Search Documents

By Felix duBreuil

The present sampling procedure for evaluating the rock dusting conditions in a coal mine is time consuming. This study considers means by which this procedure could be simplified. Surveys were conducted in six coal mines in Pennsylvania to determine the in¬combustible content of the deposited dust. Some 2,000 samples were analyzed and statistically evaluated. It is suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error.

Jan 1, 1972

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By J. P. Powell

Records show that systematic water flooding was begun as early as 1935 in Greenwood County and in 1937 in Butler County. Water flooding on some earlier projects in Greenwood County were described in a Bureau of Mines Report of Investigation.2/ This report presents a discussion of 4 projects -2 in Butler County, 1 in Greenwood County, and 1 in Butler and Greenwood Counties. The location of these projects is shown in figure 1. The projects have been in operation 6 to 12 years and have recovered about 6.6 million barrels of additional oil from the injection of 84.7 million barrels of water. Three of the projects take advantage of the elevation of the nearby hilly terrain, and water from the treating ponds flows by gravity through the filters into the clear-water tanks. By utilizing gravity flow, fewer pumps and less electrical energy is required, resulting in more economical operation.

Jan 1, 1956

By Sean Gallagher

The restricted workspace present in low-seam coal mines forces workers to adopt awkward working postures (kneeling and stooping), which place high physical demands on the knee and lower back. Method: This article provides an analysis of injury claims for eight mining companies operating low-seam coal mines during calendar years 1996-2008. All cost data were normalized using data on the cost of medical care (MPI) as provided by the U.S. Bureau of Labor Statistics. Results: Results of the analysis indicate that the knee was the body part that led in terms of claim cost ($4.2 million), followed by injuries to the lower back ($2.7 million). While the average cost per injury for these body parts was $13,100 and $14,400, respectively (close to the average cost of an injury overall), the high frequency of these injuries resulted in their pre¬eminence in terms of cost. Analysis of data from individual mining companies suggest that knee and lower back injuries were a consistent problem across companies, as these injuries were each among the top five most costly part of body for seven out of eight companies studied. Application/Impact: Results of this investigation suggest that efforts to reduce the frequency of knee and low back injuries in low-seam mines have the potential to create substantial cost savings.

Jan 1, 2009

By David E. Siskind

The Bureau of Mines has studied the fracturing and associated damage occurring in the vicinity of blastholes from five shots fired in the shale pillars in the White Pine copper mine, White Pine, Mich. Four types of explosives (AN-FO, commercial extra dynamite, ammonia gelatin dynamite, and a low-density, low-velocity permissible) were used. Cores were taken from the blast region and examined by ultrasonic and petrographic techniques. Pulse wave velocities were measured across the core diameters, and thin sections showing cracks and changes in lithology were examined in an attempt to establish zones of damage. Cores from the blast regions and areas near pillar free faces were found to have abnormally low pulse velocities. Petrographic study of the thin sections showed that the negative velocity anomalies were caused by cracks in the cores. Crushing and extensive fracturing prevented meaningful measurements on core fragments from the immediate blast vicinities. Compositional, changes and other rock nonuniformities, such as joints and preexisting fractures, tended to mask detailed damage differences among the four explosives; however, the two most energetic explosives (extra dynamite and ammonia gelatin dynamite) produced damage zones two to three times as large as the AN-FO and low-velocity permissible explosives.

Jan 1, 1973

By Richard A. Dick

In this report commercial blasting compounds are classified according to their nitroglycerin (or equivalent explosive oil) and ammonium nitrate content as dynamites, gelatins, blasting agents, military explosives, and blasting , accessories. The ingredients and more significant properties of each explosive are tabulated and briefly discussed. Data are summarized from various handbooks, textbooks, and manufacturers' technical data sheets, together with the author's personal experience; however, this report is not intended to be a technical handbook, since it does not deal with blasting techniques. Instead, it seeks to acquaint the reader with the great variety of explosives, available, their advantages and disadvantages, and their general areas of application. Properties discussed are weight strength, cartridge strength, detonation velocity, density, detonation pressure, water resistance, and fume class. The weakness of the strength rating system and the importance of detonation pres- , sure, density, and detonation velocity in rating explosives are discussed. The terms "blasting agent" and "slurry," which are often misused, are defined. Trends indicate that blasting agents (that is, blasting mixtures with none of of the ingredients singly classified as an explosive), particularly high-density slurry blasting agents, will dominate the explosives field in the future.

Jan 1, 1968

By Foster Fraas

Under a very high vacuum of 10-8 torr the transfer of terrestrial mineral beneficiation methods to the vacuum ambient of extraterrestrial locations such as the lunar surface was investigated. In the size range for the electro-static and magnetic separation of ores (minus 35 plus 150 mesh) there is no adhesion of particles produced by crushing and grinding due to the limited contact area, and for repeated contacts area size has a frequency of occurrence in accordance to the normal law. The photoelectric effect which is successful in separating a few minerals in an air ambient has a wider application in a vacuum, while the lack of air viscosity and sound transmission provides for high feed velocities and the adaptation of particle vibration to dispersion and grinding. Contact electrification is reversible upon return to atmosphere.

Jan 1, 1970

By R. Hogg, T. H. Dumm

"The mathematical treatments used in the evaluation of particle size distribution from pipet-withdrawal centrifuge data are reviewed. An error in the published procedure for multiple-sample withdrawal systems is pointed out and a corrected formulation is presented. An alternative treatment, based on a piece-wise linearization of the size distribution is described. Computer simulations of the analytical and data evaluation procedures indicate that the errors in the original formulation are not generally serious and that the corrected and alternative procedures lead to very similar estimates. Except for some cases involving very narrow size distributions, the alternative approach appears to give slightly closer estimates of the size distribution. Comparisons based on actual experimental data are also described.1 IntroductionSedimentation methods are widely used for the determination of particle size distributions. The procedures are relatively simple to use and the results are essentially absolute, requiring no external calibration. Gravity sedimentation is typically applicable to particles in the size range of about I to 50 pm and generally involves measurement of the relative concentration of particles as a function of depth and time in a dilute suspension. Particle size is calculated using Stokes, law:"

Mar 1, 1989

By Michael G. Zabetakis, Aldo L. Furno, Henry E. Perlee

The Bureau of Mines conducted an experimental study with liquid and gaseous hydrogen to determine the hazards associated with the use of liquid hydrogen as an ionizing particle detector in bubble chambers . The glass window , the vacuum chamber , and the vent system were investigated . In addition , a study was made of the detection and ignition of escaping hydrogen and of the available electrical equipment for use in hydrogen atmospheres . Materials such as tempered glass , aluminum , and stainless steel are not penetrated readily by the small fragments formed when fully tempered glass is shattered and propelled by hydrogen at initial pressures up to 100 psig ; long , slender fragments from untempered glass may penetrate thin walls of relatively soft materials such as rubber gaskets and lead . Hydrogen can be vented satisfactorily from a vacuum chamber with a well - designed vent system . However , the rapid leakage of hydrogen into the surrounding air is a serious problem because the available detectors are satisfactory only when the accumulation of hydrogen is slow . Much of the electrical equipment currently available was designed for use in hydrogen- air atmospheres .

Jan 1, 1963

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By J. P. McGee

A 1,000-hour test with a gas turbine at 1,200° F showed a working fluid of 1 gr of ash per 100 scf of power gas (79 percent of the ash 7 to 35 microns in diameter) to be excessive for acceptable blade wear for commercial practicability. Blades in the turbine consisted of about 20 percent each of chromium, cobalt, and nickel; 3 percent molybdenum; 2-1/2 percent tungsten; and smaller amounts of manganese, columbium, and tantalum. Erosion of both the fronts and backs of the turbine nozzles was particularly heavy, the trailing edges being worn to a featheredge. Erosion of the buckets was less marked, although the leading edges were somewhat pitted. A refractory-lined combustor performed efficiently and with little abrasion of the lining by the ash-laden gas.

Jan 1, 1969

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium, chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained, but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process. In all of the processes suggested for the recovery-of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation.

Jan 1, 1934

By John C. Machisak

THIS INFORMATION CIRCULAR covers the calendar year 1055 and contains statistical data on employment and injuries pertinent to metal and nonmetal mining and to their mills and processing plants that are voluntarily reported annually to the Federal Bureau of Mmes. This report, unlike previous publications, lists not only production and development workers but also office employees associated with mining and milling or processing. The last publication m the series, Information Circular 7798, Injury Experience in the Metal and Nonmetal Industries, 1954, also contains unpublished injury and employment statistics for 1943 through 1953. The Bureau is authorized to request data on injuries and employment from operators in the metal- and nonmetal-mining industries. The information voluntarily submitted by these operators contributes immeasurably to the promotion of safety in the mineral mining industries as it discloses the hazards to which metal and nonmetal workers are continually exposed during mineral extractive operations.

Jan 1, 1959

By J. G. Kirby

The number of petroleum refineries in the United States continued to decline during 1954, and according to the Bureau of Mines annual survey there were 326 refineries with a total daily throughput capacity of 8,420,630 barrels, as of January 1, 1955. The increase in capacity for the year was 413,733 barrels daily, while the number of refineries declined 11. The capacity of the average refinery to process crude oil increased during 1954 from 23,759 barrels daily to 25,830. Breaking down the crude-oil capacity increase, by refining districts; 32 percent was installed at refin¬eries located in the Texas Gulf Coast district, 25 percent in the East Coast district, and 13 percent in both the Louisiana Gulf Coast and the California districts. The Appalachian No. 1, Texas Inland, and New Mexico refining districts reported declines in capacity during the year. Additional crude-oil capacity under construction, January 1, 1955, totaled 146,800 barrels daily. Included in this total are 4 new refineries, 1 each in California, Minnesota, New Mexico, and Washington. In addition to the' new facilities, equipment producing 1.49,550 barrels daily is being replaced.

Jan 1, 1955

By D. G. Foot

The Bureau of Mines investigated energy-efficient methods for recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite, and carnallite. Six sulfate-chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2 to 22.2 pct K20, and recoveries from 84 to 99 pct. Sylvite flotation from chloride evaporites, with amine collector, recovered 90 to 97 pct of the potash in a concentrate containing 54.3 to 60.3 pct K20. Fatty acid flotation of the high-sulfate evaporite recovered 78 pct of the sulfate minerals in a 27.8-pct-K20 concentrate. Flotation of the chloride minerals with amine collector recovered 80 pct of the potash in a 59.7-pct-K20 concentrate. Solar evaporation of 10,000 gal of brine recovered 99 pct of the potash in a crude evaporite containing 24.5 pct schoenite and 20 pct sylvite. Continuous flotation in a 100-lb/h process research unit recovered over 95 pct of the potash in schoenite and sylvite concentrates containing 28.0 and 62.3 pct K20, respectively. An economic evaluation suggested a rate of return of 3 pct for a new facility and 9 pct if. the process is adapted to fit an existing plant.

Jan 1, 1984

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By Jack C. White

The purpose of this Bureau of Mines research was to determine the technical feasibility of direct sulfuric acid digestion of Florida land-pebble phosphate matrix. Preliminary tests in a continuous digestion circuit showed that 92 to 96 percent of the P2O5 contained in the matrix was extracted, while the P.05 concentration in the product acid ranged from 21 to 30 percent. The waste filter cake contained about 1 percent P205 and up to 18 percent water. These sandy compact filter cakes, comprised mostly of quartz and gypsum, appeared to be suitable for backfilling and reclamation of mined lands.

Jan 1, 1975

By R. W. Hiteshue, R. W. Fridy, W. Kawa

A study of the production of coronene , a high - melting ( 440 ° C ) , highboiling ( 525 ° C) , polynuclear hydrocarbon , was made by the Bureau of Mines to determine the maximum yield obtainable by the hydrogenation of coal and coalderived materials . Experiments were made with anthracite and bituminous coals and with asphaltenes and centrifuged residue obtained from heavy oil produced in a pilot plant by the hydrogenation of a bituminous coal at 2,000 psi and 480 ° C. With anthracite , yields of coronene of 0.5 to 0.7 wt pct of moistureand ash - free coal were obtained at 6,000 to 8,000 psi , 700 ° to 750 ° C , and a residence time of 30 minutes . With bituminous coal , yields averaging 0.4 wt pct of maf coal were obtained at 6,000 psi , 800 ° C , and 30 minutes ' residence time . With asphaltene and centrifuged residue , yields of less than 0.02 wt pct of maf coal were obtained at 6,000 psi , 700 ° C , and 60 minutes ' residence time .

Jan 1, 1964

By Hillary W. St. Clair

This report describes an experimental method for determining parameters for the rate of reaction of CO2 with solid carbon. The method involves the simulation of a flow reactor by a mathematical model based on a hypothetical multistage reactor which permits calculation of the analyses of effluent gas and carbon consumed as functions of the flow rate and duration of the reaction. The method is applied to experimental data on the reaction of coke with CO2 in fluidized-bed and fixed-bed flow reactors. A method is described whereby two parameters may be determined simultaneously. The method involves a reiterative procedure that finds the values of the parameters that minimize the sum of squares of deviation between calculated and observed analyses of the effluent gas.

Jan 1, 1971

By Joe B. Rosenbaum

New applications and concepts of solvent extraction as a unit operation in extractive metallurgy have been developed in the last decade. Wider use is being made of established solvent extraction techniques in processing spent nuclear fuel elements and in winning columbium-tantalum, hafnium-zirconium, thorium, tungsten, uranium, and vanadium. Commercial application has been extended to recovery of beryllium, boron, bromine, copper, molybdenum, phosphorus, rare-earth metals, and rhenium. Systems in use and proposed typically extract metals or salts as anion, cation, or neutral species from aqueous media by reaction with a recycleable organic reagent.

Jan 1, 1971