Search Documents

This report describes magnetic field measurements in the Helvetia Coal Co. Lucene #8 Mine for purposes of deriving a mapping of the magnetic field strength covering the major haulageways which contain conductors. The measurements were performed by Terry S. Cory, P.E. under U.S. Bureau of Mines purchase order P0372716. Assisting in performance of the measurements were personnel from the Bureau of Mines, PMSRC, and Helvetia Coal Co. Acknowledgement is given to Engineer Tom Strong of Helvetia Coal Co. who accompanied the measurement team and who lended support in performing the measurements and in supplying valuable engineering information for use in evaluation of the results. The results of the testing at medium frequency show that coverage of the entire mine area containing conductors can be achieved employing wireless radio techniques whereby radio signals are coupled into and are carried by these conductors. These results confirm earlier qualitative testing of the Collins Mine Wireless Radios in this mine. These results, performed over the frequency range 71-2890 KHz, illustrate the effect of frequency on the radio propagation with the conclusion that the best overall coverage is obtained at frequencies approximating 1000 KHz. This report presents all the raw data and the reduced data in the form of magnetic field strength contour maps. Sufficient information is provided to enable independent reduction of the data. A summary of observations which can be made directly from the contour maps is given.

Jan 9, 1977

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX A - PNEUMATIC TRANSPORT OF FLY ASH 1. Introduction Two types of pneumatic transport of fly ash are critical to the success of (1) Transport of fly ash from the fly ash truck to the entrance to the borehole. Depending on the surface topography, this may be horizontal, decential and ascential. (2) Vertical downflow of fly ash through the borehole. All fly ash trucks have limited pressure with which they can pump the fly ash. Thus, the pressure drop in the fly ash hose will define the maximum length for pumping and consequently the maximum distance that the fly ash truck can be parked from the auxiliary blower. The same relationships describe the flow of the dilute fly ash-air mixture produced by mixing with the auxiliary air from the blower and thus define the selection of the pipe diameter. These are im¬portant considerations in the proper selection of the location of the passages to be sealed and the type of surface preparation required. The flow characteristics of fly ash down the borehole determine the selection of the minimum borehole diameter and the blower pressure. This appendix presents theoretical analyses of these flow regimes and summarizes the limited experimental data obtained during the field tests at Grant Town, described in Section 8.4. The analysis for the borehole flow is presented first as it is of greater interest to the program. This is followed by a discussion of the horizontal flow.

Jan 1, 1973

By Frank J. Susko

The U.S. Bureau of Mines is developing a process for removing metals from mining and mineral processing waste streams by precipitation. The precipitation process is accelerated by flocculation when a high molecular weight polymer is added. Infrared (IR) studies were performed on zinc hydroxide [Zn(OH);J, copper hydroxide [Cu(OH);J, and zinc sulfide (ZnS) flocculated with both non ionic and anionic polyacrylamide (PAM) and polyethylene oxide (PEO). The IR data were compared with general trends in the performance of the polymers observed during flocculation. These studies will help to understand the bonding between the precipitate and polymer and indicate the effectiveness of a flocculant for dewatering. Two types of bands showed up on the IR spectra; one type described the interlayer water of the flocs, the other described the organic bonds of the polymers. A general decrease in the areas of the three water bands, hydroxyl (O-H) stretching (3,200-3,500 cm-1), water bending (1,610-1,630 cm-1), and torsional oscillations (600-700 cm-1), indicate interlayer water being driven off, which is a favorable condition in flocculation. Shifts in the O-H stretching band indicate water bridging between the precipitate and polymer. Shifts in the amine (N-H) deformation, carbon-nitrogen (C-N) stretch band (1,600-1,610 cm-1) indicate the amine group of the PAM is involved in the bonding. Evidence suggests that ether oxygen of PEO is also involved in the bonding process.

Jan 1, 1990

By D. Litton, H. Dobroski, J. G. Kovac

Since 1910, the U.S. Bureau of Mines (USBM) has investigated practical ways of dealing with the consequences of major fires and explosions in underground mines. The results of this research have had a significant positive impact on the mining community by enhancing mine workers’ chances of surviving an underground mine disaster. Today, the Bureau continues to conduct research in mine disaster mitigation. Much of this work has direct application to search and rescue situations, such as: emergency evacuation through smoke-filled or otherwise unbreathable atmospheres, locating and rescuing survivors from rubble piles, and fire fighting in confined spaces. Three USBM research areas are discussed: (1) Life Support -- This effort is directed toward research into and development of closed-circuit breathing apparatus for use in hazardous environments which are likely to be encountered in the aftermath of a mine disaster. (2) Trapped Miner Location -- A mine disaster may result in the entrapment of miners whose normal escape routes are cut-off. This research activity resulted in the development of transportable seismic technology that can be used to locate trapped miners. (3) Mine Fire Diagnostics -- This research involves developing practical techniques for remotely monitoring how the atmosphere inside a mine changes during a fire, in order to estimate the spread and severity of an underground fire. This information is critical in deciding how best to fight a mine fire, or whether it is safe to mount a rescue and recovery mission.

By Jennifer A. Slatnick

The U.S. Bureau of Mines estimated the potential availability of titanium from 39 mines and deposits in 12 market economy countries. The evaluated properties account for 76 pet of the market economy country demonstrated resources, which total 603 Mt of contained titanium dioxide (Ti02) in the minerals rutile, ilmenite, leucoxene, and anatase, and represent 95 pct of current production. Approximately 250 Mt of contained Ti02 could be economically recovered from evaluated titanium operations at January 1992 market prices. In terms of mineral concentrates, this equals approximately 19 Mt of rutile concentrate, 110 Mt of ilmenite concentrate, 47 Mt of synthetic rutile concentrate (in addition to the ilmenite), and 160 Mt of titanium slag that could be recovered. Over the past decade, the titanium minerals industry has adapted to the changing market. In the 1980's, titanium producers expanded production because of the rising demand for titanium products. Today, the titanium industry is in a state of overcapacity, and byproduct revenues, such as that from zircon, have become essential in keeping operations profitable. The industry has also witnessed a greater dependence on upgraded ilmenite products, such as titanium slag and synthetic rutile, because of the expense of rutile and the lower wastes emitted from these upgraded products. As a result of this dependence on upgraded ilmenite products, South Africa has become a leading titanium producing country and has displaced Australian production.

Jan 1, 1994

By J. H. Schuenemeyer

Consider a set of points, some of which are anomalous (larger than a specified cutoff value), located on a plane. Whether some or all of these points are clustered to form one anomaly or more or, alternatively whether these points are scattered at random, may be investigated by measuring perimeters of convex hulls. A convex hull is the smallest convex polygon that will encompass a group of points. (Examples of convex polygons are triangles, rectangles, and all other regular polygons.) A set of anomalous points is selected and the perimeters of the convex hulls of this set and all its subsets are measured and compared with tabulated values of perimeters for each subset size. For a given subset size consider those perimeters which are less than the tabulated perimeter. If the number of convex hulls is greater than the maximum number expected by chance, then the chance that any one of the observed-hulls-is a nonrandom cluster is the ratio of the observed number to the sum of the observed and the maximum number expected by chance. Otherwise, the points are evidently not clustered. If many sample points are anomalous, an alternate model defines various configurations of contiguous points and compares the observed number of configurations per unit area with the expected number. Applications are discussed in several fields of geology and geochemistry-including geochemical exploration surveys and heavy mineral spatial distributions--as well as in mining (dust control) and medical geography.

Jan 1, 1972

By David C. Oyler, William P. Diamond

Three long horizontal holes were drilled from a directionally drilled sur¬face hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diam¬eter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a verti¬cal depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 m (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By Isaac A. Zlochower

A number of ignition incidents involving mining and farm equipment have illustrated the surprising danger of drilling, cutting, or otherwise penetrating sealed compartments or frames that are filled with metal scrap for ballast. The presence of chemically-reactive metals (or electrochemically-active pairs), such as zinc in galvanized steel, can produce hydrogen from moisture in the steel scrap, and the resulting pressure, due to the internally-generated hydrogen, can produce an easily-ignited gas jet when the sealed component is penetrated.

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 44,015 employees worked in underground mining locations in 2003, corresponding to 44,778 full-time equivalent (FTE) workers. • Ninety percent of underground employees (n = 39,735) were mine operator employees. • Contractors comprised 10% of all underground mining employees (n = 4,280) and comprised only 5.8% of all underground FTEs. • The majority of underground employees worked for coal operators (73.0%; n = 32,130).

Feb 1, 2005

By E. J. Kloos

Two self-contained breathing apparatus of the closed-circuit compressed-oxygen type were evaluated for performance at 32° to -25° F. Low-temperature effects of oxygen and carbon dioxide concentration, visual properties of the facepiece, and mechanical operation of the apparatus were studied. Although operation varied with the wearer, his breathing rate, the apparatus precooling time, and the temperature, results suggest that general use of currently approved compressed-oxygen closed-circuit breathing apparatus be limited to temperatures above 32° F.

Jan 1, 1968

By John C. Holtz

The Bureau of Mines studied air contamination caused by diesel exhaust in a 10,000-ft ventilated tunnel. Sequential air samples were taken at the ends and middle of the tunnel during an operating cycle. Observed and calculated results for carbon dioxide, carbon monoxide, and nitrogen oxides were essentially in agreement. Nitrogen dioxide was present only in trace amounts. It was found that contamination was related to the volume of ventilating air, the number of haulage trips, train speed, and engine load.

Jan 1, 1968

By H. E. Blake

An evaluation was made to determine the economics of utilizing waste fluosilicic acid for production of (1) calcium fluoride, and (2) anhydrous hydro-gen fluoride. Two versions of each process were considered and compared. The evaluation showed that both products could be produced and marketed competitively. Lowest estimated product sales prices required to yield a 25-percent return on investment before taxes (discounted cash flow basis) was $339.34 per ton of hydrogen fluoride and $48.64 per ton of calcium fluoride.

Jan 1, 1971

1. Alford, N.G. quantity, of timber used in soft-coal mines and how much will be needed for the future. Gives a table of estimated increase in mine timber consumption in the future. A.I.M.E. Separate. 1336-C 1924. 2 Clark, B.M. The forest and the mine. Rept. Conference of Wood-Using Industries, Harrisburg, Pennsylvania. Apr. 13-14, 1921, pp. 58-62. Describes experience of a Pennsylvania mining company in depletion of timber supply and conservation methods adopted.

Jan 1, 1925

By George McCaa, H. C. Howarth

"During recovery operations following a recent coal-mine explosion, 12 small fires were encountered near the break line of pillar extraction in a large panel. All of the fires except one were quickly extinguished by the rescue and recovery parties. This fire had found its way into a large quantity of loose material at a corner of the cut-through between two rooms, about 100 to 150 feet from the break line of an extensive goaf; had it been necessary to seal the fire, the inclusion of this break line not only would have made the work difficult but would have made the section hazardous as it probably would have given off gas. The fire covered a floor space of about 100 square feet and when discovered was burning briskly, with the flame extending to the roof at a height of 3 or 4 feet; it was the cause of much apprehension on the part of those in charge of the recovery operations and resulted in delaying the work considerablyThe object of this article is to describe in detail the method by which the fire was brought under control and finally extinguished, so that other persons encountering similar conditions may have the benefit of the experience.When the fire was discovered a request for rock-dust, fire extinguishers, and other fire fighting equipment was telephoned to headquarters on the surface. The promptness with which fire fighting equipment and material was provided was a big factor in finally extinguishing the fire and illustrates one of the many advantages of a good organization for fire-fighting. Material was transported in mine cars to a point on the main hauling road about 1,200 feet from the fire. It was then carried to the scene of activity by workmen. The first material to be delivered at the fire was a number of fire extinguishers of various types. The contents of 30 to 35 of these were discharged on the fire and with the aid of a small quantity of rock-dust were sufficient to smother the flame temporarily. It was the opinion of several persons who were present when the fire extinguishers were used that the acid-soda type of extinguisher gave more effective results than the two or three other types used.When the contents of all of the fire extinguishers had been exhausted the fire was temporarily smothered, but as there appeared to be danger that the flame would burst forth again, means for completely extinguishing the fire were"

Feb 1, 1929

By N. S. Dalal, B. Jafarl, M. M. Suryan, V. Vallyathan

"The biologic events leading to coal workers' pneumoconiosis (C'WP) are not yet fully understood. There is no good correlation between toxicity studies or animal models with human epidemiologic and pathologic data. Several studies have shown that the severity and prevalence of the CWP in miners correlate strongly with the rank and type of the coal mined. However this has not been found to be the case with laboratory animal models or in vitro studies. In 1980 Russian scientists Artemov and Resnik suggested that the discrepancy may be related to the excessive amount of short-lived free radicals present in freshly generated coal mine dust. Because of their short life, such free radicals would be absent in the ""stale"" coal dust used in most animal experiments. To test this hypothesis we have undertaken a systematic study of the generation, reactivity with oxygen and biological significance of free radicals in coal dust.Electron spin resonance (ESR) was used as a technique for the direct detection of radical production and kinetics of decay. ESR signals from the newly generated radicals decreased with time on exposure to oxygen or when stored in biological buffers at a rapid rate. In vitro biological tests were carried out which suggest that the reaction between the newly generated radicals and oxygen plays a significant role in the sample's cytotoxicity.Materials and MethodsESR measurements were made at X-band (~9.7 GHz) using a computer-controlled Bruker ER200D ESR spectrometer. 11te two coals studied in detail were obtained from the Pennsylvania State University Coal Depository. These were, a bituminous sample, PSOC-1172 (72% carbon) and an anthracite sample, PSOC 867 (95% carbon). Coal particles of several millimeter (mm) dimensions were evacuated to a pressure of ~10-3 mm Hg typically overnight. Without exposure to air, these particles were ground in an agate mortar with an agate pestle for about 30 minutes and then sieved through a 20 \1111 mesh filter before ESR measurements or cytotoxicity studies. As an index of cytotoxicity, hemolysis was measured according to the method of Harrington, with minor modifications. Sheep erythrocytes (2%) were incubated with test samples at 37°C for one hour, and the hemoglobin released was quantitatively estimated photometrically. Additionally, release of alveolar macrophage enzyme lactate dehydrogenase (LOH) was estimated after incubation of the macrophages with the coal particles at different time intervals after the grinding. Enzyme activity was assayed according to the method of Wrobleski and LaDue and expressed as percent of enzyme released in 2 hours per million cells with 1 mg of coal."

Jan 1, 1989

By Stephen C. Tadolini, Thomas M. Barczak

An underground investigation was designed and implemented by the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of pre-driven longwall recovery rooms supported with pumpable concrete roof supports. The pumpable roof supports were instrumented with hydraulic pressure cells to measure support loading. Displacement of the support was also measured to assess the support reaction to ground movements. Movement up to 12.5 m (40 ft) into the roof was measured with sonic probes and multipoint extensometers. Borehole pressure cells were installed in the panel fender and outby pillars to evaluate load transfer. Shield loading was also assessed to determine the impact of the panel fender yielding on face loading. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 3.12 m (10 ft) from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 15-20 cm (6-8 inches) once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 10 m (32 ft) horizon with total deformation ranging from five to 10 cm (2 to 4 inches), indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in instabilities that can lead to catastrophic results. Understanding the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields is providing valuable information for the refinement of the NIOSH Ground Reaction Curve for standing and intrinsic roof support system design.

By Sidney Katell

Several systems have been proposed for the production of synthetic crude oil from oil shale. An economic analysis of one proposed system is presented in this paper. An oil shale complex to produce 100,000 barrels per calendar day of semirefined crude oil will require a capital investment of $426,216,400. This investment includes mining, retorting, intermediate pipelining, and partial refining. A selling price of $3.74 per barrel of product will be necessary to maintain a discounted cash-flow rate of 12 percent.

Jan 1, 1971

By D. A. O'Keefe, M. M. Wong

To obtain beryllium metal of higher purity , flakes produced from electrorefining scrap metal were used as cell feed for a second cycle of electrore fining at 500 ° C in an electrolyte composed of 51.7 mole - percent LiCl , 36.9 molepercent KC1 , and 11.4 mole - percent BeC¹ · Metallic impurities in the flakes totaled more than 108 ppm , the metallic impurities in the metal obtained from the two - cycle electrorefining were , with the exception of 35 ppm of calcium , below the spectrographic determination limits .

Jan 1, 1964

By E. S. Burnett

The temperature entropy (T, S) chart? of thermodynamic properties of nitrogen herewith presented is a complete (1949) revision and a considerable extension of similar charts prepared by the author for use of the helium section of the Bureau of Mines about 25 years previously on the basis of inadequate data then obtaining. During the interval since that early effort, much experimentally determined information on nitrogen properties and behavior has been published, which now permits a more nearly accurate layout and more extensive charting of these relations.

Jan 1, 1950

By P. W. Jerant

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976