Search Documents

By Oliver Bowles

Enormous quantities of limestone are used for metallurgical purposes. Approximately 23 million tons were so used in the United States in 1925 chiefly for smelting iron ores in the blast furnace. Smaller amounts are used in basic open-hearth steel manufacture, and in smelting lead, copper and antimony ores. Most limestone producers lave little knowledge of the way in which their stone is used in metallurgy. Maximum tolerances of silica, alumina, sulphur and possibly magnesium; and minimum content of calcium carbonate may be arbitrarily fixed for the guidance of the producer, but aside from these requirements little information is available to producers on the manner in which their stone is used, the office it performs in smelting, or the effects of impurities. More complete [wledge] of utilization would enable limestone operators to solve their production problems more intelligently.

Jan 1, 1927

By E. L. Burwell

Application of the in situ recovery process to oil shale was tested during two field experiments near Rock Springs, Wyo. The results of these tests demonstrate that a self-sustaining combustion zone can be created in an oil shale body, that this zone can be moved through the oil shale, and that the process will produce shale oil. Evaluation of the combustion process by monitoring produced fluids for physical and chemical properties and volumes is described. The material and energy balance obtained is compared with a second evaluation based on extensive coring of the test area after the test was terminated. Several side results of the research are noted such as ground surface heating by underground burning and production of low-to medium-Btu gas during retorting.

Jan 1, 1973

By L. C. IlsLey

"The maintenance of permissible equipment which is tested and inspected at the Pittsburgh Experiment Station of the United States Bureau of Mines is dependent to a surprisng degree upon the voltage at which the equipment is operated. The difficulty of maintaining 500-volt equipment is frequently brought to the bureau's attention, and it is quite possible that if the bureau had appreciated at the beginning the full hazard involved, it would never have undertaken the approval of equipment operating at voltages greater than 250 volts.In this connection, the following statement from State mine inspection departments and other sources are of interest as showing the general feeling in safety organizations with respect to voltages higher than 250. These statements, although obtained as a result of a questionnaire sent cut several years ago, still apply very well to present conditions.A. I have not had time to consider seriously the proposed change from every angle, but looking at it from a standpoint of hazard, feel that the danger would be greatly increased. I have always occupied the position that underground voltage on portable equipment should never exceed 250 volts.High voltage of course would mean smaller transmission lines, which would be more economical and no doubt would require in several instances smaller equipment; notwithstanding, if this statement is true, the writer is still favorable to low voltage on underground portable equipment.B. I believe 500 volts should be the limit on the best equipment ender the best conditions and that the U. S. Bureau of Mines should do all in its power to limit the voltage to 500 volts on permissible equipment, as any increase in voltage means increased hazard.C. I will refer you to a section of our mining law, entitled ""An Act to Regulate the Tine of Electricity in the Mines of the State of ----"" which reads in part, as follows: Trolley wires, or other exposed electrical wires, shall not carry a voltage above 275 volts.You may readily see by this that we are not permitted to operate mining machines under ground in -----, with more than 275 volts at the terminals, except that we are permitted to install transforming stations throughout the mines, after complying with certain regulations at the mine.However, as we have had to date, within the calendar year of 1925, six men electrocuted in the mines of the State, using a voltage of 275 volts, I am of the opinion that if this voltage was increased, the hazard would also be increased in proportion.D. I do not care to make a statement for publication: however, I am referring you to our mining laws. On page 27 and 28 you will find what the laws of -----¬require relative to the installation of electricity in the mines.""Hereafter where electricity is installed no higher than two hundred seventy-five (275) volts shall be used underground, except for transmission, or for application to transformers or other apparata, where the high-voltage circuit is stationary. High-voltage motors, and transformers, shall be installed in suitable chambers, built of fire-proof construction, and well ventilated, and shall not be placed on intake, or between intake and return air courses. All high-voltage lines lines and apparata must be clearly marked, to indicate their danger. Main and distribution switchboards for high voltage shall be made of insulating and incombustible material, such as marble or slate, and to be free of all metallic veins, or of material equivalent thereto. Same shall be installed in a dry place. All switches or other instruments used in connection with high voltage shall be installed on suitable switchboards, with at least a three-foot passageway in front and rear properly floored, and kept looked by a door at each end that can be opened from the inside without a key. With higher than medium voltage, there shall not be any live metal work on the front of switchboard, and the entry circuit must be protected by an oil breaker s"

Apr 1, 1932

By W. Ayvazoglou

A large number of organizations interested in the search for mineral deposits have adopted the magnetic method of geophysical prospecting, as it has proved to be the most simple, convenient, and rapid, and at the same time the least expensive in comparison with other methods. According to the last statistical data, about two millions square kilo¬ meters were explored in the United States by different geophysical methods. Ninety-six per cent of this area was prospected for oil and 4 per cent for minerals. Detailed exploration by means of the magnetometer has been carried out over about 85 per cent of this surface. The great advantages offered by this method resulted in the fact that the magnetometer was tried out in most places in which geophysical methods were applied. The main purpose of such e:rploration is to obtain the maximum knowledge valuable to the geologist; therefore good geological interpretation of the results of measurements is important. The possibility of drawing practical conclusions from a map representing the results of the study of the terrane depends greatly on the accuracy with which the measurements are made. The purpose of this article is to show the different sources of error by which the work of an operator may be affected and to discuss the means by which the carrying out of a magnetic survey may be improved.

Nov 1, 1931

By G. S. Price

This paper, which describes the milling practice at the Page concentrator of the Federal Mining and Smelting Co., is one of a series being prepared by the Bureau of Mines. The Page mine and mill are located on Silver Creek, 3 miles west of Kellogg, Idaho, and 1 mile south of United States Highway No. 10. Supplies and concentrates are hauled by truck over an automobile road which connects Highway No. 10 with the property. The concentrator has capacity to treat 300 tons of ore per day and utilizes all-flotation methods of treatment. Power is supplied from the main line of the Washington Water Power Co. which runs from Spokane, Wash., to Kellogg, Idaho. Water is obtained from the mine and also from a well which is situated 1 mile distant from the concentrator and about 600 feet in elevation below the concentrator.

Jan 1, 1932

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

By W. H. Young, R. L. Anderson

"Physical conditions, such as thickness and character of the coal seam, dip or pitch of the seam, depth of cover, character of roof and overlying strata, mine water, etc., affect the productivity in bituminous-coal mining. Thickness of the coal seam being mined is probably the most important single item that determines whether the output per man per day shall be low or high; however, in strip mining the depth of cover or overburden to be moved is of equal importance.Bituminous coal is mined today from seams of exceedingly variable thickness - less than 2 feet to more than 50 feet; however, a large majority of the mines are producing .coal from seams 3 to 6 feet thick. The average thickness of the coal seams mined in the United States has not changed materially in the past 25 years. The average seam thickness for all bituminous-coal mines was 63 inches in 1920 4/ and 65 inches in 19)45. As thick seams have been exhausted in the older fields, other thick seams, have been opened in the newer fields.Productivity increased from 4 net tons per man per day in 1920 to 5.78 in 1945. This 45 percent increase in productivity resulted from increased mechanization. The percentage of underground production represented by coal cut by machines increased from 61 in 1920 to 91 in 1945 Mechanical loading increased from less than 1 percent of underground production in 1920 to 56 percent in 1945, and strip mining increased from less than 2 percent to 19 percent of the total production during the same period."

Dec 1, 1947

By Martin J. Gavin

During the recent study of lubricating oils carried on in the San Francisco laboratory of the United States Bureau of Mines, it became desirable to distill the oils used in the experimental work at pressures as low as 10 millimeters (mercury column) absolute. In the effort to Overcome difficulties and eliminate sources of error, certain changes were made in the apparatus for vacuum distillation used by the Bureau of Mines for crude petroleum.4 These changes were described in R.I. 2819, issued in July, 1927. Subsequent to the publication of R.I. 2819 several other changes have been made, and the present form of the apparatus for vacuum distillation of lubricating oils is described in this revision of R.I. 2819. These changes were found to give more accurate checks on duplicate distillations. The major part of the credit for the laboratory work which developed the changes in the apparatus and method revised herein is due to Boyd Guthrie, assistant petroleum chemist, and R. V. Higgins, junior chemist, o the San Francisco laboratory, United States Bureau of Mines. DESCRIPTION OF APPARATUS The distilling flask employed is essentially the Hempel flask as used by the United States Bureau of Mines for the analytical distillation of petroleum.5 he complete apparatus is shown in Figure 1. The fractionating column and exposed portion of the flask is wrapped with 4 inch asbestos rope and then surrounded by a cylindrical hood of 1/8 inch pliable asbestos sheet with a narrow air space between the wrapping and the cylindrical hood. This was found necessary to prevent any radiation or convection heat losses from the column, and resulted in obtaining a more even and constant fractionation by eliminating any dephlegmating action caused by temperature changes around the column.

Jan 1, 1930

By George S. Rice, C. W. Owings

"Brattice cloth is an important material in coal-mine ventilation practically all coal mines use some brattice cloth, gassy mines a large amount. It is employed in three ways:Crosscut brattices.Curtains in haulageways.Line brattices in gassy mines.In each case brattice cloth is used to deflect part or all of a split of the mine ventilating current into or toward the face of a working place. As a general rule, its use in a particular location is temporary.A crosscut brattice should be employed only until a permanent stopping has been erected. Such a brattice is subject to little wear when in actual service, the chief damage occurring when it is taken down and put up again.When used for curtains on haulageways or haulage crosscuts to deflect the air current up into rooms or headings, the wear on brattice cloth is considerable, as mine cars, machines, and personnel constantly pass under the curtains which last only a few days or a few weeks in an active part of the mine. For such purposes tightly woven smooth cloth is desirable, so that it will not be easily torn. Curtains should not be used back from the working places, as they sometimes are, to deflect the main. split, as the leakage of air is too great. Doors should be used in such places."

May 1, 1928

By L. E. Schultze

[The Bureau of Mines conducted bench-scale studies to develop techniques for stripping tetravalent cerium from tri-n-butyl phosphate solutions. Experiments were conducted in a constant-temperature bath using beakers and mechanical stirring. Ninety-five pct of the cerium was stripped from a 50-pct tri-n-butyl phosphate 50-pct kerosene solution containing 0.18 M cerium in 15 minutes at 50° C using 0.11 M aqueous formaldehyde.]

Jan 1, 1974

By d&apos, Kathleen J. Amico

This summary appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1967

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals and investigations of their chemical and physical properties. The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures When placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld. County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937

By B. W. Madsen

A nearly dormant copper sulfide pilot-scale experimental leach containing 8.7 tons of are was injected with oxygen to determine its effect on the copper-leaching rate. Prior treatment of the uncrushed 0.25-percent-copper, mine-run stripping material consisted of 461 days of acid ferric sulfate leaching, which extracted 47 percent of the total copper. The permeability of the bed had decreased, and the percolation rate had decreased from an initial 20 gallons to 0.8 gallon per square foot per day. Copper extraction had nearly stopped. After injecting oxygen into the ore column and leaching for 30 days, the percolation rate was increased to 6 gallons per square foot per day. In an additional 298 days of leaching, an additional 40.7 percent of the copper was extracted. The improved leaching after the use of oxygen is attributed to stimulated bacterial action, better oxidation, and increased permeability.

Jan 1, 1975

By W. H. Ode, W. A. Selvig

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County Colo., in connection with a survey of carbonizing properties of American coals 4/ and investigations of their chemical and physical properties. 5/ The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the as from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

May 1, 1937

By P. S. Lewis

Shortage of natural gas is reviving interest in low-Btu fuel gas made by gasifying coal in fixed-bed producers. The Bureau of Mines gasified strongly caking Pittsburgh bed coal over test periods lasting four days in an experimental gas producer located at Morgantown, W. Va, Mechanical stirring throughout the fuel bed was effective for keeping the fuel moving and this stirring made the operation successful; hence, the gas producer was named the stirred-bed producer. Nuclear density gages were applied as control instruments to indicate coal flow and fuel level, and to record the frequency and location of void spaces in the bed, The gas, of nominal 140 to 165 Btu/scf calorific value, could be burned in a boiler for generating steam.

Jan 1, 1972

By Eugene T. Sheridan

This circular presents data on individual plants of the fuel-briquet and packaged-fuel industries that responded to the Bureau of Mines annual economic survey and reported production for 1959. The companies named herein represent virtually all producers of processed fuels of mineral origin. A few small companies may not have been canvassed or failed to respond, however, as some plants operate intermittently, and the survey is voluntary. No consideration was given to size of the plant and all plants that reported commercial production were included. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, fabricated from fine-sized mineral fuels by mixing with binders and compressing into small individual shapes. Briquets usually are produced as small, pillow-shaped pieces, 2 to 4 inches long, weighing 2 to 4 ounces. Packaged fuel consists of 3- to 4-inch cubes, 6 or 8 of which are wrapped in heavy kraft paper to form a package weighing 10 to 15 pounds. The overall size of a popular package is 10-112 x 7 x 3-1/2 inches. Briquets are durable, may be stored outdoors, and shipped and used as bulk fuel. Packaged fuel is fragile, and must be stored indoors to keep it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times as a supplement to other fuels. Package fuel is burned without removing the paper and referred to as the "white-glove" fuel.

Jan 1, 1960

Spectrochemical methods were developed to determine beryllium in the concentration range 0.0015 to 4.0 percent in siliceous mineral beneficiation products. Two methods are described. They are (1) a fusion-pellet-spark procedure (spark method) and (2) a sustaining alternating-current arc procedure (arc method). In the spark method the sample is fused with lithium tetra-borate and vanadium pentoxide. The resulting bead is crushed, mixed with powdered graphite, and briquetted. This is analyzed spectrographically using controlled high-voltage spark excitation. In the arc method the sample is diluted with germanium metal, graphite, and vanadium pentoxide. Weighed charges are packed into cupped graphite electrodes and subjected to excitation with a sustaining alternating-current arc. Vanadium serves as internal standard for both methods. Effects due to matrix variations in samples and standards are eliminated either by fusion with lithium tetraborate in the spark method or by dilution with germanium and graphite in the arc method. Beryllium determinations show deviations from accepted chemical values of approximately 5 and 8 percent for the spark and arc methods, respectively. Analyses can be made more rapidly by the arc procedure with a sacrifice in precision and accuracy. Either method can be applied to the determination of beryllium in silicate rocks.

Jan 1, 1962

By Lawrence W. Scott

This report presents several systems for continuously monitoring the quality of air in underground mines that are being developed by the Bureau of Mines. Underground stations measure methane, carbon monoxide and nitrogen dioxide concentrations, air velocity, and air temperature. This information is transmitted over a single telephone pair to central stations located on the surface. The central stations display alarms and the data is selectably displayed on digital panel meters.

Jan 1, 1977

By Philip C. Good

The Bureau of Mines investigated the feasibility of utilizing low-grade phosphatic shale as a feed for phosphoric acid production. Present practice in the phosphate mining operations of southeastern Idaho is to remove and either stockpile or waste low-grade phosphatic shales as the high-grade phosphate beds are selectively mined. Acid digestion studies were performed on uncalcined shale and on shale calcined to remove free carbon to determine phosphoric acid quality, yield, and amenability to filtration. The untreated shale, containing 21.4 pct P205, was digested with sulfuric acid in a single-tank reactor to yield phosporic acid and gypsum residue. Although 96 pct P205 recovery was attained in digesting uncalcined shale, only the calcined product gave satisfactory filtration rates. Calcined shale yielded phosphoric acid recovery of about 93 pct of the contained P205. It was higher in impurities than commercially prepared acid derived from high-grade western phosphate rock. An acid filtration rate of 745 lb P205/ft2/day was attained. This value is lower than the rate of 900 lb P205/ft that is generally considered to be acceptable in industrial production of phosphoric acid from high-grade phosphate rock.

Jan 1, 1981

By Edward L. McHugh, Charles Sabine, Louis J. Denes, Jami M. Girard, Peter Metes

The Spokane Research Laboratory, National Institute for Occupational Safety and Health, is investigating various remote sensing technologies as possible tools to detect, monitor, and mitigate hazardous situations in surface mines that could lead to catastrophic slope failure. Promising technologies include a field-portable spectro-polarimetric imager and a stationary interferometric radar device. Field tests were conducted of a prototype visible and near-infrared spectro-polarimetric imager (SPI) built at the Carnegie Mellon Research Institute. The SPI employs anacousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. Images obtained at the Mountain Pass and Castle Mountain mines in southeastern California showed that the instrument is capable of obtaining hyperspectral images of highwalls, outcrops, hand samples and drill core in the field. We have retrieved spectra from Mountain Pass images that closely match those of bastnaesite and have had some success in classifying images. Although radio frequency noise in the data limited spectral classification of imagery, we project that careful alignment of the AOTF should minimize the noise and greatly improve classification.