Search Documents

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C. 7 Emergency Rescue Hoists There is a need, especially in mine development areas, for portable, on-call, man-rated equipment capable of lifting men through several hundred feet. Wire rope climbing equipment as shown in Figure 37 appears particularly suited to this need. It is portable, weighing approximately 100 lbs. , is currently man-rated for numerous above ground applications and can be electric or air powered. Commercial units currently have a lifting capacity of 1000 lbs. , and can be fitted with bosun' s chairs. Lifting speeds are in the 20-30 FPM range and the equipment is not depth limited. In a situation where miners are unable to climb to the top of a shaft this equipment could rapidly be anchored to the top of the shaft and lowered to them by hand. Since the self contained unit is controlled by the person travelling in the shaft he would be able to negotiate shaft obstruction himself. This would not be possible with other forms of easily deployed free-hanging equipment. Typical manufacturers of this type of equipment are Ohio Hoist Mfg, Co, 321 South Beaver St. Lisbon, Ohio 44432 216-424-7283 Sky Climber Inc. 17311 South Main St. Gardena, California 90248 213-321 -6414

Jan 1, 1976

Coal-bearing beds underlie 23,000 square miles, about one third of Missouri's total area. Twelve out of more than twenty named coal seams have been or are being commercially mined. The remainder are too thin for commercial production. The coal is high volatile bituminous, with reserves estimated to be six billion tons, 1.24percent of U.S. coal reserves. Coal-bearing strata are generally thin seams which can be up to five feet thick. Typically, mined seams are about 28 inches thick. Coal deposits were first mined in Missouri in the 1840s, with the coal used primarily for domestic heating and blacksmithing. Production increased with the introduction of steamboats on the Mississippi. Coal production in 19 17 was six million tons. Production has steadily declined from a high of nearly seven million tons in 1984 to 2.3 million tons in 1991. Declining production is the result of several factors, including competition from other energy sources and the high sulfur content of Missouri coal. Today, coal-fired electric generating plants are the biggest consumers of Missouri coal. The Missouri regulatory program was conditionally approved November 21,1980, and fully approved January 17,1983. Its Abandoned Mine Land program was approved January 29, 1982.

Jan 1, 1992

By W. D. Bensema, J. W. Adams

A portable, multichannel battery-operated mine-permissible measurement system was developed to measure the rms magnetic-field noise spectrum in the frequency range from 100 Hz to 375 kHz. During each measurement, the entire spectrum is measured simultaneously through the use of time-domain recordings which are later analyzed by Fast Fourier Transform processing. Dynamic ranges of 60 dB in a 125 Hz bandwidth are obtained for spectra covering the range from 100 Hz to 100 kHz. The method also allows a three-dimensional display of the way spectrum occupancy changes with time. Calibration and correction procedures allow absolute field strength measurement with an uncertainty of not more than 3 dB. We feel that further analysis of the system errors will allow this uncertainty to be reduced to less than 1 dB. Ambient magnetic field noise spectra covering frequencies from 100 Hz to 100 kHz are given for several underground coal mine locations. Examples are also given of magnetic field noise on the surface above the mine, noise in the mine face area, noise radiated by specific equipment, the voltage spectrum found on a 600 V dc trolley wire, and noise picked up simultaneously on loops and on roof support bolts.

Jan 1, 1973

By John L. Reuss

A laboratory study was conducted by the Bureau of Mines to investigate the technical feasibility of decomposing hydrous magnesium chlorides by using a steam pyrohydrolysis technique. This procedure consisted of injecting steam into the atmosphere of a decomposition furnace containing samples of hydrous magnesium chloride and determining the rate of hydrolysis by measuring the rate of chloride evolution. The variables investigated were temperature, amount of water vapor in the decomposition atmosphere, and hydration stage of magnesium chloride. The application of steam was shown to accelerate both the rate and completeness of magnesium chloride decomposition reactions. For example, when magnesium chloride hexahydrate is exposed to a furnace temperature of 600' C in an air atmosphere for 20 minutes, the decomposition is 37 percent. Under identical conditions in a steam atmosphere, the decomposition is in excess of 70 percent. The magnesium oxide produced by the steam pyrohydrolysis of magnesium chloride dihydrate at 800° C contained 98 percent magnesium oxide. Based on magnesium oxide composition, this is equivalent to that of burned magnesite produced at temperatures in excess of 1,300° C. To demonstrate the quality of the product on a practical basis, metal reduction tests have shown it to be equivalent to reagent-grade magnesium oxide as a carbothermic reduction feed material.

Jan 1, 1974

Improve the field-of-view into the front-right blind spot for drivers of large haulage trucks, thereby reducing the growing collision hazard in surface mines. Approach Reduce the glare problem found in the first generation fresnel lens blind area viewer design by eliminating the upward-looking section of the fresnel lens and adding a rear hood to reduce backlighting. How It Works The first generation blind area viewer was developed and in-mine tested as an aid to improved visibility for large haulage trucks. Other aids were improved left-and right-hand mirrors. Evaluations showed that a blind area viewer mounted on the right-front of the radiator deck was effective and was readily accepted by drivers. Nevertheless, because glare was a problem under certain conditions, a low-profile viewer was developed. Glare control louvers from the earlier design were kept and a backlighting glare control hood was added. The height of the hardware was reduced by eliminating the top three inches of the fresnel lens. This portion of the lens contained an upward-looking segment which originally was thought to be needed so the driver could see the horizon when he looked through the viewer and be better

Jan 1, 1982

The instrumentation specification in the National Academy of Engineering (NAE) report of March, 1970, set forth some rather general guidelines that the seismic surface system should follow. The fact that there was no comparable equipment in existence at that time, and the need to produce a system from presently available equipment, was spelled out in that document. The features that the system should include were listed, and included: • Quick and simple deployment • Portability • Battery-powered operation • All-weather operation • Computational simplicity and speed • High reliability and long shelf-life • Dual service for location and communication • Adaptability to widely varying seismic velocities. topography, and geologic structures • Minimum maintenance • Capability of continuous operation for extended periods, and • Reasonable cost Since that report, there has been a substantial amount of field work addressing the trapped miner detection and location problem carried out by Westinghouse Corporation under contract with the Bureau of Mines. Two complete surface systems have been designed, built, and field tested and substantial documentation has been produced on the mine environment and background noise using these systems. These systems, built from off-the-shelf equipment, have been designed with maximum flexibility in mind in order to explore what con¬figuration a field unit should have.

Jan 1, 1974

By T. G. Carnahan

The Bureau of Mines conducted laboratory-scale weathering research on a leach residue containing elemental sulfur and mixed metal sulfides. Experiments were performed to determine pH and impurity element concentrations in the effluents as functions of time and to determine the effects on effluent concentrations of mixing the residue with dolomite tailing material. Four 800-day tests were conducted simultaneously. Soluble metal concentrations, especially zinc and copper, were excessive in the effluents from washed and unwashed samples of the residue. Concentrations of up to 20 g/l of Zn and 12 g/l of Cu were obtained. The pH values of the unwashed and washed residue effluents at the completion of the experiments were 2.8 and 1.9, respectively. Sulfuric acid from oxidation of pyrite caused the pH decrease. Mixing unwashed residue with dolomite tailing to maintain a near-neutral pH minimized the heavy metals content in the effluents. The pH in the dolomite tests increased slowly after the first 360 days and attained values of 7.8 and 8.2, respectively, for tailing containing 1 pct leach residue and for tailing devoid of leach residue. Dissolved zinc and copper did not exceed 0.10 g/l of Zn and 0.001 g/l of Cu.

Jan 1, 1982

Aid mine operators as well as mine inspectors in making quick but sufficiently accurate measurements of the rock dust content of coal/rock dust mixtures. The Problem Past research has shown that accumulations of volatile coal dust in underground coal mines can be rendered non-explosive by dilution with chemically inert rock dust (usually limestone). Consequently, rock dusting is required by law in U.S. underground coal mines. However, mine officials and inspectors have no quick and reliable means to determine whether enough rock dust has been applied to achieve a mixture that is in compliance with the law. Even the compliance tests used by the Mine Safety and Health Administration (MSHA) are slow and involved. MSHA assures that a mine has been rock dusted adequately by collecting samples from rock dusted areas of the mine and sending the samples to a laboratory for analyses of the inert-dust content. The analyses may not be completed for more than two weeks, during which time the mine in question might be inadequately protected against coal dust explosions. To solve this problem, the Bureau of Mines devised a quick, simple and reliable device that can immediately determine the rock-dust content of a mixture of coal and rock dust.

Jan 1, 1985

By Jami M. Girard

INTRODUCTION Slope stability accidents are one of the leading causes of fatalities at U.S. surface mining operations. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to reduce the fatalities associated with slope failures and other unexpected failures of ground. The purpose of this paper is to introduce various warning signs of slope instability so operators are better able to recognize hazards. The most common slope monitoring equipment and practical methods of installation are discussed as well as the limitations of these systems. CONSEQUENCES OF SLOPE FAILURES Unexpected movement of ground causes the potential to endanger lives, demolish equipment, or destroy property. Between 1995 and 2001 (2nd quarter), 34 fatalities were caused by ground instability. This accounts for approximately 15% of all surface mine fatalities (Figure 1). These figures include fatalities classified by the Mine Safety and Health Administration (MSHA) as “fall of face or highwall,” “powered haulage,” “equipment,” and other MSHA accident categories, where the primary cause of the accident was unanticipated movement of the ground. This includes fatalities resulting from bench and highwall failures, rock falls, waste dump and stockpile failures, and the collapse of unknown underground workings. [ ]

Provide reasonably priced, reliable fire protection for AN-FO haulers. Approach An automatic fire sensing and suppression system for AN-FO haulers was developed and on-vehicle tested. How It Works The system works in two ways to protect personnel from dangerous and unpredictable AN-FO fires. First the system senses and suppresses fires on the truck before they spread to the AN-FO in the bunker. This design was chosen because AN-FO truck fires generally start when combustible liquids (such as diesel fuel, hydraulic fluid or lubricating oils) are ignited by hot surfaces mainly on three areas: the engine, the transmission or the power take-off. These fires are quickly sensed by a linear temperature sensor strung throughout these three areas. The system then warns the operator and automatically suppresses the fire by discharging 30 pounds of multipurpose dry chemical extinguishing agent through a network of fixed hoses and nozzles. Second, this system includes six spot thermal sensors mounted inside the bunker on the truck to monitor the AN-FO temperature in case a fire does spread to the bunker area. If the bunker temperature rises to 190° F, a loud siren is sounded to warn nearby per-

Jan 1, 1981

By Jeran Paul W., Michael A. Trevits

Subsidence data gathered by the U.S. Bureau of Mines over a series of longwall panels in the Pittsburgh Coalbed were studied to obtain insight as to the role of time in the subsidence process. It was found that subsidence began essentially with undermining and was completed within 1 year. The progress of the subsidence was dependent upon location above the panel. Subsidence in the central area of the subsidence trough, where subsidence is the greatest, was about 90 pct complete by the time the face had progressed a distance equal to one overburden thickness beyond a particular surface point. For a point over the rib of the longwall panel, the subsidence was only about 60 pct complete at this time. Data from three other sites in the northern Appalachian Coal Basin were analyzed to determine if an anomaly or the true characteristics of the subsidence process had been observed. All sites behaved similarly in the central portion of the subsidence trough. However, the subsidence of points over and adjacent to the ribs of the longwall panels was site specific. The fact that movement across the width of the panel was not uniform should be taken into account in assessing damages or the potential for damages resulting from mining-induced subsidence.

Jan 1, 1995

By J. J. Cummins

Green River oil shale previously extracted by benzene was heated at 150°, 200°, 250°, 300°, and 350° C for 0.5 to 360 days to determine the rate at which kerogen degrades to thermal products, the types of thermal products formed, and the effect of prolonged low-temperature heating (preheating) upon subsequent assay yields. Thermal decomposition of kerogen at 150° to 350° C is treated as a first-order reaction. The specific reaction rate for kerogen decomposition increases from 2.2 X 10-4 per day at 150° C to 2.0 X 10-1 per day at 350° C. The calculated kerogen activation energy is 19 kcal. Variations in the rate of formation of individual type components of the pyrolytic products were found. Carbon balances show an increase in the amount of kerogen converted to bitumen and oil (from assay of preheated oil shale) as the temperature of preheating increased from 150° to 350° C. Total product from shale preheated at temperatures of 150° and 200° C gave less than 100 percent of Fischer assay yields while the total products from shale preheated at temperatures of 250° to 350° C gave greater than 100 percent of Fischer assay yields.

Jan 1, 1972

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By R. C. Gabler

Laboratory tests on a combined nitrogen roast--two-stage leach--electro-winning approach show promise as a possible process for recovering copper, sulfur, iron oxide, and valuable minor metals (gold, silver, and molybdenum) with a minimum impact on the environment. During the nitrogen roast at 800° C, 15 to 20 percent of the sulfur together with a significant fraction of the volatile elements, such as arsenic, bismuth, lead, and zinc, are removed from the chalcopyrite concentrate. The resulting calcine, consisting of 8-chalcopyrite, troilite, and a bornitelike structure, is leached with hydro-chloric acid to remove 70 to 85 percent of the iron. The digenite in the leach residue is dissolved in an oxygen-saturated, spent sulfate electrolyte. Using a graphite 'anode plus sulfur dioxide to reduce interference from ferric iron, copper of 99.99+ purity is electrowon at current efficiencies of 88 to 92 percent and a cell voltage of 0.4 to 0.5 volt. Copper recovery for the overall process is 98 to 99 percent. Sulfur is obtained in the elemental form from the roasting and leaching steps. Iron can be recovered from the hydro-chloric acid leach solution. Gold, silver, and molybdenum are concentrated in the silica residue from the spent electrolyte leach.

Jan 1, 1975

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 11,069-acres of the 12,290-acre Eldorado Wilderness Study Area (NV-050-423) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, adjacent to and northeast of the town of Nelson. There are inferred subeconomic resources on the Paul (gold, silver), Bel (gold, silver), Big Horn-Inez (silver, copper, lead, zinc) claims, and Montezuma (gold, silver, copper, lead, zinc) patented claim group in the Eldorado study area. Because of lack of exposures, tonnage and grade on these properties could not be determined. No resources were identified for the other five properties examined in the area. The southern two-thirds of the area is in the Eldorado mining district, a base- and precious-metal district which has been intensely explored for over 100 years. Nine claim groups were examined in the study area. Eight claim groups are within the Eldorado district and include the Montezuma (patented -M.S. 3966), Bel, Eldorado, VAR, SINJUN, Paul, Rusty Bit, and Big Horn-Inez. One property, the Flintstone claim group, is north of the Eldorado mining district at the north end of the study area.

Jan 1, 1988

By Kenneth H. Johnston

Information on oil and water production, volume of water injected, core analyses, and well completion data was collected on 28 Red Fork sand water-flood projects for comparison and evaluation of results. An average water injection efficiency of 35 percent, an average water-injected to oil-produced ratio of 16.8:1, and an average loss outside the flood pattern of approximately 45 percent of the injected fluid resulted in an oil recovery to January 1, 1969, of only 5.6 percent of the pore volume, or 9.1 percent of the initial stock-tank oil in place. The principal causes of poor oil recovery from these projects are the losses of large quantities of injection water from the flood patterns through oriented, natural fracture systems or zones of high permeability and excessive channeling of injection fluids from input wells to oil wells. For more efficient operation and a higher percentage of oil recovery from the Red Fork sand and other low-permeability-sand waterflood projects, directional orientation of both induced-and natural-fracture systems should be determined during early development. The success of a low-permeability-sand waterflood project depends to a large extent upon the orientation of the injection wells with the fracture system.

Jan 1, 1970

By William R. Sharp

This Bureau of Mines report details a technique for aiding the engineer with the long-range design of an underground mine. The method is based upon the assumption that sufficient data are available to assign numeric values to some finite number of mineralized blocks; assignment of numerical values is problem dependent. By assigning appropriate weighting schemes, the algorithm developed in this report may be used to solve the optimal end-of-life underground mine layout, design least-cost electrical layout networks and efficient material handling networks, find least risk escape routes in the event of an accident, etc. The method is based upon the assumption that sufficient cost and geologic data is available to build a detailed mineral block inventory of the mineral deposit. It is further assumed that the cost assigned to any minable unit is independent of the neighboring blocks. The basic approach relies upon concepts and ideas from the theory of networks. To make the approach user oriented, a computer program is included and discussed. The computer code is written for an orthogonal, three-dimensional set of blocks. Computational costs and experience indicate that the program could be of great benefit in evaluating large complex mineral properties from the viewpoint of predesigning an underground mine layout.

Jan 1, 1974

By J. H. Jansky, P. W. Jeran, G. L. Hassett, M. C. Irani

This Bureau of Mines report tabulates methane emissions from U.S. bituminous coal mines with daily emission rates of at least 100,000 cfd according to States, counties, and coalbeds. Most of the methane emitted is from mines in the Appalachian States. Total daily emissionin 1975 was 216.3 MMcfd, compared with 227.0 MMcfd in 1971 and 214.5 MMcfd in 1973. Thirty counties in nine States had daily methane emissions of 1 MMcfd or more, These emitted 93 percent of the total methane. The highest emissions were from Monongalia County, W. Va,, which accounted for 18.9 percent of the total. This was followed by Marion County, W. Va., 9.6 percent; Buchanan County, Va., 8.5 percent; Jefferson County, Ala., 6.1 percent; and Washington County, Pa., 5.9 percent. The Pittsburgh coalbed emitted 45.7 percent of the total methane, followed by the Pocahontas No. 3 coalbed with 12.9 percent. The report lists 196 mines, of which 60 had daily methane emissions of 1 MMcfd or more. Included in this compilation are the identification and thickness of the coalbed, methane emission, coal production and ventilation rates, number of drifts, shafts, and slopes used for ventilation purposes, shaft depth, age of mine, and gas-to-coal ratio.

Jan 1, 1975

By Robert B. Schluter

The Bureau of Mines investigated separating copper-nickel mattes to recover a copper-rich fraction suitable for processing by conventional copper metallurgical processes and a nickel-rich fraction suitable for processing in a hydrometallurgical nickel circuit. Distribution of cobalt and precious metals between the copper and nickel fractions was also determined. A matte containing a nominal 65 pct Cu, 9 pct Ni, 4 pct Fe, and 20 pct S was separated into a copper fraction that comprised 80 pct of the matte weight and contained 70 pct Cu and <1.5 pct Ni, plus a nickel fraction that contained 40 pct Ni and 30 pct Cu. Recoveries of copper and nickel into their respective fractions were 90 pct and 87 pct. These results were obtained in a laboratory flotation cell at a matte grind of 90 pct minus 500 mesh and a pH of 12.4, using 1.7 pounds DPG (diphenylguanidine) per ton of matte as collector and frother. Magnetic separation was used to remove metallic iron-nickel alloy from the copper fractions. Distribution of cobalt was about 70 pct to the nickel fraction and 30 pct to the copper fraction. Silver reported predominately to the copper fraction, while Au, Pt, and Pd were essentially entirely recovered in the nickel fraction.

Jan 1, 1982

By Carla A. Kertis

Because coalbed discontinuities often pose serious economic and safety problems in underground coal mines, criteria were documented for the recognition and prediction of discontinuities in advance of mining. Pennsylvanian strata in Indiana and Armstrong Counties, PA, were deposited as part of fluvio-deltaic complexes with channel-phase sandstones as the predominant type of coalbed discontinuity. Coalbed isopach maps constructed for this study delineated numerous want areas (areas of no coal) with elongate to linear geometries. A comparison of coalbed isopach and corresponding sandstone isolith maps of the study area revealed many examples of a thick-sandstone, thin-subjacent-coalbed relationship. Nearly 60 pct of the want areas in the study area were found to lie subjacent to thick (> 20 ft [6 m]) sandstone accumulations. In addition to erosion of the coalbed, channels may contribute to coalbed splitting, coalbed thinning over paleotopographic highs, abnormal coalbed thick- nesses, and deterioration of coal quality. If these features are considered, then approximately 80 pct of all interruptions in the economic coalbeds in this area result from channel activity. By using the criteria developed in this study and described in this Bureau of Mines report, the occurrence of coalbed discontinuities may be predicted and anticipated in advance of mining.

Jan 1, 1985