Search Documents

By Samuel W. McNary

In August 1984 the U.S. Bureau of Mines conducted a study of the mineral resource development potential of the Badger Canyon-Antelope Creek area, within the Boulder-Pioneer wilderness study area, about 5 miles northeast of Ketchum, 10. The purpose of this study was to investigate in greater detail an area which was designated by the U.S. Geological Survey (USGS) and the Bureau as having a moderate mineral resource potential for zinc, molybdenum, lead, and silver, and a low potential for copper. One hundred twenty-eight soil samples were taken along a 6,2S0-ft traverse on the ridge separating Badger Canyon and Antelope Creek. 5 Five rock samples were collected from old prospect pits and mineralized outcrops. All samples were analyzed for gold. Silver, copper, lead, zinc, molybdenum, arsenic, antimony, vanadium, and mercury. The metal concentrations in the soil samples along the traverse are irregularly distributed. Samples collected near old prospect pits tend to be high in lead and zinc, undoubtedly a reflection of underlying galena-and sphalerite-bearing quartz veins. All of the copper and mercury values in the soils are less than the detection limit, as are most of the lead, molybdenum, and antimony values. Except for lead and zinc values, the metal concentrations in the rock samples are low. Galena and sphalerite were observed in quartz vein samples collected at the old prospects. The results of the study indicate that the galena-sphalerite-bearing quartz veins and veinlets are too narrow, widely-spaced, and low in metal values to be economic. Low concentrations of metals in the soil and rock samples, combined with the lack of major mining activity in the past, indicate that the area has a low likelihood for economic development.

Jan 1, 1986

By Alan R. Buehler

A mineral survey of the 20,792-acre Sand Butte WSA (Wilderness study Area), ID-57-8, was conducted by U.S. Bureau of Mines personnel in 1985, at the request of the Bureau of Land Management. The WSA is in Lincoln County, south-central Idaho, about 15 miles south-southeast of Carey. There are no mines, prospects, or claims within the WSA. Basaltic lava is the only rock type exposed within the WSA. The only mineral resource is a few tons of a platy variety of lava (slab pahoehoe) which is suitable for use as decorative stone. Similar slab pahoehoe, produced from other lava fields in southern Idaho, retails for approximately $125/ton. The deposit in the WSA is too small to be mined commercially but may have value to consumers who gather their own decorative stone. INTRODUCTION A mineral survey of the Sand Butte WSA (Wilderness Study Area) 1/ was conducted in June 1985 by the USBM (U.S. Bureau of Mines) and the USGS (U.S. Geological Survey) at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will he used to help determine the suitability of the WSA for inclusion into the National Wilderness Preservation System. The immediate goal of this and other USBM mineral surveys is to provide data to the President, Congress, government agencies, and the public for land-use decisions. The long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By T. J. Driscoll

In this Bureau of Mines investigation, the electrochemical polarization behavior of Fe and Fe-1BCr has been characterized in rigorously controlled 1[N] H2S04 solutions stirred with oxygen or an inert gas. Samples that under-went various levels of corrosion or passivation were examined using Auger electron spectroscopy (AES) and ion sputtering. Passivation of iron occurred at a potential of approximately 0.6 volt (1) in poorly stirred, oxygen-saturated solutions for forward polarization (scanning from cathodic to anodic potentials); (2) in pH-adjusted (increased), well-stirred, oxygen-saturated solutions for forward polarization; and (3) in well~ and poorly stirred, oxygen-and helium-saturated solutions for reverse polarization. Passivation of Fe-18Cr occurred at a potential of approximately -0.1 volt in helium-, nitrogen-, and oxygen-saturated solutions for all cases of forward polarization and most cases of reverse polarization. Elemental depth profiles obtained from AES sputtering measurements indicated that films or adsorbed species were present on iron samples in solution subjected to open-circuit, active, and transpassive corrosion, cathodic reduction, and passivation. This conclusion was reached by considering the distribution of the solution species, primarily sulfur, in the films, which were composed primarily of iron and oxygen. Sulfur was present throughout the films on actively corroding samples, in the outer regions of films of passive and transpassive samples, and on the film surfaces of open-circuit and cathodically reduced samples. For Fe-18Cr, sulfur was found on the surfaces of films on passive samples only, indicating that only the passive samples had films on their surfaces in solution. The films on electropolished and passive Fe-1BCr samples had the largest chromium concentrations, estimated to be approximately 45 at. pct, with less chromium in films of cathodically reduced, active, and open-circuit samples, in that order.

Jan 1, 1979

By Thomas J. Fisher, John J. Sammarco, Gary L. Mowrey, Edward F. Fries

This report (Safety File 3.0) is the fourth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2002

By John J. Sammarco, Edward F. Fries

This report (Independent Functional Safety Assessment 4.0) is the fifth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2003

By Wilbert T. Malenka

In its search for a highly productive mining system for anthracite beds pitching from 100 to 200, where conventional mobile equipment cannot be used) the Bureau initiated a longwall project by introducing a shearer drum cutter loader of European origin. Because of the undulating nature of the roof and floor and changing bed thicknesses, the machine proved inflexible and extra work was required in lifting bottom coal and blasting top coal.

Jan 1, 1966

By W. F. Hughes

The thermodynamics of an electromagnetic field-fluid interaction system is discussed. A review of the thermodynamics of linear media (the permittivity and permeability taken as functions of density and temperature) is presented; then an extension is made to nonlinear media (the permittivity and permeability taken as functions of the fields). Expressions for thermodynamic properties and reversible work are derived and the first law of thermodynamics for magnetohydrodynamic flow is discussed.

Jan 1, 1968

By D. Cummins

This Information Circular presents a brief history of the lead-acid battery and describes ways to prevent serious injury from battery explosions when servicing and charging lead-acid batteries, particularly in the surface mining industry. The Mining Safety and Health Administration (MSHA), U.S. Consumer Product Safety Commission, battery manufacturers, and the mining industry have all contributed information as well as recommendations for injury-free handling for this report.

Jan 1, 1980

By Dennis Dolinar, Christopher Mark, Gregory M. Molinda

In 1999, 2,087 unplanned roof falls were reported from 841 mines. Nearly 55% of all mines reported at least one roof fall, and nearly 17% of the mines reported five or more falls. In order to investigate the variables that contribute to roof falls, the National Institute for Occupational Safety and Health (NIOSH) compiled a national database of roof performance from 37 coal mines. Geotechnical factors and their effect on roof fall rates were compiled from over 1,500 miles of drivage. The factor that is the best predictor of roof fall rate is the Coal Mine Roof Rating (CMRR). For a low CMRR (#30), almost all cases have high roof fall rates. Conversely, high roof fall rates are rare for strong roof rocks (CMRR $ 60). Roof fall rates were also higher in deeper mines, probably because of greater stresses. Intersections were much more likely to fall than roadways, and four-way intersections were more prone to fall than three-way intersections. In a controlled comparison of the effect of increasing bolt length on roof fall rates, it was found that longer bolts reduced the roof fall rates in 11 of 13 cases. A relationship between the roof fall rate, the intersection span, and the CMRR was also found. Finally, a systematic method for tracking roof performance and geotechnical variables was demonstrated.

Jan 10, 2000

Reduce longwall equipment transfer time between panels by utilizing a predriven recovery room, and thus eliminate the premove preparation associated with most equipment recovery methods. Background and Approach The recovery point for a retreating longwall is a predetermined position near the end of the panel where mining is terminated and equipment is disassembled and removed. However, to prepare for equipment removal at the recovery point, bolting and wire meshing arc required before the recovery point is reached. Usually, preparations for equipment recovery begin about 35 ft from the recovery point, significantly impeding the normal rate of advance of the longwall and, consequently, production. Recently, BethEnergy Mines, Inc., and the Bureau of Mines cooperated to evaluate the applicability of utilizing predriven recovery rooms to improve longwall equipment recovery. A predriven recovery room is an entry driven parallel to the longwall face at the end of the panel, having standard dimensions (for that particular mine) and supported with bolts, wire mesh, and supplemental support. The preparation of this entry is completed before it experiences mining-induced effects from the approaching longwall face. This enables the face to continue to mine at its normal rate of advance until the panel is completed. The supplemental support is required to control the loads imposed by the front abutment and is the most vital component of the recovery room.

Jan 1, 1989

Minimize the effects of underground mine conveyor belt fires by developing methods to prevent automatic fire suppression system failures. The Problem Fire protection is achieved by prevention, early detection, and planned fire-fighting response. Automatic fire suppression systems are one form of planned fire-fighting response. When these systems are properly designed, installed, and maintained they can effectively control fires. Conveyor belt fires account for about 20% of underground coal mine fires. Fire protection requirements have been established for underground locations because of potential for start and spread of fire and the restricted personnel egress in a fire situation. Belt conveyor systems arc potentially dangerous because of the high fire incidence rate, high temperatures, dense smoke, toxic gases, and rapid flame-spread rate. While investigating the conveyor fire suppression problem, the Bureau identified automatic fire suppression system reliability as a potentially serious deficiency within the mining industry. Table 1 lists common failure modes fur three Fire suppression system types. This table summarizes findings of Mine Safety and Health Administration electrical inspectors responsible for inspection of belt protection automatic fire suppression systems. Batteries, contact points, control wires, and electric servocontrols are all prone to failure. Figure 1 shows rock-dust-contaminated relay contact points. This condition is dangerous because of the chance of intermittent failures, which might allow systems to pass annual functional testing, yet fail during actual fire emergencies.

Jan 1, 1989

A construction material based on plasticized sulfur and mineral aggregate, that is superior in corrosion resistance and strength to portland cement concrete. The material can be used in the chemical, metallurgical, and fertilizer industries, and will also provide an attractive market for by-product sulfur resulting from compliance with pollution regulations. How It Is Made Sulfur concrete is thermoplastic material. Plasticized sulfur is mixed with sand and gravel aggregate heated to 375-400° F. The sulfur melts and acts as the binder or cement. The sulfur concrete is poured hot and sets at a temperature of 200° F. Full strength is attained in a few hours, compared to several days for portland cement concretes. Sulfur concrete even pours and sets in freezing weather. Although unmodified sulfur with aggregate will produce a sulfur concrete with good initial properties, it undergoes crystallographic modifications, and deteriorates with time, particularly when exposed to moisture or freeze-thaw conditions. The Bureau of Mines has developed plasticizers which, when reacted with the sulfur, give sulfur concretes with excellent moisture and freeze-thaw resistance. The plasticizers are based on mixtures of dicyclopentadlene (DCPD) and ollgomers of cyclopentadiene. About 5 percent by weight of the plasticizers is reacted with molten sui fur for several hours. The sulfur cement can be used directly or allowed to solidify for easier handling and storage.

Jan 1, 1981

By Seth C. Schaefer

The Bureau of Mines investigated thermodynamic properties of Mn304 (manganomanganic oxide) and Mn203 (manganese sesquioxide). The standard Gibbs energies of formation (?Gf°) of Mn304 and Mn203 from their lower oxides were determined with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnO, Mn304//Zr0 2//02(g, 0.0112 atm), Pt, with the overall cell reaction 6Mn0(c) + 02(g, 0.0112 atm) = 2Mn304(c), where- 02 refers to indicated partial pressure of oxygen at the reference electrode. Similar measurements were obtained for the cell Pt, Mn304, Mn203//ZrO2//02(g, 0.0115 atm), Pt, with the overall cell reaction 4Mn304(c) + 02(g, 0.0115 atm) = 6Mn203(c). Equilibrium oxygen pressures for the Mn0-Mn304-02 and Mn304-Mn203-02 systems were measured and may be expressed for the respective systems as [23,400 109 P02 T + 11.91 (764.9 - 1,208.6 K) and log p02 = - 11,957 + 9.66 T (968.6 - 1,208.2 K),] where pressure (p02) is in atmospheres and temperature (T) is in kelvins. Standard thermodynamic properties of Mn304 and Mn203 were derived from these measurements and auxiliary thermodynamic data from the literature.

Jan 1, 1982

By Bruce D. Sartwell

The Bureau of Mines is using characteristic X-rays produced by proton bombardment of a solid surface to provide quantitative compositional analyses of surface layers of metals. An integral X-ray yield equation has been developed that quantitatively relates the measured X-ray yield to the thickness of thin films ranging from less than a monolayer to several thousand angstroms. The use of the integral yield equation is demonstrated for the growth of a thin film by vacuum evaporation. Results are presented that show haw proton-induced X-ray emission (PIXE) has been used to determine the oxidation kinetics of iron that had been implanted with several different species of heavy ions. The sensitivity of PIXE for the measurement of very-thin-film growth kinetics is demonstrated from studies of the effect of fractional mono-layer coverages of sulfur on the initial oxidation kinetics of iron. Results are also presented in which PIXE has been used to study the redistribution of alloying elements in components of a gas turbine that had fractured due to corrosion fatigue. By combining PIXE with low-energy ion sputtering, quantitative composition depth profiles of surface layers are obtained. Examples are presented for the profiling of iron samples implanted with 25-kev nickel ions and for a platinum coating on an Fe-5Cr substrate.

Jan 1, 1980

By Peter J. Clarke

Afghanistan's mineral industry continued to be dominated by the production and export of natural gas, although several mining and related industrial projects, all under the supervision of Soviet technicians, were in the planning stage in 1982. Afghanistan produced minor quantities of barite, cement, coal, fertilizer materials, iron, and lapis lazuli, all for domestic consumption.2 Large-scale projects being investigated were a copper mine and concentrating plant at Ainak, extensive mining of the Hajigak iron ore deposit near Kabul, construction of an oil refinery at Angot, increasing production and processing of natural gas, and implementing an intensive geologic prospecting and exploration program for areas of mineral potential. Afghanistan's gross domestic product (GDP) was estimated at $2.76 billion3 and has remained stagnant for the past several years. Total exports in 1982 were estimated at $700 million, only a marginal increase from the 1981 figure of $694 million. Exports of natural gas to the U.S.S.R. earned $385 million in 1982, representing just over one-half of Afghanistan's total exports. Natural gas revenues were down approximately 11% from the 1981 level, owing primarily to increased antigovernment activity in the northern part of the country.4 About 90% of the country's natural gas production was exported to the U.S.S.R.5 About 38% of Afghanistan's development budget had been earmarked for mining and industrial projects in 1982.6

Jan 1, 1984

By William P. Diamonds, David C. Oyler

Stimulated vertical boreholes are an effective means of removing gas from coalbeds in advance of mining. This Bureau of Mines report examines the coal mine roof damage potential of stimulation treatments. Twenty-two Government-sponsored stimulation treatments have been mined through to determine the effects on the coalbed and roof strata. Vertical fractures in the coalbed were discernible for most treatments and horizontal fractures were present for about half of the stimulations. Sand-propped vertical fractures were usually short in lateral extent. Evidence of stimulation fluid movement could generally be traced beyond the maximum extent of sand-filled fractures when fluorescent paint was added to the treatment fluids. The maximum lateral extent for a sand-filled vertical fracture was 416 ft and a paint-coated vertical fracture extended 630 ft. Horizontal fractures were generally found within bedding planes, most commonly on top of the coalbed. The maximum lateral extent for a horizontal fracture was 265 ft at a coalbed depth of 630 ft. Horizontal fractures have been found to occur as deep as 1,145 ft. Penetration of strata overlying coalbeds was observed in nearly half of the treatments intercepted. Most of these occurrences have been interpreted to be penetrations into preexisting joints. No roof falls or adverse mining conditions were encountered that could be attributed to the stimulations.

Jan 1, 1987

"As stated earlier the primary goal of the Generic Mineral Technology Center for Respirable Dust is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. While initial work was directed to coal dust the charge to the dust center has been expanded to include diesel particulates and asbestosis, the latter of deep concern not just to workers in the mineral sector of the economy but also to the general populace.A major facet of Dust Center research has been the analysis and documentation of comprehensive research protocol and procedures that are appropriate state-of-the-art in the various areas of respirable dust. In addition to definition of standardized research protocols and procedures which would be utilized by center personnel for uniformity and reproducability there is a considerable need for utilizing standardized respirable dusts in experiments with consistent, reproducible characteristics which simulate those of actual mine dust. This respirable dust needs to be available in large quantities for a wide variety of research uses that include animal and medical experiments. The dust must be free of the lubricating oils and grinding wheel contaminants that are frequently encountered in laboratory generated dusts.The holistic approach to establishing standardized protocols and procedures applicable to the five major research areas of the center is presented in Figure 5.In one hypothesis, range in coal volatility is considered to be a major causal factor in the incidence and severity of pneumoconiosis. Therefore a suite of characterized standard respirable dust samples have been prepared for researchers from coals representing the western (high volitile A bituminous), central (medium volatile bituminous) and eastern (anthracite) mining areas of Pennsylvania. Quartz, limestone (rockdust) and kaolin clay samples, representing important mineral constituents of coal dust have also been prepared.A suite of medical investigations have been developed utilizing small and medium size animals as well as non-human primates in a variety of dust/lung interaction projects which will be discussed in the next section. A number of respirable dust sampling and dust generation methods have been investigated and selected techniques utilized for both in-mine and in-laboratory research investigations. These will also be discussed in more detail later. A wide range of respirable dust size, chemical and mineralogical analyses have been investigated, standardized and documented for use in various research investigations.This interaction and documentation of various respirable dust sample procedures, animal and medical tests, sampling and dust generation methods, plus size, chemical and minerological analysis applied in the five major areas of research investigation have served to create a very favorable synergism and rapid technology transfer in the respirable dust center."

Jan 1, 1988

By L. C. IlsLey

The Burrell methane indicator developed by Col. G. A. Burrell in 1915 was modified during 1918 to the " insulated type " Burrell indicator . Though this instrument has been used in mines since its first introduction , it was not formally approved as safe and efficient for use in gaseous mines until March , 1922. The indicator is built by the Mine Safety Appliances Co. , Pittsburgh , Pa . Approval No. 800 has been assigned to this company covering the device in the form approved . The principle of the Burrell indicator is fairly well known . It works on the same principle as the Haldane apparatus - measuring by means of a graduated scale , the contraction resulting from burning the methane content of an air and gas sample . A given aniount of the mine atmosphere to be tested for methane is taken into the indicator . This sample is then thoroughly shaken with the water in the indicator for one minute . The methane in the sample is now burned for two minutes by a heated platinum coil , which is energized by a small storage battery containing two Edison cells connected in series . After the glower or coil has burned for two minutes , it is disconnected from the battery , and the indicator is again shaken for The amount of contraction observed by reading the height the water rises in the U- tube of the indicator , which is calibrated to register the percentage of gas in the sample . The indicator as approved by the Bureau of Mines is equipped with an Edison M- 8 mine- lamp battery , and with a glass and scale graduated from zerɔ tɔ four per cent methane . The approval of a corbination service that is , an attachment for giving illumination from the same battery from which the platinum glower is operated has been withheld pending the development of a battery with larger capacity . - Under laboratory operating conditions , a single glower was capable of making at least 20 determinations if proper precautions were observed with respect to the use of freshly charged batteries . A battery should be allowed to stand off charge several hours before using in an indicator , as the peak voltage of a freshly charged Edison cell is abnormally high and is likely to send enough current through the glower to melt the platinum wire . Fifty-seven satisfactory operations were obtained from a completely charged battery . The point where the voltage of the cell fell below 2.3 volts with the glower attached was taken as the lower limit of successful operation . A voltage less than 2.3 does not permit the lower to burn at a temperature that will completely burn the gas in the air , thus giving a false indication .

Jun 1, 1922

By Peter. PH. D. Cain

Smoky River Coal Ltd. mines low-volatile metallurgical coal by surface and underground methods in the foothills of the Rocky Mountains of Alberta, Canada. Current underground operations are confined to the 5B-4 Mine. Development of 5B-4 began in January 1998; production from depillaring sections commenced in July 1998. This paper describes the history of underground mining on the Smoky River property in terms of extraction methods and pillar design. The development of the present pillar design guidelines is discussed in this context. Recent work to prepare a number of case histories for back-analysis using the Analysis of Retreat Mining Pillar Stability (ARMPS) method is described, along with the modifications developed for calculating the ARMPS stability factor for retreat extraction of thick seams. The design criteria are described, as well as the geotechnical program implemented in order to verify its applicability.

Jan 5, 1999

By G. B. Atkinson

Properties of catalysts prepared from intermetallic compound precursors were investigated by the Bureau of Mines as part of its mission to decrease U.S. dependence on foreign sources for scarce catalytic materials, such as nickel, cobalt, and chromium. Methods were developed whereby catalysts with surface areas of 30 to 40 m2/g were prepared from intermetallic compounds. Activity of these catalysts for the methanation reaction and methanol synthesis was deter-mined using a fixed-bed, single-pass, flow-through reactor. Catalysts prepared from rare-earth-nickel intermetallics had specific activity for methanation that was five times greater than that of commercial catalysts and were equal to or better than commercial catalysts with regard to sulfur tolerance. Under identical reaction conditions, catalysts prepared from thorium-copper intermetallics produced more than 10 times as much methanol as a commercial low-pressure catalyst and exhibited a high degree of catalytic stability.

Jan 1, 1982