Search Documents

By J. M. Singer

Thermal, mechanical, and physical properties of virgin and heat-treated Pittsburgh seam coal were determined as part of a comprehensive study of combustion of monolithic coal block. The information was sought to help characterize pyrolysis and combustion processes in underground coal mine fires but should also prove useful in the study of in situ and surface coal gasifiers. Measured properties include thermal conductivity, specific heat, thermal expansion, density, compressive and tensile strength, porosity, and permeability. The transport property data were obtained (when feasible) in two mutually perpendicular directions of the anisotropic virgin coal material, and coal samples carbonized for 5 hours at temperatures of 350° C, 475° C, 500° C, 650° C, and 850° C. Other coals (Pocahontas No. 3, Sewell, and Illinois No. 6 seams) were investigated for porosity and relative permeability. Interdependence among all properties was evident from the results; however, only a few correlations could be developed owing to inhomogeneity of coal material and specimen variation, which had the effect of reducing the accuracy of measurement and increasing data scatter.

Jan 1, 1979

By S. H. Brooks

"IntroductionThis preliminary report deals with the effect of oxygen pressure on the ignition temperature and combustibility of oils, it is the third of a series which will present the results of an investigation being made by the Bureau of Mines, on oxygen-oil explosions. The purpose of this research is to obtain technical data that will serve as a basis for safety precautions general outline of the problem has been given in the first report (Serial 2507).The present experiments have resulted in (1) a method for determining spontaneous ignition points of oils in an atmospheric of oxygen under pressure; and (2) the determination of these ignition temperatures for three typical oils, one being an animal oil (sperm), one a vegetable oil (linseed), and one a mineral oil (""Moiloil A"").These experiments on explosibility of oil were performed in order to discover the general nature of the phenomenon, especially the order of magnitude of the temperature necessary for spontaneous explosion (120°C. and upwards) and the effect of pressure variation (negligible as regards ignition temperature but important in relation to the violence of the explosion). A continuation oftests should provide a basis for selecting the safest lubricants for high pressure compression of gases particularly air and oxygen; and should be of value when devising new specifications for lubricants, both in the government departments and the compressed-gas manufacturing industry."

Dec 1, 1923

By A. Gene Collins

The Bureau of Mines undertook research to determine the bromide and iodide content of Mississippi and Alabama oilfield waters of the Tertiary and Cretaceous Period to determine genetic relationships of the ions, to determine their origin, and to determine their genetic relation to petroleum. The 280 samples were analyzed after a pretreatment to remove interferences. The iodide was oxidized to iodate and was titrated with thiosulfate. The bromide was oxidized to bromate and was determined iodometrically. A computer was used to calculate the correlation coefficients of iodide to bromide and to other ions. The other ions are sodium plus potassium, calcium, magnesium, chloride, bicarbonate, and sulfate. The mineral content of the samples ranged from 52 to 1,760 mg/l for bromide and from 2 to 65 mg/l for iodide. The mean bromide-to-chloride and iodide-to-chloride ratios were 0.0065 and 0.0002. The correlation coefficient matrix and linear plots indicated a definite bromide-to-calcium relationship for the brines investigated.

Jan 1, 1967

By Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2007

By John P. Savage

This paper is one of a series being prepared by the United States Bureau of Mines on tunneling methods. The tunneling methods described are those used at the Ojuela unit of the Compania Minera de Penoles, S. A., the Mexican subsidiary of the American Metal Co., Ltd., of New York. The Ojuela unit is situated some 4 miles southeast of Mapimi, Durango. Mexico, the latter place being connected by a 15-mile narrow-gage railway with the standard gage railroad at Bermejillo, some 40 miles to the north of Torreon, the location of one of the company's smelters.

Jan 1, 1931

By Frank E. Cash

"INTRODUCTION The iron—ore ranges in the Lake Superior district are the Marquette in Michigan, Menominee and Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years.This information circular supplements, continues, and combines the data in Information Circular 7321,2/ including figures of 1944 and 1945.During the 6—year period 1940 to 1945, inclusive, 481,485,475 long tons of iron ore was shipped from the Lake Superior district. 4/ Michigan and Wisconsin shipped 93,787,648 tons, or 19,5 percent of the total, and employed annually an average of approximately 14,300 men; Minnesota shipped 387,697,827 tons, or 80,5 percent, and employed annually an average of approximately 9,300 men. The tons produced per man employed is much greater in Minnesota than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jul 1, 1947

By Oren C. Baptist

Umiat field contains the largest accumulation of oil discovered so far in Naval Petroleum Reserve No. 4 in Arctic Alaska. The Umiat anticline was tested with 11 wells; 6 produced oil in varying quantities. Behavior of the wells during testing was unpredictable. For example, one well was abandoned as a dry hole after all tests failed to recover any oil, yet an offset well, only 200 feet from the dry hole, produced 400 barrels of oil a day. The main oil reservoirs are less than 1,000 feet deep and are in the permanently frozen zone (permafrost). Reservoir pressures are low, and most primary production will be by expansion of gas-in-solution in the oil. Because of the unusual reservoir conditions and the difficulties encountered in drilling and completing the wells, the Department of the Navy asked the Federal Bureau of Mines to make laboratory studies of the reservoir sand to determine the cause of well plugging and to provide laboratory information, to be used as an aid in estimating oil recovery from frozen reservoir rocks under solution-gas expansion from low-saturation pressure conditions.

Jan 1, 1960

By Albert E. Long

During the summer and fall of 1948 the Bureau of Mines, in cooperation with the U. S. Geological Survey, conducted 6xperiments in diamond core drilling in the Phosphoria formation in southeastern Idaho and southwestern Wyoming. Nearly all of the diamond core drilling in the Phosphoria formation has been done by mining companies interested in finding and developing phosphate-bearing beds amenable to stripping. The recovery of sludge; and enough core (usually 30 to 60 percent) to identify certain marker beds produced by current drilling practices meets both the primary requirement of mining companies in determining depth of overburden and their secondary need to determine the phosphate content of relatively thick minable units whose general composition and nature are already fairly well established.

Jan 1, 1949

By E. G. Davis

The Bureau of Mines made laboratory-scale experiments to examine the technical possibilities of reclaiming manganese from slags produced by oxygen lancing of high-manganese pig iron. Ferromanganese was added to molten pig iron to yield a 4-to 5-percent manganese hot metal, which simulated a product obtainable from the blast furnace. This was injected with oxygen to reduce the metal to 1 percent or less manganese and form a slag containing about 40 percent manganese. The molten slag was water-quenched, treated with H2SO4) roasted at 660° C, and water-leached to give soluble manganese and iron sulfates. The sulfates were precipitated as hydroxides, converted to the oxide form, and smelted to produce a standard ferromanganese containing 74.6 percent Mn and 0.01 percent P. As an alternate method of manganese recovery, a manganese cell feed was prepared from the leach solutions and electrolytic manganese was produced. Direct smelting of the high-manganese slag resulted in 74.2 ferromanganese meeting ASTM specifications except for phosphorus content. The high phosphorus content of the metal and high slag-to-metal ratio obtained made this approach unattractive.

Jan 1, 1966

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By R. J. Leary

Oxidation testing of copper-clad steel strip was performed in a muffle furnace to determine whether copper in contact with steel scrap could be removed by oxidation in an airstream at high temperatures. Substantially all of the copper was oxidized before any significant iron oxidation occurred. The rate of copper oxidation was not affected by contact with iron. Copper oxide scale separated spontaneously from the underlying metal during cooling. Results indicate the possibility of removing light-gage copper coatings and components from ferrous scrap by oxidation in an incineration process.

Jan 1, 1965

By S. B. Levin

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. During the fall of 1942, the Bureau of Mines put down nine diamond-drill holes at the Cape Rosier zinc-copper-lead mine in Hancock County, Maine, that aggregated 2,883 feet of bore. These holes supplemented 13 holes, aggregating. 5,501 feet, put down on the property about 2 years earlier by the St. Joseph Lead Co. Veins of mixed sulfides were intersected in 15 of the holes drilled. Beneficiation tests were made on samples of ore obtained from old dumps. Zinc-copper-lead sulfides occur at the Cape Rosier mine as lenses in a zone of altered agglomerate beneath and between a series of diorite sills. The mineralized zone strikes F. 17° E. and dips southeast. Between July 1881 and September 1883 the mine produced about 10,000 tons of ore reported to have contained 20 percent zinc, 2.8 percent copper, and some lead. The crude ore was hand-sorted, and some. 3,000 tons were reported shipped.

Jan 1, 1948

By A. Gene Collins

Rapid, sensitive, and precise methods of determing major, minor and trace constituents of oilfield brines are needed. Several methods have been developed or adapted by the Federal Bureau of Mines at the Petroleum Research Center, Bartlesville, Okla. The following methods are described in this report: Spectrophotometric and volumetric for iodides and bromides; potentiometric for pH, alkalinity, acidity, borate boron, total boron, and organic boron; gravimetric for potassium; disodium ethylenediaminetetraacetate (EDTA) volumetric for total hardness, calcium, and magnesium; spectrophotometric for fluorides; and color comparison .for arsenic. Adequate sensitivity, precision, and accuracy were obtained for each method. The Bureau of Mines pioneered in research on the analysis of oilfield waters (2, 46, 47).6 However, several of these early procedures were quite time consuming. Also, they did not include methods for determining trace and minor constituents of brines.

Jan 1, 1961

By Terry J. Close

In 1985, at the request of the U.S. Bureau of Land Management, the U. S. Bureau of Mines studied part of the 56,623-acre South McCullough Mountains Wilderness Study Area (NV-050-435) in order to evaluate its identified mineral resources. The area studied is located in Clark County, NV, about 30 miles southwest of Boulder City. No mineral resources were identified. The study area contains the eastern part of the unorganized McCullough Mountain (McClanahan) mining district which has had no recorded production. Between 1911 and 1982, 23 lode claims were located in the part of the mining district that is in the study area; four of these claims are currently held by assessment (1986). A total of 11 mineral sites were found and examined during the U.S. Bureau of Mines investigations; 26 mine workings were examined. Of the 11 sites, four are within the study area, and seven are nearby. Of the seven nearby sites, six are adjacent to the west boundary and consist of precious-and base-metals bearing vein occurrences in metamorphic rocks. The seventh site is near the east study area boundary, and consists of a tungsten-bearing vein occurrence that is also in metamorphic rocks. The four sites within the study area consist of vein occurrences in metamorphic rocks that contain silver, gold, arsenic, lead, zinc, and copper. The veins at these four sites are too small and low grade to be classified resources; however, there are indications that three of the sites may have silver and gold resources at depth. Detailed delineation of the veins, and determinations of tonnages and grades are needed. This would entail additional mapping and sampling, trenching and drilling, and opening inaccessible workings.

Jan 1, 1987

By Oliver Bowles

The use of fire as a source of heat was the first step from primitive existence toward modern civilization, and heat has performed functions of inestimable importance throughout the ensuing ages. The first commercial steam engine invented in 1698 demonstrated that heat was an important source of power, and heat has since become the motivating force for railroad trains and steamboats as well as for machines in multitudes of factories. Aside from its function of supplying power, heat is an agent of vast importance in chemical reactions and engineering processes. Because of the high temperature of steam under pressure, losses by radiation from boilers and pipes become excessive unless the radiating surfaces are covered with insulating materials. Insulation is important also for hot-water pipes and many other types of equipment from which heat may radiate. Radiation losses from heated surfaces increase rapidly

Jan 1, 1943

By Danton L. Paulson

Elevated temperature electrical resistivity measurements were made by the Bureau of Mines on arc-melted, spin-cast, and hot-pressed columbium carbide¬carbon (CbC-C) and zirconium carbide-carbon (ZrC-C) materials up to 2,000° C. The CbC-C materials displayed electrical resistivity values ranging from 35.20 microhm cm at 23° C for hot-pressed material containing 12 wt pct carbon to 242.64 microhm cm at 1,622° C for arc-cast material containing 17.0 wt pct carbon. Electrical resistivity values ranged from 29 microhm cm at 20° C for arc-cast ZrC-C containing 16 wt pct carbon to 279 microhm cm at 1,951° C for hot-pressed ZrC-C containing 21 wt pct carbon. Data from a previous report were included to establish comparison between the electrical resistivities of the CbC-C, ZrC-C, and HfC-C systems.

Jan 1, 1969

By Raghoottma S. Pandurangi, Mohindar S. Seehra

"The interaction of amorphous 1ilica particles with several hydrogen bonding agents (H2O, C2H5OH, C7H2NO) was investigated by monitoring the changes in the bulk and surface IR vibrational modes of silica using photoacoustic spectroscopy. It is argued that the intensity of the silanol band at 3747 cm-1 provides (an inverse) quantitative measure of the interaction or surface groups, along with the shift in the broad hydroxyl band, the interaction following the order C7H2NO > C2H5OH > H2O. Index Headings: Silica; Surface vibrational modes; Photoacoustic spectroscopy; Hydrogen bonding agents.INTRODUCTIONThe use of m spectroscopy to study the adsorption on solid surfaces is well documented in the literature.1 2 For example, hydroxylation of a clean silica surface results in the formation of the free silanol group Si-OH, with a sharp IR band near 3747 cm-1• Further hydroxylation produces a broad band near 3500 cm-1, which is believed to result from various hydrogen-bonded silanol bands leading to a multilayered surface structure of few nm.3-5 Earlier studies had indicated a relationship between the surface silanol band and various chemical activities of silica such as cytotoxicity, 7- 9 catalysis, 10-12 and others.13 Recent studies from our group14-in which the intensity of the silanol band and cytotoxicity of silica, heat-treated at various temperatures up to 1095°C, were investigated have provided a strong correlation between cytotoxicity and intensity of the silanol band.Coating of silica by PVPNO (polyvinyl-2-pyridine N-oxide with the empirical formula C7H8NO), a strong hydrogen bonding agent, is known to reduce the cytotoxicity of silica, presumably by chemically blocking the silanol groups from phospholipids.15 This interaction of the hydrogen bonding agents with the silica can be studied by m spectroscopy, and Knozinger16 and Rouxlet and Semples11 have used transmission m spectroscopy to study the effect of various chemicals on the surface IR modes of silica. However, one of the major disadvantages of transmission IR spectroscopy is that the sample preparation (grinding and mixing with KBr and pelletizing) usually distorts the surface modes (see, e.g., Ref. 14) and there is always a doubt about the effect of the sample preparation on the measured properties. In recent years, photoacoustic (PA) spectroscopy has become the technique of choice for studying the IR spectra of samples in their natural state, since no sample preparation is necessary.18•19 Moreover, according to a recent paper, 20 the relative intensity of the surface modes in PA spectroscopy of silica particles is much higher than that in transmission FT-IR spectroscopy. Consequently PA spectroscopy is ideal for studying the surface chemistry. In this work, we have used PA spectroscopy to investigate the interaction of three hydrogen bonding agents (C7H8NO, C2H50H, and H20) with the silica surface by monitoring changes in the surface m modes. Our results show that the surface IR modes get perturbed to a larger extent than the bulk IR modes in interaction with the hydrogen bonding agents. Moreover, whereas in the earlier studies, the shift of the broad silanol band near 3500 cm-1 was used as a measure of the interaction with hydrogen bonding agents,16•17 here we show that the relative decrease in the intensity of the sharp silanol band near 3747 cm-1 also serves as a quantitative parameter for the relative surface coverage and surface modification. Details of this work are given below."

Jan 1, 1990

By William A. Sloan

"In smelting operations, finely divided material called ""flue dust"" is carried by the moving gases from the roasters and furnaces; it is partly settled and recovered in the flue system. The flue dust from copper smelters contains a high percentage of copper, usually some gold and silver, and occasionally other valuable metals. It is too valuable to throw away and in present practice is returned to the smelting furnaces for re-treatment. A part of this material again passes out with the gases and forms a circulating dust load in the system. The dust that passesout of the stacks into the atmosphere is an important source of loss in copper smelting. Loss of values also occurs by dust being blown away while in transit from the flues back to the furnace, and of course the greater the amount of rehandling the greater this loss.Dust carried in the gas currents causes corrosion of the roof arches in reverberatory furnaces. Returning flue dust to the furnace increases the quantity of suspended dust. Corrosion reduces the life of the arches and shortens the length of furnace campaigns; also the corrosion of arches limits the temperature at which a furnace may be operated. Every ton of material that must be re-treated in the furnaces reduces correspondingly the amount of new ore or concentrates that could be smelted.As the present tendency is toward finer grinding in flotation plants smaller particles will need to be treated at the smelters, increasing the difficulty of preventing losses in flue dusts. Many schemes and processes for a more economical method of treating flue dust have been proposed or tried, but in the main none of them has been successful."

May 1, 1928

By William C. Cooley

A review was made of two Russian books and a chapter from a third book dealing with pipeline transport of coal. Emphasis was placed on hydrotransport of coarse coal in underground mines or surface pipelines. The books reviewed were: "Means of Increasing the Effectiveness of Hydrotransport," by V. N. Pokrovskaya (1972), "Parameters and Modes of Hydraulic Transport of Coal" by V. V. Traynis (1970), and the chapter "Calculations of Hydrotransport of Useful Minerals and Waste Rock" from the book "Hydromechanization of Opencast Workings" by G. A. Nurok (1970). All three are unique and useful additions to the world literature on hydrotransport. The Traynis book reveals the development and results of circular wheel stand tests to simulate hydrotransport in horizontal pipes, which is a potentially outstanding contribution to slurry pipeline technology. Graphical data and equations are presented which suggest that headlosses for coarse coal can be predicted with good accuracy for pipe sizes up to 14 inches in diameter. Wheel stands permit tests for pipe wear and lump degradation without recycling coal through pumps. Recommendations are made for wheel stand tests and for correlation of existing data.

Jan 1, 1976

By John B. Knaebel

This paper is one of a series being prepared by the Bureau of Mines on mining methods and costs at various mines in the United States, Canada, and Mexico, and is a description of practice at the Edwards mine of the St. Joseph Lead Co. ACKNOWLEDGMENTS The cooperation and assistance of the officials of the St. Joseph Lead Co. in permitting publication of this paper and providing every facility for its preparation are gratefully acknowledged. Especial thanks are extended R. J. Mechin, manager, R. F. Mitchell, mine captain, and J. S. Brown, geologist, for their generous aid, and the assistance of W. H, Weijola, mine engineer in assembling some of the illustrations is deeply appreciated, The helpful suggestions of C. F. Jackson, principal mining engineer, U. S. Bureau of Mines, are gratefully acknowledged.

Jan 1, 1932