Search Documents

By E. J. Murphy

"INTRODUCTION This investigation is a continuation of previous work 3/4/5/ on the gaseous products of permissible explosives with and without sheaths. The range of oxygen balance of the explosives has been considerably increased. As has been shown previously, certain approximate relations exist between the volumes of gaseous products and the oxygen balance. Further systematization of the data is not feasible, since the method of theoretioal calculatln of the gaseous product is not yet satisfactorily developed. In a previously described method, 6/ it has been assumed that the explosion occurs at constant volume and that thermodynamic equilibrium is established. Apart from the presumably less important uncertainty of some of the thermodynamic data, it is not known how the confinement of the shots in the Bichel gage or the Crawshaw-Jones gage should be treated, or whether thermodynamic equilibrium is fully attained; nor can the extent to which the equilibrium composition changes during the subsequent period of expansion and cooling be judged with any reliability. Therefore, no calculations have been attempted. However, in anticipation of possible future theoretical interest and as an aid in answering practical problems, the new data are presented in the same minute detail as was done previously."

Mar 1, 1948

By D. Montagna

This Bureau of Mines report describes a salt-free, fluxless method for reclaiming metallic aluminum from aluminum dross. The dross is smelted under argon, nitrogen, or carbon dioxide, instead of a salt flux, in an externally heated pot furnace. Aluminum recovery, using argon, is equal to recoveries reported from commercial smelters that process dross in rotary-type furnaces This salt-free method could offer a reduction in air pollution, lower energy requirements by elimination of salts, and the production of up to 60 percent less solid waste for disposal than the salt method.

Jan 1, 1978

By Robert E. Wood

[The temperature dependency of the low-density thermal conductivity coefficients, ?°T, of nitrogen, 100° to 1,200° K, is correlated with the Keyes' equation, ?T ½ -1 -12/T) WT = aT+ bT 10 The equation ?T,P = ?°T +a[ ]ß represented 509 experimental higher V pressure thermal conductivities in the temperature range 131.2° to 973.15° K for pressures to 500 atmospheres, with a mean absolute deviation of 2.35 percent. This equation was used to compute thermal conductivities of gaseous nitrogen for 47 pressures, 1 to 240 atmospheres, and 110 temperatures, 133° to 740° K, which are common to conditions encountered in Bureau of Mines helium purification processes. Isobaric heat capacities, CP, and viscosities, ?T,P, from previous work were combined with the present thermal conductivities, ?T,P, to compute Prandl1 numbers, C?T P / ?T ,P, of nitrogen. Tabular values of Prandtl num¬bers are presented for 49 pressures, 1 to 240 atmospheres, and 75 temperatures, 133° to 740° K. Estimated uncertainties are ±5 percent in the tabulated thermal conductivities and ±15 percent for the computed Prandtl numbers. However, the uncertainty may rise to ±10 percent for thermal conductivities and to ±30 percent for Prandtl numbers as the critical conditions of nitrogen are approached.]

Jan 1, 1971

By Robert F. Randolph, Dana C. Reinke, Richard L. Unger

Purpose The NIOSH Hearing Loss Simulator is a software training and communication tool for promoting hearing loss prevention. It allows a user or trainer to demonstrate the effects of noise exposure on hearing without experiencing an actual noise-induced hearing loss. Estimates of the effects of different levels of noise exposure are based on the American National Standard Determination of Occupational Noise Exposure and Estimation of Noise-Induced Hearing Impairment, otherwise known as ANSI S3.44. This standard specifies the predicted hearing loss for noise-exposed populations of individuals based on risk factors that include gender, age, sound levels (in A-weighted decibels or dBA), and years of exposure. Algorithms specified in the standard were derived from empirical studies of populations that had no exposure to loud noise and other populations that had experienced various levels and durations of noise exposure. This manual explains the major objectives that can be addressed with the simulator and training scenarios that can be applied to real-life, real-worker scenarios. The majority of this guide explains the simulator's functions in detail. Simulator users are encouraged to read this manual while learning how to run the software. [ ] Training Objectives The main objective of the Hearing Loss Simulator is to increase motivation for taking effective hearing prevention action by demonstrating simulated noise-induced hearing losses. [The Simulator can also help teach the following facts about hearing loss. Hearing loss is affected by noise levels. Hearing loss worsens as the noise exposure duration increases. Hearing loss can become permanent. Hearing loss makes it harder to hear what others say. Most hearing loss is not caused by age. Speech is made up of both low and high pitch sounds. Hearing loss due to noise makes it harder to hear high pitch sounds. Hearing loss due to noise has less of an effect on hearing low pitch sounds.]

Jan 3, 2008

By John F. Papp

The Bureau of Mines has sampled microstructure of low-pressure flat flames by mass spectrometer for normal methane-oxygen-argon and for methane-oxygen-argon-bromotrifluoromethane flames. The physical and chemical phenomena, and the method of analysis of mole fraction data to evaluate net reaction rates are here considered in detail. Included is a computer program listing with output on one flame. Chemical species considered are CH4 , CO, CO2, H, H20, OH, Ar, H2, O2 , O, H2CO, CH3 , CF3Br, HF, HBr, Br, CH3Br, HCO, F2CO, CH2 CF2 , H02.

Jan 1, 1975

By D. A. Paice, A. B. Shimp

A test program was conducted to determine the adequacy of molded case circuit breakers for dc electrical systems in coal mines. Mine electrical system parameters and the most severe operating conditions to be expected were determined. Tests of the interrupting capabilities of several molded case breakers were made under the worst conditions to be expected. Continuous and pulsed current carrying capability of the breakers was also investigated. Breakers from two different manufacturers passed all tests successfully. Based on the results of these tests, a set of guidelines for applying molded case breakers to dc systems has been prepared.

Jan 1, 1975

By THOMAS SOULE, R. I. C. Manning

The Phelps Dodge Corporation considers safety a major operating problem , both from the humanitarian standpoint , for this company has a real interest in the welfare of its employees , and from the economic standpoint , for it has found the safe way to be the most economical . In turn , a feeling among employees that the company really has their interests at heart has a wonderful psychological effect . It is bound to bring forth more and better work and to attract and keep workmen of the better class . There is keen competition between the various branches of this corporation for a trophy that is awarded each year to the one having the best accident record . This trophy was won by the Nacożari branch of the Moctezuma Copper Co. in Mexico in 1926 and 1927 , and the Morenci branch won the trophy in 1928 and 1929 .

Oct 1, 1930

By Thomas L. Chapman

The San Manuel is a deposit of low-grade disseminated copper ore. It was brought to the attention of the government in October 1942 through an application to the Reconstruction Finance Corporation for a development loan, supported by a report by Henry W. Nichols. Nichols' sampling of two outcrops containing copper silicate and his geologic map indicated that a minable body of copper ore might be developed. The Federal Geological Survey was requested to examine the property. The Survey mapped the geology in March 1943 and cut a few check samples, which substantially confirmed Nichols' sampling of the outcrops and a few shallow workings. The geologists of the Survey recommended some test drilling by the Bureau of Mines. The property was examined by the author and Wm. D. Hughes, associate engineer of the Bureau of Mines on March 22 and 26, 1943, and a preliminary drilling campaign was recommended. Five shallow churn-drill holes totaling 1,480 feet were put down under the supervision of Chas. A. Kumke, one of the Bureau's engineers, from November 23, 1943, to January 13, 1944. This work indicated that the deposit extended deeper than the 350-foot depth attained in the deepest hole and might have very considerable areal extent. Additional funds were allotted, and the drilling contract was extended twice to a final maximum of 17,000 feet with 2,000 feet maximum depth of hole. Drilling was continued by the Bureau of Mines until February 2, 1945, when 15,844 feet of hole had been drilled. The Magna Copper Co. took options on this and adjoining property in September 1944 and commenced drilling with two machines. It also engaged the two contract drills used by the Bureau after it stopped drilling. It exercised its options in August 1945 and organized the San Manuel Copper Corp. to operate the property. That company is continuing to explore the ore body with six churn drills. Thomas Lyon took options early in 1945 on holdings adjoining the San Manuel property on the east and is operating two churn drills. Exploration up to the completion of the last holes started by the Bureau of Mines indicated a block of ore 3,100 feet long, 400 to 800 feet wide, and 500 to 900 feet thick, and averaging about 0.8 percent copper. Subsequent drilling showed that the ore body extends considerably beyond this block. The axis of the ore body strikes about N. 61° E. Copper minerals are disseminated in hydrothermally altered quartz monzonite and monzonite porphyry. Ore outcrops in two small areas over the northeast part of the block. Elsewhere the copper-bearing rocks are capped by Gila conglomerate, which thickens toward the west and south. Drilling showed that the ore is in a thick, tabular body with a steep dip to the south. The ore body lies near the surface in the northeastern part of the block. The south side of the block is much farther below the surface than the north side. There the upper part of the copper-bearing rocks is lightly mineralized, so that the hanging wall of minable ore lies deeper than the base of the conglomerate cap, which thickens southward.

Aug 1, 1947

By Thoms L. Chapman

The San Manuel is a deposit of low-grade disseminated copper ore. It was brought to the attention of the government in October 1942 through an application to the Reconstruction Finance Corporation for a development loan, supported by a report by Henry W. Nichols. Nichols’ sampling of two outcrops containing copper silicate and his geologic map indicated that a minable body of copper ore might be developed. The Federal Geological Survey was requested to examine the property. The Survey mapped the geology in March 1943 and cut a few check samples, which substantially confirmed Nichols’ sampling of the outcrops and a few shallow workings. The geologists of the Survey recommended some test drilling by the Bureau of Mines. The property was examined by the author and W. D. Hughes, associate engineer of the Bureau of Mines on March 22 and 26, 1943, and a preliminary drilling campaign was recommended. Five shallow churn-drill holes totaling 1,480 feet were put down under the supervision of Chas. A. Kumke, one of the Bureau’s engineers, from November 23, 1943 to January 15, 1944. This work indicated that the deposit extended deeper than the 350-foot depth attained in the deepest hole and might have very considerable areal extent. Additional funds were allotted, and the drilling contract was extended twice to a final maximum of 17,000 feet with 2,000 foot maximum depth of hole. Drilling was continued by the Bureau of Mines until February 2, 1945, when 15,844 feet of hole had been drilled. The Magma Copper Co. took options on this and adjoining property in September 1944 and commenced drilling with two machines. It also engaged the two contract drills used by the Bureau after it stopped drilling. It exercised its options in August 1945 and organized the San Manuel Copper Corp. to operate the property. That company is continuing to explore the ore body with six churn drills. Thomas Lyon took options early in 1945 on holdings adjoining the San Manuel property on the east and is operating two churn drills. Exploration up to the completion of the last holes started by the Bureau of Mines indicated a block of ore 5,100 feet long, 400 to 800 feet wide, and 500 to 900 feet thick, and averaging about 0.8 percent copper. Subsequent drilling showed that the ore body extends considerably beyond this block. The axis of the ore body strikes about N. 61º E. Copper minerals are disseminated in hydrothermally altered quartz monzonite and monzonite porphyry. Ore outcrops in two small areas over the northeast part of the block. Elsewhere the copper-bearing rocks are capped by Gila conglomerate, which thickens toward the west and south. Drilling showed that the ore is in a thick, tabular body with a steep dip to the south. The ore body lies near the surface in the northeastern part of the block. The south side of the block is much farther below the surface than the north side. There the upper part of the copper-bearing rocks is lightly mineralized, so that the hanging wall of minable ore lies deeper than the base of the conglomerate cap, which thickens southward.

Aug 1, 1947

By James S. Browning

Research by the Bureau of Mines demonstrated that organic heavy liquid adhering to or adsorbed on fine mineral particles can be effectively removed by a novel method embracing pulping or displacement washing with hot water alone or in combination with a detergent. Displacement washing with steam alone or in combination with a detergent also was effective for removing the heavy liquid. In tests of sized minus 48-plus 200-mesh mineral charges, both the hot water washing with detergents and detergent steaming effectively reduced the heavy liquid losses on the particles to about 0.2 pound per ton of mineral or less. Centrifuging of the wash solutions permitted an almost complete recovery of heavy liquid from the solution as a pure heavy liquid product.

Jan 1, 1966

By H. E. Perlee

Mathematical expressions are derived for the histories of the pressure, flame radius, mass fraction burned, and burned and unburned gas temperatures associated with a spherical flame propagating concentrically in a spherical vessel. The equations are solved numerically for a 9.5 pct CH4/air mixture using the best available information for the burning velocity, expansion ratio, and specific heat ratio. Calculated histories are in complete accord with experimental measurements. The accuracy of calculated histories is determined relative to errors in the system parameters, and it is found that 10 pct errors in either the burning velocity or the expansion ratio results in a 40-pct error in the pressure history. A 10-pct error in either burned or unburned specific heat ratio results in a 22-pct error &apos;in the pressure history. It was further established that the usual assumption of constant specific heat ratio is unacceptable, but equating the burned and unburned specific heat ratios result in no apparent error in the histories. The cubic law (P = Kt3 + Po) is derived and discussed, and it is found that the law is valid only during the early period (P<2 atm) of flame growth.

Jan 1, 1974

By R. V. Ramani, J. Qin, R. A. Jankowski

"Longwall mining is generally recognized as safer, more productive and economic when compared to room and pillar underground coal mining. There has been, however, increasing concern for the control of airborne coal dust concentrations in long wall faces. The airborne dust cloud at a longwall face is a complex aerosol system containing particles of varied size, density, shape and state of aggregation. For the development of more effective dust control practices in longwall faces, it is necessary to understand more clearly the characteristics of the longwall dust cloud.In this paper, results of a research study on dust concentration distributions along longwall faces are presented. The objective of this study is to characterize the longwall dust cloud behaviour and provide necessary fundamental data for a better understanding of the longwall dust problem. MSA personal samplers and gravimetric total dust samplers were employed to collect respirable and total airborne dust samples. The size distribution of these samples was determined by MicroTrac SPA. The instantaneous respirable airborne dust concentrations were recorded using RAM-I. The dust concentrations are related to face operations, particularly the shearer location and activities. The size distribution of airborne dust, instantaneous respirable airborne dust concentration, and air quantity distributions along longw all faces reveal a complex dust flow phenomenon. Additional fundamental studies are needed for characterizing the temporal and spatial behaviour of the dust cloud at longwall faces.IntroductionModern mechanized longwall mining was introduced in the United States in the 1960's and has become more common in the last twenty years. United States longwalls are multiple-entry retreating faces. According to a recent survey, 91 of the 102 longwall faces employ double-drum shearers (1). Several recently installed longwall faces have consistently produced over 4 000 to 5 000 tons per shift over extended periods of operation. The trend in under-ground coal mining in the U.S. certainly is toward the introduction of longwalls. This trend is true not only for new mines but also for renovation of existing mines. While longwall mining has many advantages over other mining methods, including improved safety, such as higher pro-duction. greater productivity and enhanced reserve recov-ery, it is associated with severe problems of dust control. The increase in longwall production has been accompanied by an increase in respirable dust problems which limit realizing the full potential of the longwall mining system. Despite the efforts to develop improved equipment and operational procedures to control the dust levels at longwall faces, it is still difficult to bring several double-drum shearer operations into compliance with the Federal stand¬ards of 2,0 mg/m 3 respirable dust without loss of produc¬tion. In fiscal year 1987, fifty-eight of the longwall sections were found to be in non-compliance once, and an additional 31 were cited two or more times'''. If the full potential of the longwall mining method is to be realized, new measures must be implemented to control the dust concentration to mandated levels. There is a need for detailed and extensive sampling of longwall faces to understand the dust source-sink relationships and the transient ambient concentrations. These must be related to the mining activities on the face. This paper is to characterize the longwall dust cloud behavior through a series of experiments in operating faces and provide necessary fundamental data for further studies to develop improved dust control practices."

Mar 1, 1992

By R. E. Cerullo

Many computer programs have been written which are capable of performing a least squares fit, both linear and nonlinear, to data gathered by the petroleum researcher. However, when the petroleum engineer tries to program methods of analysis he has used manually in the past, such as forecasting production by decline-curve analysis, more than a knowledge of the use of existing least squares programs becomes necessary. It is the intent of the authors to report the techniques used in the development of such a decline-curve program.

Jan 1, 1970

By Larry A. Haas

The Bureau of Mines constructed a torsion effusion apparatus to measure the equilibrium vapor pressure of pure metals, alloys, and compounds at temperatures up to 1,500° K. The reliability of the apparatus was established by determining the vapor pressure of silver. The data obtained on solid and liquid silver in the temperature range 1,200° to 1,500° K can be expressed by the following equations:

Jan 1, 1965

By Carl Belser

Approximately 30 million pounds of tungsten trioxide in the form of ferberite concentrates have been shipped from Boulder County. Since 1940, the production has varied considerably, being affected by the emergency needs of World War II and the Korean conflict. During World War II, attempts to stimulate production were made by the Metals Reserve Company by stabilizing the price for a specified period, the Reconstruction Finance Corporation by small mining development loans, and the Bureau of Mines and the Geological Survey, who cooperatively explored some of the district by surface and underground core drilling. During the Korean conflict and continuing through the first half of 1954) tungsten production was being stimulated by a Government-gauranteed price and by financial assistance loans under the Defense Production Act of 1950 to qualified operators of properties that have merited exploration. This combined program has increased production in Boulder County from about 1,900 pounds in 1949 to an estimated 383,000 pounds of tungsten trioxide in 1953. The 1953 production came from 67 properties. One of the problems confronting producers is the need for improved beneficiaton methods. Ores from the area have not been amenable to flotation concentration and gravity methods have resulted in poor recovery, often less than 70 percent.

Jan 1, 1955

By Ted C. Briggs

Twenty-two compressibility runs were made with helium over the temperature range -5° to 80° C and at pressures to 800 atmospheres. A Burnett apparatus was used. Data from the runs were fitted to a fourth degree polynomial equation of state in the pressure and a weighting factor of Pr-3/4 was used. All data for a particular isotherm were treated simultaneously. A temperature function was found to represent the parameters B and C. Compressibility factors determined by this investigation are believed to be accurate to better than 0.05 percent.

Jan 1, 1970

By M. M. Fine

This report presents the results of laboratory mineral-dressing investigations by the Bureau of Mines of 14 individual or composite character samples from deposits in the Batesville manganese district. It will be noted that some concentrates have met or approached analytical specifications for metallurgical manganese ore although great variations in both physical and chemical composition from once deposit to another make each a new problem. In most cases it is evident that a substantial loss of manganese has occurred in the various slime and tailing products. An important aspect of this work is the research being conducted on manganese-bearing limestones. Recent reconnaissance indicates that this resource constitutes one of the major domestic reserves of manganese. Laboratory study has shown that ferrograde concentrates can be recovered from samples of manganese-bearing limestones from two properties. Research on samples from other areas is still underway.

Jan 1, 1957

By W. L. Eaton

This report is the second in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Wyoming Basin of the Northern anthracite field is presented. The first report I.C. 8274, published in 1965, was a catalog of microfilmed maps of mines in the Eastern Middle anthracite field. Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1968

By R. S. James, E. J. Gleim

Not long after electrically driven equipment was introduced into coal mines it became apparent that the spark-producing parts, such as controllers and motors, required safeguards to prevent the ignition of mine gas that might come into their vicinity. Many of the early designs attempted to provide protective enclosures having ventila¬tion and relief for pressures if ignition should occur within. The principal feature of the Davy safety lamp, namely, the wire gauze, was employed widely for this purpose. Other devices were developed to reduce the temperature of products of combustion escaping through the protected openings to a value below that which would cause ignition of surrounding explosive atmospheres. Although many such devices performed their intended function satisfactorily under laboratory conditions they were not so satisfac¬tory when subjected to the rigorous conditions encountered under¬ground. Corrosion, mishandling, and accumulations of grease and dirt reduced or destroyed their protective qualities after a period of service in the mines. In the United States this has led to abandon¬ment of special devices in favor of what is called " total enclosure " which means that no regular provision is made for ventilation and release of pressure but rather that the housings or enclosures are built strong enough to withstand the explosion pressures without rupture. As a further protection the joints usually are made of broad, closely fitting surfaces. It is impractical to make such joints absolutely gastight in ordinary machine practice when provision must be made for partial or complete disassembly to facilitate ad¬justments and repairs. Therefore, when an explosion occurs within such enclosures flames may escape through the joints. If the latter are broad enough and not separated too widely, however, the flames will be cooled by contact with the metal surfaces (flanges) of the joints, by rapid expansion, or by both cooling and expansion, with the result that an explosive atmosphere surrounding the enclosure will not be ignited. This is termed " flange protection." In testing parts of cutting machines and other equipment for coal mines, with the ultimate object of approving the equipment for use

Jan 1, 1935

By K. O. Bennington

[Thermodynamic properties of two amphibole asbestos minerals were determined by the Bureau of Mines. The enthalpies of formation were determined by the hydrofluoric acid solution calorimetry method. Heat capacity measurements were made with an adiabatic calorimeter over the range of 5 to 315 K. High-temperature enthalpies above 298 K were determined with a copper-block drop calorimeter to 852 K for amosite and to 902 K for crocidolite. Thermodynamic data determined for amosite of the composition Fe5+2.2766Mg1.5209 Fe+03.12Mn0.0825) Si7.9163Al0.0837022.0363)(OH)1.9637 are: S°298 = 168.8 ± 5 cal/deg-mole; ?Hf°298-15 (elements) = -2419.24 ± 2.95 kcal/mole; ?Hf298.15 (oxides) = -30.92 ± 2.47 kcal/mole; and ?Gf° -2260.1 kcal. Corresponding data found for s3 ,1s = crocidolite of the composition (Na1.9Ca0.1)(Fe2+.024Fe2.5 01Mg0.475) (Si7.9713024Fe+2 2.501Mg0.475) (Si7.971 Al0.029022.095) (OH)1.905 are: S2.98-15 - 161.1 ± 4 cal/deg-mole; ?Rf° 2 298.15 (elements) = -2433.56 ± 2.99 kcal/mole, 10298.1s (oxides) = -87.69 1.70 kcal/mole, and ?Gf°298.15 = -2269.8 kcal.] Calorimetric values from this investigation were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and the constituent oxides.

Jan 1, 1978