Search Documents

By Jennifer S. Riefenberg

The U.S. Bureau of Mines conducts basic and applied research related to predicting, eliminating, and/or controlling rock bursts in underground hard-rock mines and coal bumps in underground coal mines. An important element in this research is the development of a reliable and efficient microseismic source location technique. This report presents the results of a Bureau study to develop and evaluate a new algorithm to locate microseismic events based on the Simplex method, a powerful linear programming technique. The technique was tested on both field data and simulated data. Microseismic event source locations obtained with this new Simplex-based algorithm were shown to have less error than those locations obtained using a least squares method. It was concluded that the Simplex approach to source location of microseismic events can be used effectively in microseismic monitoring.

Jan 1, 1989

By Charles Vaught, Richard S. Fowkes, Ronald S. Conti, Barbara Fotta, William J. Wiehagen

The purpose of this study was to determine mine workers' state of fire-fighting preparedness and the technology being used to detect and respond to underground coal mine fires. To investigate this problem, 214 underground coal miners were interviewed by U.S. Bureau of Mines researchers. Frequency distributions of workers ' responses are presented in this report, along with segments of narrative accounts, to profile miners' fire-fighting capabilities. The data indicated that much variability exists from mine to mine and that there are several important changes operators may undertake in order to make miners better prepared to deal with fire underground: select appropriate sensors, establish and test a warning and communication protocol, construct a system capable of delivering hundreds of gallons of water per minute for sustained periods, institute formal fire preparedness audits, develop case studies of events that occur at an operation to use as teaching and assessment tools, and provide structured practice that can be incorporated into fire drills.

Jan 1, 1995

This publication summarizes, for potential contractors and other interested parties, the proposed research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1977 (October 1, 1976-September 30, 1977) under its Advancing Coal Mining Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the overall goal of providing the system technology required to increase the productivity of the coal mining process.

Jan 1, 1977

By John W. Walkiewicz

The U.S. Bureau of Mines has conducted studies to utilize rapid microwave heating to stress fracture ore samples. Iron ores containing hematite, magnetite, and goethite were subjected to microwave energy in batch operations at 3 kW and heated to average maximum temperatures between 840 and 940 °C. Standard Bond grindability tests showed that microwave heating reduced the work index of iron ores by 10 to 24 pct. In a microwave chamber designed to simulate a continuous throughput operation at 3 kW, the grindability of a taconite ore was improved by 13 pct at a bulk temperature of 197 °C. Because stress cracking occurred at a lower temperature, less energy was consumed. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous, belt-fed applicator. A significant improvement of grindability was obtained with a larger rod mill feed size in comparison to a minus 6-mesh Bond feed.

Jan 1, 2010

By W. J. Long

As a part of the strategic mineral exploration program, examining engineers of the Bureau of Mines collected samples of ore from four manganese properties in Yavapai, Yuma, Maricopa, and Mohave Counties, Ariz. As all of the ores were too low in grade to be acceptable by manufacturers of ferromanganese beneficiation studies were made to determine the amenability of the ores to concentration.

Jan 1, 1948

By D. A. Buckingham

The Bureau of Mines evaluated potential availability of domestic nickel from 23 deposits, Evaluations included an estimation of in situ and recoverable resources, applicable mining and processing technologies, and capital and operating costs. Discounted cash flow analysis with a 15-pct rate of return was used to determine the average total cost of production of each operation, Identified in situ resources contain 9.0 million metric tons (t) of nickel; 5.5 million t is recoverable as nickel metal or ferronickel. Demonstrated in situ resources contain 8.2 million t of nickel; 4.8 million t is recoverable as nickel metal or ferronickel. No nickel is available at a total cost of production equal to the January 1983 market price of $3.24 per pound. Analyses indicate that potential annual production can only meet current consumption levels at a total cost of production of $7.60 per pound of nickel, Nickel's availability is contingent on (1) successful adaptability of nickel processing methods to domestic resources, (2) location of a smelting facility, and (3) marketability of byproducts and coproducts. Analyses were performed on the effects of byproduct and coproduct revenues, energy, labor, and transportation costs, and metallurgical recoveries on nickel's availability.

Jan 1, 1984

By Oliver Bowles

The wire saw, introduced by the Bureau of Mines about two years ago, has revolutionized slate quarrying in Pennsylvania. The success of the saw since its early accomplishments has become greater and greater as the equipment has been perfected and skill acquired .in its use. In the first test made, a cutting rate of 9.7 square feet per hour was attained; in the next four cuts, made early in 1927, the average rate of cutting was increased to 12.8 square feet per hour; in 1928 a maximum of 34 square feet per hour had been attained, with a general average of about 20 to 25 square feet, The wire saw is now regarded as essential equipment in practically all of the quarries in the Bangor, Pen Argyl, and Windgap districts. The wire saw consists of a three-strand steel cable of 3/16 or 1/4 inch diameter running as an endless belt. The driving pulley is a 40-inch double-groove cast-iron sheave. A tension pulley supported by a frame mounted on wheels may travel back and forth on a short track. A weight of 800 to 2,000 pounds gives the desired tension on the wire. The driving units consist of electric motors with direct-drive compactly enclosed gear reduction, or double-belt speed-reduction units; the former is preferred. Silent chain and. pinion gear reductions are used to a limited extent. The travelling speed of the wire is about 15 feet per second. The driving and tension equipment are shown in Figure 1, A.

Jan 1, 1929

By George T. Faust

The petrographic microscope plays an important role in the mineral dressing of nonmetallic materials. Petrographers and mineral technologists have evinced an interest in the technique developed, specifically, for mineral-dressing problems. The following dissertation makes the informa¬tion more generally available. ACKNOWLEDGMENTS The authors are indebted to O. C. Ralston, chief engineer, Nonmetals Division, and to Will H. Coghill, supervising engineer of the Southern Experiment Station for a critical reading of the manuscript. They are also indebted to their colleagues for technical information obtained in the course of cooperative work, in particular to J. B. Clemmer for the use of the data on fluorite.

Jan 1, 1940

By Thomas M. Barczak

Wood cribs are used extensively by the mining industry to stabilize mine openings. While the cost per crib is relatively low, their extensive use can result in annual mine costs of over $1 million. In an effort to improve the utilization of these supports and to reduce ground control hazards, the U.S. Bureau of Mines has developed engineering methods to assist mine operators in wood-crib design and employment. Design and employment criteria are established based on the strength, stiffness, and stability of the crib structure in relation to the load conditions imposed by the mine environment. Models have been developed based on full-scale tests in the USBM's Mine Roof Simulator that compute the capacity of wood cribs of various configurations and material constructions as a function of displacement of the crib structure due to roof-and-floor convergence. These models permit the comparison of the loading characteristics and costs of employment of different crib designs, and in conjunction with roof behavior models, provide a means to determine the optimum design and employment strategy.

Jan 1, 1993

By G. A. Smyres

The Bureau of Mines investigated a HCI-02 leaching procedure to recover Cu, Ni, and Co from a low-grade bulk sulfide flotation concentrate prepared from the Duluth gabbro complex. Since the Duluth gabbro complex is the largest known and unexploited Ni resource in the United States, the development of options for extracting the metal values from the flotation concentrate of this domestic resource is necessary. Conditions were determined for producing a pregnant solution low in Fe to facilitate recovery of the metal values. Leaching experiments were conducted at 15 pct solids, 1000 to 1200 C, 0.2 to 0.3 g HCI per gram concentrate in a 50-gal reactor pressurized to 50 pSig with 02. Base metal extractions from the concentrate were, in percent, 90 to 92 Cu, 99 Ni, 97 to 99 Co, and 0.1 .Fe. Precious metals extractions were erratic and unpredictable; at best their extractions were, in percent, 55 Au, 90 Ag, 40 Pt, and 45 Pd. The reaction time at 1200 C was 0.5 h. The use of compressed air instead of 02 as the oxidant was also investigated. Solvent extraction using LIX 622 was used to remove Cu from the pregnant solution. Cementation on Cu was tested for precious metals recovery, while sulfide precipitation was used to produce a Ni-Co product. A conceptual flowsheet for treating the Duluth gabbro concentrate is proposed.

Jan 1, 1985

By Doerner H. A.

From thermodynamic calculations Maier predicted that zinc oxide and methane would react at specified temperatures substantially according to equation (1). (1.) ZnO + CH4 = Zn (gas) + CO + 2H2. Other reactions that may take place are (2.) CH4 = C + 2H2. (3.) ZnO + CO = Zn (gas) + CO2. (4.) ZnO + H2 = Zn (gas) + H2O. Maier predicted that 870°C would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C. Theoretical considerations indicate that reaction (1) is reversible: this is supported, but not proved, by experimental data. The other reactions are known to be reversible. At low temperatures reaction (2) requires a catalyst and it is slow below 1000°C. Reactions (3) and (4) are rapid, but the equilibrium constants are such that only small concentrations of CO2 or H2O can be produced below 1000°C. Maier calculated that CO2 should not exceed 0.5 per cent at 870°C., and the calculation for water vapor gives a still smaller order of magnitude.

Jan 1, 1931

By W. W. Graff

This paper describing the mining practices at Mine, No. 4 on the Marquette range, Michigan, is one of a series of articles on mining methods and practices in various mining districts in the United States. Mire No. 4 is located in the Swanzy district, in the southern end of the Marquette range, about 3 miles from Gwinn, Mich. The Swanzy district is an isolated ore-bearing formation, and Mine No. 4 is at the extreme southeastern end.

Jan 1, 1930

In the U.S. coal mining industry, a large cohort of miners is at or nearing retirement age. As these miners retire, there will be a need to hire and train thousands of new and most likely younger workers. Moreover, a large portion of safety trainers will also require replacement due to retirement. In a speech before the U.S. House of Representatives (2004), Bruce Watzman, Vice President for Safety, Health and Human Resources for the National Mining Association said, “[W]e will need to replace a major portion, approximately 50%, of the underground coal mining workforce within the next 5–7 years.” The large influx of new mine workers, along with the deficit in safety trainers, creates the challenge to provide consistent and effective safety training. Given the expected high turnover of the mining workforce, it is very likely that incoming workers will have much less experience than those leaving the workforce. Unfortunately, inexperienced miners have been shown to incur the highest rate of injuries. The piece of machinery most associated with these injuries is the roof bolting machine, which accounts for 56% of machinery-related injuries in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) has released a new report entitled “Roof Bolting Machine Operators Skills Training for a Walk-Thru Roof Bolter: Trainer’s Guide” (IC 9489). It is designed to help safety trainers develop struc-tured training for new operators of walk-thru bolting machines. This resource will help trainees learn, understand, and apply knowledge and skills. Included in the trainer’s guide are the following tools: [ ] a six-part DVD video series, a skills check survey, talking points, and a complete job training analysis. Also included is an exercise to help trainees learn more about their mine’s roof control plan, as well as a list of supplemental training and reading materials. On-site trainers can modify this guide to fit their particular mine conditions, machines and equipment, and work procedures. The goal of every coal mine safety professional is to increase safety awareness and make mines a safer place to work. The Walk-Thru Bolting Machine Trainer’s Guide will help teach new miners skills to create a safer working environment that will ultimately prevent or reduce on-the-job injuries. Safety trainers can also use the ideas and concepts from this guide to develop their own training skills for the safe operation of other pieces of underground coal mining equipment.

Jan 6, 2007

By William G. Pariseau

Elastic-plastic finite-element simulation of cut-and-fill stoping in deep, narrow veins shows substantial quantitative agreement with field measurements of stope closure and fill pressure made at two mines in the Coeur d'Alene mining district of northern Idaho. The simulation procedure, validated by field data, was used in an analytical study of vein-wall closure and sill-pillar stress as influenced by fill modulus, rock modulus, and premining stress. Ratios of closure and pillar stress in the filled stopes to closure and pillar stress in the unfilled stopes are used as prediction indices for fill performance. In general, the support capability of fill increases dramatically as the ratio of fill modulus to rock modulus approaches 1. A significant reduction in closure .from the open stope--up to 75 percent--occurs with a relatively low-quality 10-ksi-modulus fill (rock modulus of 1,000 ksi). However, a higher quality fill is needed to achieve a substantial reduction in pillar stress from that of the open stope. A 100-ksi-modulus fill reduces pillar stress in both the 36-foot and l6-foot pillars (vein width is 10 feet) by about 50 percent relative to the open stope.

Jan 1, 1976

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989

By J. K. Whyatt

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [s 1 ?135 MPa (19,600 psi) oriented S 80° W). An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 2010

Provide better ventilation for mines by reducing air leakage around stoppings. Approach Most stoppings are constructed of concrete blocks and trowelled-on mortar and are not very airtight. Bureau of Mines research has shown that brushing on modified mortar containing fiberglass and/or other additives, that enhance strength and adhesion, minimizes air leakage around and through the stoppings. Airtightness is an important factor in building stoppings since an airtight stopping will provide for more efficient ventilation airflow and more cost-efficient use of the mine's ventilation system. How the New Technique Works After broken floor and rib material is removed, the stop-ping faces are covered with one or two coats of modified

Jan 1, 1982

By D. J. Parker

Owing to its flexibility, convenience, economy, ands availability, electric power is peculiarly adapted to the needs of the coal -mining industry. Because of such obvious advantages, the application of electricity has in recent years become more and more extensive and is now a most important factor in the Nation's coal prediction. With the introduction of this type of power into coal mines certain new, specific, and well-recognized hazards resulted. The question arises, therefore: Has the industry met these hazards squarely and. effectively? With respect to some individual companies, the answer happily is in the affirmative; with respect to the industry as a whole, there is much room for improvement.

Jan 1, 1933

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

By D. J. Parker, J. B. Benson, J. H. Bird, F. E. Cash

"INTRODUCTION The organic act that became effective July 1, 1910, imposes two very definite primary obligations upon the Bureau of Mines: (1) The prevention of loss of life and limb and the protection of the health of workers in the mineral industries, and (2) the conservation and scientific utilization of the country's mineral resources.The subject of this publication falls within the scope of both of these responsibilities by reason of the fact that (1) certain safety precautions are involved in combating even surface fires and, (2) although peat is not now, so far as known, utilized commercially or otherwise in this country as a fuel, it is extremely valuable agriculturally in at least one of our States, The justification for the conservation of such low-grade fuel through fire prevention appears warranted because of its present value to agriculture and the possible advantages accruing to future generations as a source of heat and power.Although the Bureau of Mines has published information on the origin and uses of peat, this is the first attempt to give out data concerning the prevention and control of peat-bog fires. Although the information presented here is restricted to the Lake Superior District, California, and Florida, there may be similar conditions in other sections of the country that have not come to the attention of engineers of the Bureau of Nines."

Jul 1, 1947