Search Documents

By K. R. Dorman

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed a five-piece precast concrete drift set for a small opening and tested it to destruction in a straining frame. Twenty-seven tests were made with three sizes of members using three loading conditions. In addition, six tests were made with sets in a distorted configuration, Test results and typical failure patterns are presented. A comparison of results with those previously reported for the three-piece set shows the five-piece set supports considerably larger total loads than does the three-piece set of equivalent cross section designed for the same size of opening. Recommendations are made for improvements in design.

Jan 1, 1969

By Oliver Bowles

"Asbestos" is not the name of a distinct mineral species but is rather a commercial term applied to fibrous varieties of several minerals. The origin and significance of names applied to asbestos by early writers are discussed in the section devoted to sources of supply and terms employed in ancient times. VARIETIES The most useful variety of asbestos is chrysotile, a fibrous serpentine the composition of which is expressed by the formula H4Mg3Si209. Chrysotile is characterized by a strength and flexibility that permit the use of the longer fibers for spinning. The bulk of the world production of both long and short fibers, is of this variety.

Jan 1, 1935

By John W. Thatcher

A demountable X-ray tube vacuum spectrograph was designed by the Bureau of Mines for the determination of long-wavelength X-ray spectra from the light elements. This instrument was operated for both secondary and combined primary-secondary excitation of the aluminum K-series. There was an increased analytical sensitivity for elements in period 3, and an indication that with improved X-ray tubes or direct election excitation of the sample, X-ray determination of elements in period 2 is also possible.

Jan 1, 1965

By H. G. Iverson

Solid state reactions of manganese with silica were investigated in high-temperature tests. Reactions of 0.5 to 4.0 moles manganese (Mn) with 1 mole silica (SiO2) at 1,100° C and of 2.0 Mn:SiO2 mole-ratio mixtures at 1,000° to 1,150° C yielded products consisting of a slag phase and a metallic phase. At 1,100° C, the slag phase from reactions of the low Mn:SiO2 mole-ratio mixtures was composed of SiO2 and rhodonite (MnSiO3), and the slag phase from the high Mn:SiO2 mixtures was composed of MnSiOs and tephroite (Mn2SiO4). The metallic phase from the corresponding low Mn:SiO2 mole-ratio reactants consisted of two manganese silicides, Mn5Si3 and Mn3Si; from the high Mn:SiOg mixtures, it was Mn and the manganese silicide (Mn5Si). For the higher mole ratios of MnSiO2 the manganese content in the metallic phase increased, while the manganese and silica contents of the slag phase remained nearly constant. The slags did not contain free or uncombined manganese oxide (MuO). For the 2.5 to 4.0 Mn:SiO2 mole-ratio mixtures reacted at 1,100° C, the maximum quantities of silica reduced and of the manganese in the slag appeared to become asymptotical at about 41 and 48 percent, respectively. A brominating procedure was developed that was highly selective in removing the metallic constituents from the reaction product, leaving the slag phase as residue. X-ray diffraction patterns were obtained on prepared silicides Mn5Si, Mn3Si, and MnSi.

Jan 1, 1967

By J. W. Town

Recrystallization studies on chrome-bearing spinel materials were made by the Bureau of Mines to determine the effects of certain fluxing agents and cooling rates on the chromium-to-iron ratio of recrystallized spinel. Statistically designed and evaluated tests showed that the ratio of chromium to iron in naturally occurring chrome spinel could be increased from 1.5 to 1 to over 7 to 1 and that the ratio of chromium to iron in the chrome-spinel in a stain-less steel slag could be raised to over 18 to 1. Silica, magnesia, and lime had significant positive effects, while alumina had a significant negative effect. Cooling rates of 200 C per hour in a programmed spiral globar electric furnace were satisfactory for growing crystals of recoverable size.

Jan 1, 1967

By D. Randolph Berry

The U.S. Bureau of Mines awarded a contract to Foster-Miller Associates, Inc. (FMA) to provide recommendations on the safest, most practical methods for complying with new regulations requiring that all underground coal miners have a self-contained, self-rescuer (SCSR) -a device capable of supplying, in an emergency, 1 hr of self-contained oxygen (no breathing of mine air). This report develops information and recommendations which could be used during the early stages of nationwide compliance, especially in the areas of inspection, testing, and underground storage of SCSRs. Volume I contains an Executive Summary, Introduction, Definitions, Recommended Guidelines for District Managers and Mine Operators, and a Storage Plan Checklist and Sample Form.

Jan 1, 1981

By F. J. Wiebelt

Production of small tonnages of asbestos has been reported from 18 California counties; 16 additional counties have occurrences of asbestos. The counties in the northern part of California that have had a recorded production are: Alameda, Amador, Calaveras, Contra Costa, E1 Dorado, Napa, Nevada, Placer, Shasta, Siskiyou, Trinity, and Tuolumne. No deposit in the State has maintained consistent production. Serpentinized peridotites (potential chrysotile-bearing rocks) are widely distributed in the coast ranges, Klamath Mountains, and western foothills of the Sierra Nevada.

Jan 1, 1958

By Harold M. Smith

[Important discoveries of new oil fields were made in 1937 in the State of Illinois. Oil production, which was virtually constant during 1934, 1935, and 1936 at about 4,400,000 barrels a year, a increased to 7,499,000, barrels during 1937, and in 1938 this production was trebled. In 1939, 94,302,0003/ barrels were produced (almost foot times the 1938 quantity), making Illinois one of the cost important oil-producing areas in the United States. The Bureau of Mines has analyzed 35 samples of petroleum from these new Illinois fields and presents the analyses herein. Included with them in this report are analyses of seven samples from fields developed before 1936.]

Jan 1, 1940

By R. E. Heithecker, D. B. Taliaferro

"INTRODUCTION Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Gore specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, ""connate"" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and avail¬ability of oil and as within a reservoir and in devising efficient means for their withdrawal.Examination of bottom-hole samples of oil gives valuable information concerning the amount of gas in solution in the oil within the reservoir and the resultant shrinkage of the oil when the gas is released. Producing characteristics of reservoirs nay be determined by means of subsurface pressure and temperature gages and measurements male at the wellhead; however, unless reliable core analyses are available, these data have only limited use in any quantitative study of reserves. In such a study the quantity of oil, gas, and water contained in a unit volume of the reservoir formation is extremely important. Although reliable methods of analyzing cores have been developed and the data thus obtained are valuable, their applications become more limited or reservoirs at higher temperatures and pressures are discovered. This condition results almost entirely from the fact that in recovering a core from a formation of high pressure and temperature by present methods a large part of the fluid content of the core is lost or contaminated to an unknown extent. For a number of years most petroleum engineers have held that if this loss and contamination of the fluid content of a core were eliminated, the value of core analyses would be increased greatly."

Nov 1, 1939

The Bureau of Mines performed cratering experiments in a homogeneous granite to test scaling laws for charge weights of 0.00476, 0.0220, 0.0900, 0.304, and 1.03 lb. Agreement among the data was best when empirical scaling exponents greater than one-third were assumed. Although the analysis showed that the best empirical scaling exponents were 0.37 for crater volume, 0.38 for crater radius, and 0.39 scaling for crater depth, all three crater dimensions could be scaled with a 0.38 scaling exponent.

Jan 1, 1970

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By Harold M. Smith

Important discoveries of new oil fields were made in 1937 in the State of Illinois. Oil production, which was virtually constant during 1934, 1935, and 1936 at about 4,400,000 barrels a year, a increased to 7,499,000, barrels during 1937, and in 1938 this production was trebled. In 1939, 94,302,0003/ barrels were produced (almost four times the 1938 quantity), making Illinois one of the cost important oil-producing areas in the United States. The Bureau of Mines has analyzed 35 samples of petroleum from these new Illinois fields and presents the analyses herein. Included with them in this report are analyses of seven samples from fields developed before 1936.

Jan 1, 1940

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By J. R. Ross

Techniques for recovering scandium from uranium plant iron sludges and from wolframite concentrates are described. The best procedure found comprised (1) dissolution with sulfuric acid, (2) preliminary concentration by solvent extraction with a primary alkyl amine, (3) further enrichment and purification by a combination of ion exchange, solvent extraction, chemical precipitation, and calcination. Recovery of scandium from these raw materials, which contained 0.058 and 0.14 percent scandium, ranged from 83 to 90 percent in products analyzing 99.6 to 99.9 percent scandium oxide.

Jan 1, 1965

By W. A. Calhoun

Progress made in a second and final metallurgical investigation made by the Bureau of Mines of near-surface Hawaiian bauxitic deposits from Kauai, Maui, and Hawaii Islands, and on a deeper deposit from Kauai, is reported. Previously reported Al2O3 extractions were increased by modifying conventional processes to fit the ore being tested. Increases in Al2O3 extraction were: Kauai, from 82.8 to 95.4 percent; Maui, 85.5 to 94.1 percent; and Hawaii, from 79.5 to 86.4 percent. Use of a "caustic-reduction sinter, leaching, and magnetic separation process" for Al2O3 extraction also produced an iron concentrate of commercial grade, except for titanium content. No successful method was developed for the recovery of a satisfactory titanium concentrate.

Jan 1, 1967

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphoric acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

The content of the book covers: (1) The theory of the Eötvös torsion balance; derivation of the working formulas; description of the instrument; method of observation; relation of the magnitudes observed to the lines of force and the level surfaces of gravity; corrections or normal effects, near and distance terrane; subterranean effects; effects due to certain mathematical bodies. (2) Notes on the practical employment of the Eötvös torsion balance; initial testing of the instrument and of accessories; hints on planning the survey; work at the station site; office computation and plotting of results; the interpretation of the results: (3) A description of the instrument and instructions for its manipulation. This book was the best discussion in English on the theory and use of the Eötvös torsion balance and is surpassed only by a later paper by the same authors that covers much of the same ground. The book is suitable for a textbook for beginners, and advanced students will find it of use. It should be available as a reference book in all geological libraries and in all torsion balance department offices.

Jan 1, 1929

By Z. Zhiqun, V. A. Marple, B. Y. H. Liu

"IntroductionIt is commonly understood that aerosol particles may be injurious to human health if they are of a size that enables them to enter the respiratory tract. Coal Workers' Pneumoconiosis (CWP) is one disease known to be caused by coal mining related particles.The location in the respiratory tract where the particles are deposited is primarily a function of the equivalent aerodynamic diameter (EAD) of the particle. The equivalent aerodynamic diameter is the diameter of a spherical particle with a density of 1.0 gm/cm3 with the same falling speed as the particle in question. For a spherical particle the calculation is rather simple in that the equivalent aerodynamic diameter is simply the diameter of the particle in question multiplied by the square root of the density of the particle. For irregularly shaped particles, such as coal particles, there is no simple way to make the EAD calculation. For example, Figure 1 is only one of an infinite variety of particle shapes that can be found in practice and the aerodynamic size of this particle and, therefore, its deposition location in the respiratory tract would be nearly impos-sible to estimate accurately.The normal method for determining the aerodynamic diameter of particles has been to experimentally measure the size of the particles in a settling chamber or with an inertial classifier such as an impactor, cyclone or a centrifuge, since inertial classifiers have the property of classifying the particles according to their aerodynamic diameters."") However, these devices can only give limited information on the EAD of a single particle with a specific shape. Impactors and cyclones, for example, collect particles in size ranges and not at a specific size, so the determination of the EAD of a specific particle is not possible. A centrifuge, on the other hand, can measure the EAD of a specific particle but the equipment is costly and procedure laborious, and it may not be possible to disperse a particle of a specific shape into the centrifuge. The centrifuge can be used to determine the EAD of clusters of spheres in various arrays, but introducing particles of a specific irregular shape may not be feasible. Furthermore, the EAD is a function of the orientation of an irregularly shaped particle and the orientation of a particle in an inertial classifier is unknown. The orientation may also vary as the particle passes through the classifier.Because of the difficulty in determining the EAD of an irregularly shaped particle, we have undertaken a program to apply theoretical numerical methods to calculate the EAD of any shape particle. In our laboratory we have, for some time, been using numerical methods to determine the flow field of air within instruments such as impactors, (2) inlets, (3) and virtual impactors (4) Recently, this technique has been expanded into the three-dimensional regime, and the flow fields and particle motion characteristics within cyclones (5) and glove boxes have been studied. We have now begun to use these numerical three-dimensional flow programs to study the flow field around irregularly shaped particles to determine their drag coefficients, falling speed, and thus, their EAD."

Mar 1, 1989

By R. V. Lundquist, H. Leitch

The solubility characteristics of three calcium aluminates , 12Ca0 · 7A120½ 3Ca0 A1203 , and 4Ca0 A12 03 Fe2O3 , were determined in water and in solutions of NaOH and Na₂ CO₂ to more clearly define their role in relation to the recovery of aluminum by the lime sinter and the lime - soda sinter processes . The calcium aluminates were prepared by sintering stoichiometric mixtures of CaCO3 , Al2O3 3H20, and Fe 0 at 1,375 ° C. The rates and extent of aluminum extractions were determined . The aluminum extractions from the aluminates were dependent on the presence of carbonate ions in the leach solutions , temperature , time , leach solution composition , and solid - liquid ratio of the slurry . The aluminum extracted from the calcium aluminates in water and in NaOH solutions varied from 4.6 to 22.9 percent . Virtually , complete extraction could generally be obtained for 12Ca0.7A120 and 4Ca0.A12 03 • Fe₂ 03 ; in one instance it was obtained for 3Ca0.A1203 , when an excess of carbonate ions was present over that required for the conversion of all of the calcium in the aluminates into CaCO3 . In some cases of poor aluminum recoveries , extractions could be improved by regrinding and releaching the solid residues .

Jan 1, 1964

By Wallace W. Roepke

Four bit designs, two conical and two radial, were tested in coal against a 60° conical reference bit to obtain data on orthogonal cutting forces and primary respirable dust generation. One conical and one radial design were modified by the Bureau of Mines for these tests. Results were mixed: One radial bit used substantially lower overall cutting forces and specific energy than the other bits and was the only cutter lower on energy and most forces than the standard 60° bit. How-ever, it generated more specific and total dust than any other bit. The four bits were also tested for incendivity, with a 90° plumb-bob bit as the reference. The frictional ignition tests were designed to simulate both trimming top rock and cutting such rock during advance on-sump. Results of these tests were also mixed. The radial bits were substantially less incendive than the reference bit and caused no ignitions in either top trimming or sump modes. Only the modified mushroom-tipped conical bit caused ignitions. Bits similar to this modified design should not be used on drum-type miners in gassy mine areas; in-stead, the other types of bits tested should be used to reduce ignition potential to a minimum.

Jan 1, 1983