Search Documents

By V. M. Benson

A simplified, routine method for determining lithium in lithium-bearing rock is presented. The sample is decomposed by repeated treatments with nitric, hydrofluoric, and perchloric acids. Since this procedure does not appreciably dissolve beryl, interference by beryllium (the principal interfering cation) is minimized for most samples. The salts are brought into solution with water and enough citric acid-ammonium citrate buffer is added to make the final volumetric dilution 0.20 M with respect to citrate. The addition of citrate greatly reduces anion interference in the hydrogen-oxygen flame, slightly increases the intensity of the lithium 671 millimicron emission line, and reduces the effect of most of the interfering cations to the extent that analytical separations are not necessary. The accuracy of results of single determinations of lithium in a pegmatite containing spodumene, lithium-bearing mica, and beryl are approximately equal to that obtained by other flame methods, INTRODUCTION This investigation was undertaken in Bureau of Mines laboratories to develop a reliable, rapid, routine analytical method for determining lithium in lithium-bearing minerals. The requirements of the procedure were that the method should be applicable to the analysis of a variety of lithium-bearing ores and test products, and the results would be reasonably accurate for materials containing 0.05 to 8 percent Li20.

Jan 1, 1961

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

By W. L. Schmidt

The effect of a water-repellent film in sandstone cores on the effective permeability-saturation relationship was investigated as part of a cooperative research program between the Bureau of Mines and the American Gas Association. The repellent film was formed by the reaction of methyltrichlorosilane3 with the connate water in the core. Other researchers have reported on the use of silicone chemicals to alter the flow characteristics of porous media (1-3, 5-7, 9, 10).4 The previous studies, however, dealt almost entirely with oil-water or oil-gas systems and not with water-gas systems. The primary purpose of this study was to determine the feasibility of using silane to retard the influx of water into natural-gas storage wells and to determine the necessary requirements for achieving this result. The success or failure of silane treatment as a remedial measure depends on its effect on gas-production rate and attendant water production.

Jan 1, 1961

By Leon E. Esparza

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 16,927-acre Pryor Mountain Wilderness Study Area (MT-067-206), part of the 3,955-acre Burnt Timber Canyon Wilderness Study Area (MT-067-205), and part of the 4,550-acre Big Horn Tack-On Wilderness Study Area (MT-067-207) to evaluate their identified mineral resources. The Burnt Timber and Big Horn Tack-On study areas contain 3,430 and 2,550 acres, respectively. The three areas are in Carbon County, MT, and Big Horn County, WY, about 13 miles north of Lovell, WY. No identified resources exist in any of the study areas. Bureau of Mines personnel reviewed literature, searched county mining records and examined prospects, claims, and mineralized areas to determine whether identified mineral resources existed. The three study areas are within the Pryor Mountain unorganized mining district. U.S. Department of Energy production records indicate there were 223,000 pounds of uranium oxide (U308) and 236,000 pounds of vanadium pentoxide (V205) produced from 19 properties within the mining district. The average ore grade was 0.36 percent [3,600 ppm (parts per million)] U308 and 0.416 percent (4,160 ppm) V20S. Only the Pryor Mountain study area has current claims, the 50 claims of the S0S group.

Jan 1, 1986

By D. E. Shanks

As part of its program to lessen dependence on foreign bauxite as the Nation&apos;s primary source of cell-grade alumina, the Bureau of Mines is investigating sulfuric acid (H2S04) leaching procedures for the recovery of alumina from domestic aluminous materials. The successful application of a H2S04 leaching process depends on the recovery of the aluminum values in an easily washed and filtered form, containing a minimum of water to be driven off in the subsequent calcination step. This goal was met by the high-temperature hydrolysis of simulated aluminum sulfate [A12(S04)3] leach liquor. Crystalline, insoluble aluminum hydroxy sulfate [A1(OH)S04], which had a water-to-alumina mole ratio of 1:1, was produced. Eighty-six percent of a solution containing 127 g of A12(S04)3 per liter and 76 pct of a solution containing 336 g of A12(S04)3 per liter were hydrolyzed to insoluble aluminum hydroxy sulfate by autoclaving for 1 hr at 320° C and rapidly quenching to room temperature. Higher operating temperatures were precluded by corrosion of the autoclave. The yield of aluminum in the hydrolysis product increased with increasing hydrolysis temperature and decreasing A12(S04)3 concentration.

Jan 1, 1981

By G. B. Gait

This report is the fifth in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region. A catalog of the microfilmed maps of 47 of 49 major mines and 18 independent mines in the Southern field is presented. Previous reports included catalogs of microfilmed maps of mines in the Eastern Middle field, the Wyoming and Lackawanna Basins of the Northern field, and the Western Middle anthracite field.

Jan 1, 1978

By Hamid N. Maleki

Cooperative efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, achieved the research objective of showing that data from measurements of the rate and change in rate of mine roof movement can be effective in detecting roof instability. Several instruments and techniques have been used to monitor roof movement and to detect imminent roof caves during pillar robbing. Early detection of unstable conditions can provide time either to withdraw personnel and equipment or to allocate supplemental support to prevent injury or down-time. Critical convergence rates were determined both manually and electronically. The detection of critical rate of movement has been shown to be an effective tool in ground control efforts.

Jan 1, 1988

By R. G. Knickerbocker

[The Electrornetal~.1~~1c~.l T,:tt31~tn~ir of the Bureau of Miner,, 3oulder City, !.Tev. , invsst:&apos;.~:es 1:h .-inc.z-.l ci.c;,oritr, in 51-3 regon around Boulder Dam, i~d. this papei- ?i*esmt; tvr) cl-c~;ef.o!~~ilcinl;$ of n s5siqn of atufiies on boron ninerala GB~O 3;; tlir t ~t;s?,Lo:]

Jan 1, 1940

By Sathit Tandanand

Horizontal displacements and ground strains induced by mine subsidence are significant information needed for calculating damage and developing precautions against subsidence effects on surface structures. To devise a simple method for determining the surface horizonal displacements and strains simultaneously with the subsidence prediction, the U.S. Bureau of Mines examined the significance of the tilt number, which is the proportionality constant in the relationship between the horizontal displacement and the slope of the subsidence profile. The ratio of the tilt number to the critical radius of the subsidence trough is identical to the ratio of the maximum possible horizontal displacement to the full subsidence, which is found to be constant in most European coalfields. If this ratio is known for a particular minesite in the United States, then horizontal displacement and ground strains can be readily obtained from the primary subsidence data.

Jan 1, 2010

By B. J. Scheiner

The Federal Bureau of Mines has successfully demonstrated an electrooxidation-solvent extraction-carbon adsorption process for recovering molybdenum and rhenium from offgrade concentrates. The flow sequence consists of dissolution of metal values by electrooxidation, liquid-solid separation by thickening, acidification and chlorate ion removal by sulfur dioxide treatment, solvent extraction to concentrate the molybdenum and rhenium, separation of molybdenum and rhenium by carbon adsorption, and metal recovery by crystallization. Molybdenum and rhenium were recovered as ammonium paramolybdate and ammonium perrhenate. Electrolysis of brine-concentrate pulps to generate a hypochlorite oxidizing agent in situ resulted in the dissolution of 98.9 and 99.1 pct of the molybdenum and rhenium, respectively, at an energy consumption of 13.7 kwhr/lb of molybdenum extracted.

Jan 1, 1976

By G. V. Sullivan

The Bureau of Mines conducted preliminary beneficiation studies of a gold-bearing graphitic schist from Blue Hill, Tallapoosa County, Ala. The average analysis of the material was 0.08 oz/ton gold. Tabling of minus 35-mesh material recovered 83 to 94 percent of the gold at grades of 6.925 to 2.165 oz/ton, respectively. A combination of jigging and tabling resulted in a concentrate assaying 24.3 oz/ton gold and contained 87 percent of the total gold. Treatment of the material by jigging, tabling, and amalgamation recovered 86.5 percent of the gold.

Jan 1, 1969

By William W. Elmer

This paper, describing the mining method at the Black Butte quicksilver mine, is one of a series of papers being prepared by the U. S. Bureau of Mines on mining practices, methods, and costs in the various districts of the United States. It is presented to show the mining practice and costs in the successful treatment of low-grade quicksilver deposits. The operation discussed is an excellent example of w1-pat can be done in working a limited tonnage of low-grade ore under sound management. The Black Butte mine is situated at Black Butte, Lane County, in the southern part of the State of Oregon, 17-1/2 miles from Cottage Grove -- a station on the Siskiyou branch of the Southern Pacific Co. The Black Butte mining district lies in the foothills of the Calapooia Mountain Range, which connects with the Cascade Range on the east and with the Coast Range on the west. The elevation at &apos;.lie reduction plant is 1,000 feet above sea level. The apex of Black Butte Mountain, or which the mine is situated, has an elevation of 2,700 feet. The district possesses exceptional natural facilities infrequently met with elsewhere for the mining and reduction of cinnabar ores. Several factors which contribute to the unusually low mining costs are:

Jan 1, 1930

By D. C. Dahlin

The Bureau of Mines investigated the Ketchem Dome tin prospect in east-central Alaska to evaluate the tin resource. The studies included field investigations, mineralogical characterization, and concentration of the tin-bearing minerals. The tin mineralization consists of cassiterite (Sn02), which occurs as grains disseminated in a greisen (quartz-mica) matrixo A bulk sample from the largest and best-developed greisen vein exposed at Ketchem Dome contained 0.51 pct Sn. Concentration of the cassiterite by gravity table methods resulted in a product that contained 56 pct of the tin at a grade of 41.4 pct Sn. The mineralization exposed at Ketchem Dome is typical of greisen found in the area and elsewhere in interior Alaska.

Jan 1, 1987

By Natalie A. Sapola, Knox Van Dyke, Jean Rabovsky, Vincent Castranova, William H. Pailes, Melanie McPeek, Deloris J. Judy

"INTRODCJCTJONPlatelet activating factor (PAF) is a glycerophospholipid (1-0-alkyl-2-acctyl-sn-glycerol-3-phosphoryl choline) which has been shown to mediate a broad range of biological activities. 1·3 Its pulmonary actions include contraction of pulmonary tissue,4 secretion of leukotrienes from leukocytcs,5 airway constriction,6 pulmonary edema,7 and enhanced migration of neutrophils into the airspaces of thelungs.8-9PAF can be released from several different cell types, such as, basophils, neutrophils and alveolar macrophages, in response to a variety of particulates or membrane stimulants which include zymosan, calcium ionophore, phorbol esters, chemotactic agents, and endotoxin. 1~1 3 Therefore, PAF may play an important role in the development of pneumoconioses by mediating pulmonary responses of lung cells to a variety of occupational dusts. To investigate this possibility, we determined the effects of P AF on several physiological parameters of neutrophils, alveolar macrophages, and alveolar type Il epithelial cells.METHODSIsolation of CellsNeutrophils were isolated from human blood by dextran settling and centrifugal elutriation.14 Isolated neutrophils (93% pure) were resuspended in HEPES-buffered medium (145 mM NaCl, 5 mM KCI, 10 mM HEPES, 5 mM glucose, and 1 mM CaC12; pH = 7.4). Cell number and volume were determined with an electronic cell counter equipped with a sizing attachment.Rat alveolar macrophages were obtained by pulmonary lavage with ea2+, Mg2+-free Hanks balanced salts solution. 15 Alveolar macrophages (94% pure) were resuspended in HEPES-buffered medium, counted, and sized electronically.Rat alveolar type Il cells were isolated by enzymatic digestion for 35 minutes at 37°C with 40 µ/ml type I elastasc and 0.1 % collagenase and purified by centrifugal elutriation. 16.17 Type Il cells (92 % pure) were resuspended in HEPES-buffered medium for measurement of membrane potential, oxygen consumption, and trypan blue exclusion. Type Il pneumocytcs were resuspended in 0.1 M NaCl plus 0.05 M HEPES (pH = 7.8) to measure cytochrome P450-dependent activities and aggregation. Cell size and number were determined electronically."

Jan 1, 1990

By John Nagy

Results of initial research by the Bureau of Mines are given on the dust explosion hazard of float coal and on the related factors of occurrence, rate of production, sampling techniques, transport, and deposition of float coal. Tentatively, it is suggested that where float coal deposits prevail, a mini-mum of 80 percent incombustible be maintained in the top 1/8-inch layer to neutralize the explosion hazard of the surficial coal deposit.

Jan 1, 1965

By D. J. Judy, D. J. Rabovsky, W. H. Pailes, V. Castranova, K. Van Dyke, J. Rabovsky, N. A. Sapola, M. McPeek

"Platelet activating factor (PAF) can be released from pneumocytes following exposure to occupational dust (Am. Rev. Respir. Dis. 135:83, 1987). In addition, PAF has been shown to induce pulmonary inflammation, edema, and bronchoconstriction (Hosp. Prac. 19, 67, 1983). This investigation reports the effects of PAF on the properties of three types of cells found in the lung. PAF (1-100, K1/2 = 2.5 pH) caused depolarization of neutrophils as well as generation of chemiluminescence and secretion of hydrogen peroxide. These responses were dependent on the presence of extracellular sodium. However, PAF did not alter oxygen consumption of neutrophils. Although PAF (10 uM) caused depolarization of alveolar macrophages, no stimulation of chemiluminestence, superoxide secretion, or oxygen consumption was observed. However, PAF (10 uM). did potentiate chemiluminescence and superoxide secretion in response to zymosan (2 mg/ml) by 55% and 36%, respectively. In addition, PAF (10-90 uM) caused aggregation of alveolar macrophages. PAF (2-10 uM) also caused depolarization of type II cells, but did not affect membrane integrity or oxygen consumption. However, PAF (10-18 PM) enhanced the activities of two distinct forms of cytochrome P-450 in type II cells and caused aggregation of type II cells at PAF doses above 18 uM. These data indicate that PAF can affect the secretory activity of pulmonary phagocytes and the ability• of type II cells to detoxify foreign compounds (Bureau of Mines Grant - G1175142).INTRODUCTIONPlatelet activating factor (PAF) is a glycerophospholipid (1-0-alkyl-2-acetylsn-glycerol-3-phosphoryl choline) which has been shown to Mediate a broad range of biological activities (1-3). Its pulmonary actions include contraction of pulmonary tissue (4), secretion of leukotrienes from leukocytes (5), airway constriction (6), pulmonary edema (7), and enhanced migration of neutrophils into the airspaces of the lungs (8,9).PAF can be released from several different cell types, such as, basophils, neutrophils and alveolar macrophages, in response to a variety of particulates or membrane stimulants which include zymosan, calcium ionophore, phorbol esters, chemotactic agents, and endotoxin (10-13). Therefore, PAP may play an important role in the development of pneumoconioses by mediating pulmonary responses of lung cells to a variety of occupational dusts. To investigate this possibility, we determined the effects of PAF on several physiological parameters of neutrophils, alveolar macrophages, and alveolar type II epithelial cells."

Jan 1, 1988

By P. F. Sands, Michael Sokaski, M. R. Geer

The purpose of this investigation was to determine the advantage of using either a conventional sieve bend ahead of a vibrating screen or of attaching a sieve - bend screen surface onto a vibrating screen to serve as a scalping deck when dewatering or draining dense medium from fine coal . In dewatering , use of either the sieve bend or scalping deck increased the capacity of the vibrating screen tenfold and the recovery of coal finer than 0.5 mm threefold , with no sacrifice in the moisture content of the oversize product . In dense -medium drainage , either the sieve bend or the scalping deck reduced the amount of magnetite retained on the product of the vibrating screen , particularly when the medium was as dense as that characteristic of the underflows from dense - medium cyclones . The sieve bend was slightly superior to the scalping deck in dewatering , but the scalping deck was clearly superior in dense -medium drainage . Additional advantages of the scalping deck are lower cost and a substantial saving in headroom.

Jan 1, 1963

By E. S. Leaver

The mineral value in the ores from the Mother Lode mining districts of California is almost entirely gold, Although many mines have produced extremely high-grade ore the usual mill grade averages approximately $7.00 gold per ton. Fully 80 per cent of the gold has been and is now being recovered by amalgamation. Various methods have been introduced to recover the gold that was not obtained by the amalgamation processes. They include vari¬ous kinds of gravity concentration which in some cases were followed by chlorination or cyanidation. The usual practice includes only stamp battery, plate-amalgamation, and vanner concentration. In the very early practice the tails were run to waste through the main drainage streams of the different mining districts. During later years very large storage dumps have been impounded. These old tails, together with those being saved from present mills, furnish the problem discussed in this article. The clean sand portion of these mill tails is amenable to the usual cyanidation. The slime portion contains the major amount of the gold lost, but it also contains 1-1/2 to 3 per cent carbon, which precludes direct cyanidation of this part of these low-grade waste tails. The black carbonaceous slime portion is the particular problem considered in this report.

Jan 1, 1930

By B. J. Scheiner

Electrooxidation of cinnabar mercury ores (HgS) was investigated as a means of providing an effective and economical hydrometallurgical technique for extraction of mercury from its ores, particularly those too low in grade to allow economical metal recovery by retorting or furnacing techniques. Oxidation was accomplished by electrolysis of ere slurried with brine. Cinnabar was dissolved by oxidation of the insoluble sulfide to soluble mercuric salts. The mercury ion in a brine solution forms a stable tetrachloro complex. Typical laboratory experiments required I to 7 hours of electrolysis at 35-percent pulp density in a brine solution that contained 4 to 20 weight-percent sodium chloride (NaCl). Power consumption ranged from 10 to 50 kwhr/ton of dry ore. Mercury extraction values between 90 and 99 percent were obtained with all of the ores investigated. Subsequent mercury recovery from leach solutions was readily accomplished by precipitation on zinc. Pilot mill experiments in a 100- to 200-lb/hr extraction plant are in progress to quantify power and reagent requirements, and extraction and recovery data obtained to date closely parallel those obtained in the laboratory.

Jan 1, 1970

By R. G. Knickerbocker

[The Electromet l&apos;.ur.::ic&apos;l.l LC:tt:n~ to:!&apos;"&apos; of&apos; the BUl~6au 0: M_nes, Boulder City, ..rev. I invest~.f-&apos;8tes th~ r.: nc= I (l.op itr. in tr.e redon around Boulder Dam, and thi" p2pe:.. ., &apos;est.3nttl t rt") d.c-velo !l&apos;\CtltR of n seriAl of studies on "Joron uineral~ mario n.~ t~l"&apos;t f1tn.: ... o]

Jan 1, 1940