Search Documents

By C. M. K. Boldt, R. L. Levens, A. D. Marcy

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface are aexposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 1995

By Thomas V. Falkie, R. Venkataramani

The empirical nature of this investigation required measurements of variables under operating conditions in underground coal mines. The variables to be measured were based on the postulated character¬istics of the loading function, as described in the previous chapter. One class of variables presumed to influence the loading function are geological variables. Accordingly, the sites for data collection were selected in different bituminous coal seams at dispersed locations in order that variation in geological conditions would exist. Seven mines in central and western Pennsylvania and one mine in northern West Virginia were selected as data collection sites. Five different coal seams were represented by these mines. The remaining classes of variables - geometric, mechanical, and procedural - were measured as they occurred in the mines. A description of the measurements, and the conversion of these measurements to forms which could be-analyzed for effect on the loading function is given. Mining Dimensions At the underground working face, the following dimensions were measured: a. Thickness of coal excavated. b. Thickness of shale excavated. c. Total height excavated. d. Width excavated. e. Depth of penetration of each machine cut. With the exception of the last of these dimensions, all were measured

Jan 1, 1972

By Charles L. Kimbell

This study is intended to serve three roles. First, it represents a global overview and summary to supplement and complement the five regional companion volumes of the 1991 edition of the Minerals Yearbook International Review. In this regard, it also extends previous time series under this title that appeared as the introductory chapter to the international volume of the Minerals Yearbook from the inception of that volume in 1963 until it was subdivided into separate regional volumes in 1989. The basic statistical presentations herein generally contain data through and including that for 1991, although in a few instances the most recent statistics are those for earlier years because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting the world's mineral industry that have occurred between the end of 1991 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

Determine the extent of upper extremity cumulative trauma disorders (UECTD's) in the U.S. mining industry. Background UECTD's are injuries that develop gradually over a period of time as a result of repeated stress to a particular body part without adequate time between stresses for full recovery to occur. The stresses that contribute to UECTD's may occur because of the following work components: awkward position of wrist or arm, excessive manual force, high repetitions of manual movement and effort, cold environment, and vibration. Cumulative trauma injuries to the arm and hand have become an ever growing concern among safety and health professionals in a number of different industries and work settings, such as meatpacking operations, assembly-line work, and keyboarding. Mine workers arc also exposed to a combination of stressors and work design deficiencies that result in arm and hand injuries. For example, certain job tasks and environments, such as that of an underground jackleg driller, expose miners to segmental (hand-arm) vibration and cold temperatures. Operators of underground mobile equipment, such as scoops and trams, regularly have their hands in direct contact with vibrating levers and controls.

Jan 1, 1992

By W. F. Marshall

The effect of engine parameters on exhaust emissions from two diesel engines was studied experimentally. Fuel-injection characteristics and intake air conditions were considered as parameters influencing the emissions. Emphasis was placed on the effect of parameter variations on nitrogen oxide (NOx) emissions, because diesels generally emit very low levels of carbon monoxide (CO) and unburned hydrocarbons. Emissions other than NOx were at lowest levels when the engines were adjusted for best performance. NOx emissions can be diminished somewhat through variation in fuel-injection characteristics, but there generally are penalties in emissions of CO, smoke, and unburned hydrocarbons or in engine performance. Temperature and composition of intake air have a significant effect on NOx emissions. Levels of NOx are reduced by recirculating the exhaust gas or by adding water to the intake air stream. However, the rate of water added or exhaust gas recirculated must be limited to prevent the degradation of engine performance and increased emissions of CO and smoke. At high exhaust recirculation rates, levels of CO and smoke were increased such that it was necessary to derate the engine and also to use a catalytic system for oxidation of CO.

Jan 1, 1971

By A. R. Taylor

Using solution calorimetry, the following heats of reaction were determined: (1) NaCN(c) + 1/Cu20(c) + 129H20(l) ? CuCN(c) + NaOH?128.5H2O ?H = -13.44±0.10 kcal/mole, (2) HCN(2) + NaOH?128.5H20 ? NaCN(c) + 129.5H20(l) ? = -2.52±0.02 kcal/mole. From these reactions, the heats of formation for CuCN(c) and HCN(2) were calculated to be 22.7±0.4 kcal/mole and 24.9±0.4 kcal/mole, respectively. Reaction 2 was made to check the consistency of literature values for heats of formation of HCN and NaCN. Adiabatic calorimetric measurements between 10° and 400° K showed the entropy and heat capacity of CuCN(c) to be 21.51±0.06 eu and 14.58±0.04 cal/mole deg, respectively, at 298° K. A broad anomaly in the heat capacity was found in the temperature range 285°-320° K. The heat of transition associated with this anomaly was less than 1 cal/mole, the sensitivity of the measurements.

Jan 1, 1971

The U.S. Department of Labor?s Mine Safety and Health Administration (MSHA),through its winter alert program, warns U.S. mine operators and miners at underground coal mines of workplace hazards that can arise when the weather turns colder. MSHA records indicate that, historically, most explosions in underground coal mines occur during winter months. ?The changes in weather can increase the risk of fatal accidents,? says David G. Dye, Acting Assistant Secretary of Labor for Mine Safety and Health. ?Each miner and mine operator must take individual responsibility to eliminate the kinds of hazards that can cause fatal accidents in the workplace. Safety is not the other guy?s job?safety begins with you.? In fact, MSHA?s slogan for this year?s campaign is ?Winter Alert Starts Now and Safety Begins with YOU.? This message reminds miners and mine operators of the risks of colder weather and educates them about helping to reduce risks and hazards. ?Safety requires the joint effort of both management and labor,? Dye says. ?Everyone at the mine site must see safety as an individual value and act to ensure a safe working environment.?

Jan 1, 2006

Reduce the number of conveyor-related accidents in the mining industry by providing recommendations for effective operation of conveyor belt cleaning systems. The Problem Troughed belt conveyors provide effective, and efficient materials transport and their use has increased throughout the mining industry. Carryback, the spillage that accumulates under the belt, is a problem even with belt cleaning systems installed. Mining personnel are exposed to safety and health hazard; as they attempt to clean up this spillage. Approach To investigate the influence of metal-segmented-blade belt cleaners on the amount of carryback spillage, the. Bureau identified and tested the following parameters: (1) amount of pressure applied to the cleaner blades, (2) friction between the blades and conveyor belt, and (3) wear rates of different metal blades. The test parameters were quantified by recording the amount of carryback material passing the metal cleaner blade, and the weight loss of the blades. The data collected were used to identify the following critic d operational parameters of a segmented-blade conveyor cleaner system: (1) the existence of an optimal operating pressure for the conveyor and cleaning systems and (2) elimination of recessed patterns on the working side of the conveyor belt.

Jan 1, 1989

By M. J. Ferrante

Relative enthalpies of cuprous iodide (CuI) were measured at the Bureau of Mines to provide thermodynamic data for the advancement of min-eral technology. Enthalpy measurements between 298.15 and 1,396.3 K were made with a copper-block drop calorimeter. The temperatures of transition were measured by differential scanning calorimetry (DSC). Reversible transitions were determined at 643 K with a standard enthalpy of transition [(6Htr)] = 0.74 kca1/mol, at 679 K with a [6Htr = 0.65 kca1/mo1, and at 868 K] with a standard enthalpy of fusion [(6H~) = 1.895 kca1/mol.] Tabulated values are listed at selected temperature increments from 298.15 to 1,600 K for the standard relative enthalpy (HO -H298), heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)!T]. The enthalpy data are also given in the form of equations and combined with thermodynamic data from other investigations to derive values of standard entha1pies of formation [(~HfO)], Gibbs energies of formation [(6GfO)], and logarithms of the equilibrium constants of formation (log Kf).

Jan 1, 1987

By John R. M. Hill

The Bureau of Mines performed elastic-plastic, finite-element analyses to investigate the support performance of hydraulic backfill. A mathematical model was developed for two vertically adjacent stopes separated by a sill pillar. An exact duplicate of a working stope was not intended; however, the model did simulate a working stope to the extent that field measurements from an active stope could be used for comparative purposes. Using a predetermined mining sequence, the computer analysis simulated the mining operation as a series of incremental cut-and-fill steps. Computer results included a complete history of stope closure and pillar stresses throughout the mining sequence. With the mining sequence and rock properties held constant, three separate analyses were made using varying backfill properties. These cases included no fill,-low-to-medium-quality fill, and medium-to-high-quality fill. Results of these analyses show decreases in stope closure and pillar stresses as the backfill quality increases, thus reducing the possible occurrence of rock bursts. Predicted stresses within the backfill compare favorably with field measurements. A relationship between maximum stress normal to the stope wall and the ratio of relative fill stiffness to relative rock stiffness was also indicated.

Jan 1, 1974

Identify specific sources and the relative levels of contribution of various components of longwall shearer operations to the total airborne respirable dust generated during mining. Approach A research investigation was conducted in two phases by the Bureau of Mines at five mine sites to identify specific dust sources and their relative importance during long-wall shearing operations. During phase I of the project the specific longwall mining elements identified for evaluation were: cutting, sumping, tramming, conveying, and moving roof supports. During phase II of the project, two dust sources were evaluated: clearance ring cutters cutting in six-inch web width increments, and loading operations. Investigation Results As a result of dust measurements, the gage cutters were determined to be the major dust-generating source on the shearer. These cutters, at 6-inch web depth, produce three times as much dust per unit volume as is produced at 30 inches full web depth. The following list of averaged values for the mines tested shows that shearer cutting generated averaged dust levels four times as high as those generated by conveying, and approximately five times as high as those generated in moving roof supports.

Jan 1, 1984

Determine what diameter piping is necessary to obtain sufficient water flow to spray nozzles used for dust suppression. Approach A simplified, diagrammatic method of calculating the flow of water through a proposed system consisting of a supply line and two banks of spray nuzzles is outlined. How It Works The pressure versus flowrate of the supply at the tapping point must be known or measured. The supply curve of typical city water at a 1 ¼ -inch pipe outlet is shown by the lowest curve in Figure 1. A supply curve for a typical pump fed from an open sump is shown by the middle curve. The combination of these, the supply curve of a pump fed by the city water supply is shown by adding the lower two curves to get the upper curve. A pump supply curve showing flowrate versus pressure is usually supplied by the manufacturer. The water supply line flow curve can be determined by measuring the time required to fill a 55 gallon barrel at various valve settings to determine flow, and by measuring corresponding pressures at the valve with a gauge.

Jan 1, 1979

By Paul T. Allsman

THE THREE words, research, mechanization, and automation are keynote words for mining technology during 1962. Basically interrelated, they not only express the major technologic developments in mining but are the signposts pointing out the road ahead. The process represented by each of these words is evolutionary rather than revolutionary, but developments during the past year indicate a climactical stage has been reached in the process of evolution. Mining research has progressed beyond the stage of academic discussion and is a programed activity within the Federal Government,3 the mining colleges,4 and many of the large mining companies.5 Research was a major agenda item at various national and international mining meetings in 1962. A list of these meetings would include such diverse locales as the Workshop and Symposium on Computers and Computer Applications in Mining and Exploration at the University of Arizona in March; and the 5th Rock Mechanics Symposium at the University of Minnesota, in May; the Rock Mechanics Symposium at McGill University, Montreal, Canada, in September; and the Colloquium XIII, International Society for Rock Mechanics, at Salzburg, Austria, in November.

Jan 1, 1963

Detect hazards associated with abandoned mine openings through the use of integrated geophysical technology. Background Many abandoned mines in the U.S. present hazards to the public. The first step in abatement of these hazards usually requires locating the abandoned workings. Recent Colorado legislation resulted in a concerted effort aimed at mitigating the hazards associated with abandoned mine workings. The Colorado Department of Natural Resources-Mine Land Reclamation Division (CDNRMLRD) is responsible for locating and backfilling abandoned mine openings such as shafts, adits and collapsed features. Many shafts and adits can be located by inspection, other openings give little or no surface expression and must be located by drilling, or through the use of geophysical methods. A common method used for locating underground mine workings is to drill throughout the suspected area. However, it is prohibitively expensive to drill holes at the spacing needed to detect backlilled shafts and small voids associated with caving and/or chimneying. It may also be dangerous to move heavy equipment over shallow mined-out workings. Geophysical investigations that employ only a single method have had mixed success in detecting hazardous abandoned mine land cavities.

Jan 1, 1991

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

Provide optimum visibility of mining operations while maintaining protection and comfort for machine operators. Approach A cab with hydraulically powered variable-height control was developed and used on a loading machine in underground operations. How It Works The cab is attached to the vehicle on a horizontal trunnion located near the forward end of the cab. A hydraulic cylinder, controlled by the operator from inside the cab, pivots the cab about the trunnion providing variations of up to 16 inches in elevation. The nominal tramming position of the cab is with its underside 6 inches above the mine bottom. From this position the cab can be pivoted up, or down, so that its back end is elevated 10 inches, or lowered to the floor. (See Figure 1.) The cab encloses the operator for protection against both overhead and lateral obstructions, and it raises or lowers, allowing the operator to select the most advantageous cab height. The cab is angled inboard 30 degrees to the machine line of direction. The operator's seat swivels to allow view of the conveyor during loading. All controls are located within the cab and move up and down with it.

Jan 1, 1978

By J. C. Edwards

The Bureau of Mines developed a mathematical model that decribes the interaction of an automated breathing and metabolic simulator, or lung, with a self-contained· self-rescuer that is supplied compressed oxygen. The model can be used to predict the gas partial volumes of 0z, Nz, and COz in the lung and in the self-rescuer breathing bag for a prescribed metabolic state that characterizes the lung. Nonlinear rate equations are used to describe the temporal evolution of the gas partial volumes. A numerical procedure was established with a FORTRAN computer program to solve these equations, which correspond to a given metabolic state. Examples are presented of applications of the model to predict bag volume and bag oxygen concentration changes with time when the bag is controlled by an automated breathing simulator. Under certain restrictive conditions, the model equations can also be used to analytically pre-dict the time required for the bag to reach a maximum or minimum volume. The model equation in this latter case was extended to transi-tions between metabolic states, with transitions described as exponential growth or decay processes.

Jan 1, 1985

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

Promote safer and more efficient mine operations by providing communications between personnel located anywhere in the mine. Approach A radio communications system was designed which takes advantage of existing mine wiring such as telephone lines or electric power cables. The existing wiring distributes radio signals throughout the mine, making communications possible between roving miners, vehicle operators, dispatchers, and other personnel. How It Works Research has shown that medium frequency (MF) signals (300 KHZ-3 MHZ) can couple onto and re-radiate from nearby conductors. This effect is known as parasitic coupling and re-radiation. In a mine, these conductors include electric power cables, control lines, telephone lines, trolley lines, as well as metal water and air pipes Since all underground mines require these conductors for normal operations, the necessary network already exists and expands automatically as the mine is developed. A radio communication system has been developed that uses the parasitic coupling and re-radiation characteristic of MF. Using this system, whole mine radio coverage can be achieved without the need to install or maintain communication lines. The system consists of mobile transceivers for roving personnel and vehicles, and fixed-location base radio stations and repeaters.

Jan 1, 1982

By R. C. Ellman

Significant effects of in-the-mill drying on the pulverization of lignite have been demonstrated in an experimental impact-type pulverizer by tests in which the primary variable was temperature of the sweeping gas. Reduced power requirements and increased product fineness were observed as the extent of drying was increased. Pulverization with in-the-mill drying was studied in comparative tests made on lignites from five mine sources. All of the lignites responded in a similar manner; however, differences in the pulverizing characteristics of the individual lignites were significant. For one lignite, the electrical input to the pulverizer driving motor with minimum sweeping-gas temperature was 33.9 kw.-hr. per ton, decreasing to 14.0 kw.-hr. per ton with a sweeping-gas temperature of 658° F.; for another lignite, at comparable operating conditions, the electrical input decreased from 59.1 to 19.0 kw.-hr. per ton. In the first case, the product fineness increased with increasing temperature of sweeping gas from 65.2 to 79.2 percent through a 200-mesh sieve, and in the second case, from b2.7 to 86.9 percent through a 200-mesh sieve.

Jan 1, 1962