Search Documents

By H. A. Tucker

This Bureau of Mines investigation was conducted to determine the appropriate quantities of rare-earth methals (REM) in the form of silicides to add to an alloy steel for the purpose of increasing toughness and ductility. The work was conducted in a vacuum induction furnace with the rare-earth additions required to deoxidize and desulfurize a simulated basic oxygen furnace (BOF) vacuum-degassed steel initially containing 0.013 to 0.016 percent sulfur. The product proved to be as good or better than the best basic electric furnace steel of the same composition made by the steel industry. Twenty-three experimental heats of 5 Ni-Cr-Mo-V steel were made, cast into 50-1b ingots, and hot-worked in a press and a rolling mill to ½ inch plates which were then heat-treated to 130/150 ksi4 yield strength. Impact and tension tests showed that the addition of 0.025 to 0.100 percent, or ½ to 2 lb per ton, respectively, of rare-earth metals when compounded with silicon were appropriate for increasing toughness and ductility. These quantities resulted in retained cerium contents between 0.014 to 0.025 percent, and increased the Charpy V-notch energy absorption and the percent reduction of area significantly as compared with base heats at the same sulfur content levels. All the test heats, including those with additions of REH of as much as 4 lb/ton, had greater Charpy V-notch energy absorption values than the base composition could have developed at the starting sulfur range of 0.013-0.016 wt pct.

Jan 1, 1968

By Robert E. Johnson

THE MILDEST recession of the postwar period ended in the first months of 1961, and the economy climbed steadily during the remainder of the year. The Federal Reserve Board (FRB) Index of Industrial Production climbed from a low point of 102 (1957=100) in February to 115 in December, a rise of 12.5 percent. But economic activity for the year as a whole was only 1.5 percent higher than the 1960 level, as measured by real gross national product (GNP). Although activity increased throughout 1961, much of it was merely regaining ground lost in the decline during the second half of 1960 and the first months of 1961. The FRB index did not re ain the July 1960 high of 110 until June of 1961. Mineral fuels did not fully share in the economic recovery. The (FRB) crude oil and natural gas index rose only 5 percent between February and December. Although the index of monthly coal production increased 11.5 percent during the year, the February level was so low that total production for the year was the lowest since 1954. Total production of energy measured in Btu's was up slightly (1 percent) during the ear. Coal production was down; production of crude oil and natural gas was up. Calculated consumption paralleled production-total up slightly, coal lower, and crude oil and natural gas higher. The most interesting product developments were in coke and residual fuel oil. Sales of coke showed a sharper drop than steel

Jan 1, 1962

By Warren E. Morrison

The continuing high-level performance of the domestic mineral and mineral fuels industries during 1966 was sustained by the longest business upturn in the Nation's history. Spurred by consumer demand at home and the defense production requirements of the Viet-Nam war, the rising trend of economic activity during the year was reflected in the upward movements of the major economic indicators. At yearend the gross national product (GNP), representing the value of all goods and services produced, stood at $740 billion, $58 billion greater than in 1965. Corrected for price changes, the real value of GNP in terms of 1958 dollars was $648 billion and represented an annual increase in economic activity of 5.4 percent. Some 74 million persons were employed during the year out of a total population of 196.8 million, while unemployment fell below 4 percent. The Federal Reserve Index of Industrial Production averaged 156 for 1966, up 13 points from the previous year. However a jarring note in the 1966 expansion, and one which affected the mineral industries in particular, was the increasing pressure on prices and the threat of inflation. From 1961-65 economic growth was facilitated by relatively stable wages and prices and only mild inflation. During the period average wholesale prices hardly moved while average consumer prices rose only about I percent per year. But this long run of relative price stability ended during 1966 when consumer prices rose 2.9 percent and wholesale prices were up 3.2 percent from the previous year.

Jan 1, 1967

By Joseph A. DeCarlo

This publication presents a tabulation of oven-and beehive-coke plants in the United States as well as pertinent statistical data on the number, capacity, kind, and condition of the ovens. Coke is an essential raw material in pig-iron production and the coal-chemical materials produced during the coking process are used to manufacture fertilizers, paints, plastics, synthetic rubber, explosives, detergents, nylon, pharmaceuticals; dyes, and many other products necessary to the high standard of living in this country. In table 1 the oven-coke plants in the United States on December 31, 1959, are listed. This shows the name and address of the company, location of the plant, classification or type of ownership, number and type of ovens, annual coke capacity, and the coal-chemical materials produced. The "furnace" plants I are those owned by iron and steel companies and most of them are integrated with blast furnaces to facilitate transportation of raw materials for steel making. Furnace plants represented 87 percent of the total coking capacity and their average annual capacity was 1. 3 million tons. The "merchant" plants are those associated with chemical companies, gas utilities, as well as those that produce metallurgical, industrial, and residential-heating grades of coke and coal-chemical materials for sale on the open market. These coke plants are smaller than furnace plants and in 1959 their average coke capacity was only 520 thousand tons annually. On December 3l, 1959, there were 54 furnace and 20 merchant oven-coke plants in existence in the United States.

Jan 1, 1960

By R. Blickensderfer

Test equipment that simulated frictional impacts between coal-cutter bits and mineral inclusions at a coal face during operation of a continuous coal mining machine was used by the Bureau of Mines in the laboratory to study the incendivity of impacts between various rocks, metals, and hard-metal alloys in an explosive mixture of air-7 pct natural gas. Quartzitic sandstone was found to be the most incendive of several rocks tested. Limestone concretions from a coal seam, known locally as "sulfur balls," sparked furiously but were not incendive. Among the metals tested, the type of steel used in commercial coal-cutter tools was the most incendive material tested. A l7-4PH stainless steel was less incendive and appears to be the most promising high-strength steel alloy, reasonably economical, for use in coal-cutter bits. Some hard-metal alloys, primarily titanium and zirconium diboride composites, were also evaluated as possible replacements for the conventional cobalt-bonded tungsten carbide used in the tip of coal-cutter bits. The metal-bonded diborides were generally less inc endive but more brittle than the conventional tungsten carbide. Carbonitride coatings on tool bits were also tested but found to have no advantage. The source of ignition during frictional impact between metal and rock was studied. Immediately after impact, a yellow flash was observed and a smear of metal near its melting point occurred on the rock. This hotspot on the rock, rather than the yellow flash or sparks or metal fragments, was observed to be the cause of the ignition.

Jan 1, 1974

By W. R. Huff

Yield stress and plastic viscosity values, determined from shear rate-shear stress relationships, were found to be a linear function of coal concentration for coal-water slurries containing 40, 45, 50, and 55 weight-percent of powdered coal. In the laminar region, the flow is described by an equation derived from the fact that the square root of the shear stress varied linearily with the square root of the shear rate. In the turbulent region, the friction factor was found to be inversely proportional to the velocity to the 0.12 power.

Jan 1, 1965

By Thomas Varley

Data on the consumption of reagents used in .flotation during the year 1925, in metallurgical plants in the United States, are presented in this paper. Previous reports have covered the same subject for the years 1916, 1919, 1923 and 1924. The data contained herein show departures most radical from even the 1924 practice. Flotation has developed rapidly and on a more scientific basis than ever before. Perhaps more fundamental and useful data have been uncovered during the past two years than in all the years the art has been practiced.

Jan 1, 1926

By Guy A. Johnson

This Bureau of Mines report summarizes the results of efforts to develop reasonably priced, reliable mine shaft fire and smoke protection hardware for metal and nonmetal mines. The hardware was incorporated into a viable prototype system that would minimize fire and smoke hazards. The design of the system had to be sufficiently flexible to be utilized in a wide variety of metal and nonmetal mine shaft and shaft station configurations. As a result of long-term, rugged field tests, an improved (second generation) system was developed. The hardware is now commercially available.

Jan 1, 1978

By G. S. Rice

The recommendations of the Bureau of Mines on rock-dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions,5 approved by the. American Engineering Standards Committee,6 December 30, 1925 It is specified that the dust to be used is of a size that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch.

Jan 1, 1930

By F. A. Rutledge

The Rainy Creek deposits lie at the western base of the Kilbuck Mountains, about So miles southeast of Bethel, in southwestern Alaska. The deposits were brought to the attention of the Bureau of Mines by placer miners on Rainy Creek after cinnabar concentrates were recovered by their gold-mining operations. In August 1947 the Bureau excavated 1,500 feet of dozer trenches totaling 2,547 cubic yards. Further hand trenching in the bottoms of the dozer trenches on the surface totaled 1,440 linear feet, or 40 cubic yards. Nineteen samples were taken for analyses.

Jan 1, 1948

By G. W. Jones

Phthalic anhydride is a solid having the formula C8H4O3. It is an important intermediary in production of anthraquinene, alkyd reins, and plasticizers. The combined annual production of phthalic anhydride reported by 10 major manufacturers for 112,250 tons. The raw materials in the manufacture of phthalic anhydride have been the source of numerous fires and explosions. Consequently, the need was felt to determine the temperature flammability and the ignition temperatures crude basic raw material in most phthalic anhydride production crude phthalic anhydride, and pure phthalic anhydride.

Jan 1, 1950

By John R. Benham

The Blue Joint Mtn. RARE II area may contain barite resources. One claim, the Woods Creek Barite No. 1, contains two veins of barite of drilling mud quality. The quantity of barite present could not be determined due to limited surface exposures. Sections 1, 2, 11 and 12 of T. 2 S., R. 23 W. in the study area are classified by the U.S. Geological Survey as prospectively valuable for geothermal energy resources. These sections border Blue Joint Creek Hot Springs, which are outside the study area.

Jan 1, 1981

By E. H. Denny

A most interesting safety record has been made by the Colorado Fuel and Iron Co. s. Robinson ho. 1 mine located at Walsen, Cola. Mr. J. L. McBrayer has been superintendent of the Robinson No. 1 and 2 mines for the past 2 1/2 years, and Mr. David Muir has been foreman of the Robinson No. 1 mine since June, 1913. The last fatal accident at Robinson No. 1 mine occurred on July 27, 1915, and the tonnage produced at this mine since July 28, 1915, has been as follows:.

Jan 1, 1929

By W. H. Pailes, V. Castranova, D. Lewis, G. Goodman

We performed bronchoscopy with bronchoalveolar lavage (BAL) in 8 control subjects with no exposure to occupational dusts, 8 healthy power plant workers exposed to mixed dusts (primarily fly ash), 1 healthy coal miner and 1 rock driller with acute silicosis. All subjects were non-smoking males. We analyzed lavage effluents for total numbers of alveolar macrophages, lymphocytes and neutrophils and monitored chemiluminescence at rest (REST CL) and after stimulation with 3x10- M phorbol-12-myristate-13-acetate (PMA CL) or 2 mg/ml zymosan (ZYM CL). The data are as follows:

Jan 1, 1988

By Hans M. Cassel

The specific objective of research presented in this report was clarifi- cation of physicochemical fundamentals of the mechanism of dust explosions. The equipment, techniques (chiefly photographic), and dusts (chiefly graphite and light metals) employed are described. From behavior of individual par- ticles, conclusions are drawn as to their cooperative function in ignition and combustion of dust clouds. Results are interpreted using thermal theory as accepted for combustible gas mixtures. Radiative transfer across the flame front, as a characteristic of dust flames, is given particular atten- tion. Related studies by other investigators are discussed.

Jan 1, 1964

By I. AITKENS

Tourmalines are among the most beautiful of all the semiprecious stones, and are unsurpassed even by corundum in variety of hue. The stones most suited to jewelry purposes are those comparatively free from iron. One reason for the fact that the tourmaline has advanced rapidly in public favor in this country is that it is found in California in great profusion and of extraordinary quality. The superb green and especially the pink crystals found at Pala and Mesa Grande in San Diego County, Calif., are deemed superior to tourmalines from all other localities.

Nov 1, 1931

By Fred N. Kissell

The U.S. Bureau of Mines was established in1910 to reduce .the high accident rate in the nation's coalmines. For 85 years, it conducted a wide variety of tasks related to mining before it was abolished in 1995. The BOM had many technology transfer successes in its lifetime, including more than a dozen "R&D100" awards. This essay identifies and discusses five "transfer factors" that can explain the success (or failure) of many Bureau of Mines projects. These five factors are termed "pressure, pitfalls, path, price, and profit."

By John N. Murphy

In fiscal 1996, the US Congress directed that the US Bureau of Mines (USBM) be closed. Certain functions were reassigned to other agencies. The remaining employees were separated and the unoccupied sites were decommissioned. As a result, 12 locations were closed and about 1,200 employees were terminated in March 1996. About 600 employees at five locations were reassigned to other federal agencies. This article provides a summary of the continuing functions, the agencies involved and the points of contact for each continuing function. The functions that were discontinued are also identified.

By R. V. Ramani, V. T. Burgos, J. A. McClay

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herlckes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to September, 1974. Thls report was submitted by the authors on February 13, 1975.

Jan 1, 1975

Mine closing methods should be carefully considered. If not properly sealed, an abandoned mine may continue to produce acid water. Since 60 to 90 percent of the total acid discharged from all coal mines is from abandoned mines,(58) some states require that provisions for sealing be contained in the mining permit application. Closing an operation to prevent harmful mine drainage into nearby runs and streams is a subject of much concern to states as a result of continuing problems from long abandoned mines which were improperly closed.

Jan 1, 1970