Search Documents

By Mark P. Meyer

This U.S. Bureau of Mines publication presents salient information in abstract form on 247 coal deposits in Alaska. Coverage includes currently producing deposits and deposits that appear to have commercial production potential. Data arc taken from coal properties identified by the U.S. Bureau of Mines minerals availability program and by a literature search. Infrastructural and institutional factors affecting coal development in Alaska are also discussed.

Jan 1, 1987

By D. J. Parker, D. Harrington, L. H. Harrison

"INTRODUCTION The necessity for protection against the hazards of lightning manifests itself from time to time in the mining industry by reason of loss of life, damage to electrical equipment, fires in surface structures at mines, and accidents in the handling and use of explosives. This paper is intended to assemble, correlate, and present some of the salient points embodied in the available literature on the subject and at the same time give some factual data concerning instances of such loss of life and damage to property, with special application to the mining industry.The annual loss of life and destruction of property by lightning is considerable; the former may be prevented to a limited extent, though use of common sense as to exposure is required and not always followed; the latter can be prevented to a considerable degree. The manufacturers of electrical equipment, through improved types of lightning arresters, have done much toward the protection of electrical equipment, with consequent safeguarding of life and of property. Education based on unfortunate experiences has gone far to discourage the handling of explosives and blasting accessories during thunder storms, especially in open pits and quarries, and to a much smaller extent in underground workings. The lowly lightning rod plays an important role in the protection of certain types of buildings (especially isolated buildings), stacks, monuments, and other structures.LIGHTNING PHENOMENAIn 1751, Franklin proved that, lightning was simply a visible display of electricity - an extended spark; and until a generation ago little had been added to his exposition to define the various phases of the phenomenon. Matters pertaining to lightning are discussed in the following references:"

Apr 1, 1948

By Robert L. Lagace

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal minus. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to determine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m2 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to he attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry for the years 1964-65. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By Perry D. Teitelbaum

In two earlier studies the Federal Bureau of Mines undertook to explore comprehensively the dimensions of the Nation's energy balance. The first of these studies, published in 1950 as Bureau of Mines Information Circular 7582, by Harold J, Barnett, was primarily concerned with projections of future domestic energy requirements and supplies, because these related to projected growth in major fuel-consuming sectors of the economy, changing rates of energy-use efficiency, and interfuel substitution patterns. But, to provide the essential background for these projections, it was first necessary to assemble and examine in some detail the quantitative information on the size and shape of the current United States fuel economy. Among other things, Barnett's path-breaking study indicated the need to consider energy as an entity, particularly for public and private policy makers, industry and commodity analysts, economists, and others concerned with long range questions of domestic and international energy supply and demand. The study also spotlighted a gap in the fabric of current economic intelligence; no comprehensive collation and reconcilation in any single report of available published statistical information covering the origin -a disposition of all energy materials existed. In response to this latter need, the Bureau of Mines prepared the second of the two studies referred t3 above. This was published in 1951 as Report of Investigations 4805, by W, H, Lyon and D, S. Colby, and it consisted of statistical information on the production and use of each of the various fuels and electric energy in the United States for 1929, 1939, and 1947; all were presented in tabular form and on a uniform basis. The three years selected were chosen largely on the basis of data availability.

Jan 1, 1961

By Harold J. Bennett

The purpose of this study was to develop methods for the financial evaluation of mineral deposits. This includes the selection of the best alternative mining and processing methods and production rates. This was done by performing a financial evaluation through computer simulation using sensitivity and probabilistic risk analysis. The criterion used to measure the relative advantages of these investment and operating alternatives is the discounted-cash-flow rate of return. Included is a description of the theory and methods used in the probabilistic analysis approach, which is based on the premise that the expression of a range of values in establishing an estimate for a parameter is more realistic than the choice of a single value. Numerous simulations are made using randomly selected values of the input parameters resulting in a frequency distribution of the rates of return and their relative probability of occurrence. The sensitivity analysis method is described and combined with the probabilistic analysis to interrelate mineral reserves, capital investments, operating costs, and production rates. The ability to vary these input parameters on successive runs has permitted the selection of the best alternative mining and processing methods and production rates for a given mineral deposit. For illustrative purposes the evaluation of a mineral deposit was performed using three alternative mining and processing methods at three different quantities of resources and various production rates and prices. The computer program used in this analysis was written in FORTRAN II for maximum compatability and should run without modification on most computers having BK (8,000-word) core memory, a card reader, and printer (120 characters per line).

Jan 1, 1970

The realization that there is a limit to our supply of domestic mineral and fuel resources, which have been taken for granted until recently, has stimulated the need for conservation and optimum utilization of the Nation's minerals, metals, and fuels-resources critical to our national economy. The mission of the Bureau of Mines is to develop new technology, improve existing technology, and disseminate information related to mineral resources and industries. Fulfilling the mission is necessary to insure a continuing, adequate supply of minerals and alternative supplies of energy from reliable sources at the lowest possible cost to society and the environment. Established in 1910, the Bureau of Mines under the Department of the Interior is the Federal Government's primary research arm in the mineral field. Since the transfer of the fossil fuels portion of the energy research program to the newly organized Energy Research and Development Administration (ERDA) in fiscal year 1975, Bureau research has been concentrated on increasing mineral production, decreasing energy usage through more efficient processing, and decreasing material losses caused by corrosion. Concurrently, research is being addressed to improved coal-preparation techniques, especially to expanding utilization of low-grade coals and coals difficult to beneficiate, which are essential for reducing the need for petroleum and natural gas supplies and for redirecting our energy consumption. Fluctuations in the availability of foreign sources of minerals, metals, and fuels due to political and economic variability among nations have necessitated intensified investigation into coal mining, uranium-ore processing, and geothermal energy sources-three alternatives that can help to alleviate the dependence of the United States on foreign sources of energy.

Jan 1, 1975

By R. V. Higgins, A. J. Leighton

A computer program has been devised to calculate the reservoir performance of water floods of complicated well - spacing patterns . The method and program have been tested by calculating the waterflood performance of fivespot patterns using oils of different viscosities and the performance calculations agreed closely with laboratory results . The program on a high - speed digital computer will process the performance prediction in about 1 minute , which is very rapid for a prediction using so much fluid mechanics and nonlinear geometry . The program has been presented in such a way that one may use it as given and save the time required to write and " debug " one of his own . gram processes a complex reservoir analysis , many of the complicated steps are explained in detail , both for the fluid mechanics and the directions for the computer . The subtle features that originally delayed the application of the program to unusual combinations of permeability and viscosity relationships are incorporated and explained

Jan 1, 1963

By William W. Aljoe

The hydrologic characteristics of two abandoned underground coal mine sites, near Latrobe, PA, and Uniontown, PA, were investigated by the U.S. Bureau of Mines for possible implementation of alkaline injection into the mine pools as a means of abating their acid discharges. The Latrobe site was chosen for a one-time application of alkaline injection to achieve a partial, short-term neutralization of a limited portion of the mine pool. A quantity of alkaline reagent (sodium hydroxide) sufficient for a one-time neutralization of the water in this portion of the pool was added. Although nearly all of the neutralizing reagent had moved away from the injection wells within 6 weeks, no evidence of neutralization was noted at the mine discharge during the study period. This lack of neutralization probably occurred because the injection wells did not intercept a primary flow path through the mine. Criteria for successful application of alkaline injection at this or other sites include (1) positive identification of the primary flow paths through the mine pool and (2) addition of quantities of alkaline reagent sufficient to neutralize the entire volume of the pool along the primary flow path.

Jan 1, 2010

By C. N. Adams

The purpose of this investigation was to evaluate the physical and mechanical properties of high-purity titanium made by two processes. Sodium-reduced metal with 58 Brinell hardness number (B.h.n.) and electrorefined metal with 60 B.h.n. and 70 B.h.n. were used. Titanium of these hardness levels did not work-harden excessively, and beyond 40 percent cold work the hardening effect was not great. Rapid softening occurred when the metal was annealed at temperature between 300° and 600° C. Full annealing, as determined by property and microstructure studies, was accomplished after 30 minutes at 700° C. A recrystallization diagram is presented which is based on determinations of annealed grain size as a function of rolling reduction and annealing time. For reductions of less than 20 percent, exaggerated grain growth occurred during annealing; for reductions greater than 20 percent, the variation in grain size for each annealing temperature was minor.

Jan 1, 1961

By Roswell W. Prouty

As part of a general plan for control and economic utilization of the waters of the Missouri River Basin as well as development of its inherent power resources, the Corps of Engineers of the United States Army has under construction a rolled earth dam near the site of old Fort Randall in South Dakota. The dam is in Charles Mix and Gregory Counties on the Missouri River at a point about 922 miles above its mouth. It is approximately 125 air-line miles southeast of Pierre and 55 miles southwest of Mitchell, S. Dak. The storage reservoir to be formed by the dam will extend upstream for 150 miles and, at maximum operating pool level, will cover an area of some 107,000 acres. It will have a storage capacity of 6.2 million acre feat.

Jun 1, 1949

By Khamis Y. Haramy

This U.S. Bureau of Mines report describes the use of Bureau-developed flat and cylindrical hydraulic borehole pressure cells. A brief description of the fabrication, installation, and pressurizing equipment is given and pressurizing procedures are discussed. Theories available on evaluation of data from the flat and cylindrical pressure cells and examples of data analysis and stress evaluation are also presented.

Jan 1, 1991

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

By John H. Hild

"INTRODUCTION Alunite occurs within a radius of 10 miles of Marysvale, Piute County, Utah, in veins and as replacements of igneous rocks. A number of each type of deposit was explored by the Bureau of Mines, in cooperation with the Geological Survey, under the Strategic Minerals program during 1942. The exploratory work comprised geologic and topographic mapping, diamond drilling,,bulldozer and hand trenching, sinking test pits, rehabilitation of old workings, sampling alunite exposures, and constructing and repairing roads.ACKNOWLEDGNENTSIn its program of exploration of mineral deposits; the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches-are under the supervision of Dr. R. S. Dean, assistant director.With particular reference to this publication, acknowledgment is given to Richard E. Mieritz and William E. Young, who assisted on the project at various times; P. T. Allsman, chief. Salt Lake Division, Mining Branch, who advised on exploratory problems and gave valuable assistance in preparing the report and illustrations; A. P. T. Schumann, for preparing the illustrations; and to Gordon L. Bell, Max Willard, and Eugene Callaghan, of the Geological Survey, who cooperated as representatives of that agency."

Nov 1, 1946

By William M. Thornton

[Owing to the comparatively high freezing point of nitroglycerin (14, 15, 16, 17, 18, 23, 37, 38)3/ - 1.9° C. and 13.0° C. for the labile and stabile modifications, respectively, as determined by Hibbert (16) - manufacturers of dynamites have incorporated into the liquid portion of these composite explosives various substances capable of participating in an explosion, to depress the above-mentioned freezing point. Aromatic nitro-compounds, chiefly nitrobenzenes, nitrotoluenes, and nitronaphthalenes, have been used to a considerable extent (11), but such nitrosubstitution products have not proved altogether satisfactory, as has been shown clearly by Naoúm. (14). Consequently there has been a strong tendency in recent years to replace them with one or more of several nitric esters, among which the following (29, 35) have been prominent: Dinitrochlorhydrin (monochlorhydrin dinitrate); nitrosugars, for example, sucrose octanitrate (19); tetranitrodiglycerin (diglycerin tetranitrate); nitroglycol (ethyleneglycol dinitrate); and diethyleneglycol dinitrate (13, 46, 47). Of these, nitroglycol (33, 4l, 45, 48, 49, 65) is outstanding in importance. As the Bureau of fines is naturally interested in the analytical chemistry of the "explosive oils," it seemed desirable to bring together in this report the widely scattered experimental work covering the problem of differentiation that has appeared in various chemical and physicochemical publications.]

Jan 1, 1941

By Alice V. Peter

The rare-earth group are among the least familiar of the 92 known elements. Moreover, the relatively few people who have even heard of the rare earths ordinarily regard them merely as very rare elements having unusual names but doubtful commercial application. This typical attitude can be attributed partly to the fact that no commercial uses have been developed for most of the members of the group and partly to the fact that those which do enter into useful articles do so anonymously. Most people speak with a degree of familiarity of the "chromium" plating on their automobiles or household appliances; "antimony" ash trays and cigarette boxes are on sale in many department stores; and "tungsten" lamps and even "molybdenum" steels are advertised in popular magazines. However, the average user of a pocket cigarette lighter is not conscious that the important sparking element is a "flint" made from ferrocerium, and if he does chap on to inquire about the composition he is likely to be told that it is "sparking alloy", "misch metal", or 'pyrophoric alloy." Similarly, the wearer of spectacles made of "Crookes" or other tinted glass probably is not aware that the light softening effects are due to the presence of rare-earth oxides, or that the arc light on his street may owe its brilliance to cerium fluoride in the carbon electrode. Despite a variety of practical applications, however, most of the rare-earth metals still must be listed as scientific curiosities. In fact, little is known as to the properties which may make them useful products at some future date. Meanwhile it is important to note that Nature has been relatively generous in her distribution of the rare earths and that adequate supplies of most of them will be forthcoming when these elements have proved their worth as commercial products.

Jan 1, 1935

By D. C. Dahlin

The U.S. Bureau of Mines investigated the magnetic susceptibility of minerals as a function of mag-netic field strength to determine how it might affect the potential for high-field magnetic separation as an alternative to other separation technologies. Single-mineral concentrates were prepared from specimens from the same deposit to compare magnetic susceptibilities of minerals that occur together and from specimens from different deposits to compare magnetic susceptibilities of like minerals. A vibrating-sample magnetometer with a superconducting magnet capable of producing a magnetic field of 7.16 x 106 Aim (90 kOe) was used to measure the magnetic moment of the samples. The data were then converted to specific magnetic susceptibility data and plotted as a function of magnetic field strength. Cursory studies were also completed on the effects of iron content and oxidation roasts on magnetic susceptibility in high fields. The results showed that magnetic susceptibility is essentially constant in magnetic fields above those needed to saturate ferromagnetic constituents. Although magnetic susceptibility is influenced by iron content and by thermal treatment, the changes are not large enough to influence separations in fields above 1.59 x 106 Aim (20 kOe).

Jan 1, 2010

By Norma R. Golumsic

Gasoline and other liquid fuels may be obtained from coal by direct and indirect hydrogenation.3/ The direct process, usually termed the coal-hydro-genation or the Bergius process, was patented in Germany by F. Bergius in 1914 and developed to a commercial stage by the inventor and I. G. Farben-industrie. From a chemical point of view, the coal-hydrogenation process consists of adding hydrogen to the complex coal molecules and removing oxygen so that its chemical constitution is changed to that of petroleum, whereupon the coal substance liquefies, yielding an aromatic crude oil. In the indirect-hydrogenation process, known as the Fischer-Tropsch process (invented by Franz Fischer and Hans Tropsch in Germany), coal, lignite, or natural gas is first converted to water gas, a mixture of carbon monoxide and hydrogen. This mixture of gases, in proper proportion and after suitable purification, is then passed over a solid catalyst at relatively low pressures (1 to 20 atmospheres) and temperatures ranging from 180° to 260° C. The products obtained are gasoline, Diesel oil, liquefiable gases, and paraffin wax.

Jan 1, 1946

By Lloyd Williams

1. This investigation shows that the Sewanee bed is the only coal bed being mined in Sequatchie County. Other coal beds are present, but as they do not contain known recoverable reserves, estimates of reserves were made only for the Sewanee bed. 2. Known measured and indicated reserves in the Sewanee bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 76 million short tons as of January 1, 1953. Of this total 62 million short tons represent coal 28 inches and more thick. Areas in the bed were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1955

By Jr. Fish

As a part of a study of iron are resources in the Appalachians, 9 diamond drill holes aggregating 1,580.7 feet were drilled in a portion of the Butt Mountain area of northeastern Giles County, Virginia. Three hematitic sand-stone beds were intersected in the Clinton formation but only one was consistent in thickness and grade in all 9 drill holes. This bed averages 18.9 percent iron over an average thickness of 24 feet. The drill cores were logged and chemical analyses were made on 161 individual samples and 22 composite samples. Beneficiation studies were made of three composite hematitic sandstone samples each representing a separate bed containing 14.6, 19.8 and 20.0 per-cent iron. Major mineral constituents of the samples were hematite, quartz, and sericite.

Jan 1, 1967