effective hazard awareness and safe work practices training platform.

By Nicholas T. Zilka

One mineral deposit in the Golden Trout Wilderness has potential. The currently producing Pine Tree Mine on the Little Kern River has an estimated 120,000 tons (109,000 t) each of indicated and inferred reserves averaging 0.77 percent tungsten trioxide. No apparent potential exists for base or precious metal or other mineral deposits. INTRODUCTION The Golden Trout Wilderness, established by Congress in 1978 under Public Law 95-237, encompasses 240,000 acres (97,000 ha) of conifer-forested, rolling, upland plateau at the headwaters of the Kern River in Inyo and Sequoia National Forests (fig. 1). Abundant streams locally contain Golden Trout, namesake of the area. Major roads serve the area to the west and east of the Wilderness; access is poor to the north and south.

Jan 1, 1982

By C. A. Komar

Hardness, tensile strength, and impact toughness of dry and brine-saturated sandstone specimens were measured at ambient, cryogenic, and elevated temperatures as a measure of the relative stability of reservoir rocks for subsurface disposal of liquid wastes. Hardness measurements were inconclusive. Tensile strength and impact toughness were significantly higher at -320° F than at ambient temperature, but were relatively unaffected at 700° F. Impact toughness was reduced by subjecting the specimens to three cycles of rapid temperature changes (thermal shock) over a 1,000° F range. Tensile strength of brine-saturated sandstone was less than that of dry sandstone. Based on results of the tests, reservoir sandstone likely would be stable if exposed to extreme temperatures of liquid wastes, although rapid changes in waste temperatures should be avoided.

Jan 1, 1971

By John C. Edwards

The Bureau of Mines developed a mathematical model to calculate the aerodynamically induced lifting of coal and rock dust from a composite deposition on a mine entry floor and the subsequent transport of the dust ahead of the propagating combustion zone of a coal dust explosion. For a series of experimental explosibility tests approximated by combustion zones that expand at a constant flame velocity, the mass fraction of airborne rock dust ahead of the flame front, as well as the mass fraction overtaken by the combustion zone, was calculated. A statistical analysis of the theoretical results demonstrated with a high level of confidence that the propagating and nonpropagating test samples belonged to sepa-rate populations. This analysis was further supported by an independent model of the average temperature over the combustion zone.

Jan 1, 1988

By Roy T. Sorensen

This Bureau of Mines report presents the results of a study to rank technologies for extraction of alumina from bottom ash and coal shale. The available literature on composition and availability of coal waste was reviewed, and papers pertinent to alumina extraction are referenced. Types of coal waste were categorized by method of waste generation, coal content (heating value), location, coal type (ash nomenclature), and alkaline earth content. The differences and similarities among the categories of coal waste are summarized as to factors that my affect aluminum extraction, especially factors concerning chemical composition, current production, storage problems, and accumulated tonnage. Data available on physical characteristics and mineralogy did not correlate well with the individual categories of coal waste, and discussion on these two aspects is limited to the differences between coal ash and coal shale.

Jan 1, 1983

By D. H. Chambers

The Bureau of Mines developed a process for producing high-purity zinc and tin by electrorefining from liquid amalgams. Commercial grade metals were dissolved in mercury to produce saturated amalgams at room temperature. Amalgams were also prepared by electrolytic transfer from soluble anodes of the metals to a mercury cathode. Amalgams formed by both methods were used as anodes in electrorefining cells to produce high-purity cathodes. Metal impurities, excluding mercury, were at levels of less than 5 ppm in zinc and 9 ppm in tin. Mercury content was about 2 to 10 ppm in zinc products, and this was effectively removed by heating the cathodes in a vacuum. Mercury was excluded from tin cathodes by pumping the tin electrolyte through tin turnings and controlling the cell temperature.

Jan 1, 1969

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots."

Dec 1, 1942

By A. E. Raddatz

The Bureau of Mines has determined the electrochemical rate of anodic dissolution of vanadium metal in a VC12-VC13-NaC1 electrolyte at 860' C for the purpose of elucidating the reaction mechanism. Rate measurements were carried out with the help of specially designed equipment capable of continuously recording the weight loss experienced by a cylindrical vanadium anode immersed in the molten salt electrolyte while a constant current is maintained through it. The rate is expressed as a function of current density and VC13 concentration, and the reaction is interpreted in terms of an adsorption mechanism. Multiple regression analysis of the data gave the following rate equation: Rate x 104 (g.cm-2.sec-1) = -0.38 + 2.64 current density (amp-cm-2) + 0.69 log, (mole-percent VC13).

Jan 1, 1974